Chambers
Accessories
Equipment 1
Equipment 2
Amplifiers
Antennas
BROADBAND
RF-POWER-AMPLIFIERS
10 kHz - 6 GHz
For immunity tests according to IEC, EN, ISO, SAE, MIL
Power amplifiers with high linearity and high amplification in a
wide frequency range with thermal and over current protection.
Possible signal input formats are: CW / AM / PM / FM / PULSE
Broadband RF-power amplifiers
Special features
The broadband RF - power
amplifiers are optimized to have
high efficiency, high 1dB
compression and high gain
FRANKONIA RF-power amplifiers
supply high linearity in a wide
frequency range and a high
amplification
Possible signal input formats:
CW / AM / PM / FM / Pulse
Low noise and distortion
Large variety of amplifier types
for the whole EMC relevant
frequency range
Bulk current injection (BCI)
applications at our FLC line
Internal forced air cooling together
with internal protection circuits,
protect the amplifiers against
damage caused by overtemperature (e.g. high room temperature).
The occurrence of a fault is
shown by a lit indication lamp
at the front panel (FAULT)
The amplifiers can be switched
into stand-by mode for safety
reasons (e.g. via a door contact
relay switch located at an
anechoic chamber)
The amplifiers are constructed in
19” technology
PAGE // 2
GPIB interface and integrated
forward / reverse power measurement available as option
Mode of operation
RF power amplifiers are used to take a low input signal and convert it into a larger
output signal that is sufficient high to reach the required test level.
Application areas
FRANKONIA produces RF-power amplifiers whose frequency range and output power
have been tailored especially to the applications in EMC immunity test systems according
to IEC 61000-4-3 / EN 61000-4-3 and IEC 61000-4-6/ EN 61000-4-6 or other similar
national and international regulations (ISO, SAE, MIL, ETSI, ...).
Frequency range
Depending on the model the amplifiers are available up to a nominal power of 5000 W
in a frequency range from 10 kHz to 6 GHz with an operation mode of A/AB.
Add following ordering option
at the end of the part number
Description
R or (without mark)
Rear panel connectors (standard)
F
Front panel connectors
E
Control option (GPIB, RS 232, LAN)
Our amplifiers FLL-25 , FLL-75, FLC-100E, FLC-150 and FLC-150E basically have
front panel connectors without any other options.
10 kHz - 300 MHz
Part number
FLL-25A
FLL-25
FLL-75
Frequency range (Hz)
10k-230M
100k-250M
Max. output power typ. (W)
25
Output power @ 1dB compression,
typ. min. (W)
FLL-100A
FLL-250A
FLL-600A
100k-300M 150k-230M
10k-250M
10k-200M
10k-200M
25
75
75
100
250
600
15
20
50
45
60
175
400
RF input, max. (dBm)
0
0
0
0
0
0
0
Gain (dB), typ.
+44
46
51
+49
+50
+55
+59
Flatness (dB), typ.
±1.5
±1.5
±1.5
±1.5
±2.5
±2
±2.5
IP3 (dBm), typ.
+48
48
52
+52
+54
+60
+60
Input VSWR, max.
2:1
1.5:1
1.5:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-15 @ 15W
-20 @ 20W
-20 @ 50W
-15 @ 45W
-15 @ 60W
-15 @ 175W
-15 @ 250W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 15W
-75 @ 20W
-75 @ 50W
<-60 @ 45W
<-60 @ 60W
<-60 @ 175W
<-60 @ 250W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
449 (19”)
449 (19”)
483 (19")
483 (19")
483 (19")
483 (19")
H
134
133
133
134
223
223
356
D
508
436
436
508
508
508
661
Weight (kg)
16
8
10
22
34
36
68
AC power input (W)
200
150
400
400
600
1200
4000
Power supply (VAC)
100-240
88-264
100-240
100-240
100-240
100-240
180-240
Phases
1
1
1
1
1
1
1
Operating humidity
Non-condensing (%)
95
95
95
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
FLL-75A
• VSWR protection
Specifications at 25°C | Specifications subject to change without notice
3 // PAGE
10 kHz - 400 MHz
Part number
FLC-75
FLC-100
FLC-100E
FLC-150
FLC-150E
Frequency range (Hz)
100k-400M
100k-400M
10k-400M
100k-400M
10k-400M
Max. output power typ. (W)
75
140
130
220
180
Output power @ 1dB compression,
typ. min. (W)
50
80
70
140
125
RF input, max. (dBm)
0
0
0
0
0
Gain (dB), typ.
