Vulkan Product catalogue

advertisement
OUTDOOR
References
4
Autarkic lighting (self sufficient lighting)
20
Technical luminaires
22
Catenary luminaires
28
Cylindrical luminaires
32
Light columns
36
Bell-shaped luminaires
38
Heritage luminaires
40
Façade and wall lights
42
Poles and brackets
46
Heritage poles and brackets
54
Intelligent lighting
56
List of abbreviations
62
List of symbols
63
Guarantee
64
Nordeon Group
66
5
REFERENCES
7
Vulkan
Outdoor
References
Providing lighting when and where it is needed.
Routes such as service roads and side roads are lit at
night even if this isn't even necessary. Our goal is only to
illuminate areas when light is actually needed. Integrating
sensors helps to optimize the light output without
impacting on convenience or safety. The integrated motion
detector can reduce the light intensity to a minimum.
As soon as a sensor detects traffic, the light intensity
increases to a specified value. At the same time, this
command is sent to two previously defined adjoining
luminaires to ensure consistent lighting for the entire
section."
"INTEGRATED MOTION
DETECTORS GUARANTEE
INTELLIGENT ENERGY SAVING
WITHOUT NEGLECTING
SAFETY!"
Sascha Müller, product manager
Product V3630 outdoor luminaire
Project Nordeon production site, Springe, Germany
9
Vulkan Outdoor References
Off-grid lighting using wind power with maximum efficiency
- 100 000 hours without maintenance.
"WITH THE PROCEEDONE
SOLUTION, WE HAVE
PRODUCED LIGHTING
FOR PATHS AND STREETS
REQUIRING NO CONNECTION
TO THE MAINS POWER
SUPPLY. WE ARE PROUD TO
BE PROMOTING CARBONNEUTRAL SOLUTIONS."
Peer Langemak, head of development at noordforce GmbH
Customer The island of Juist in the North Sea
Product V3630 outdoor luminaire and Proceed One
11
Vulkan Outdoor References
The island of Texel in northern Holland is a pioneer in
carbon-neutral living. By the year 2020, the island aims
to produce no carbon whatsoever. As well as setting up
its own power supply based on solar systems and tidal
power plants, huge energy savings, especially from street
lighting, will help the island meet its goal. The Vulkan LED
luminaire V3630 is very important to this project. This
modular and efficient luminaire has impressed the Texel
community.
The V3630 is available in many different performance
levels and is supplied with an open-source light
management system integrated in the luminaire. Using
an open-source solution gives the community on Texel
maximum freedom in using existing or new management
systems.
"THE MODULAR DESIGN OF
THE V3630 MAKES IT THE
IDEAL LUMINAIRE FOR US.
IT DELIVERS EXACTLY WHAT
WE NEED: TAILORED ENERGY
EFFICIENCY AND LIGHT."
Stefan Kikkert, manager of public lighting for the Texel community
Customer The island of Texel
Product V3630 outdoor luminaire
13
Vulkan Outdoor References
Sustainability and energy-saving lighting with a special
charm.
"ONE OF THE BEST TIMES TO
BE AT THE HARBOUR IS IN
THE EVENING WHEN THE
SUN IS GOING DOWN AND
TWILIGHT IS SETTING IN.
THE APPROPRIATE CHARM
IS CREATED BY USING THE
RIGHT LIGHTING. THE LIGHT
COLUMN FROM VULKAN IS A
REAL EYE-CATCHER OFFERING
GREAT POTENTIAL SAVINGS."
Klaus Schmidt, technical manager
Customer Lelystad harbour, Netherlands
Product Light column
15
Vulkan Outdoor References
Car parks need to be well lit to give users a sense of security at
night.
"POWERFUL AND RELIABLE
LIGHTING MAKE THIS CAR
PARK A PLACE WHERE
DRIVERS AND PEDESTRIANS
FEEL REALLY SAFE AGAIN.
THE V3630 IS A GREAT
EXAMPLE OF EFFICIENT AND
HOMOGENOUS LIGHTING."
City of Bellegarde, France
Customer City of Bellegarde, France
Product V3630 outdoor luminaire
Project Effia car park, Bellegarde, France
17
Vulkan Outdoor References
Heritage luminaires produce and underpin the charm of
historical buildings, bridges or districts.
"TAKE A STROLL ON THE
FAMOUS PÖPPELMANN
BRIDGE AND GET LOST IN
YOUR DREAMS THANKS TO
THE TRADITIONAL HERITAGE
LIGHTING FROM VULKAN,
WHICH SLOTS PERFECTLY
INTO THE HISTORICAL
TOWNSCAPE OF GRIMMA."
Frank Sprenger, project manager
Product Heritage luminaire V7420
Project Pöppelmann Bridge, Grimma, Germany
19
Vulkan Outdoor References
Robust in a tough environment: seawater-resistant finish
protects the luminaire from weathering.
"THE V3457 CYLINDRICAL
LUMINAIRE IS THE IDEAL
MATCH FOR THE TOWNSCAPE
AND IS VERY ATTRACTIVE.
BY REPLACING THE OLD
MERCURY VAPOUR LAMPS,
WE ARE ALSO MAKING HUGE
ENERGY SAVINGS. "
Ralf Liedke, head of sales
Customer City of Lütjenburg, Germany
Product Cylindrical luminaire V3457
21
PRODUCTS
23
Vulkan
Self-sufficient lighting
ProceedOne
OFF-GRID LIGHTING USING WIND POWER
Rotor
Material
Surface
Rotor height
Rotor diameter
Operating speed
Braking point
PROCEEDONE
•
Quick & easy mounting thanks to foundation pipe and
modular design (pole, luminaire and generator)
•
Off-grid power supply and low start-up costs
•
High efficiency thanks to Vulkan luminaires with very long
lifetime of up to 100 000 hours
•
Good security of supply – PROCEED ONE power is generated
as of wind strengths of 3 m/s
•
Powerful battery provides power for up to 10 days even
without wind
V3630
INTELLIGENT LIGHTING CONTROL
•
Generator (coreless, permanently excited, 3-phase disc generator)
Diameter
230 mm
Rated voltage
28 V
Rated power
200 W
Rated speed
300 rpm
Battery system
LiFePo4 batteries
Rated voltage
Capacity
Charge cycles
V3630
12.8 V
60 Ah -> 720 Wh
> 2000, approx. 50 charge cycles / year
Luminaire (Vulkan V3630 or V3610 – LED technical street luminaire)
Electrical power
14W
Operating voltage
12V DC
Pole
Galvanised light column
Total length
Pole height
Embedded base
Spigot size
Bracket
Spigot size for bracket
Wall thickness
Conicity
PRODUCTS FOR PROCEED ONE
V3610
PROCEED ONE
aluminium AlMg3 W19, seawater-resistant
powder coated
available in 800 / 900 / 1000 mm
380-520 mm
150-350 rpm (adjustable)
as of 330 rpm (adjustable)
Electronic regulation of light output; automatic
reduction in lighting depending on individual setting and
battery charge
•
Motion detectors (planned for the end of 2016)
•
The daily illumination time and dimming profiles can be
programmed and can be adjusted as required.
7000 mm
5800 mm
1200 mm
121 mm
0.5 m 15°
76 mm
4 mm
10.0
System
Total height
Light source height
Standard lighting time per day
the equivalent of a charge of
Battery life before charging is needed
with 5h of lighting / day
7.0-7.4m
6.0m
0-5 hours,
0-70Wh
10 days
CHARGE TIME FOR 10 DAYS OF LIGHTING OF 5H ON EACH DAY
(W)
15 min
1h
1000
800
2h
600
400
200
8h
28 h
3
6
10
14
18
IP66 IK08
Wind (m/s)
100 000 h
L80/B10
25
Vulkan
Technical luminaires
V3610
MAXIMUM FLEXIBILITY FOR INDIVIDUAL APPLICATIONS
OPTICS AND APPLICATIONS
V3610
•
All components are designed for a very long lifetime of
100 000 hours
•
Smooth and flat aluminium housing acts as a heat sink –
without cooling fins which are prone to dirt
•
Universal and rapid mounting
•
No light pollution from directed light
•
6 inclination levels adjustable in 5° increments
Flat single-pane tempered safety glass, partially printed on the inside in black; easy to open thanks to
quick-release lock with 90° rotation, enclosure glass can be hinged towards the pole
optics O1 - major thoroughfares; O3 - low-order thoroughfares; O4 - narrow roads, cycle paths and walkways;
O7 - thoroughfares and residential streets
Luminous flux
650lm to 5600lm - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white); >Ra70
System power
6.5W to 58W
Protection rating
I or II
Surface vulnerable
to wind
approx. 5.8 - 6.7 kg
Finish
DB 703 or RAL 7035, others on request
ELECTRICAL SPECIFICATION
LED technology
Narrow roads,
Thoroughfares
thoroughfares
cycle paths and
and residential
walkways
streets
Current
1x LED
2x LED
3x LED
200 mA
620lm / 6.5W
1270lm/ 12W
1960lm / 18.3W
300 mA
890lm / 9.1W
1830lm / 17.1W
2770lm / 25.8W
350 mA
1020lm / 10.4W
2100lm / 19.7W
3190lm / 29.6W
400 mA
1150lm / 11.8W
2350lm / 22.3W
3570lm / 33.5W
500 mA
1390lm / 14.6W
2830lm / 28W
4280lm / 41.4W
600 mA
1610lm / 17.5W
3280lm / 33.8W
4930lm / 49.5W
700 mA
1820lm / 20.6W
3700lm / 39.4W
5520lm / 57.7W
SIX INCLINATION LEVELS
FROM -5° TO + 20°
ADDITIONAL SPECIFICATION
Housing
High-quality LED modules, each with 8
highly efficient high-power LEDs with
up to 170 lm/W
Installation
Powder-coated die-cast aluminium
Pole top diam. 60-76mm
Pole top mounting with six inclination levels from -5° to + 20°
Side mounted luminaire diam. 42-60mm
Constant Lumen Management (CLM);
Aluminium core PCB for
optimum thermal management
LED module frame to reduce scatter
loss to a minimum
Minor
DIMENSIONAL DRAWING IN MM
8, 16, or 24 LEDs
Integrated, electronically controlled
temperature monitoring
Optics O7
Major
Rated power and luminous flux rounded and averaged, 4000K. Data may differ if using different optics.
