Fixed Rate Turn Signal Flasher
Installation Guide
This device is a solid state universal turn signal flasher, it will self balance to provide a consistent oem flash rate
regardless of load variations. This device is a direct plug and play replacement for the most popular motorcycle relay
types, but will also work with many other relay types, such as the Suzuki flasher with built in side stand switch (Suzuki
part number 38610-03F00). The device is universal, and can also be wired in to replace with any series flasher relay
type. NOTE: vehicle flasher locations may vary, common locations are under the seat, or behind the headlight or gauge
cluster.
Yamaha WR250X/R Installation
Make sure your vehicle is OFF. Remove your seat and left
side panel. Your OEM turn signal flasher location is shown
in the picture to the right (red circle shows plug location,
oem flasher has already been removed in the picture).
Squeeze the connector and gently pull to unplug the OEM
flasher. Plug in the 12oclockLabs Fixed Rate Flasher.
Secure the new Flasher with the provided zip ties to
prevent it from vibrating or bouncing around. Turn you
ignition switch ON, and test your turn signal flashers.
Start your vehicle, and test your turn signal flashers.
Installation is complete; reattach your side panel and
seat.
Honda CRF250L Installation
Make sure your vehicle is OFF. Remove the
right side cover that houses the coolant tank,
as shown in the picture to the right. Squeeze
the connector and gently pull to unplug the
OEM flasher. Plug in the 12oclockLabs Fixed
Rate Flasher. Secure the new Flasher with the
provided zip ties to prevent it from vibrating
or bouncing around. Turn you ignition switch
ON, and test your turn signal flashers. Start
your vehicle, and test your turn signal
flashers. Installation is complete; reattach
your side panel.
Suzuki DRZ400S/SM Installation
Make sure your vehicle is OFF. Behind your
headlight on the left side is your 7pin turn signal
relay. Unmount the relay socket and remove the
light blue wire and the orange wire from the
socket using a paperclip or small jeweler
screwdriver (see far right picture). Once the
wires are removed insert them into the provided
plastic housing (see picture directly to the right).
Reinstall the stock relay, and also plug in the
12oClockLabs Flasher into the newly installed
socket (both relays must be installed). Secure
the new Flasher with the provided zip ties to
prevent it from vibrating or bouncing around.
Turn you ignition switch ON, and test your turn
signal flashers. Start your vehicle, and test your
turn signal flashers. Installation is complete;
remount your relay socket.
Installation for Suzuki Relay (Suzuki Part Number: 38610-03F00)
Make sure your vehicle is OFF. The picture to the right shows the Suzuki 7pin relay.
The upper portion of the picture shows the BOTTOM view of the relay pins. Pins F
and G control the turn signal flashing.
Terminal F is NEGATIVE. Terminal G is POSITIVE.
We are going to access the socket this relay plugs
into, and slide terminals F and G out of the socket
housing. Unplug the relay and set it aside for now,
we will need to access the relay socket.
Using a paperclip or small jeweler screwdriver
remove the F and G pins from the relay socket on
your motorcycle (make sure to mark where they go
inside the original socket or take a picture in case
you want to return them later)
Referencing the picture to the right;
Slide the F pin into the Positive connector slot.
Slide the G pin into the Negative connector slot.
Reinstall the stock relay, and also plug in the 12oClockLabs Flasher into the newly
installed socket (both relays must be installed). Secure the new Flasher with the provided zip ties to prevent it from
vibrating or bouncing around. Turn you ignition switch ON, and test your turn signal flashers. Start your vehicle, and
test your turn signal flashers.
Manual Wiring Installations
Remove your existing turn signal flasher relay. Activate your left or right turn signal. Turn the ignition switch to the ON
position. Using a volt meter measure across the relay socket terminals to determine which terminal is positive, and
which is negative. Install the turn signal flasher using the provided wires and connector housing, refer to the picture
above so that you insert the wires into the correct slots of the housing connector. Make sure the ignition switch is OFF
before performing any wiring on the motorcycle.
Honda CBR250R Installation
Make sure your vehicle is OFF. Using a paperclip or small jeweler
screwdriver remove the pins with the black wire and gray wire from the
relay socket on the motorcycle (make sure to mark where they go
inside the original connector in case you want to return them later)
Slide those pins into the provided connector (see picture to the right).
Then on the relay socket of the motorcycle, you will jumper the Orange
wire, to the Orange wire with stripe. And jumper the blue wire, to the
blue wire with stripe. Now you can plug in the 12oClockLabs Flasher
into the newly installed socket.
Custom Wire Harness Installations
Positive should connect to a 10amp ignition switched positive source.
Ground should connect to turn signal handlebar switch “turn signal common”.
Turn signal handlebar switch LEFT signal output will connect to LEFT turn signal indicator light positive lead.
Turn signal handlebar switch RIGHT signal output will connect to RIGHT turn signal indicator light positive lead.
LEFT and RIGHT turn signal indicator light grounds will connect to ground.
Product Care & Precautions:
Mount this product away from extreme Heat. Close engine and exhaust contact should be avoided. Mount this product in a
relatively dry area, though the unit is weather proofed, it is a good idea to avoid frequently wet areas. Make sure to mount this
product in a location where it will not be crushed. Make sure to mount this product away from spark plug coil and wires, minimum
distance is at least twelve inches.
Disclaimer:
By using this product you agree to assume all risk and liability therein, and not hold responsible 12oclockLabs for any mishap
(either foreseeable or unforeseeable) that may arise from using or misusing this product; this includes all items sold or distributed
by 12oClockLabs. All electronic devices are subject to possible failure during normal usage, and by using this product you agree to
assume the risk and liability for such a possible failure.
3 Year Limited Warranty:
In the event of product failure due to normal usage, 12oclockLabs may elect to repair or replace your product, for a period of 3
years from product purchase date; at their option. This warranty does not cover damage from misuse, neglect, alteration, or self
repair. 12oclockLabs will determine if any damage incurred was not due to normal product usage. This limited warranty applies to
the original purchaser of the product, and is transferable to a new owner with proof of purchase.
Manual Revision 0.92