51
51
51
53
53
Flatness (dB), typ.
±1.5
±1.5
±1.5
±1.5
±1.5
IP3 (dBm), typ.
52
58
57
61
60
Input VSWR, max.
1.5:1
1.5:1
2:1
2:1
2:1
Harmonics (dBc), typ.
-20
-20
-20
-20
-20
Spurious signals (dBc), typ.
-75
-60
-60
-60
-60
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19”)
483 (19”)
483 (19”)
483 (19”)
H
133
150
150
150
150
D
436
455
455
455
455
Weight (kg)
10
16
16
20
20
AC power input (W)
400
500
500
900
900
Power supply (VAC)
88-264
230
230
230
230
Phases
1
1
1
1
1
Operating temperature (°C)
0-45
0-45
0-45
0-45
0-45
Operating humidity
Non-condensing (%)
95
95
95
95
95
Cooling
Internal forced air Internal forced air Internal forced air Internal forced air Internal forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
PAGE // 4
Specifications at 25°C | Specifications subject to change without notice
1 MHz – 1000 MHz
Part number
FLH-4A
FLH-50A
FLH-100A
FLH-100C
FLH-200C
Frequency range (Hz)
1M-1000M
1M-1000M
1M-1000M
20M-500M
20M-500M
Max. output power typ. (W)
4
50
100
100
200
Output power @ 1dB compression,
typ. min. (W)
2
30
60
60
120
RF input, max. (dBm)
0
0
0
0
0
Gain (dB), typ.
+36
+48
+50
+51
+54
Flatness (dB), typ.
±1.5
±2
±2.5
±2
±2
IP3 (dBm), typ.
+39
+51
+54
+56
+55
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 2W
-20 @ 30W
-20 @ 60W
-20 @ 60W
-20 @ 120W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 2W
<-60 @30W
<-60 @60W
<-60 @ 60W
>-60 @ 120W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
H
134
134
223
89
223
D
508
508
508
458
508
Weight (kg)
20
23
37
16
37
AC power input (W)
100
750
2500
600
1000
Power supply (VAC)
100-240
100-240
200-240
100-240
100-240
Phases
1
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
95
Cooling
Internal forced air Internal forced air Internal forced air Internal forced air Internal forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
Specifications at 25°C | Specifications subject to change without notice
5 // PAGE
20 MHz - 1000 MHz
Part number
FLH-20B
FLH-70B
FLH-120B
FLH-200B
FLH-500B
Frequency range (Hz)
20M-1000M
20M-1000M
20M-1000M
20M-1000M
20M-1000M
Max. output power typ. (W)
20
70
120
200
500
Output power @ 1dB compression,
typ. min. (W)
13
40
70
120
250
RF input, max. (dBm)
0
0
0
0
0
Gain (dB), typ.
+44
+49
+52
+54
+58
Flatness (dB), typ.
±1.5
±2
±2
±3
±2.0
±1.25 with ALC
IP3 (dBm), typ.
+47
+52
+55
+57
+63
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 10W
-20 @40W
-20 @70W
-20 @120W
-15 @ 250W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 10W
<-60 @40W
<-60 @70W
<-60 @120W
<-60 @ 250W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
788 (31")
H
134
134
178
223
610
D
508
508
508
508
661
Weight (kg)
20
22
28
38
87
AC power input (W)
200
750
1500
3000
5000
Power supply (VAC)
100-240
100-240
100-240
200-240
200-240
Phases
1
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
95
Cooling
Internal forced air Internal forced air Internal forced air Internal forced air Internal forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• VSWR protection
• VSWR protection, etc.
PAGE // 6
Specifications at 25°C | Specifications subject to change without notice
80 MHz - 1000 MHz
Part number
FLH-200B1
FLH-300B1
FLH-500B1
FLH-1000B1
FLH-2000B1
FLH-5000B1
Frequency range (Hz)
80M-1000M
80M-1000M
80M-1000M
80M-1000M
80M-1000M
140M-1000M
Max. output power typ. (W)
200
300
500
1000
2000
5000
Output power @ 1dB compression,
typ. min. (W)
120
200
350
700
1200
-
RF input, max. (dBm)
0
0
0
0
0
+3
Gain (dB), typ.