0.05m²
Weight
Optics O4
4000K OUTPUT EXAMPLE
Lighting of roads that complies with EN 13201; lens optics made from PMMA in multi-layer technology
Optics
Optics O3
thoroughfares
GENERAL SPECIFICATIONS
Enclosure
Optics O1
autonomous performance reduction for
Light
operation in networks without a control line
regulation
(Light Regulation Autarkic - LRA);
performance reduction by switching off a
control line (Light Regulation Twin - LRT)
Monitoring
Thermal monitoring of
LED unit and operating device
Digital communication with DALI
Overvoltage
protection
Integrated; surge voltage resistance
of 6kV (L-N) and 8kV (L/N earth), 10kV
on request
(LMS) with monitoring, error messages,
For brackets without
inclination,
5° inclination is possible
Radio-controlled Light Management System
motion control and other features
IP66 IK08
100 000 h
L80/B10
For brackets with inclination
of up to 20° can be inclined
down to 0°
27
Vulkan Technical luminaires V3630
ONE DESIGN FOR ALL APPLICATIONS WITHIN A CITY
OPTICS AND APPLICATIONS
V3630
•
System efficiency of up to 122 lm/W
•
Very long life: 100 000 hours L80B10
•
Universal and rapid assembly with just one screw
•
Flexibility in mounting on pole top and as side mounted luminaire,
integrated pole flap
•
Heat sink integrated in housing design for optimum and efficient
thermal management
Optics
Optics O2
Optics O3
Optics O4
Optics O5
Optics O6
Optics O7
Major
Minor
Low-order
Narrow roads,
Open spaces
Pedestrian
Thoroughfares
thoroughfares
thoroughfares
cycle paths and
and public
crossings
and residential
walkways
area lighting
thoroughfares
Current
1x LED
2x LED
3x LED
4x LED
200 mA
1200lm / 12W
2300lm / 23W
3500lm / 33W
4800lm / 42W
250 mA
1450lm / 14.4W
2800lm / 27W
Optics O1 - major thoroughfares; O2 - thoroughfares; O3 - low-order thoroughfares; O4 - narrow roads,
300 mA
1700lm / 16.8W
3300lm / 32W
5000lm / 47W
6800lm / 61W
cycle paths and walkways; O5 - open spaces and car park lighting; O6 - pedestrian crossings; O7 - thoroughfares and
350 mA
1950lm / 19.2W
3800lm / 36.5W
400 mA
2200lm / 22W
4200lm / 41W
6500lm / 62W
8800lm / 80W
7800lm / 76W
10500lm / 100W
9200lm / 91W
12500lm / 120W
10500lm / 106W
14000lm / 140W
Enclosure made from flat single-pane tempered safety glass with bicolour printing; easy to open thanks to
quick-release lock with 90° rotation, enclosure glass can be hinged towards the pole
residential streets
Luminous flux
1200lm to 14.000lm - L80B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white) or 5000K (cold white); >Ra70
450 mA
2400lm / 24W
4700lm / 46W
System power
12W to 140W
500 mA
2600lm / 26.5W
5200lm / 51W
Protection rating
I or II
550 mA
2900lm / 29W
5600lm / 56W
600 mA
3100lm / 31.5W
6000lm / 61W
650 mA
3300lm / 34W
6400lm / 66W
700 mA
3500lm/ 36.5W
6800lm / 71W
to wind
Side: A = 0.06 m²
Weight
approx. 9.2 to 10.5 kg
Finish
DB 703 or RAL 7035, others on request
ELECTRICAL SPECIFICATION
LED technology
High-quality LED modules, each with 16
highly efficient high-power LEDs with
up to 170 lm/W
Rated power and luminous flux rounded and averaged, 4000K. Data may differ if using different optics.
ADDITIONAL SPECIFICATION
Housing
Installation
Powder-coated die-cast aluminium
Side mounted luminaire diam. 42-60mm
Integrated, electronically controlled
temperature monitoring
autonomous performance reduction for
Monitoring
Overvoltage
protection
6kV (L-N) and 8kV (L/N earth), 10kV
available as option
INCLINATION LEVELS FROM 0° TO + 15°
Pole top diam. 60-76mm
Aluminium core PCB for
optimum thermal management
Thermal monitoring of
LED unit and operating device
DIMENSIONAL DRAWING IN
MM
Constant Lumen Management (CLM);
Light regula-
operation in networks without a control line
tion
(Light Regulation Autarkic - LRA);
performance reduction by switching off a
Side mounted
luminaire:
diam. 42-60
mm
690
Pole top:
diam. 60-76
mm
130
Surface vulnerable
streets
4000K OUTPUT EXAMPLE
GENERAL SPECIFICATIONS
Enclosure
Optics O1
control line (Light Regulation Twin - LRT)
Digital communication with DALI
380
Radio-controlled Light Management System
(LMS) with monitoring, error messages,
motion control and other features
IP66 IK08
100 000 h
L80/B10
Angle of inclination can
be adjusted in 5° steps
from 0° to 15°
29
Vulkan Technical luminaires V5050
HIGHLY EFFICIENT WHIP POLE LUMINAIRE
V5050
•
All components are designed for a very long life of 100 000 hours
•
Substitute for linear luminaires for one or two fluorescent lamps
•
Directed light for high efficiency
•
Discreet, slimline and minimalist design
•
Flat, flush pane of glass for easy cleaning
Linear luminaire with one LED board
Linear luminaire with two LED boards
GENERAL SPECIFICATIONS
Enclosure
Enclosure made from flat single-pane tempered safety glass, inserted flush in the housing and glued from the inside;
weather-resistant EPDM gasket
Choice of various asymmetrical, wide-beam precision optics for optimum illumination of the relevant application; lens
Optics
optics made from PMMA in multi-layer technology; spring attachment for optics and LED that doesn't damage the
material
4000K OUTPUT EXAMPLE
Current
1x LED
2x LED
350 mA
1800lm / 18W
3630lm/ 37W
Luminous flux
1200lm to 3200lm (with 1 LED board) and 2300lm to 6700lm (with 2 LED boards) - L80/B10 for 100 000h
400 mA
2010lm / 21W
4070lm / 42W
Light colour
4000K (neutral white), 3000K (warm white); >Ra70
450 mA
2220lm / 23W
4500lm / 47W
System power
12 W to 37 W (with 1 LED board) and 23 W to 71 W (with 2 LED boards)
500 mA
2440lm / 26W
4930lm / 51W
Protection rating
I or II
600 mA
2840lm / 31W
5760lm / 62W
Side: A = 0.04 m² (with 1 LED board), side A= 0.06m² (with 2 LED boards)
700 mA
3210lm / 36W
6510lm / 72W
Surface vulnerable
to wind
Rated power and luminous flux rounded and averaged, 4000K. Data may differ if using different optics.
Weight
approx. 3 kg or 5.7 kg
Finish
Housing in DB 702, pole top in DB 703, powder-coated or customer's choice
ELECTRICAL SPECIFICATION
LED technology
Versions with one or two LED boards,
each with 16 high-power-LEDs with up
to 170 lm/W
Aluminium core PCB for
optimum thermal management
Integrated, electronically controlled
temperature monitoring
Monitoring
Thermal monitoring of LED unit and
operating device
Overvoltage
protection
Integrated; surge voltage resistance
of 6kV (L-N) and 8kV (L/N earth)
DIMENSIONAL DRAWING IN MM
ADDITIONAL SPECIFICATION
Housing
Installation
Light
regulation
(optionally
with dimmer
function)
Extruded aluminium section serves as
heat sink & efficient thermal management
Side mounted luminaire diam. 42-48mm
Constant Lumen Management (CLM);
autonomous performance reduction for
operation in networks without a control line
(Light Regulation Autarkic - LRA);
performance reduction by switching off a
control line (Light Regulation Twin - LRT)
Digital communication with DALI
IP65 IK10
100 000 h
L80/B10
31
Vulkan
Catenary luminaires
V3125
AERODYNAMIC SHAPE FOR CHALLENGING LIGHT CONDITIONS
V3125
•
All components are designed for a very long life of 100 000 hours
•
Smooth aluminium housing without cooling fins which are prone
to dirt
•
Flat, aerodynamic shape with low wind load
•
No light pollution from directed light
GENERAL SPECIFICATIONS
Enclosure
Enclosure made from flat single-pane tempered safety glass, partially printed on the inside in black; maintenance-free
concept; weather resistant EPDM gasket
Choice of various light distributions for various applications to ensure lighting of roads that complies with EN 13201;
Optics
lens optics made from PMMA in multi-layer technology;
spring attachment for optics and LED that doesn't damage the material
Luminous flux
2300lm to 6800lm (with 2 LED boards) and 4800lm to 10500lm (with 4 LED boards) - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white)
System power
23 W to 71 W (with 2 LED boards) and 42W to 100 W (with 4 LED boards)
Protection rating
I or II
Surface vulnerable
to wind
Side: A = 0.05 m²
Weight
approx. 9 kg
Finish
DB 703, others on request
ELECTRICAL SPECIFICATION
LED technology
DIMENSIONAL DRAWING IN MM
Versions with two or four LED boards,
each with 16 high-power-LEDs with up
to 170 lm/W
ADDITIONAL SPECIFICATION
Housing
Monitoring
Thermal monitoring of LED unit and
operating device
Overvoltage
protection
Integrated; surge voltage resistance
of 6kV (L-N) and 8kV (L/N earth), 10kV
on request
powder coated DB 703
Suspension, screws and
Aluminium core PCB for
optimum thermal management
Integrated, electronically controlled
temperature monitoring
Extruded aluminium section,
fastening components made from stainless
Attachment
steel;
Attachment mechanism for
suspension cable 8-12mm
Constant Lumen Management (CLM);
autonomous performance reduction for
Light regula-
operation in networks without a control line
tion
(Light Regulation Autarkic - LRA);
performance reduction by switching off a
control line (Light Regulation Twin - LRT)
IP66 IK10
100 000 h
L80/B10
33
Vulkan
Catenary luminaire
V3130
DISCREET CATENARY LUMINAIRE FOR ANY TOWNSCAPE
V3130
•
All components are designed for a very long life of 100 000 hours
•
Smooth aluminium housing, without cooling fins which are prone
to dirt
•
Narrow design for reduced visibility
•
No light pollution from directed light
•
Pane inserted flush for easy cleaning
GENERAL SPECIFICATIONS
Enclosure
Enclosures made from flat single-pane tempered safety glass, inserted into housing flush from the inside; easy
cleaning of single-pane tempered safety glass inserted flush; weather-resistant EPDM gasket
Choice of various light distributions for various applications to ensure lighting of roads that complies with EN 13201;
Optics
lens optics made from PMMA in multi-layer technology;
spring attachment for optics and LED that doesn't damage the material
Luminous flux
2300lm to 6800lm - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white)
System power
23 W to 71 W
Protection rating
I or II
Surface vulnerable
to wind
Side: A = 0.06 m²
