Polycarbonate & Flex-Line-Steel Universal Pole
Mount Installation Guide
TerraWave's enclosures are intended for indoor OR outdoor use and are
commonly used in harsh environments. These enclosures protect WLAN
equipment from damage caused by inclement weather and tampering.
Proper mounting of the enclosure is essential in ensuring safety and
reliability of your network. Below is a simple guide demonstrating the
step by step installation process utilizing a universal pole mount kit and
can be used with a polycarbonate or Flex-Line Steel enclosure.
Polycarbonate Pole Mount Kit Includes:
 Mounting Bolts (4)
 Flat Washers (4)
 Lock Washers (4)
 Mounting Flanges (2)
 Hose Clamps (2)
Flex-Line Steel Pole Mount Kit Includes:
 Mounting Bolts (4)
 Flat Washers (4)
 Lock Washers (4)
 Sealing Washers (4)
 Nuts (4)
 Mounting Flanges (2)
 Hose Clamps (2)
Additional Components Needed
 Philips Screwdriver and 10mm Deep Socket
wrench
 Flat Screwdriver or 8mm Socket
Universal Pole Mount Kit
Polycarbonate Fastener Pack
Mounting Flanges
www.terra-wave.com
Email: sales@terra-wave.com
Phone: 1-800-851-4965
Flex-Line Fastener Pack
Polycarbonate & Flex-Line-Steel Universal Pole
Mount Installation Guide
Polycarbonate Enclosure Installation Instructions:
1. Place mounting flange on the back of the enclosure (Figure 1). Place the flat side of the flange onto the
back of the enclosure, exposing the brass inserts within the horizontal slots.
2. Using the bolts, lock washers and flat washers provided, secure the flanges to the back of the enclosure at
the top and bottom (Figure 2). Tighten, but do not over torque, the bolts using a Phillips screwdriver and
10mm deep socket. No power tools should be used.
3. Once both flanges are installed on the back of the enclosure (Figure 3), it is ready to be easily mounted to
a pole (Figure 4).
4. Feed the provided hose clamps through the slots in the mounting flange (Figure 5) then wrap the hose
clamp around your the and feed through slot on the opposite side of the mounting flange.
5. Tighten the hose clamp with a flat screwdriver or 8mm socket (Figure 6) until the clamp is secure around
the pole.
Placement of Mounting Flange
Figure 1
Secure Mounting Flange
Figure 2
Mounted Flanges
Figure 3
Hose Clamp Installation
Figure 5
Upright Enclosure with Flanges
Figure 4
www.terra-wave.com
Email: sales@terra-wave.com
Phone: 1-800-851-4965
Tighten Hose Clamp
Figure 6
Polycarbonate & Flex-Line-Steel Universal Pole
Mount Installation Guide
Flex-Line Steel Enclosure Installation Instructions:
1. Remove the (4) hole plugs on the back of the Flex-Line enclosure, exposing mounting through holes.
2. Place mounting flange on the back of the enclosure. The flat side of the mounting flange should be flush
against the back of the enclosure, exposing mounting through holes within the horizontal slot (Figure 1).
3. Using the provided bolts, lock washers, sealing washers, flat washers and nuts, secure the flanges to the
back of the enclosure at the top and bottom using one of the below options.
Option 1—Bolt head inside enclosure:
1. Use sealing washer on the inside of the enclosure and flat washer, lock washer and nut on the
outside of the enclosure (Figures 2 & 3).
Option 2—Bolt head outside enclosure:
1. Use sealing washer, lock washer and nut on the inside of the enclosure and flat washer on the
outside of the enclosure (Figures 4 & 5).
4. Tighten, but do not over torque, the bolts using a Phillips screwdriver and 10 mm deep socket. No power
tools should be used.
Once both flanges are installed on the back of the enclosure, it is ready to be easily mounted to a pole
(Figure 6).
5. Feed the provided hose clamps through the slots in the mounting flange (Figure 7) then wrap the hose
clamp around the pole and feed through slot on the opposite side of the mounting flange.
6. Tighten the hose clamp with a flat screwdriver or 8mm socket (Figure 8) until the clamp is secure around
the pole.
Option 1—Bolt head inside enclosure
Placement of Mounting Flange
Figure 1
Inside of Enclosure
Figure 2
Outside of Enclosure
Figure 3
Option 2—Bolt head outside enclosure
Hose Clamp Installation
Figure 7
Finished Enclosure
Figure 6
Inside of Enclosure
Figure 4
Tighten Hose Clamp
Figure 8
www.terra-wave.com
Email: sales@terra-wave.com
Phone: 1-800-851-4965
Outside of Enclosure
Figure 5