+54
+56
+58
+68
+71
+67
Flatness (dB), typ.
±2
±3
±3.0
±4
±4
±8
IP3 (dBm), typ.
+59
+62
+64
+64
+64
-
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 120W
-20 @ 200W
-20 @ 350W
-15 @ 700W
-20 @ 1200W -15
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 120W
<-60 @ 200W
<-60 @ 350W
<-60 @ 700W <-60 @ 1200W <-60
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)/7/16(f)
N(f)/7/16(f)
N(f)/7/16(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
788 (31")
788 (31")
1997 (78.6")
H
134
178
223
610
610
562
D
610
610
661
661
661
915
Weight (kg)
28
39
50
125
125
680
AC power input (W)
1800
3000
6000
10000
10000
12000
Power supply (VAC)
180-240
180-240
180-240
240
240
208
Phases
1
1
1
3
3
3
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
5/+40
Operating humidity
Non-condensing (%)
95
95
95
95
95
90
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Liquid cooling
for RF
forced air for
power supply
Circuit protection
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal overload
• Thermal
overload
• Over current
• Over current
• Over current
• Over current
• Over current
• O ver current /
voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• VSWR protection
• R F output
overdrive, etc.
7 // PAGE
Specifications at 25°C | Specifications subject to change without notice
0.8 GHz - 2 GHz
Part number
FLG-7A
FLG-12A
FLG-25A
FLG-50A
Frequency range (Hz)
0.8G-2G
0.8G-2G
0.8G-2G
0.8G-2G
Max. output power typ. (W)
7
12
25
50
Output power @ 1dB compression,
typ. min. (W)
5
10
20
35
RF input, max. (dBm)
+10
+10
+10
+10
Gain (dB), typ.
+39
+41
+44
+48
Flatness (dB), typ.
±1.5
±1.5
±1.5
±1.5
IP3 (dBm), typ.
+47
+50
+53
+56
Input VSWR, max.
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 5W
-20 @ 10W
-20 @ 20W
-20 @ 35W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 5W
<-60 @ 10W
>-60 @ 20W
<-60 @ 35W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
H
89
134
89
134
D
458
508
458
661
Weight (kg)
12
15
12
14
AC power input (W)
100
120
220
400
Power supply (VAC)
100-240
100-240
100-240
100-240
Phases
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Infinite load VSWR
• Over current
• Over voltage
PAGE // 8
Specifications at 25°C | Specifications subject to change without notice
• Over voltage
0.8 GHz - 2 GHz
Part number
FLG-120A
FLG-200A
FLG-300A
FLG-500A
Frequency range (Hz)
0.8G-2G
0.8G-2G
0.8G-2G
0.8G-2G
Max. output power typ. (W)
120
200
300
500
Output power @ 1dB compression,
typ. min. (W)
80
150
150
300
RF input, max. (dBm)
+10
+10
+10
+10
Gain (dB), typ.
+52
+54
+56
+58
Flatness (dB), typ.
±2
±2
±2
±2.5
IP3 (dBm), typ.
+59
+62
+64
+65
Input VSWR, max.
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 80W
-20 @ 150W
-20 @ 250W
-20 @ 300W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 80W
<-60 @ 150W
<-60 @ 300W
<-60 @ 300W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f) 7/16 DIN
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
H
178
223
223
356
D
508
508
674
661
Weight (kg)
28
37
46
68
AC power input (W)
1000
1500
2500
3000
Power supply (VAC)
100-240
100-240
208 + 10%
180-264
Phases
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• VSWR protection
Specifications at 25°C | Specifications subject to change without notice
9 // PAGE
Frankonia amplifier with control option (front view)
GPIB (IEEE)
Stand-by interlock
RF output
Type label with model and
Serial number
Ventilating grating
Rear panel
(grounded through power cable)
PAGE // 10
RF input
Power supply
Power: on / off switch
Display
Control buttons up / down
Carrying handles
Ventilating gratings
Control buttons
(Mode, Standby, ALC, Gain)
Fault LED
Frankonia amplifier with control option (back view)
IEEE-488
FLG 30CA-RE
Model FLG-30C-RE
SN: 1011
SN:
1011
Code: 0614
Code:
0614
100-240 VAC 50/50 Hz
100-240 VAC 50/50 Hz
IEEE-488
11 // PAGE
Code: 0614
SN: 1011
Model FLG 30CA-RE
0.7 GHz - 2.5 GHz
Part number
FLG-13B
FLG-25B
FLG-50B
FLG-100B
Frequency range (Hz)
0.8G-2.5G
0.8G-2.5G
0.8G-2.5G
0.7G-2.5G
Max. output power typ. (W)
13
25
50
100
Output power @ 1dB compression,
typ. min. (W)
10
20
40
80
RF input, max. (dBm)
+10
+10
+10
+10
Gain (dB), typ.