Weight
approx. 6.3 kg
Finish
DB 703, others on request
ELECTRICAL SPECIFICATION
LED technology
DIMENSIONAL DRAWING IN MM
Versions with two LED boards, each
with 16 high-power-LEDs with up to
170 lm/W
ADDITIONAL SPECIFICATION
Extruded aluminium section serves as heat
Housing
der coated DB703
Aluminium core PCB for
optimum thermal management
Integrated, electronically controlled
temperature monitoring
Monitoring
Thermal monitoring of LED unit and
operating device
Overvoltage
protection
Integrated; surge voltage resistance
of 6kV (L-N) and 8kV (L/N earth), 10kV
on request
sink & efficient thermal management, powSuspension, screws and fastening
Attachment
components made from stainless steel;
Attachment mechanism for suspension
cable 8-12mm
Constant Lumen Management (CLM);
autonomous performance reduction for
Light regula-
operation in networks without a control line
tion
(Light Regulation Autarkic - LRA);
performance reduction by switching off a
control line (Light Regulation Twin - LRT)
IP65 IK10
100 000 h
L80/B10
35
Vulkan Cylindrical luminaires V3450 / V3456-V3458
DECORATIVE TOP-MOUNTED LUMINAIRE WITH TIMELESS, ELEGANT DESIGN
V3450 / V3456 - V3458
diam. 213
Weight: 10 kg
All components are designed for a very long life of 100 000 hours
SCx: 0.09m2
812
•
IP54
•
Dimensionally stable and corrosion resistant aluminium
•
Efficient thermal management thanks to built-in heat sink
3450
•
Interchangeable LED module with highly efficient high-power LEDs
•
Little glare thanks to large optics surface
Asymmetrischer und breitstrahlender Reflektor(MRC)
diam. 635
residential streets, pedestrian areas and for public area lighting
Luminous flux
1000lm to 3200lm - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white); >Ra70
System power
12 W to 38 W
Protection rating
I or II
Finish
DB 703, others on request
ELECTRICAL SPECIFICATION
LED technology
SCx: 0.1m2
4x4 arrangement with asymmetrical, wide-beam precision optics used to illuminate
Versions with two LED boards, each
with 8 high-power-LEDs with up to 170
lm/W
Aluminium core PCB for
optimum thermal management
diam. 635
ADDITIONAL SPECIFICATION
Housing
Input voltage
230V in accordance with DIN IEC38
Overvoltage
protection
Integrated; surge voltage resistance of
4kV (L-N) and 4kV (L/N earth) integrated
on the driver's PCB
Weight: 11 kg
SCx: 0.1m2
Dimensionally stable and corrosion resistant
aluminium
Structurally secure three-point pole attach-
Attachment
ment in pole top for pole spigot diameter
LED Modul LEVO
3457
of 76mm
Integrated thermal sensor to protect
the LED unit
against over-temperature
The fully encapsulated electronic components, equipped with an LED driver,
can be fully removed with few tools
LED Modul LEVO
3456
585
Optics
Weight: 11 kg
Acrylic (PMMA) cylinder glass, clear, satin-finished at top
Constant Lumen Management (CLM);
diam. 750
autonomous performance reduction for
Light regula-
operation in networks without a control line
tion
(Light Regulation Autarkic - LRA);
performance reduction by switching off a
590
Enclosure
585
GENERAL SPECIFICATIONS
control line (Light Regulation Twin - LRT)
Asymmetrischer und breitstrahlender Reflektor(MRC)
3458
IP65 IK06
100 000 h
L80/B10
Weight: 11 kg
SCx: 0.1m2
37
Vulkan
Cylindrical luminaires
V5470 / V5471
DECORATIVE TOP-MOUNTED LUMINAIRE WITH TRADITIONAL DESIGN
V5470 / V5471
598
All components are designed for a very long life of 100 000 hours
•
Available in two different housing shapes
•
LED module and driver can be replaced without any tools
•
Asymmetrical or symmetrical light distribution
•
Luminaire can be easily opened from above without any tools
•
Quick pole mounting using integrated grub screws
685
•
Weight: 10kg
SCx: 0.14m2
5470
GENERAL SPECIFICATIONS
Optics
Transparent polycarbonate enclosure, UV-resistant; weather-resistant rubber gasket
Asymmetrical light distribution for residential streets and pedestrian areas or
Luminous flux
1000lm to 3200lm - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white) >Ra70
System power
12W to 38W
Protection rating
I or II
Weight
10 kg
Finish
DB 703, powder coated, other colours on request
ELECTRICAL SPECIFICATION
LED technology
Versions with two LED boards, each
with 8 high-power-LEDs with up to 170
lm/W
Aluminium core PCB for
optimum thermal management
Weight: 10kg
SCx: 0.13m2
ADDITIONAL SPECIFICATION
Housing
Attachment
Easily interchangeable LED module
with plug connection for
automatic electrical isolation
of the LED module when opening
the luminaire
Electronic LED driver on
carrier plate with plug connection for
electrical isolation, if required
can be interchanged with ease
Dimensionally stable and corrosion resistant
aluminium
For pole spigot diameter of 76mm
5471
Constant Lumen Management (CLM), to
Integrated thermal sensor to protect
the LED unit
against over-temperature
Overvoltage
protection
332
symmetrical light distribution for public area lighting or pedestrian areas
688
Enclosure
compensate for drop in luminous flux over
life of LEDs; DALI light control for connecLight regula-
ting external controls; autonomous night-
tion
time dimming, ideal for networks without
a control line (Light Regulation Autarkic
- LRA); reduction by means of control phase
(Light Regulation Twin - LRT)
The luminaire body
opens without tools
Integrated; surge voltage resistance of
4kV (L-N) and 4kV (L/N earth) integrated
on the driver's PCB
IP66 IK10
100 000 h
L80/B10
39
Vulkan
Light columns
V6220 / V6230
REPRESENTATIVE ILLUMINATING COLUMNS FOR INDIVIDUAL URBAN DESIGN
230
V6220 / V6230
All components are designed for a very long life of 100 000 hours
•
Decorative illuminating column with timeless, elegant design
•
Can be tailored to your needs, diameter of 200mm or 230mm
•
Low glare thanks to large optics surface
•
Vertical pipe is connected with luminaire head via patented adapter ring
•
Different luminous intensity distributions
3000 - 4000
•
GENERAL SPECIFICATIONS
Fitted with wide-beam, asymmetrical, all-round or linear luminous intensity distribution.
Optional: an element can be installed to reduce the luminance within the optical system on the building side
Luminous flux
1000lm to 3200lm - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white) >Ra70
System power
12 W to 38 W
Protection rating
I or II
Finish
DB 703 powder coated, other colours on request
ELECTRICAL SPECIFICATION
LED technology
Versions with two LED boards, each
with 8 high-power-LEDs with up to 170
lm/W
Aluminium core PCB for
optimum thermal management
ADDITIONAL SPECIFICATION
Housing
Overvoltage
protection
Integrated; surge voltage resistance of
4kV (L-N) and 4kV (L/N earth) integrated
on the driver's PCB
6230
Dimensionally stable and corrosion resistant
Aluminium, powder coated
Round flange plate for attaching
Attachment
Integrated thermal sensor to protect
the LED unit
against over-temperature
Electronic LED driver on
carrier plate with plug connection for
electrical isolation, if required
can be interchanged with ease
6220
to foundations or available with
extended vertical pipe as buried base
As option can be supplied with integrated
Constant Lumen Management (CLM);
Light regulation (on
request)
autonomous performance reduction
(midnight point, can be programmed to
several levels) (Light Regulation Autarkic
- LRA), reduction in output via control line
(Light Regulation Twin - LRT) or using DALI
interface
IP65 IK06
100 000 h
L80/B10
2200
Optics
Luminaire glass made of acrylic, satin-finished or also available in crystal-clear version
1800
Enclosure
3500-5000
200
41
All components are designed for a very long life of 100 000 hours
•
Enclosure opens without tools
•
Rapid mounting using Vulkan Patent System (VPS)
•
Low glare thanks to large optics surface
•
Efficient thermal management thanks to in-built heat sink
SCx: 0.09m2
diam. 530
V8447
Weight: 9.0 kg
440
SCx: 0.14m
Luminous flux: 2000-5400lm
GENERAL SPECIFICATIONS
Optics
diam. 675
Acrylic outer casing (PMMA), clear or structured version
Available with asymmetrical light distribution for residential streets and pedestrian areas
Pedestrian areas; developed for lighting of streets, pathways and squares that complies with EN 13201
Luminous flux
2000lm to 5400lm - L80/B10 for 100.000h (for details, see on right)
Light colour
4000K (neutral white), 3000K (warm white); >Ra70
System power
Equipped with LEDs of between 20 W and 27 W
Protection rating
I or II
Finish
Standard finish in RAL colours and DB 703, other colours on request
V8448
Weight: 6.0 kg
SCx: 0.09m2
430
Enclosure
Luminous flux: 2000-2700lm
diam. 500
V8450
Single-part luminaire housing constructed
Housing
from dimensionally stable and
Aluminium core PCB for
optimum thermal management
corrosion-resistant aluminium
Integrated thermal sensor to protect
the LED unit
against over-temperature
system, with adapter also for 1/2" external
Weight: 9.0 kg
480
LED technology
Versions with several LED boards with
high-power LEDs
ADDITIONAL SPECIFICATION
SCx: 0.14m2
Luminous flux: 2000-3500lm
Pole attachment with VPS quick mounting
Attachment
diam. 520
threads; rosetten nut available for diffe-
If required or for maintenance purposes, the electrical unit can be
fully removed
ring diameters of pole bracket mounted
Input voltage
230V in accordance with DIN IEC38
Constant Lumen Management (CLM);
Overvoltage
protection
Integrated; surge voltage resistance
of 6kV (L-N) and 8kV (L/N earth),
10kV on request
luminaires
As option can be supplied with integrated
autonomous performance reduction
Light regula-
(midnight point, can be programmed to
tion
several levels) (Light Regulation Autarkic
- LRA), reduction in output via control line
V8466
Weight: 11 kg
500
ELECTRICAL SPECIFICATION
SCx: 0.14m2
Luminous flux: 2000-3500lm
(Light Regulation Twin - LRT) or using DALI
diam. 620
interface
LED Modul LEVO
Rated power and luminous flux rounded and averaged, 4000K.
Data may differ if using different optics.
