INSTALLATION INSTRUCTIONS
For models:
DTDC-30-LED-120
DTDC-30-LED-120-A (with arm; see pg. 3)
DTDC-LED
Dusk-to-Dawn
FIXTURE MOUNTING
Note: Assure that fixture is mounted to a
structurally sound surface that will support the
fixture.
Warning
Please read instructions carefully before attempting
to install fixture and retain instructions for future
reference.
Caution: To avoid electrical shock hazard.
•
Turn off the electricity before installing or
servicing this fixture.
•
2. Place mounting section of fixture onto desired
mounting surface, mark and drill holes for
mounting.
3. This fixture can be mounted with three lag
screws which are provided. See Figure 1, 26.
4. Install the two bottom lag screws first.
5. Place the fixture on the two bottom lag screws
and install the top lag screw.
6. Tighten the top lag screw first and then tighten
the remaining lag screws.
Electrical connections need to comply with
National Electric Code and Local Electric Code.
•
1. Select a location on a structurally secure wall or
pole, minimum 4 feet from the ground.
The fixture should be installed by a qualified
electrician.
General Safety Information
WARNING:
1. Before making any wiring connections, make
sure power is disconnected.
2. Do not touch the yellow portion of the LED
when removing the acrylic refractor. Damage
may occur.
FIXTURE WIRING
Note: Connect fixture to supply wires, make sure
power is off.
1. Feed supply wires through arm and make
wiring connections in the fixture.
2. Connect the black fixture wire to the black
house power supply wire and the white fixture
wire to the white house supply wire first.
3. The fixture must be grounded. Attach ground
lead to green ground screw. See Figure 1, 23.
4. Secure the cover plate with two screws, two
nuts and washers. See Figure 1. 20,21,25.
FIGURE 1
Fixture Descriptions
1. Housing
2. Photocell
3. O-ring
4. Nut
5. Driver Bracket
6. Driver
7. Screws
8. Screw with Washer
9. LED
10. Washer
11. Screws
12. Cable Clamp
13. Screw with Washer
14. Wire Nut
15. Gasket
16. Reflector
17. Screw with Washer
18. Acrylic Refractor
19. Head Screws
20. Hex Nuts
21. Washers
22. Cover Plate
23. Hex Screw with Washer
24. Wire Grommet
25. Screws
26. Lag Screws
Technical Specifications
Input voltage: 120v 50/60Hz
Lumen Output: 1800 lm
Color Temperature: 4100K
Photocell: 120v
ARM MOUNTING
Note: To avoid the possibility of electrical shock, turn off power supply before installing or servicing.
1. Loosely install carriage bolts with lock
washers and nuts into wall mount bracket.
2. Install wall mounting bracket to mounting
surface with lag bolts provided.
3. Insert short end of arm into mounting
bracket.
4. Feed ground wire up through arm.
5. Feed driver wires down through arm.
6. Using hex bolts and arm bracket, secure the
housing to the arm.
NOTE: When installing the housing on to the
arm, allow 1/4” (6.4mm) spacing between
end of arm and the housing to prevent the
ground wire from being pinched.
7. Install green ground screw on arm bracket at
location marked “GND” and tighten ground
screw to ground wire.
8. Wire black fixture lead to the incoming hot
lead and the white lead to the incoming
neutral lead.
FIGURE 2
Short End
of Arm
Carriage
Bolts
Ground
Screw
Wall
Mounting
Bracket
Arm
Bracket
Hex
Bolts
Lag
Bolts
China patent no. ZL201030601090.2
US patented