GIRA
Info
LED locator light
Installation Instructions
Order no.: 1159 ..
LED locator light
Order no.: 1161 ..
Order no.: 1162 ..
Function
The LED locator light is used in switch combinations
or as an individual light.
It helps to locate switches and to find your way in dark
rooms.
Due to its technical characteristics, the LED locator
light is not suitable for use in safety applications or as
an emergency light.
Safety warnings
Attention: Electrical equipment must be installed
and fitted only by qualified electricians and in observance of the applicable accident prevention
regulations.
To prevent electric shocks, disconnect the power supply before working on the LED lopcator
light (by cutting out the circuit breaker).
Any non-observance of the fitting instructions
may cause fire or other hazards.
Fitting
The LED locator light is directly connected to 230 V
AC with the terminals supplied (fig. A).
If desired, the light can be switched on and off with a
mechanical switch or a relay switching insert.
i
Important
The LED locator light is not dimmable. Connection
of the device to a dimmer may cause damage to the
dimmer and to the LED locator light.
The LED locator light must not be operated together
with an electronic switching insert (e.g. Tronic or
triac insert).
The switching inserts may otherwise be damaged.
LED locator light
11/05
Page 1 of 3
GIRA
Info
LED locator light
Installation Instructions
Removal of the LED locator light (fig. C)
Fitting instructions for waterproof type (IP 44)
(fig. B)
1. Loosen the Torx screws (3).
To obtain degree of protection IP 44, the light
must be assembled as follows:
2. Stick screwdriver into the corresponding openings
(2) in the frame and detach cover plate.
1. Insert sealing collar (1) together with support ring
(2) into the flush-mounting box and fasten with the
screws supplied (3).
3. Stick screwdriver into the corresponding openings
(1) of the LED locator light and detach the light.
2. Bring frame (5) into correct position and fasten with
plugs (4) and screws (6) on the wall.
3. Snap LED locator light (8) onto the frame making
sure that the condensed-water openings (7) are at
the bottom.
4. Put cover plate (10) in place and secure with the
Torx screws (9).
LED locator light
11/05
Page 2 of 3
GIRA
Info
LED locator light
Installation Instructions
Technical characteristics
Rated voltage:
AC 230 V ~, 50 Hz
Ambient temperature:
-15 °C to max. 50 °C
Power consumption:
6,5 VA
Power factor λ:
0,1
Connecting wires
Phase (L):
Neutral conductor (N):
Cross-section:
Length:
brown (BN)
blue (BU)
0.75 mm²
100 mm
Type / Order no. Colour of light Number of
LEDs
1161 ..
white
6
1162 ..
blue
6
1159 ..
orange
8
Important:
LED production tolerances may result in visible
differences in brightness and colour.
Acceptance of guarantee
We accept the guarantee in accordance with the corresponding legal provisions.
Please return the unit postage paid to our central service department giving a brief description of the
fault:
Gira
Giersiepen GmbH & Co. KG
Service Center
Dahlienstrasse 12
D-42477 Radevormwald
The CE sign is a free trade sign addressed exclusively to the authorities and does not include
any warranty of any properties.
Gira
Giersiepen GmbH & Co. KG
Postfach 1220
D-42461 Radevormwald
Telefon: +49 / 21 95 / 602 - 0
Telefax: +49 / 21 95 / 602 - 339
Internet: www.gira.de
LED locator light
11/05
Page 3 of 3