IP65 IK06
100 000 h
L80/B10
4W
54
50
lm
-5
0W
-4
7W
50
41
lm
00
35
lm
-3
7W
-2
0W
lm
-2
50
27
lm
50
20
Weight: 6.0 kg
Luminous flux: 2000-2700lm
•
lm
-1
lm
50
12
V8446
370
V8446 / -47 / -48 / -50 / -66
-1
2W
DECORATIVE BELL-SHAPED LUMINAIRES WITH TRADITIONAL DESIGN
7W
V8446-8448 / V8450 / V8466
50
Bell-shaped luminaires
17
Vulkan
43
Vulkan Heritage luminaires V7410 / V7420
HERITAGE LUMINAIRES - LUMINAIRE DESIGN CLASSICS
V7410 / V7420
•
All components are designed for a very long life of 100 000 hours
•
Low glare thanks to large optics surface
•
Luminaire housing and pole top constructed from high-quality cast aluminium
•
Historic design for old city areas
GENERAL SPECIFICATIONS
Enclosure
Enclosure glass made from acrylic (PMMA), structured, as an option also clear, interchangeable if necessary
Available with asymmetrical light distribution for residential streets and pedestrian areas or with symmetrical light
distribution for public area lighting or pedestrian areas; developed for lighting of streets, pathways and squares that
complies with EN 13201
7420
Luminous flux
1000lm to 3200lm - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white); >Ra70
System power
12 W to 38W
Protection rating
I or II
Finish
Standard finish in RAL colours and DB 703, other colours on request
7410
DIMENSIONAL DRAWING IN MM
SW 440
Versions with two LED boards, each
with 8 high-power-LEDs with up to 170
lm/W
Housing
Luminaire housing and pole top constructed from high-quality cast aluminium
Aluminium core PCB for
optimum thermal management
Roof with attractive, classic palmettes, can
Integrated thermal sensor to protect
the LED unit
against over-temperature
Pole attachment with pole top with a G3/4"
The fully encapsulated electronic components, equipped with an LED driver,
can be fully removed with few tools
Input voltage
230V in accordance with DIN IEC38
Overvoltage
protection
Integrated; surge voltage resistance of
4kV (L-N) and 4kV (L/N earth) integrated
on the driver's PCB
395
910
LED technology
ADDITIONAL SPECIFICATION
910
ELECTRICAL SPECIFICATION
SW 440
790
Optics
also be supplied without palmettes
external thread for attachment to heriAttachment
LED Modul CLed (CLed easy)
tage poles or optionally with adapter for
cylindrical stepped poles with a pole spigot
V7420 without palmettes
V7420 with palmettes
diameter of 76mm
Constant Lumen Management (CLM);
autonomous performance reduction for
Light regula-
operation in networks without a control line
tion
(Light Regulation Autarkic - LRA);
performance reduction by switching off a
control line (Light Regulation Twin - LRT)
IP54 IK06
100 000 h
L80/B10
V7410
45
Vulkan Façade and wall lights V9010
FAÇADE AND WALL LIGHTS WITH MINIMALIST DESIGN
V9010
•
All components are designed for a very long life of 100 000 hours
•
12W LED as substitute for a TL58W moisture-proof lamp
•
Directed light for high efficiency
•
Discreet, slimline and minimalist design
•
Spring attachment for optics and LED that doesn't damage the
material
GENERAL SPECIFICATIONS
Enclosure
Enclosure made from flat single-pane tempered safety glass, inserted flush in the housing and glued from the inside;
weather-resistant EPDM gasket
Choice of various light distributions for various applications to light roads,
Optics
loading ramps, pathways, underpasses etc.; lens optics made from PMMA in multi-layer technology;
spring attachment for optics and LED that doesn't damage the material
Luminous flux
1200lm to 3000lm - L80/B10 for 100 000h
Light colour
4000K (neutral white), 3000K (warm white) >Ra70
System power
12 W to 37W
Protection rating
I or II
Weight
approx. 1.6 kg
Finish
DB 703, others on request
ELECTRICAL SPECIFICATION
LED technology
DIMENSIONAL DRAWING IN MM
ADDITIONAL SPECIFICATION
LED board versions with 16
high-power LEDs with up to 160 lm/W
Aluminium core PCB for
optimum thermal management
Integrated, electronically controlled
temperature monitoring
Monitoring
Thermal monitoring of
LED unit and operating device
Overvoltage protection
Integrated; surge voltage resistance of
6kV (L-N) and 8kV (L/N earth)
Electrical
connection
Connecting lead pre-installed
in the factory, 2m H07 RNF
High-quality extruded aluminium section,
Housing
which serves as heat sink and ensures optimum and efficient thermal management.
Powder coated, DB 703
Attachment
Wall attachment using slots for screws with a
diameter of 8mm
Constant Lumen Management (CLM);
autonomous performance reduction for
operation in networks without a control line
Light regula-
(Light Regulation Autarkic - LRA);
tion
performance reduction by switching off a
control line (Light Regulation Twin - LRT);
digital communication using DALI interface
for integration in external DALI controllers
IP65 IK10
100 000 h
L80/B10
47
Vulkan Façade and wall lights V9510
ROBUST 3-IN-1 FLOODLIGHT FOR FLEXIBLE LIGHTING
V9510
•
All components are designed for a very long life of 100 000 hours
•
Spotlight for use on the ground, wall or ceiling
•
Small LED spotlight for lighting signs, logos or similar applications
•
Directed light for high efficiency
•
Discreet, slimline and minimalist design
GENERAL SPECIFICATIONS
Enclosure
Enclosure made from flat single-pane tempered safety glass, inserted flush in the housing and glued from the inside;
weather-resistant EPDM gasket
Choice of various asymmetrical, wide-beam precision optics for optimum illumination of the relevant application, e.g.
Optics
signs, logos, pathways, ramps, etc.;
lens optics made from PMMA in multi-layer technology
Luminous flux
1200lm to 3000lm - L80/B10 for 100 000h
Light colour
4000K (neutral white) >Ra70, 3000K (warm white) >Ra80
System power
12 W to 37W
Protection rating
I or II
Surface vulnerable
to wind
Side: A = 0.05 m²
Weight
approx. 2 kg
Finish
DB 703, others on request
ELECTRICAL SPECIFICATION
LED technology
DIMENSIONAL DRAWING IN MM
Versions with two LED boards, each
with 16 high-power-LEDs with up to
160 lm/W
ADDITIONAL SPECIFICATION
High-quality extruded aluminium section,
Housing
Aluminium core PCB for
optimum thermal management
Integrated, electronically controlled
temperature monitoring
Monitoring
Thermal monitoring of LED unit and
operating device
Overvoltage
protection
Integrated; surge voltage resistance of
6kV (L-N) and 8kV (L/N earth)
which serves as heat sink and ensures optimum and efficient thermal management.
Powder coated, DB 703
Ground, wall or ceiling attachment using
Attachment
swivel-mounted brackets with slots for 6mm
screws; with H07 RN-F, 2m connecting lead
pre-installed in the factory
Available with various dimming functions
Light regulation
as options: "Constant Lumen Management"
(CLM); digital communication using
DALI interface for integration in external
DALI controllers
IP65 IK10
100 000 h
L80/B10
49
Vulkan Poles and brackets Cylindrical / conical
POLES AND BRACKETS
CYLINDRICAL
The cylindrical stepped poles are high-quality products from experts. They are manufactured in a flexible production
process and can therefore be adapted to your needs. Manufactured from steel pipe according to EN 10220 / DIN 1626,
hot-dip galvanised in accordance with DIN EN ISO 1461 and manufactured in accordance with DIN EN 40, you are
guaranteed lasting quality for your lighting systems. Poles up to a length of 14m can be coated using an environmentallyfriendly method to provide appropriate colours. We hold selected standard poles in stock for a rapid delivery service.
CONICAL
The conical poles are also high-quality products from experts. They are manufactured in a flexible production process and can be precisely adapted to your needs. Manufactured from steel pipe according to DIN EN 10025, hot-dip
galvanised in accordance with DIN EN ISO 1461 and manufactured in accordance with DIN EN 40, you are guaranteed
lasting quality for your lighting systems. Poles up to a length of 14m can be coated using an environmentally-friendly
method to provide appropriate colours. We hold selected standard poles in stock for a rapid delivery service.
Conical pole (STK) diameter 76 mm, wall thickness 3 mm
Cylindrical stepped pole (STZ) diameter 76 mm, wall thickness 2.9 mm
Fig. of conical pole
LPH
Fig. 2 - Pole with several steps
Fig. 1 - Pole with one step
LPH
E
L1
L2
L3
d1(E+L1)
d2
T
Fig.
3000
700
1000
2000
-
114 × 3.2
-
500
1
3500
700
1000
2500
-
114 × 3.2
-
500
1
4000
700
1000
3000
-
114 × 3.2
-
500
1
4500
800
1200
3300
-
114 × 3.2
-
600
1
5000
800
1500
3500
-
114 × 3.2
-
600
1
5500
800
1500
4000
-
114 × 3.2
-
600
1
6000
1000
2000
4000
-
114 × 3.6
-
600
1
6500
1000
1500
2000
3000
114 × 3.6
89 x 3.2
600
2
7000
1000
1500
3000
2500
114 × 3.6
89 x 3.2
600
2
8000
1200
1800
3000
3200
133 × 3.6
89 x 3.2
600
2
All dimensions in mm
• Standard dimensions of pole door:
85 × 400mm
• Triangular door look made from V2A, 10 mm
• Plain earthing link with two M6 sliding nuts and M8 earth connection
• Buried base with a
150 × 50 mm cable in-feed
• Without cable junction box and other accessories – please order separately
E
d1(E+L1)
T
Pole door
3000
700
128
600
85 x 400
3500
700
135
600
85 x 400
4000
800
129
600
85 x 400
4500
800
134
600
85 x 400
5000
800
140
600
85 x 400
5500
900
146
600
85 x 400
6000
1000
153
600
85 x 400
6500
1000
159
600
85 x 400
7000
1000
164
600
100 x 400
8000
1200
177
600
100 x 400
• Standard dimensions of pole door: 84 x 400 mm
• Triangular door look made from V2A, 10 mm
• Plain earthing link with two M6 sliding nuts and M8 earth connection
• Buried base with a 150 × 50 mm cable in-feed
• Without cable junction box and other accessories – please order separately
All dimensions in mm
We are happy to provide further models to suit your requirements. For example, we could cater for a different length, an aluminium pole, a
pole with a spigot diameter of 60mm, a version with a base plate, powder coating in RAL or DB colours or wet coating, epoxy resin coating
/ bitumen in the ground section or shrink-fitting of a PE sleeve.