+42
+45
+48
+50
Flatness (dB), typ.
±2
±2
±2
±2
IP3 (dBm), typ.
+50
+53
+56
+58
Input VSWR, max.
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 10W
-20 @ 20W
-20 @ 40W
-20 @ 80W
Spurious signals @ 1 dB comp.,
(dBc), typ.
>-60 @ 10W
<-60 @ 20W
<-60 @ 40W
<-60 @ 80W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
H
89
134
134
134
D
458
508
458
508
Weight (kg)
9
18
20
28
AC power input (W)
100
300
600
1200
Power supply (VAC)
100-240
100-240
100-240
100-240
Phases
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
Cooling
Internal forced air
Internal forced air
Internal forced air
Internal forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
PAGE // 12
Specifications at 25°C | Specifications subject to change without notice
0.7 GHz - 2.5 GHz
20 MHz - 3.0 GHz
Part number
FLG-175B
FLG-275B
FLG-400B
FLHG-150C
Frequency range (Hz)
0.7G-2.5G
0.7G-2.5G
0.8G-2.5G
20M-3G
Max. output power typ. (W)
150
275
400
150
Output power @ 1dB compression,
typ. min. (W)
120
200
200
100
RF input, max. (dBm)
+10
+10
+10
0 (20-1000 MHz)
+10 (1-3 GHz)
Gain (dB), typ.
+52
+56
+56
+53
Flatness (dB), typ.
±2.5
±2.5
±3
±2.5
IP3 (dBm), typ.
+61
+61
+60
+58
Input VSWR, max.
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 120W
-20 @ 200W
-20 @ 250W
-15 @ 20M-1G @ 100W
-20 @ 1G-3G @ 100W
Spurious signals (dBc), typ.
<-60
<-60
<-60
<-60
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)/7/16 DIN
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
H
134
223
223
356
D
661
661
661
661
Weight (kg)
22
41
31
55
AC power input (W)
1600
3000
3000
3000
Power supply (VAC)
100-240
180-264
180-264
180-240
Phases
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
Cooling
Internal forced air
Internal forced air
Internal forced air
Internal forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• VSWR protection
• VSWR protection
• VSWR protection
Specifications at 25°C | Specifications subject to change without notice
13 // PAGE
1 GHz - 3 GHz
Part number
FLG-10C
FLG-15C
FLG-30C
FLG-50C
FLG-70C
FLG-120C
FLG-400C
Frequency range (Hz)
1G-3G
1G-3G
1G-3G
1G-3G
1G-3G
1G-3G
1G-3G
Max. output power typ. (W)
10
15
30
50
70
120
400
Output power @ 1dB compression,
typ. min. (W)
7
12
24
40
45
80
350
RF input, max. (dBm)
+10
+10
+10
+10
+10
+10
+10
Gain (dB), typ.
+38
+43
+46
+48
+49
+52
+57
Flatness (dB), typ.
±1.5
±1.5
±1.5
±2
±3
±3
±3.5
IP3 (dBm), typ.
