Input/Output
Modules
Features That Make a Difference:
•
Provides cost-effective expansion of
input and output capacity
•
Compatible with full range of
Software House iSTAR and apC
access control panels
•
Locate modules up to 1,220 m (4,000 ft)
away from controllers using flexible twowire RS-485 RM bus
•
Reduces length of sensor and control
wiring to save installation costs
•
I8 provides eight Class A supervised inputs
•
R8 provides eight Form C relay outputs
•
I8-CSI, configurable supervised input
model, allows use of existing input wiring
without changing end-of-line (EOL)
resistors
•
Three status LEDs per input (red/yellow/
green) and one per output enable quick
diagnostics and troubleshooting
•
Small, modular size requires minimal panel
space
•
Dedicated tamper input included on each
module
•
Optional UL-listed enclosure available
www.swhouse.com
The Software House I8, R8, and I8-CSI
modules provide a flexible, cost-effective
means to expand the input and output
functionality of any iSTAR or apC access
controller. Common applications include
alarm monitoring and control and elevator
control.
The I8 input module provides eight
Class A supervised inputs. Three LEDs
per input help the installer commission and
troubleshoot each input circuit – red if the
input is in alarm, green for normal, and
yellow for a supervision error. LEDs may be
turned off via a DIP switch setting.
The I8-CSI module enhances the
functionality of the standard I8 module by
supporting numerous supervised circuit
types and EOL resistance values. This allows
the I8-CSI to accommodate existing field
wiring without changing EOL resistors. More
than 20 different circuit types are supported.
The circuit type is selected via a bank of DIP
switches and applies to all eight inputs on
the I8-CSI.
The R8 output module provides eight Form
C dry contact relay outputs. A red status
LED per output shows the state of the relay.
All modules feature a dedicated input for
an external cabinet tamper switch and
mount easily in the Software House
RM-CAN or RM-DCM-CAN enclosure.
The modules communicate with iSTAR or
apC controllers via the two-wire RM bus
that allows total wiring distances of up to
1,220 m (4,000 ft). Up to eight I8s and
eight R8s can be connected to each apC,
iSTAR eX, and iSTAR Pro eight-reader
model; up to 16 of each module can be
connected to the iSTAR Pro 16-reader model.
The modules are fully compatible with both
C•CURE 800/8000 and C•CURE 9000.
Specifications
General
Dimensions (H x W) . . . . . . . .
Environmental . . . . . . . . . . . . .
Power Input Voltage . . . . . . . .
Tamper . . . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . .
Regulatory . . . . . . . . . . . . . . .
11.0 x 15.0 cm (4.3 x 5.9 in)
0° to 50° C (32° to 122° F);
5 to 85% relative humidity, non-condensing
12 VDC +/- 10%
Dedicated input for external tamper switch
0.23 kg (8 oz)
UL 294, UL 1076, FCC Part A, CE,
EN 50133, RoHS
I8 Input Module
Power Requirements . . . . . . .
Inputs . . . . . . . . . . . . . . . . . . .
LEDs per Input . . . . . . . . . . . .
180 mA @ 12 VDC
Eight Class A supervised
Red (alarm), green (normal), yellow
(supervision error)
R8 Output Module
Power Requirements . . . . . . .
Outputs . . . . . . . . . . . . . . . . .
LED Per Output . . . . . . . . . . .
Relay Contact Ratings . . . . . .
45 mA @ 12 VDC plus 32 mA per active relay
Eight Form C dry contact relays
Red (relay active)
30 VDC, 2.0 A resistive
30 VDC, 1.0 A inductive
125 VAC, 0.4 A
Optional Metal Enclosures with Tamper Switch
RM-DCM-CAN
Dimensions . . . . . . . . . . . . . 356 x 305 x 89 mm (14 x 12 x 3.5 in)
Capacity . . . . . . . . . . . . . . . Up to four input or output modules
RM-CAN
Dimensions . . . . . . . . . . . . . 210 x 184 x 83 mm (8.25 x 7.25 x 3.25 in)
Capacity . . . . . . . . . . . . . . . One input or output module
I8-CSI Input Module
Power Requirements . . . . . . .