51
Vulkan Accessories and wall brackets
SHRINK-FIT CORROSION PROTECTION SLEEVES
ACCESSORIES
Suitable for cylindrical and conical poles
Nominal range
Shrink-fit range
Length
CABLE CONNECTION AND JUNCTION BOX WITH SURGE PROTECTION
100
90 - 110
400
115
110 - 130
400
Cable connection and junction box for light pole with surge protection module. Satisfies all mechanical and
electrical requirements and is manufactured in accordance with DIN 43628.
125
125 – 150
400
160
145 – 170
400
170
155 - 180
400
• Optimum mounting thanks to large connection space
•
•
•
•
•
•
•
•
•
•
•
•
Technical data:
• Maximum continuous voltage AC [L-N] (UC) 275 V (50 / 60 Hz)
• Maximum continuous voltage AC [N-PE] (UC) 255 V (50 / 60 Hz)
• Nominal discharge current (8/20 μs) (In) 5 kA
• Max. discharge current (8/20 μs) (Imax) 10 kA
• Total discharge current (8/20 μs) [L+N-PE] (Itotal) 20 kA
EDGE PROTECTION FOR CABLE IN-FEED IN GROUND AREA
Suitable for cylindrical and conical poles.
Dimensions: 150 x 50 mm
Fig. of edge protection for cable in-feed
BASE PLATES FOR CONICAL AND CYLINDRICAL POLES
Elektro-Bauelemente GmbH
An der Wethmarheide 17
D-44536 Lünen
Postfach 1380
D-44503 Lünen
fon: +49 (0) 2306 923-3
fax: +49 (0) 2306 2920
e-mail: info@ebg-luenen.de
internet: www.ebg-luenen.de
Kabelanschluss- und
Übergangskasten Typ: LAK 75
für Lichtmaste
Other versions with other specifications and modules available on request.
CABLE CONNECTION AND JUNCTION BOX
Kabelanschluss und Übergangskästen für Lichtmaste müssen heutzutage
immer kleiner, sicherer im Sinne von Arbeits- und Funktionssicherheit
und montagefreundlicher werden. Kompakt, sicher und funktionell, das
sind die hervorstechenden Eigenschaften des von EBG entwickelten
Anschlusskastens LAK 75.
Der LAK 75 ist einer der kleinsten Kästen seiner Produktklasse bei
gleichzeitig größtem Anschlussraum und kann in Standardlichtmaste ab
3,0 m Lichtpunkthöhe eingesetzt werden. Er ist lieferbar mit einem oder
zwei Sicherungselementen D 01/E 14 und kann mit Sicherungen bis 16 A
bestückt werden. Eine hohe Arbeitssicherheit wird durch ein ausgeklügeltes
System innerer Abdeckungen realisiert, die nur folgerichtig montiert bzw.
demontiert werden können und somit bei Montagearbeiten einen optimalen
Personenschutz garantieren.
For light pole with compact design as of 3m, manufactured in accordance with DIN VDE 0660-505
and DIN 43628.
Type: LAK 75
Die flexible Innenverdrahtung ermöglicht eine universelle Klemmenbelegung,
die jederzeit verändert werden kann. Die weiterentwickelten Mantelklemmen
sind so groß dimensioniert, dass 3 Kabel 5x16 mm2 sicher und mühelos
klemmbar sind. Eine zusätzliche, einrastbare Zugentlastung ist optional
möglich. Drei Kabeleinführungen mit vorgetrennten, ausbrechbaren
Dichtungselementen ermöglichen eine optimale Anpassung an alle
Kabeldurchmesser und verhindern so das Eindringen von Feuchtigkeit,
Schmutz und Kleingetier.
Fig. of corrosion protection sleeve
All dimensions in mm
Design in accordance with DIN 43628
Clamp connection for 2 cables 2.5-16 mm²
Ingress protection IP 54 / protection rating II
Sturdy housing made from impact-resistant polyamide, solid-coloured, RAL 7035, light grey
Enclosure made from polycarbonate (PC), grey
Equipped with two fuse elements 2 x D01, 6A
With integrated sliding and spring clamping technology
Captive, transparent protection against contact
Suitable for pole installation as of an inner diameter of 90 mm
Can be used with door sizes starting from 80 x 300 mm
Dimensions: L=277 mm, W=80 mm, D=66 mm
Integrated surge voltage module in accordance with EN 61643-11 / IEC 61643-11 type 2 Protection rating II.
6
Available in the following dimensions:
250 x 250 mm
300 x 300 mm
400 x 400 mm
Fig. of base plate
WALL BRACKET WITH FLANGE PLATE
Made out of steel, welded and hot-dip galvanised.
Support:
diam. 60 x 100 mm
Length:
150 mm, 250 mm or 400 mm
Setting angle: 0°, 5°, 10° or 15°
Protection against contact in accordance with VBG 4
Reliable clamp connection for 3 cables 5 x 16 mm²
Ingress protection IP 44 / protection rating II
Base body made from PA plastic, cover made from PC plastic
Cable in-feed for 2 or 3 cables with knock-out seal rings
Equipped with two fuse elements D 01 / E 14
Flexible internal pre-wiring
Separate earthing cable guide without terminal box limitation
Contact module for PE and N output terminal in luminaire output area
2 luminaire outputs with plastic sleeves which can be cut
Fig. of 10° setting
Fig. of 15° setting
Eine Kabelkanalführung für ein eventuell benötigtes Erdungsseil ist
vorhanden. Im Leuchtenabgangsbereich befinden sich 2 Kabeleinführungen
mit schneidbaren Kunststofftüllen.
• Einsetzbar für Lichtmaste ab 3,0 m Lichtpunkthöhe
• Sichere Klemmtechnik für 3 Kabel 5 x 16 mm2
• Schutzart IP 44
• Schutzklasse II
• Berührungsschutz gemäß VBG 4
• Grundkörper aus Kunststoff PA, Deckel aus Kunststoff PC
• Kabeleinführung für 2 bzw. 3 Kabel mit ausbrechbaren Dichtungsringen
• Wahlweise Ausstattung mit einem oder
UNIVERSAL BRACKET FOR WALL AND CORNER MOUNTING
Made out of steel, welded and hot-dip galvanised.
zwei Sicherungselementen D 01 / E 14
• Flexible Innenvorverdrahtung
• Großer Anschlussraum für vereinfachte Montage
• Zusätzliche Zugentlastung kann als Rastmodul problemlos
Änderungen vorbehalten / Stand 07/07
•
•
•
•
•
•
•
•
•
•
Fig. of 5° setting
nachgerüstet werden
• Separate Erdungsseilführung ohne Klemmraumeinschränkung
• Kontaktmodul für PE- und N- Abgangsklemmung
im Leuchtenabgangsbereich
• 2 Leuchtenabgänge mit schneidfähigen Kunststofftüllen
• Passendes Erdseil- und Zubehörangebot
Support:
Length:
Setting angle:
diam. 60 x 100 mm
300 mm or 500 mm
15°
Fig. of corner
mounting, view
from above
Fig. of wall mounting, view from
above
53
Vulkan
Pole top mountings and brackets
POLE TOP MOUNTINGS
INDIVIDUAL AND MULTIPLE POLE TOP MOUNTINGS
Made out of steel, welded and hot-dip galvanised.
Pole top moun-
Pole spigot
Support
Projection
Angle
single
diam. 76
diam. 60x100
250
15°
single
diam. 76
diam. 60x100
500
15°
double
diam. 76
diam. 60x100
250
15°
double
diam. 76
diam. 60x100
500
15°
triple
diam. 76
diam. 60x100
250
15°
ting
triple
diam. 76
diam. 60x100
500
15°
quadruple
diam. 76
diam. 60x100
250
15°
quadruple
diam. 89
diam. 60x100
250
15°
quadruple
diam. 76
diam. 60x100
500
15°
quadruple
diam. 89
diam. 60x100
500
15°
All dimensions in mm
V3456 with multiple top mounting
POLE TOP MOUNTINGS WITH VERTICAL SUPPORT
Made out of steel, welded and hot-dip galvanised.
Pole top mounFig. of pole top mounting, single
Pole spigot
Support
Projection
Angle
double
diam. 76
diam. 60x100
200
0°
double
diam. 76
diam. 60x100
250
0°
double
diam. 76
diam. 60x100
400
0°
ting
Fig. of pole top mounting, double
All dimensions in mm
Fig. of pole top mounting, triple
Fig. of pole top mounting, quadruple
V3630 with pole top mounting, triple
Fig. of pole top mounting, double
Other brackets and top mountings with other pole spigots, projections, setting angles and special shapes or colours are available on request.
55
Vulkan Curved pole brackets
CURVED POLE BRACKETS
V1 CURVED POLE TOP MOUNTING BRACKET
Made out of steel, welded, hot-dip galvanised and finished as requested by
the customer to match the luminaire colour.
Connection to luminaire
WESTERBURG-MN CURVED POLE TOP MOUNTING BRACKET
Made out of steel, welded, hot-dip galvanised and finished as requested
by the customer to match the luminaire colour.
Connection to luminaire
Curved bracket radius
Pole spigot
VPS
R260
diam. 76
VPS
R360
diam. 76
I-1/2
R260
diam. 76
E-3/4
R260
diam. 76
VPS
R260
diam. 76
VPS
R360
diam. 76
I-1/2
R260
diam. 76
E-3/4
R260
diam. 76
VPS
R260
diam. 76
VPS
R360
diam. 76
I-1/2
R260
diam. 76
E-3/4
R260
diam. 76
R260
diam. 76
E-3/4
R260
diam. 76
Curved bracket radius
Pole spigot
VPS
R260
diam. 76
VPS
R360
diam. 76
I-1/2
R260
diam. 76
E-3/4
R260
diam. 76
V3 CURVED POLE TOP MOUNTING BRACKET
Made out of steel, welded, hot-dip galvanised and finished as requested by
the customer to match the luminaire colour.
Connection to luminaire
Curved bracket radius
Pole spigot
VPS
R260
diam. 76
Made out of steel, welded, hot-dip galvanised and finished as requested
by the customer to match the luminaire colour.
Pole spigot
I-1/2
Connection to luminaire
HÖHN CURVED POLE TOP MOUNTING BRACKET
Curved bracket radius
diam. 76
diam. 76
Fig. of V2 curved pole bracket
Fig. of Westerburg- MF curved pole bracket
Connection to luminaire
R260
R360
Made out of steel, welded, hot-dip galvanised and finished as requested by
the customer to match the luminaire colour.