+48
+51
+54
+56
+56
+56
+60
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 7W
-20 @ 12W
-20 @ 24W
-20 @ 40W
-20@45W
-20 @ 80W
-20 @ 300W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @
7W
<-60 @
12W
<-60 @
24W
<-60 @
40W
<-60 @
45W
<-60 @
80W
<-60 @
300W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
H
134
134
134
134
134
134
610
D
508
508
508
508
508
508
661
Weight (kg)
20
20
20
22
22
22
159
AC power input (W)
200
200
350
600
600
1200
12000
Power supply (VAC)
100-240
100-240
100-240
100-240
100-240
100-240
208
Phases
1
1
1
1
1
1
3
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
PAGE // 14
Specifications at 25°C | Specifications subject to change without notice
0.7 GHz - 3 GHz
Part number
FLG-15CA
FLG-30CA
FLG-70CA
FLG-120CA
FLG-250CA
Frequency range (Hz)
0.7G-3G
0.7G-3G
0.7G-3G
0.7G-3G
0.7G-3G
Max. output power typ. (W)
15
30
70
120
250
Output power @ 1dB compression,
typ. min. (W)
12
24
45
80
150
RF input, max. (dBm)
+10
+10
+6
+6
+10
Gain (dB), typ.
+43
+46
+49
+53
+55
Flatness (dB), typ.
±2
±2
±1.5
±1.5
±2.5
IP3 (dBm), typ.
+51
+54
+52
+56
+60
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 12W
-20 @ 24W
-20 @ 45W
-20 @ 80W
-20 @ 150W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 12W
<-60 @ 24W
<-60 @ 45W
<-60 @ 80W
<-60 @ 150W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
H
89
89
134
134
223
D
458
458
508
508
661
Weight (kg)
14
16
22
22
37
AC power input (W)
200
350
900
1800
3000
Power supply (VAC)
100-240
100-240
100-240
100-240
180-264
Phases
1
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Thermal overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
•VSWR protection
Specifications at 25°C | Specifications subject to change without notice
15 // PAGE
0.7 GHz - 4.2 GHz
Part number
FLG-7D
FLG-15D
FLG-28D
FLG-60D
FLG-100D
FLG-200D
Frequency range (Hz)
0.8G-4.2G
0.8G-4.2G
0.8G-4.2G
0.7G-4.2G
0.7G-4.2G
0.7G-4.2G
Max. output power typ. (W)
7
15
28
60
100
200
Output power @ 1dB compression,
typ. min. (W)
5
12
22
40
60
120
RF input, max. (dBm)
+10
+10
+10
+10
+10
+10
Gain (dB), typ.
+39
+43
+46
+49
+51
+55
Flatness (dB), typ.
±2
±2
±2.5
±3
±3
±2
IP3 (dBm), typ.
+47
+51
+54
+56
+56
+60
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 5W
-20 @ 12W
-20 @ 22W
-20 @ 45W
-20 @ 60W
-20 @ 120W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @ 5W
>-60 @ 12W
<-60 @ 22W
<-60 @ 45W
<-60 @ 60W
<-60 @ 120W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
H
134
89
134
134
223
356
D
458
458
508
508
661
661
Weight (kg)
12
14
22
20
37
68
AC power input (W)
75
200
350
1000
1500
5000
Power supply (VAC)
100-240
100-240
100-240
100-240
100-240
180-264
Phases
1
1
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
•VSWR protection
PAGE // 16
Specifications at 25°C | Specifications subject to change without notice
2 GHz - 4 GHz
Part number
FLG-15E
FLG-30E
FLG-50E
FLG-60E
FLG-100E
FLG-200E
FLG-600E
Frequency range (Hz)
2G-4G
2G-4G
2G-4G
2G-4G
2G-4G
2G-4G
2G-4G
Max. output power typ. (W)
15
30
50
60
100
200
600
Output power @ 1dB compression,
typ. min. (W)
12
24
40
40
60
120
400
RF input, max. (dBm)
+10
+10
+10
+10
+10
+10
0
Gain (dB), typ.
+43
+46
+48
+49
+51
+54
+58
Flatness (dB), typ.
±1.5
±1.5
±2
±3
±3.0
±3.0
±2.5
IP3 (dBm), typ.
+51
+54
+56
+56
+56
+56
+60
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
2:1
2:1
Harmonics @ 1 dB comp.,
(dBc), typ.
-20 @ 12W -20 @ 24W
-20 @ 40W
-20 @ 40W
-20 @ 60W
-20 @ 120W
-20 @ 400W
Spurious signals @ 1 dB comp.,
(dBc), typ.
