Control of
Hazardous Energy
Lockout/Tagout
OSHA 3120
2002 (Revised)
Control of
Hazardous Energy
Lockout/ Tagout
U.S. Department of Labor
Elaine L. Chao, Secretary
Occupational Safety and Health Administration
John L. Henshaw, Assistant Secretary
OSHA 3120
2002 (Revised)
Contents
Page
Background ............................................................................... 1
How should I use this booklet? ............................................ 1
What is “lockout/tagout”? .................................................... 1
Why do I need to be concerned
about lockout/tagout? ........................................................... 2
OSHA Coverage ........................................................................ 3
How do I know if the OSHA standard
applies to me? ....................................................................... 3
When does the standard not apply to
service and maintenance activities performed
in industries covered by Part 1910? ..................................... 3
How does the standard apply to general
industry service and maintenance operations? .................... 4
Requirements of the Standard ................................................. 6
What are OSHA’s requirements? ......................................... 6
What must an energy-control procedure include? ............... 7
What must workers do before they
begin service or maintenance activities? ............................. 8
What must workers do before they
remove their lockout or tagout device
and reenergize the machine? ................................................ 8
When do I use lockout and how do I do it? ......................... 9
How can I determine if the energy-isolating
device can be locked out? .................................................. 10
What do I do if I cannot lock out
the equipment? ................................................................... 10
Contents
i
What other options do I have? ............................................11
When can tagout devices be used
instead of lockout devices? .................................................11
What are the limitations of tagout devices? ....................... 12
What are the requirements for
lockout/tagout devices? ...................................................... 12
What do employees need to know
about lockout/tagout programs? ......................................... 13
When is training necessary? ............................................... 14
What if I need power to test or position
machines, equipment, or components? .............................. 15
What if I use outside contractors for
service or maintenance procedures? .................................. 16
What if a group performs service
or maintenance activities? .................................................. 16
What if a shift changes during
machine service or maintenance? ...................................... 16
How often do I need to review
my lockout/tagout procedures? .......................................... 17
What does a review entail? ................................................ 17
What additional information does OSHA
provide about lockout/tagout? ............................................ 18
Commonly Used Terms .......................................................... 20
OSHA Assistance, Programs, and Services .......................... 22
How can OSHA help me? .................................................. 22
How does safety and health program management
assistance help employers and employees? ....................... 22
ii
Control of Hazardous Energy (Lockout/Tagout)
What are state plans? .......................................................... 23
How can consultation assistance
help employers? ................................................................. 23
Who can get consultation assistance
and what does it cost? ........................................................ 24
Can OSHA assure privacy to an employer
who asks for consultation assistance? ................................ 24
Can an employer be cited for violations
after receiving consultation assistance? ............................. 24
What incentives does OSHA provide for
seeking consultation assistance? ........................................ 24
What are the Voluntary Protection Programs? ................... 25
How does the VPP work? ................................................... 25
How does VPP help employers and employees? ............... 26
How does OSHA monitor VPP sites? ................................ 26
Can OSHA inspect an employer
who is participating in the VPP? ........................................ 26
How can a partnership with OSHA
improve worker safety and health? .................................... 27
What is OSHA’s Strategic Partnership
Program (OSPP)? ............................................................... 27
What do OSPPs do? ........................................................... 27
What are the different kinds of OSPPs? ............................ 28
What are the benefits of participation in the OSPP? ......... 28
Does OSHA have occupational safety and
health training for employers and employees? .................. 29
Does OSHA give money to organizations
for training and education? ................................................ 29
Contents
iii
Does OSHA have other assistance
materials available? ............................................................ 30
What do I do in case of an emergency
or to file a complaint? ........................................................ 31
OSHA Regional and Area Offices ......................................... 32
OSHA Consultation Projects ................................................. 36
OSHA-Approved Safety and Health Plans .......................... 38
iv
Control of Hazardous Energy (Lockout/Tagout)
Background
How should I use this booklet?
This booklet presents OSHA’s general requirements for
controlling hazardous energy during service or maintenance
of machines or equipment. It is not intended to replace or to
supplement OSHA standards regarding the control of hazardous
energy. After reading this booklet, employers and other
interested parties are urged to review the OSHA standards
on the control of hazardous energy to gain a complete
understanding of the requirements regarding the control of
hazardous energy. These standards, as well as other relevant
resources, are identified throughout this publication.
What is “lockout/tagout”?