Made out of steel, welded, hot-dip galvanised and finished as requested
by the customer to match the luminaire colour.
Pole spigot
VPS
VPS
V2 CURVED POLE TOP MOUNTING BRACKETS
WESTERBURG-MF CURVED POLE TOP MOUNTING BRACKET
Curved bracket radius
Pole spigot
Fig. of V1 curved pole bracket
Fig. of Westerburg-MN curved pole bracket
Connection to luminaire
Curved bracket radius
VPS
R280
diam. 76
I-1/2
R260
diam. 76
E-3/4
R260
diam. 76
Fig. of V3 curved pole bracket
VPS I-1/2 E-3/4
Fig. of Höhn curved pole bracket
= Vulkan Patent System
= 1/2 inch internal thread
= 3/4 inch external thread
Other curved top mounting brackets with other pole spigots, curved bracket radii and special shapes or colours
are available on request.
57
Vulkan Heritage poles
WALL BRACKETS FOR HERITAGE LUMINAIRES
HERITAGE POLES
Projects aiming to retain the historic ambience of an old city should include suitable heritage poles, that fit with the historic
townscape. The heritage poles from Vulkan are made from cast aluminium and powder coated in DB 703. A coating colour in
other DB or RAL shades can also be selected. Mounting is very simple and uses an inner core pole made from galvanised steel
pipe, which perfectly links together all the decorative elements. Customers can choose between a foot plate or buried base for
the installation. The luminaires are mounted in groups of one, two or three with a 3/4" thread. Brackets suitable for wall mounting
are available.
Decorative heritage bracket W3000
Made from cast aluminium, with integrated cable guide
for hidden cable routing, finished as requested to match
the luminaire colour.
Fig. of W3000 wall bracket
Heritage brackets W4000 and W5000
Made out of steel, welded, hot-dip galvanised and with integrated cable guide for hidden cable routing. Finished as requested to
match the luminaire colour.
Fig. of W4000 wall bracket
Fig. of heritage pole group 15101 with buried base
Fig. of heritage pole group 15101 for
mounting one luminaire
Fig. of heritage pole group 15101 with base plate
or foundations
Fig. of heritage pole group 15102 for
mounting two luminaires
Fig. of heritage pole group 15103 for
mounting three luminaires
Fig. of W5000 wall bracket
59
Vulkan
Intelligent lighting
PROVIDING LIGHTING WHEN AND WHERE IT IS NEEDED
LRT – LIGHT REGULATION TWIN (2 PHASES)
INTELLIGENT LIGHTING
LIGHT CONTROLLERS
Modern and energy-efficient LED lighting offers huge potential savings over conventional street lighting. Through the use
of electronic components, it also opens up the option of very easily integrating a light controller to save additional energy.
The right controller for your application depends on your requirements and also the prevailing conditions. Intelligent light
controllers in our luminaires make our lighting systems even more efficient. They minimise annual energy consumption and
therefore associated costs too. We are happy to explain the options in more detail.
CLM - CONSTANT LUMEN MANAGEMENT
The luminous flux of all light sources, including LEDs, reduces as they age. The amount by which it reduces
depends on various parameters. However, these days an electronic controller can counteract this reduction to provide
constant luminous flux over the light sources entire life and save even more energy for good measure.
WITHOUT CONSTANT LUMINOUS FLUX
Over the course of an light sources life, its luminous flux falls by say 20% (L80B10),
but the system output remains unchanged. The drop in luminous flux must
be taken into account when planning through use of the lamp luminous flux
maintenance factor (LLWF). This means that from the outset the lighting system
has to be provided with more energy to take account of the drop in luminous flux
and still provide the amount of light needed at the end of its life.
120%
These days, modern LED systems work in such a stable manner that they only
lose a few percent of luminous flux over the course of their lives. The influence of
constant luminous flux is therefore low.
22h
6h
LRA – LIGHT REGULATION AUTARKIC (SELF-SUFFICIENT)
As the name suggests, Light Regulation Autarkic is not dependent on
an external control line. This controller can therefore also be easily integrated
in existing lighting systems. It can be freely programmed in 5 levels with the data
stored directly in the electronic operating unit meaning that no additional
components are needed. The programmed times at which the luminous flux is
reduced are automatically taken from the switch-on and switch-off times. The midway
point between switching on and off is the reference time for the reduction.
If this changes, the reduction times are adapted accordingly, as happens e.g. when
switching between CET summer / winter time.
For integration in external controllers, Vulkan's luminaires can also be supplied with a DALI connection. In addition to the control
function, the other benefit of DALI is that it is a two-way protocol and e.g. errors and lighting hours can also be read out. The
reduction in performance is then of course dependent on the controller used and the options it offers. One of the disadvantages of
these systems is the limited cable lengths which is why the signal converter (controller) is usually located in the pole or luminaire.
Luminous flux
100%
The integrated electronics increase the flux over the illuminant's life and thereby
keep the luminous flux constant. This does increase the system output over the
illuminant's life, but you save energy right from the start because you don't have
to oversize your lighting system.
Luminous flux
DALI
100%
0%
WITH CONSTANT LUMINOUS FLUX
100%
With this controller, the lighting is reduced using a second phase (control phase).
Switching off the control phase, reduces the luminous flux to a predefined value.
70%
There are two versions available: With "LRT70", the luminous flux is reduced to
around 70% (equating to a reduction of roughly one lighting class). With the classic
"LRT", it is reduced to 50% (the familiar half-night setup). The duration and times can be
freely determined by the user and adapted to suit. This controller can be easily
0%
integrated into networks with an existing control phase and in new systems too.
Luminous flux
0%
100 000h
120%
100%
System power
0%
100 000h
61
Vulkan Intelligent lighting
PROVIDING LIGHT WHEN AND WHERE IT IS NEEDED
LIGHT MANAGEMENT
LMS – LIGHT MANAGEMENT SYSTEM
WIRELESS COMMUNICATION
Connections and/or communication are ensured by a wireless mesh network and require
no additional underground control cables. The light controller can therefore also be easily
integrated in existing networks. Given the range, the signal is sent not just to one participant but
several at the same time (the number depends on local circumstances). For example, the signal may
not be interrupted by a separate earth connection. If a participant doesn't
respond, the signal in the wireless network instantly looks for a "way round".
A light management system can of course do much more than simply reduce energy consumption. It's a forward-looking
technology, which can vastly improve the well-being, safety and therefore also the quality of life of citizens. Needs-based and
individual light control, monitoring, error messages and logging simplify administration and maintenance of lighting systems.
This also involves linking the lighting with other systems or integrating external signals.
SMART CITY
"SmartCity" is synonymous with all-encompassing development concepts, networking of various systems and collecting data to
optimise urban spaces. Lighting and its light management systems, forms part of the SmartCity approach.
AN OVERVIEW OF LIGHTING
The light management system is based on a software, which can control all the lighting in a city. The individual light points
are clearly represented on a map and can be read out or adapted individually or in groups at any time. The lighting hours and
consumption levels are logged and can be exported and documented as reports. The system detects errors and generates
appropriate error messages. Managing the software on a central server also spares the operator from network updates and an
elaborate IT infrastructure. The 128-bit encryption and an additional password protect the network from access by third parties.
See practical example on p.11
PROVIDING LIGHT WHEN AND WHERE IT IS NEEDED
Integrating sensors helps to optimise the lighting without having to compromise on convenience or safety. For example,
integrated motion sensors can be used to minimise illumination. If one of these sensors detects movement from say a pedestrian,
cyclist or car driver, the illumination level is increased to a defined value. At the same time, the command to do the same is sent
to previously defined adjoining luminaires to ensure even lighting in the streets. Another option is to integrate external sensors,
such as twilight switches, clocks, weather sensors, induction loops or traffic systems. These adapt the lighting even better to the
changing conditions.
Modern light management systems are indeed formed from these many different options and great flexibility.
We are happy to advise you on your SmartCity solution.
63
ADDITIONAL
INFORMATION
65
LIST OF ABBREVIATIONS
LUMINAIRES
1 LED module
ALK
Aluminium pole, conical
2x
2 LED modules
STK
Steel pole, conical
30W
System output per LED module
ALZ
Aluminium pole, cylindrical
730
Ra> 70 ; 3000K
STZ
Steel pole, cylindrical
740
Ra> 70;
4000K
STZ 2F
Steel pole, cylindrical, double bracket
750
Ra> 70;
5000K
STK-P
Steel pole, conical, whip shape (whip pole)
I
Protection rating I
3000
Pole height above the ground 3 m
II
Protection rating II
60
Pole diameter 60 mm
III
Protection rating III
76
Pole diameter 76 mm
CLM
Constant Lumen Management
E-3/4
Outer diameter 3/4"
LRT
Light Regulation Twin – reduction to around 50%
(default)
3.0
Wall thickness 3 mm
E700
Length of buried base in ground 0.7 m
LRT70
Light Regulation Twin – reduction to around 70%
MB-T1
Straight bracket, pole top, single
LRA1
Light Regulation Autarkic, scene 1
MB-T2
Straight bracket, pole top, double
LRA2
Light Regulation Autarkic, scene 2
MB-S1
Straight bracket, side entry, single
LRA3
Light Regulation Autarkic, scene 3
MB-S2
Straight bracket, side entry, double
LRAC
Light Regulation Autarkic, customised (option)
MB-S3
Straight bracket, side entry, triple
LMS
Light Management System
MB-S4
Straight bracket, side entry, quadruple
DALI
DALI for external controllers (default = DALI
logarithmic)
MB-B1
Curved bracket, single
O1
Optics for major thoroughfares
MB-B2
Curved bracket, double
O2
Optics for thoroughfares
MB-O
Round/circular bracket, single
O3
Optics for residential streets
WB-S1
Wall bracket, single
O4
Optics for cycle paths and walkways
60x100
Support diameter x support length in mm
I-1/2-BE
Internal thread, diameter, curved bracket end
E-1/2-BE
External thread, diameter, curved bracket end
VPS
Vulkan Patent System
VPS-IB
Vulkan Patent System, in curved bracket
L1000
Length of bracket
L1000-5°
Length of bracket, 5° inclination
R260
Radius of curved bracket
HÖ
Höhn
WB-MF
Westerburg, far-off pole
WB-MN
Westerburg, nearby pole
V1
Curved bracket, version 1
V2
Curved bracket, version 2
V3
Curved bracket, version 3
O5
Optics for open spaces
O6
Optics for pedestrian crossings, beam to the right
O7
Optics for main streets and side streets, S classes
(previously also along with QVS, QVM, QEM)
O8
Symmetrical optics, all-round
O9
Optics, linear distribution
HS
House-side shield
O1X
Catenary luminaires: If the luminaire is arranged across
the street, the optics designation has an "X" tagged on
the end, e.g. O1X, O3X, O7X, ...
