Actiontec Elec. Inc. What does it mean when the LED lights on a M1000 DSL Router flash and or change color? POWER LED: Possible colors are: Red, Amber and Green Normal: When the M1000 DSL Router is functioning normally, the Power light will change color as the DSL Router is starting up. During a normal device power up, the Power LED is first solid Red for 2 to 3 seconds, followed by flashing Green for 15 to 30 seconds. Lastly the Power LED is solid Green, and it remains solid Green for the rest of the time the DSL Router is powered up. Abnormal: Power LED not illuminated: Either the device is turned off or some element of the power supply has failed. Possibly the AC power at the outlet, DC power from the Power Supply or DSL Router itself. Power LED is solid Red: Indication of possible hardware generated lockup, hardware failure or incorrect firmware. Power LED is solid Amber: Indication of firmware generated lockup or firmware corruption or incorrect firmware. Power LED only flashes Green, cycles through colors or M1000 restarts continuously: Indicates possible incorrect Power Supply voltage, corrupt or incorrect firmware. DSL LED: Possible colors are: Green Normal: When the M1000 DSL Router is working correctly, the DSL LED will begin flashing almost as soon as the Router is powered up. The DSL LED can flash at two different speeds. The modem begins by flashing at the slower speed when the DSL cable is not connected or it can not detect a DSL signal. Once a signal is detected the LED begins flashing at a much faster rate. The change in speed is easy to see since it is approximately twice that of the slower speed. When the LED begins flashing at the higher rate, it will not be long before the DSL signal is acquired, and the modem is trained up. The DSL must remain trained up (Solid Green DSL LED) for the modem to make an Internet connection. Abnormal: DSL LED not illuminated: This is typically due to a Router firmware being loaded onto a DSL Router. Though unlikely, other reasons could be a corrupt firmware or hardware failure. DSL LED flashes continuously, never training up (DSL LED is never solid Green): If the LED is flashing slowly it indicates that the DSL modem does not detect a DSL signal. Possible reasons could be that the DSL line is crossed, incorrectly connected or bad. Other reasons might be that there really is no signal on the DSL line, because it has not been provisioned yet, it was configured incorrectly or configured on another line. If the LED is flashing quickly it indicates that the DSL modem sees the signal but that there is too much noise on the line for it to be able to train up. This could be because the DSL line has too much noise, because the DSL Filters are incorrectly installed or because the DSL Filters are not installed at all. If the DSL LED goes through the normal steps, but then after it becomes solid Green it starts flashing all over again, and goes through the steps from the beginning again and again, it too indicates noise on the DSL line. Just like the quickly flashing LED it could be because the DSL line has too much noise, because the DSL Filters are incorrectly installed or not installed at all. Page 1 of 2 Actiontec Elec. Inc. INTERNET LED: Possible colors are: Red and Green Normal: A Green LED indicates a successful connection to the ISP (Internet Service Provider). When the connection is made the LED becomes Green and remains solid Green, until it begins to flash when network and Internet traffic begins to pass through it. However, the Internet connection can not be made, until the DSL has trained up and the DSL LED is solid Green. Abnormal: The DSL LED would still need to be solid Green, but after it is, if Internet LED turns Red it indicates that when it attempted to connect to the ISP, it failed. This type of failure is often due too authentication failure or some other type of misconfiguration of the Router by the user or DSL account misconfiguration by the ISP. Internet LED not illuminated: Indicates that there is no connection to the Internet or it was lost, that the DSL Router may still need to be configured, the DSL LED may be flashing (i.e. not trained up or lost train) or if the Internet connection is up, the Internet LED may have failed. LAN, USB or Ethernet LED: Possible colors are: Green Normal: The LED is illuminated when there is a successful connection to another device, such as a USB cable connected to a PC or an Ethernet cable connected to a computer or network hub. The LAN, USB and Ethernet LEDs are solid Green when there is a connection, and begin flashing when there is network traffic. Abnormal: LAN, USB and Ethernet LED not illuminated: Indicates no connection, either a bad cable, wrong type of cable or a bad USB or Ethernet port on the PC or Router. Wireless LEDs: There are 2 LEDs on the W1000 Wireless Module, Power and Wireless Possible colors are: Green Normal: The Wireless LED behaves differently than the LAN, USB and Ethernet LEDs do. Those LEDs are illuminated when a network device has connected. On the W1000 the Power LED is illuminated as soon as the module is plugged in, as is the Wireless LED. However, the Wireless LED being illuminated does not indicate that a network device has connected to it. The only indication that a computer or some other network device has connected is when the network traffic from that device causes the Wireless LED to flash. Abnormal: W1000 LEDs are illuminated but there is no connectivity: Indicates the M1000 was probably not restarted after the Wireless module was connected. The M1000 must be restarted after the W1000 Wireless module is connected or removed. Resolutions: These types of problems can often be resolved by power-cycling the Router or resetting it (See the FAQ regarding Resetting the M1000, for directions). Before replacing a DSL Router a Recovery should always be attempted, unless the problem is obviously a physical one (rattles, smoke, etc…). Many times reinstalling the firmware via a Recovery program can restore an unresponsive unit, to full functionality. Page 2 of 2