“Lockout/tagout” refers to specific practices and procedures
to safeguard employees from the unexpected energization or
startup of machinery and equipment, or the release of hazardous
energy during service or maintenance activities.1 This requires,
in part, that a designated individual turns off and disconnects
the machinery or equipment from its energy source(s) before
performing service or maintenance and that the authorized
employee(s) either lock or tag the energy-isolating device(s) to
prevent the release of hazardous energy and take steps to verify
that the energy has been isolated effectively. If the potential
exists for the release of hazardous stored energy or for the
reaccumulation of stored energy to a hazardous level, the
employer must ensure that the employee(s) take steps to prevent
injury that may result from the release of the stored energy.
Lockout devices hold energy-isolation devices in a safe or
“off” position. They provide protection by preventing machines
or equipment from becoming energized because they are
1 The standard refers to servicing and maintaining “machines or
equipment.” Although the terms “machine” and “equipment” have
distinct meanings, this booklet uses the term “machines” to refer both
to machines and equipment. This is done for purposes of brevity only,
and readers should not infer that it is intended to limit the scope of the
standard. The term “equipment” is broad in scope and encompasses all
types of equipment, including process equipment such as piping systems.
How should I use this booklet?
1
positive restraints that no one can remove without a key or other
unlocking mechanism, or through extraordinary means, such as
bolt cutters. Tagout devices, by contrast, are prominent warning
devices that an authorized employee fastens to energy-isolating
devices to warn employees not to reenergize the machine while
he or she services or maintains it. Tagout devices are easier to
remove and, by themselves, provide employees with less
protection than do lockout devices.
Why do I need to be concerned about lockout/tagout?
Employees can be seriously or fatally injured if machinery
they service or maintain unexpectedly energizes, starts up, or
releases stored energy. OSHA’s standard on the Control of
Hazardous Energy (Lockout/Tagout), found in Title 29 of the
Code of Federal Regulations (CFR) Part 1910.147, spells out
the steps employers must take to prevent accidents associated
with hazardous energy. The standard addresses practices and
procedures necessary to disable machinery and prevent the
release of potentially hazardous energy while maintenance or
servicing activities are performed.
Two other OSHA standards also contain energy control
provisions: 29 CFR 1910.269 and 1910.333. In addition,
some standards relating to specific types of machinery contain
deenergization requirements —such as 29 CFR 1910.179(l)(2)(i)(c)
(requiring the switches to be “open and locked in the open position”
before performing preventive maintenance on overhead and gantry
cranes).2 The provisions of Part 1910.147 apply in conjunction
with these machine-specific standards to assure that employees will
be adequately protected against hazardous energy.
2 The standard provides a limited exception to the requirement that energy
control procedures be documented. If an employer can demonstrate the
existence of EACH of the eight elements listed in 1910.147(c)(4)(i),
the employer is not required to document the energy control procedure.
However, the exception terminates if circumstances change and ANY
of the elements no longer exist.
2
Control of Hazardous Energy (Lockout/Tagout)
OSHA Coverage
How do I know if the OSHA standard applies to me?
If your employees service or maintain machines where
the unexpected startup, energization, or the release of stored
energy could cause injury, the standard likely applies to you.
The standard applies to all sources of energy, including, but
not limited to: mechanical, electrical, hydraulic, pneumatic,
chemical, and thermal energy.
The standard does not cover electrical hazards from work
on, near, or with conductors or equipment in electric utilization
(premise wiring) installations, which are outlined by Subpart S
of 29 CFR Part 1910. You can find the specific lockout and
tagout provisions for electrical shock and burn hazards in
29 CFR Part 1910.333. Controlling hazardous energy in
installations for the exclusive purpose of power generation,
transmission, and distribution, including related equipment for
communication or metering, is covered by 29 CFR 1910.269.
The standard also does not cover the agriculture, construction,
and maritime industries or oil and gas well drilling and servicing.
Other standards concerning the control of hazardous energy,
however, apply in many of these industries/situations.
When does the standard not apply to service and maintenance
activities performed in industries covered by Part 1910?
The standard does not apply to general industry service
and maintenance activities in the following situations, when:
• Exposure to hazardous energy is controlled completely
by unplugging the equipment from an electric outlet and
where the employee doing the service or maintenance has
exclusive control of the plug. This applies only if electricity
is the only form of hazardous energy to which employees
may be exposed. This exception encompasses many
portable hand tools and some cord and plug connected
machinery and equipment.
How do I know if the OSHA standard applies to me?