Catenary luminaires: If the luminaire is arranged along
the street, the optics designation has an "L" tagged on
the end, e.g. O1L, O3L, O7L, ...
Protection rating I
The CE symbol is used by the manufacturer and confirms that he is
responsible for the products' conformity with the relevant EC and/or
EU laws. Our products have to comply with the Low Voltage Directive
and the EMC Directive 2004/108/EC (interference resistance, emitted
interference) in order to use the CE symbol.
POLES AND BRACKETS
1x
O1L
LIST OF SYMBOLS
Protection rating II
The ENEC symbol is the European symbol proving that luminaires
comply with European safety standards. The test method is described
in the European 60598-1 standard. The ENEC symbol is used along
with the identification number of a European test centre (VDE = 10).
It documents the fact that the luminaires have been constructed and
tested "in compliance with applicable standards", see Low Voltage
Directive 2006/95/EC.
Protection rating III
Five-year guarantee
IP (INGRESS PROTECTION)
The IP is identified using 2 parameters:
Parameter 1: Level of protection against contact and foreign bodies
First pa-
Protection against foreign bodies
rameter
Protection against contact
0
No protection
No protection
1
Protected against solid foreign bodies with a diameter of 50 mm or more
Protected against access with the back of the hand
2
Protected against solid foreign bodies with a diameter of 12.5 mm or more Protected against access with a finger
3
Protected against solid foreign bodies with a diameter of 2.5 mm or more
Protected against access with a tool
4
Protected against solid foreign bodies with a diameter of 1.0 mm or more
Protected against access with a wire
5
Dust-protected
Complete protection against contact
6
Dust-tight
Complete protection against contact
Parameter 2: Levels of protection for water protection
Second
Protection against water
parameter
0
No protection
1
Protection against drips
2
Protection against falling drips if the housing is tilted up to 15°
3
Protection against falling spray up to 60° from the vertical
4
Protection against splashes from all sides
7035
RAL 7035 - light grey
703
DB 703 - iron mica, dark grey DB colour
5
Protection against jets of water (nozzle) from any angle
703SP
DB 703 + seawater protective finish (add to colour code
without space)
SP = salt protection or seawater protection
6
Protection against powerful jets of water
7
Protection against brief immersion
8
Protection against permanent immersion
9
Protection against water during high-pressure/steam jet cleaning, especially in agriculture
67
Vulkan Guarantee
f ) The product was not exposed to ambient temperatures exceeding the
value of Ta = 45°C (integrity, safety temperature). If a lower nominal ambient
temperature is stated in the data sheet for the product, depending on the
rated power currently being used, this nominal ambient temperature must not
be exceeded when the product is used
GUARANTEE
Guarantee conditions for LED luminaires for the "Vulkan" brand
In general
Nordeon GmbH (hereinafter referred to as "Nordeon-Vulkan") as
manufacturer of LED lights of the "Vulkan" brand assumes a guarantee
within the framework of the following terms of guarantee. These terms
of guarantee shall exclusively apply for the LED lights mentioned in
section A and only towards the customers also specified in section A.
Any performance arising from the guarantee shall apply in addition to
the statutory warranty claims for defects, product liability claims and
other statutory claims.
Scope of application
The guarantee described below is granted by Nordeon-Vulkan for the
LED lights for lighting the urban space of the brand Vulkan which are
distributed in the European Union and Switzerland (hereinafter referred
to as "products") to the customers of the company. Any customer
who has any claims arising from this guarantee shall be the direct
contractual partner of Nordeon-Vulkan only (hereinafter referred to as
"customer(s)").
This guarantee refers to the purchase of products as of the effective date
of this guarantee specified below.
Any LED delivered for retrofitting lights (so-called "LED retrofit kits"),
used LED lights, completely overhauled LED lights which are not
intended for sale but for exhibition purposes shall be excluded from the
guarantee.
Exceptions to this are original LED replacement inserts which are
also used in the original Nordeon-Vulkan products and have the
corresponding CE certification and type plate relating to the "Vulkan"
brand light type.
Scope
In its relationship with the customer, Nordeon-Vulkan guarantees
that from the invoice date all products are free from defects relating
to function, material, and workmanship which (a) either reduce the
rated output and rated luminous flux specified in the data sheet by
at least [20%] or (b) otherwise substantially affect the functioning of
the products for a period of FIVE (5) years (hereinafter referred to as
"guarantee period") in accordance with the following conditions and
restrictions (in the following referred to as: "case of guarantee").
Compliance with these performance values requires that the maximum
ambient temperature at night (ta max) does not exceed the maximum
nominal value; however, for the nominal current of the operator
a tolerance of 5% is taken into consideration. The data sheets are
published on the website of Nordeon-Vulkan or, upon request, they will
be sent to the customer.
This guarantee is granted for products which are switched on and off
every day, the annual operating hours of which are 4000-5000 hours,
and which are used in accordance with the technical specifications and
installation instructions. Any official photometric measurements shall
be carried out by Nordeon alone or, insofar as the customer objects to
the result obtained by Nordeon-Vulkan, by a mutually agreed accredited
inspection body with a protocol specified by Nordeon.
Guarantee service
If a product has a problem which is considered a case of guarantee
according to these terms of guarantee, Nordeon-Vulkan shall repair or
replace the returned product at its own discretion within the framework
of the guarantee. If the product is no longer manufactured or not
available for any other reason, Nordeon-Vulkan may offer an alternative
product that is comparable to the objected product.
Further claims within the framework of this guarantee, in particular
claims for damages, shall be excluded.
Exceptions and restrictions
This guarantee is exclusively limited to the guarantee service that is
finally regulated in section C for the products delivered by NordeonVulkan. Additional costs, e.g. costs for the dispatch of defective parts or
products, the disassembly, reassembly, transport time, lifting platforms
and scaffolding or other costs caused by failure of the installation and/
or costs in connection with any consequential, special or incidental
damage or mere financial damage, such as e.g. lost earnings/profits,
property damage, strike, unused assets, production losses, costs for
road closures, traffic signs, detours, etc., shall not be covered by this
guarantee.
Furthermore, Nordeon-Vulkan shall not be liable on the basis of this
guarantee for compensation of persons for such losses or personal
injury of damage to property. Consequently, Nordeon-Vulkan is not
liable for claims for damages due to failure of performance or for any
consequential damage.
The customer must demonstrate that the errors, defects or any damage
to the product or parts thereof are not a direct or indirect result of
negligence, misuse, abuse, or misappropriation by the customer and
that in particular the following conditions and requirements have been
fulfilled without restriction:
a) The customer transported the product properly and in the original
packaging
b) The customer stored, installed, used and maintained the product
in accordance with the specifications, guidelines, and instructions of
Nordeon-Vulkan and with the IEC standards, if applicable
c) The product was used for one of the purposes intended by NordeonVulkan
d) The product was wired, installed and operated within the framework
of the electrical values, the operating range and the environmental
conditions in accordance with the specifications of Nordeon-Vulkan,
the operating instructions, the IEC standards, in accordance with the
European Directives or other documents attached to the products
e) The product was not exposed to any mechanical load that is not
compatible with the intended purpose
g) The product and/or parts thereof were not repaired, replaced, adjusted
or changed by the customer or any other person without the prior written
consent of Nordeon-Vulkan
h) The parts of the product which are not accessible/sealed, e.g. LED units,
were not opened by the customer without the prior written consent of
Nordeon-Vulkan
i) The product was not handled improperly and/or brought into contact with
chemicals
j) The product was continuously operated at the same place where the
product was initially installed.
The terms of guarantee of Nordeon-Vulkan shall not apply for:
a) Any damage or non-compliance due to force majeure or the violation
of applicable standards or regulations, including but not limited to those
contained in the latest safety, industry, and/or electrical standards and in the
regulations that apply to the customer
b) Any non-compliance, construction errors or malfunctions if NordeonVulkan adhered fully to the written descriptions, drawings or specifications
of the customer and it becomes apparent later on that they were unsuitable,
incomplete or incorrect
c) Nordeon-Vulkan shall not be responsible for the power supply conditions,
including voltage peaks, over-/undervoltage and ripple current control
systems which exceed the indicated restrictions of the product and the
respective supplier or which do not comply with the customary industry
standards for acceptable input power
d) Force of nature, such as lightning damage or corrosion if the corrosion
results from external causes or factors (e.g. chemicals)
e) Failure of less than ten percent (10%) of all LEDs (rounded up to the next
unit) in a product
f ) Additional control units, e.g. telemanagement
g) Parts, elements and/or accessories which were added to the product after
delivery
The guarantee requires the invoice to be paid by the due date and send a
description of the possible case of guarantee to the address mentioned above
at the latest within thirty (30) days after determination of the possible case
of guarantee and in any case within the guarantee period. In this written
assertion of the possible case of guarantee, the customer shall provide the
following information:
•
Job and invoice number
•
Installation characteristics (place, street, number of products concerned,
relevant installation details)
•
Circumstances and environmental conditions in which the products were
used
•
Name, model and number of allegedly defective products
•
Copy of invoice and delivery note
•
Date of installation
•
Detailed description of the problem.
•
Additionally, the customer must be indicated as receiver in the original
invoice or the delivery note
2) The documents mentioned in section F, number 1 shall be addressed to:
Nordeon GmbH
Geschäftsbereich Vulkan
QM Abteilung
Rathenaustraße 2-6
3132 Springe
3) After submission of the documents mentioned in number 2, NordeonVulkan will assign a QM number (hereinafter referred to as "QM notice") in
order to be able to allocate the claim accordingly.
After notification of the QM number, the customer must send the product
concerned to the address specified in the QM notice at his own expense.
4) Potentially defective products will become property of Nordeon-Vulkan as
soon as they are replaced.
5) Should Nordeon-Vulkan determine after issuance of a QM number that
the product or the products of the customer which were sent under this QM
number are not covered by the guarantee, Nordeon-Vulkan shall be entitled to
charge the customer for the costs arising from the examination of this product
or these products regarding a claim under guarantee.
6) For parts or products which were replaced or repaired during the guarantee
period, a guarantee for the remainder of the original guarantee period of
these parts or products shall apply, if any.
7) All measures shall be taken with the exclusion of goodwill and warranty
claims.
h) Normal wear of the product
Final provisions
If the product is installed in a corrosive environment, in particular by the sea
or in another place with chemical contamination, the customer must inform
Nordeon-Vulkan about this before conclusion of the contract. Nordeon-Vulkan
will then give instructions concerning the necessary measures to be followed
by the customer (e.g. special treatment, varnishing, etc.). This shall also apply
for the regular performance of the provided maintenance activities for the
duration of the operating period.