Inputs . . . . . . . . . . . . . . . . . . .
LEDs per Input . . . . . . . . . . . .
Ordering Information
180 mA @ 12 VDC
Eight Class A supervised, configurable via
DIP switch
Red (alarm), green (normal), yellow (supervision error)
Circuits Supported . . . . . . . . . Single resistor: 1K, 5K, 10K
Double resistor: 1K, 5K, 10K,
1K/2K, 6.8K/18K, 200/10K
Unsupervised: NO, NC
Model Numbers
Description
AS0073-000
I8 input module
AS0073-CSI
I8-CSI input module
AS0074-000
R8 output module
RM-DCM-CAN
Large metal enclosure with tamper switch
RM-CAN
Small metal enclosure with tamper switch
Wiring Summary
Signal
From
To
Belden #
Gauge
# of Pairs
Shielded
Maximum Length
Comm (two-wire RS-485)
apC/iSTAR
I8/R8
9841*
24
1
Yes
1,220 m (4,000 ft)
Power
apC/iSTAR
I8/R8
9841*
24
1
No
Based on voltage drop
Control Point
R8
Strike, Siren, etc.
8442/8461
18
1
No
Based on voltage drop
Supervised Input
I8
REX or Door Contact
8442/8461
22/18
1
No
610 m (2,000 ft)
1
ON
S3
P7
1
DS26
S3
1
DS22
DS7
U3
ING
Y1
DS6
DS21
DS20
DS5
FOR SWH STD 1K DUAL S2:3-4, S3:1-4 = OFF
SEE QUICKSTART DOC FOR OTHER SETTINGS
CYCLE POWER AFTER SETTING
P3
P6
1
DS19
"WARNING Damage may result from incorrectly
wiring power terminals, input and output lines, and
central-supervising station lines. Check all
connections before powering the unit."
DS8
INF
DS17
S2
S2
P5
1
P4
3 4
DS9
DS18
2
DS10
INE
DS16
DS15
DS12
SW1
DS11
ASSEMBLED IN USA
C
1
ON
1
DS13
COPYRIGHT 2007
TYCO
SOFTWARE HOUSE®
18–CSI BOARD
0312–5008–01 Rev.
Input Rating P9
12VDC 125mA
DS14
Refer to Quick Start Installation Guide,
P/N UM-218, Rev B0, July 2008
Note: Control, supervised, and unsupervised input cables must be shielded for FCC Class B operation.
Approvals
Readers
INH
DS24
DS23
S1
P2
P8
DS25
4
3 4
3
2
2
GND
S1
DS27
I8-CSI Input Module Configuration
I8 Input Module Configuration
P10
P5
1
2
3
1
-D
1
Related Products
iSTAR Controllers
SW1
NOTE: All mounting holes are 1/8" dia.
Max. component height 1/2".
(*) For plenum or underground applications, use Belden 89182 for one pair 22 AWG, 100 ohm 12.95 pf/ft.
C•CURE 9000
2 3 4 56
1
7
8
0
F
9
E DC B A
+D
DS3
IND
3
2
1
P6
1
2
3
+12V
DS2
1
P4
TAMPER
INPUT
P7
1
2
3
GND
DS4
INC
3
2
1
1
2
3
1
P3
R8 OUTPUT MODULE
AS-0074-000 REV.A
SOFTWARE HOUSE
MADE IN USA
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
TS
DS1
S1-1 ON = LED Power
S1-2 ON = Disable Tamper
S1-3 ON = Not Used
S1-4 ON = 485 Termination
1
1
P1
INB
3
2
1
W1
P8
NO
P2
C
NC
NO
C
NC
NO
C
NC
NO
C
NC
NO
P9
1
3
2
1
1 2 3 4
P9
P1
INA
R8 Output Module Configuration
Wiring Configuration Diagram
www.swhouse.com
© 2014 Tyco Security Products. All Rights Reserved. SH0146-DS-201410-R01-LT-EN
Tyco and the product names listed above are marks and/or registered marks. Unauthorized use is strictly prohibited.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative.
Pb
Pb-Free