3
• An employee performs hot-tap operations on pressurized
pipelines that distribute gas, steam, water, or petroleum
products, for which the employer shows the following:
– Continuity of service is essential;
– Shutdown of the system is impractical; and
– The employee follows documented procedures and
uses special equipment that provides proven, effective
employee protection.
• The employee is performing minor tool changes or other
minor servicing activities that are routine, repetitive, and
integral to production, and that occur during normal
production operations. In these cases, employees must
have effective, alternative protection.
How does the standard apply to general industry service
and maintenance operations?
The standard applies to the control of hazardous energy when
employees are involved in service or maintenance activities
such as constructing, installing, setting up, adjusting, inspecting,
modifying, and maintaining or servicing machines or equipment.
These activities include lubricating, cleaning or unjamming
machines, and making adjustments or tool changes, where
the employees may be exposed to hazardous energy.
If a service or maintenance activity is part of the normal
production operation, the employee performing the servicing
may be subjected to hazards not normally associated with
the production operation itself. Although machine guarding
provisions in Subpart O of 29 CFR 1910 cover most normal
production operations, workers doing service or maintenance
activities during normal production operations must follow
lockout/tagout procedures if they:
• Remove or bypass machine guards or other safety devices,
• Place any part of their bodies in or near a machine’s point
of operation, or
4
Control of Hazardous Energy (Lockout/Tagout)
• Place any part of their bodies in a danger zone associated
with machine operations.
Work involving minor tool changes and adjustments or
other minor servicing activities that are routine, repetitive, and
integral to the use of the production equipment and that occur
during normal production operations are not covered by the
lockout/tagout standard. This exception is limited, however, and
applies only when economic considerations prevent the use of
prescribed energy-isolation measures and when the employer
provides and requires alternative measures to ensure effective,
alternative protection.
Whenever the standard is applicable, the machinery must
be shut off and isolated from its energy sources, and lockout or
tagout devices must be applied to the energy-isolation devices.
In addition, the authorized employee(s) must take steps to verify
that he or she has effectively isolated the energy. When there
is stored or residual energy, the authorized employee(s) must
take steps to render that energy safe. If the possibility exists
for reaccumulation of stored energy to hazardous levels, the
employer must ensure that the worker(s) perform verification
steps regularly to detect such reaccumulation before it has the
potential to cause injury.
How does the standard apply to general industry operations?
5
Requirements of the Standard
What are OSHA’s requirements?
OSHA’s standard establishes minimum performance
requirements for controlling hazardous energy. The standard
specifies that employers must establish an energy-control
program to ensure that employees isolate machines from
their energy sources and render them inoperative before
any employee services or maintains them.
As part of an energy-control program, employers must:
• Establish energy-control procedures for removing the
energy supply from machines and for putting appropriate
lockout or tagout devices on the energy-isolating devices
to prevent unexpected reenergization. When appropriate,
the procedure also must address stored or potentially
reaccumulated energy;
• Train employees on the energy-control program, including
the safe application, use, and removal of energy controls;
and
• Inspect these procedures periodically (at least annually)
to ensure that they are being followed and that they remain
effective in preventing employee exposure to hazardous
energy.
If employers use tagout devices on machinery that can be
locked out, they must adopt additional measures to provide the
same level of employee protection that lockout devices would
provide. Within the broad boundaries of the standard, employers
have the flexibility to develop programs and procedures that
meet the needs of their individual workplaces and the particular
types of machines being maintained or serviced.
6
Control of Hazardous Energy (Lockout/Tagout)
What must an energy-control procedure include?
Employers must develop, document, and use procedures
to control potentially hazardous energy.3 The procedures
explain what employees must know and do to control hazardous
energy effectively when they service or maintain machinery.
If this information is the same for the various machines used at
a workplace, then a single energy-control procedure may suffice.
For example, similar machines (those using the same type and
magnitude of energy) that have the same or similar types of
control measures can be covered by a single procedure.
Employers must develop separate energy-control procedures
if their workplaces have more variable conditions such as
multiple energy sources, different power connections, or
different control sequences that workers must follow to shut
down various pieces of machinery.
The energy-control procedures must outline the scope,
purpose, authorization, rules, and techniques that employees
will use to control hazardous energy sources, as well as
the means that will be used to enforce compliance. These
procedures must provide employees at least the following
information:
• A statement on how to use the procedures;
• Specific procedural steps to shut down, isolate, block,
and secure machines;
• Specific steps designating the safe placement, removal,
and transfer of lockout/tagout devices and identifying
who has responsibility for the lockout/tagout devices; and
• Specific requirements for testing machines to determine
and verify the effectiveness of lockout devices, tagout
devices, and other energy-control measures.