1) German law shall apply exclusively to the legal relationship in connection
with the guarantee excluding the UN Convention on Contracts for the
International Sale of Goods. Exclusive jurisdiction shall be Springe.
No implied or other guarantees
1) This guarantee does not contain a guarantee that the products are suitable
for a specific purpose or that the violation of rights of a third party is excluded.
2) No representative, dealer or seller shall be entitled to change, restrict or
extend these terms of guarantee on behalf of Nordeon-Vulkan.
Claims for guarantee services
The guarantee requires the invoice to be paid by the due date. The customer
must immediately inform Nordeon-Vulkan about any possible claim under the
guarantee and
2) The invalidity of individual provisions of these guarantee commitments shall
not affect the validity of the remaining provisions.
Effective date: May 2016
69
Vulkan Vulkan
Nordeon Group
VULKAN: LIGHTING UP
OUTDOOR SPACES
Vulkan was founded in 1898 and is therefore one of the
experienced companies in the lighting industry anywhere
in the world. The company has always enjoyed a good
reputation. Today Vulkan is one of the leading brands
for lighting outdoor spaces in Germany, France and the
Netherlands. It also has a strong international presence.
NORDEON GROUP
Over 1000 employees the world over are standing by to assist you. Whether you are an architect,
light designer, builder, installer or end user – our experienced staff will cater to your individual needs. We
combine high-quality light and control technology with ultra-modern, first-class design and quality, made in
Europe and the USA.
Before
ARCHITECTURAL LIGHT
Vulkan designs, develops and produces luminaires –
especially for cities and communities. The products are
synonymous with maximum efficiency, versatility and
durability.
ne of the world's leading manufacturers of
O
outdoor architectural lighting
S taging of architectonic buildings and
infrastructures using spectacular lighting
effects and the limitless diversity of dynamic
light sources.
The company's product range covers all outdoor and
community areas, such as streets, squares, traffic junctions,
danger spots, pedestrian areas and public buildings and
meets the toughest of requirements.
igh-quality and
H
decorative
outdoor lighting and site
furnishings
olistic concepts
H
for the design of urban
spaces
Made possible through use of the most
innovative and alternative solutions and
thanks to a complete state-of-the-art range
of modular and linear spotlights which can
be mounted on surfaces, integrated and used
underwater. Visual display solutions coupled
with ultra-modern digital control systems
are also available. Proven quality, absolute
reliability and highly competitive.
After
Germany,
Wunstorf
Germany, Wuppertal
Vulkan luminaires are renowned for their high standards of technical
functionality and maximum energy efficiency. This is achieved through
the use of state-of-the-art LED and control technology.
Vulkan has more than 115 years of experience, giving it an invaluable
edge when it comes to understanding customer's precise requirements.
This is reflected in product design, adaptation of technology and high
levels of customer support.
Our technically advanced, German-made products, sold at competitive
prices, coupled with high energy efficiency and long maintenance
intervals ensures short and therefore attractive payback times for
customers.
Vulkan . A member of the Nordeon Group
www.vulkan.eu
OUTDOOR LIGHTING
INDOOR LIGHTING
igh-tech outdoor
H
lighting
ighly efficient with
H
short payback times
I nnovative light control
systems for greater
security and
reduced overall
operating costs
Award-winning design solutions
for indoor areas, e.g. for offices,
hospitals, universities and sales
rooms
Great expertise in improving the
visual environment in buildings
through individual solutions
Product design based on multi-functional "multi-purpose
components", which enable a
large range of custom-made and
project-specific solutions while
satisfying high quality standards
I ndoor lighting for retail and
industry
igh-quality and cost-effective
H
fluorescent lamps and
fluorescent lamps for special
applications
ighly efficient LED lights and
H
light management solutions with
short payback times
ustom-made LED
C
solutions, for OEM too
About the company
A proven track record
The Nordeon Group is made up of mid-sized compa-
The Nordeon Group was founded in 2012 by the current Dutch owner
nies from the lighting industry, which work closely with
Varova and the Nordeon brand was launched in Germany, France and
their specific markets while at the same time benefiting
the Netherlands. Nordeon has bases at Springe in Germany and Cha-
from the group's worldwide support and technologi-
lon-sur-Saône in France and has specialised in the development, design
cal infrastructure. At present, the lighting industry is
and production of lighting solutions, such as light line systems, high bay
undergoing some major changes. Demand for energy
luminaires and downlights for industry and retail. In 2013 the Nordeon
efficiency is growing all the time, and the development
Group acquired Vulkan and Hess, adding to the group two well-known
of efficient LED lights and appropriate technology is
companies specialising in urban and decorative outdoor lighting. The out-
taking giant steps forward. The Nordeon Group com-
door element was further expanded through the acquisition of the Italian
bines the strength of a large group of companies with
company Griven, a leading specialist in architectural light. And last but not
the benefits of flexible, independently operating firms
least, in 2016 the German premium indoor lighting company, WILA, joined
and is therefore ideally positioned to drive forward this
the Nordeon Group. The group is committed to investing in the research
change.
and development of ultra-modern lighting technology solutions to further
develop its range of world-leading lighting brands and thereby adapt it to
Flexibility & quality – made in Europa & USA. We
the ever-changing requirements of the lighting market. Our team of over
are firm believers in developing and manufacturing
1000 members of staff ensures the delivery of high-quality lighting pro-
products in close proximity to our customers. This
ducts, first-class design and superlative quality standards. With production,
allows us to offer the flexibility and quality but also the
development, a certified laboratory, light design, customer service and a
service that our customers want. Through well thought-
sales and marketing service spanning all of Europe and the USA and an
out investments in product and production technology,
unrivalled range of brands and products, the Nordeon Group is set up to
we have proven that we are able to supply the best
support its customers – no matter where they are based and no matter
products. All our products are "made in Europe and the
what challenges they face.
USA".
71
Vulkan Griven Hess
GRIVEN: BRINGING BUILDINGS
TO LIFE
HESS: SHAPING PUBLIC
SPACES
Founded in 1990, GRIVEN from Castel Goffredo, Italy, has
established itself as one of the world's leading manufacturers in
the architectural lighting market. The company has an extensive
product range offering proven quality, good reliability and totally
weatherproofed luminaires, which guarantee industry professionals
the most innovative and alternative solutions.
Hess is Germany's leading brand for designed and
architectonic outdoor lighting. The company's
wide range of products ensures availability of
the best products and light solutions for every
application. It caters for public spaces, industry
and administration. Premium furnishings for
streets and squares rounds off the lighting
range. Through the perfect combination of
luminaires and site furnishings, Hess designs and
embellishes public spaces.
A complete range including popular colour changers, sky trackers
and a full range of products for theatres are available the world
over through a carefully selected network of specialist dealers.
Through its attempts to remain at the forefront of an ever-changing
and growing market, in 2001 GRIVEN picked up on the trend for
LED technology. This gave GRIVEN the edge over its competitors
and it was the first company to offer a full range of LED products
for architectonic use. These professional LED lighting solutions
combine the latest, most energy efficient semi-conductor
technology and offer high-quality equipment for a wide range of
areas of application.
Hess has its headquarters in VillingenSchwenningen, southern Germany. To support its
US customers, it has a strong production, support
and trade base in Gaffney, South Carolina.
Hess . A member of the Nordeon Group
www.hess.eu
Hess was one of the first companies in this sector
to integrate LED technology in product design
and development. As a result, it is at the very
forefront of the light design and control sector.
Hess has made a name for itself through its
unmistakeable style elements, the use of very
high-quality materials, its attention to detail and
unsurpassed quality standards. The brand has
won the praise of architects and designers all
over the globe.
South Korea,
the Incheon Bridge
Egypt, the Citadel
A range of cutting-edge projectors – for surface mounting,
modular, linear, for integration, under water and for visualisations
– can enrich the most ambitious of light shows with spectacular
effects and a boundless range of different dynamic and
environmentally-sound light sources.
Innovation and sustainability have always been core values to
GRIVEN. Today sustainability and efficiency are the new technical
guidelines for products, which the company is proud to produce
in Italy and are the result of high standards in construction and
design.
Griven . A member of the Nordeon Group
www.griven.com
UK, Beaufort
USA, Kissimmee
Lakefront Park
73
Vulkan Nordeon WILA
NORDEON: LUMINAIRES
FOR INDUSTRY AND RETAIL
WILA: LIGHT AS AN ELEMENT
OF ARCHITECTURE
Nordeon has two of the largest, most advanced
and most dedicated production sites for LED
lights in Europe at Springe in Germany and at
Chalon-sur-Saône in France.
have meant that Nordeon is a leader in the
development, design and manufacture of highperformance luminaires and lighting solutions for
industry and retail.
All the workshops, the ESD-protected production
facilities, the modern equipment for quality
controls and testing, the very experienced staff
and production following the LEAN principle
Nordeon . A member of the Nordeon Group
www.nordeon.com
WILA is a leading specialist in individual light.
Individual light enriches and inspires but often
involves high levels of complexity. To master this,
WILA collaborates closely with all the professions
involved in developing a building and planning
its lighting in order to advise, understand and
develop – with the overall objective of improving
the visual environment.
WILA . A member of the Nordeon Group
www.wila.com
Ireland, Airport Dublin,
Terminal 2
WILA is synonymous with excellent service,
superlative and durable quality and technologyand application-based and therefore customerfocused innovations. Such standards require a
solid organisation. In order to quickly and reliably
cater for your requirements, WILA has its own
design and development department and a team
of specialists to implement customised special
luminaires.
Netherlands,
Sissy-Boy
Very high standards are set for component
production and final luminaire assembly –
especially for LEDs. To meet these standards,
WILA has its own lab, operated in line with
international standards, for photometric and
thermotechnical measurements. WILA operates
at 3 sites, employs over 150 members of staff and
has partners in over 30 countries.
Netherlands,
Petrol Industries
Germany, Berlin. DRIVE. Volkswagen Group
Nordeon GmbH
Rathenaustraße 2-6
31832 Springe, Germany
Tel. : +49 (0) 5041 - 75 100
The data used in this publication is without obligation and may change as a result of technical developments.
Copyright for pictures: Vulkan; image on p.15: Dr. Holger Fuchs
Vulkan . A member of the Nordeon Group
Art.no.: 100031
sales@vulkan.eu
www.vulkan.eu
OUTDOOR
Download