<-60 @
12W
<-60 @
24W
<-60 @
40W
<-60 @
40W
<-60 @
60W
<-60 @
120W
<-60 @
400W
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
610 (24")
H
134
134
134
134
223
356
1524
D
508
508
508
508
661
661
661
Weight (kg)
14
16
22
22
34
57
182
AC power input (W)
200
350
600
600
2000
5000
16000
Power supply (VAC)
100-240
100-240
100-240
100-240
100-240
100-240
208-260
Phases
1
1
1
1
1
1
3
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Thermal
overload
• Over current
• Over current
• Over current
• Over current
• Over current
• Over current
• Over current
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
• Over voltage
Specifications at 25°C | Specifications subject to change without notice
17 // PAGE
PAGE // 18
2 GHz - 6 GHz
80 MHz - 6 GHz
Part number
FLG-9F
FLG-15F
FLG-30F
FLG-50F
FLG-100F
FLHG-300-1F
Frequency range (Hz)
2G-6G
2G-6G
2G-6G
2G-6G
2G-6G
Channel 1: 80M-1G
Channel 2: 100M-2.5G
Channel 3: 2.5G-6G
Max. output power typ. (W)
9
15
30
50
100
Channel 1: 280W
Channel 2: 80W
Channel 3: 50W
Output power @ 1dB compression,
typ. min. (W)
5
8-10
20-25
40
80
Channel 1: 150W
Channel 2: 60W
Channel 3: 30W
RF input, max. (dBm)
+3
+6
+3
0
+3
0
Gain (dB), typ.
+40
+43
+46
+50
+53
47-55
depending on channel
Flatness (dB), typ.
±2.5
±1.5
±2.5
±3
±3
±2.5 without ALC
±1.0 with internal
levelling
IP3 (dBm), typ.
+46
+50
+52
+54
+54
+8 above P1dB
Input VSWR, max.
2:1
2:1
2:1
2:1
2:1
2:1
Harmonics (dBc), typ.
-20
-20
-20
-20
-20
-20
Spurious signals (dBc), typ.
<-60
<-60
<-60
<-60
<-60
>-60
Input / output impedance (ohms)
50/50
50/50
50/50
50/50
50/50
50/50
Connectors in / out
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
N(f)N(f)
Dimensions (mm) W
483 (19")
483 (19")
483 (19")
483 (19")
483 (19")
1067 (42")
H
134
134
134
134
223
610
D
508
508
508
508
610
762
Weight (kg)
20
17
20
22
34
159
AC power input (W)
300
400
400
800
2000
Ch. 1: 4000W max.
Ch. 2: 1200W max.
Ch. 3: 800W max.
Power supply (VAC)
100-240
100-240
100-240
100-240
100-240
Ch. 1: 208-240
Ch. 2+3: 100-240
Phases
1
1
1
1
1
1
Operating temperature (°C)
0/+50
0/+50
0/+50
0/+50
0/+50
0/+50
Operating humidity
Non-condensing (%)
95
95
95
95
95
95
Cooling
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Internal
forced air
Circuit protection
• Thermal
overload
• Over current
•Over voltage
• Thermal
overload
• Over current
•Over voltage
• Thermal
overload
• Over current
•Over voltage
• Thermal
overload
• Over current
•Over voltage
• Thermal
overload
• Over current
•Over voltage
• Thermal overload
• Over current
•Over voltage
• VSWR protection
Specifications at 25°C | Specifications subject to change without notice
A typical application is immunity testing
acc. to IEC/EN 61000-4-3
Main characteristics
• 20 MHz – 3.0 GHz / 6 GHz
• Typical test level:
IEC/EN 61000-4-3: 10/30 V/m incl. 80% AM
• The RIS-3000/6000 combines the ECU (EMC Control Unit) and
RF-power amplifiers in one moveable 19” rack (incl. cabling)
• Antenna, field-strength meters, control software, anechoic
chambers and much more are optional available
PAGE
19 // Page
Copyright © by Frankonia EMC Test-Systems GmbH, 12-2012 / English Version 3.0
Frankonia EMC Test-Systems GmbH
Daimlerstraße 17, 91301 Forchheim
Germany
Frankonia GmbH
Industriestraße 16, 91180 Heideck
Germany
Web.www.frankoniagroup.com
Mail.sales@frankonia-emv.com
Web.www.frankoniagroup.com
Tel.
Fax.
+49 (0) 91 91 / 73 666 - 0
+49 (0) 91 91 / 73 666 - 20