S��� S���™
OEM INSTALL MANUAL
Rev: 04.28.2015
Page 1
Sure Step™ OEM Install Manual
TABLE OF CONTENTS
Introduction
Preparation
Tools Required
Measurements
Installation
Operation
Adjusting Lower Legs
Rev: 04.28.2015
3
3
3
3
4
5
6
Page 2
Sure Step™ OEM Install Manual
Introduction
The Sure Step™ is an entry step that can be mounted in several locations, removing constraints that RV
floor plan designers have faced for years. The new aluminum quad entry step assemblies fasten to the
RV sidewall, rear wall, exterior slide-out wall or over a wheel well, allowing manufacturers to create more
versatile and customized RV floor plans.
NOTE: The sidewall of the RV MUST have sufficient backing material for securing the Sure Step™ assembly.
Preparation
Tools Required
- Tape measure
- #10 x 1" self-tapping screws (x12) (OEM supplied)
- Screw gun (with appropriate fastening bit)
Measurements (Fig. 1)
1.
2.
3.
Measure the entry door where the steps will be installed to determine which step assembly will be
needed. Doors less than 25" wide can use 325669 (27" assembly). Doors up to 28" wide can use 354008
(30" assembly). This product cannot be used on doors wider than 28".
Find the horizontal center of the entry door. When attaching the step assembly to the sidewall, it
should be centered horizontally under the entry door.
Measure down from the bottom of the entry door 8 inches. The top of the top step of the assembly
should be aligned with this mark when the steps are extended.
Entry Door
Fig. 1
RV Sidewall
Door Width
Sure Step™ Mounting Arm
8"
Rev: 04.28.2015
Page 3
Sure Step™ OEM Install Manual
Installation
1.
2.
If not already completed, complete the Measurements section on the previous page to ensure the Sure
Step™ assembly can and will be installed properly. Also ensure that sufficient backer is in place in the
sidewall where the mounting arms will be attached.
Align the Sure Step™ assembly as described in the Measurements section on the previous page.
NOTE: Ensure that the steps are level with the RV before fully attaching the mounting arms to the sidewall.
3. Screw the left-hand mounting arm to the sidewall with one #10 x 1" self-tapping screw in the upper
left mounting hole. Only tighten the screw until snug. This will allow for any necessary adjustments to
align the Sure Step™ assembly with the unit.
4. Once the assembly is aligned with the unit, screw the right-hand mounting arm to the sidewall using
one #10 x 1" self-tapping screw.
5. Check the alignment of the steps. If necessary, remove the screw from the mounting arm and realign.
6. Once the alignment is assured, fill the rest of the screw holes (10x) with #10 x 1" self-tapping screws.
Ensure all screws are tightened (Figs. 2 and 3).
Fig. 2
Fig. 3
Mounting Arm
#10 x 1" Self-Tapping
Screws (x12)
Mounting Arm
#10 x 1" Self -Tapping
Screws (x12)
NOTE: Steps shown unfolded for clarity.
Rev: 04.28.2015
Page 4
Sure Step™ OEM Install Manual
Operation
1.
Unlatch the lower legs from the bottom step (Figs. 4 and 5). Swing lower legs out from the step.
Fig. 5
Fig. 4
Latched
Lower Leg
2.
Unlatched
Lower Leg
Once lower legs are released from the bottom step, unlatch the step assembly at the top of the
mounting arms by loosening the locking knob, and swinging the latch up and around (Figs. 6 and 7).
There is one latch on each side of the assembly.
Fig. 6
Fig. 7
Latch
Locking Knob
Mounting
Arm
Locking Knob
Mounting
Arm
Latch
Fig. 8
3.
Unfold the step assembly until the footpads of the lower
legs touch the ground (Fig. 8).
NOTE: When fully unfolded, the steps should be level with the
RV. If the steps are not level, follow the instructions on
the next page for adjusting the lower legs.
Foot Pad
Rev: 04.28.2015
Page 5
Ground
Sure Step™ OEM Install Manual
4.
Once the steps are unfolded and in place, turn the keyed cam lock on the upper right-hand mounting
arm until the cam is in the horizontal position (Figs. 9 and 10). This is a safety feature that ensures the
steps cannot be folded up and latched into place, potentially trapping a person inside the RV.
Fig. 9
Fig. 10
Keyed
Cam Lock
5.
Keyed
Cam Lock
To fold the steps back into the travel position, reverse the previous steps. Ensure both latches are
engaged and that both locking knobs are tightened prior to moving the RV.
Adjusting Lower Legs (Fig. 11)
1.
2.
3.
4.
To adjust the height of the lower leg, remove the cotter pin from the adjustment pin.
Remove the adjustment pin from the lower leg assembly.
Adjust the height of the leg up or down as needed.
Replace the adjustment pin into the lower leg assembly and secure it with the cotter pin.
Fig. 11
Cotter
Pin
Adjustment
Pin
Foot Pad
Rev: 04.28.2015
Page 6
Sure Step™ OEM Install Manual
NOTES
Rev: 04.28.2015
Page 7
Sure Step™ OEM Install Manual
The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”). LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an
authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty. The information contained in this manual is subject to change without notice and at the sole discretion of LCI. Revised editions are available for free download from www.lci1.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert Components, Inc.
Ph: (574) 537-8900 | Web: www.lci1.com | Email: warranty@lci1.com
Rev: 04.28.2015
Page 8
Sure Step™ OEM Install Manual