3 The standard provides a limited exception to the requirement that energy
control procedures be documented. If an employer can demonstrate the
existence of EACH of the eight elements listed in 1910.147(c)(4)(i),
the employer is not required to document the energy control procedure.
However, the exception terminates if circumstances change and ANY
of the elements no longer exist.
What must an energy-control procedure include?
7
In Appendix A to 1910.147, OSHA provides a Typical
Minimal Lockout Procedure for employers to consult when
preparing their own specific energy-control procedures. The
outline is a nonmandatory guideline to help employers and
employees comply with the standard. Nothing in the appendix
adds to or detracts from any of the requirements in the standard.
What must workers do before they begin service
or maintenance activities?
Before beginning service or maintenance, the following
steps must be accomplished in sequence and according to the
specific provisions of the employer’s energy-control procedure:
(1) Prepare for shutdown;
(2) Shut down the machine;
(3) Disconnect or isolate the machine from the energy
source(s);
(4) Apply the lockout or tagout device(s) to the
energy-isolating device(s);
(5) Release, restrain, or otherwise render safe all potential
hazardous stored or residual energy. If a possibility
exists for reaccumulation of hazardous energy, regularly
verify during the service and maintenance that such
energy has not reaccumulated to hazardous levels; and
(6) Verify the isolation and deenergization of the machine.
What must workers do before they remove their
lockout or tagout device and reenergize the machine?
Employees who work on deenergized machinery may
be seriously injured or killed if someone removes lockout/tagout
devices and reenergizes machinery without their knowledge.
Thus, it is extremely important that all employees respect lockout
and tagout devices and that only the person(s) who applied these
devices remove them.
8
Control of Hazardous Energy (Lockout/Tagout)
Before removing lockout or tagout devices, the employees
must take the following steps in accordance with the specific
provisions of the employer’s energy-control procedure:
• Inspect machines or their components to assure that they
are operationally intact and that nonessential items are
removed from the area; and
• Check to assure that everyone is positioned safely and
away from machines.
After removing the lockout or tagout devices but before
reenergizing the machine, the employer must assure that all
employees who operate or work with the machine, as well as
those in the area where service or maintenance is performed,
know that the devices have been removed and that the machine
is capable of being reenergized. (See Sections 6(e) and (f) of
29 CFR Part 1910.147 for specific requirements.) In the rare
situation in which the employee who placed the lockout/tagout
device is unable to remove that device, another person may
remove it under the direction of the employer, provided that the
employer strictly adheres to the specific procedures outlined in
the standard. (See 29 CFR 1910.147(e)(3).)
When do I use lockout and how do I do it?
You must use a lockout program (or tagout program that
provides a level of protection equal to that achieved through
lockout) whenever your employees engage in service or
maintenance operations on machines that are capable of being
locked out and that expose them to hazardous energy from
unexpected energization, startup, or release of stored energy.
The primary way to prevent the release of hazardous
energy during service and maintenance activities is by using
energy-isolating devices such as manually operated circuit
breakers, disconnect switches, and line valves and safety
blocks. Lockout requires use of a lock or other lockout device
to hold the energy-isolating device in a safe position to prevent
machinery from becoming reenergized. Lockout also requires
What must workers do before they remove their lockout or tagout device?
9
employees to follow an established procedure to ensure that
machinery will not be reenergized until the same employee
who placed the lockout device on the energy-isolating device
removes it.
How can I determine if the energy-isolating device
can be locked out?
An energy-isolating device is considered “capable of being
locked out” if it meets one of the following requirements:
• Is designed with a hasp or other part to which you can
attach a lock such as a lockable electric disconnect switch;
• Has a locking mechanism built into it; or
• Can be locked without dismantling, rebuilding, or replacing
the energy-isolating device or permanently altering its
energy-control capability, such as a lockable valve cover
or circuit breaker blockout.
What do I do if I cannot lock out the equipment?
Sometimes it is not possible to lock out the energy-isolating
device associated with the machinery. In that case, you must
securely fasten a tagout device as close as safely possible to the
energy-isolating device in a position where it will be immediately
obvious to anyone attempting to operate the device. You also
must meet all of the tagout provisions of the standard. The tag
alerts employees to the hazard of reenergization and states that
employees may not operate the machinery to which it is attached
until the tag is removed in accordance with an established
procedure.
10
Control of Hazardous Energy (Lockout/Tagout)
What other options do I have?
If it is possible to lock out an energy-isolating device,
employers must use lockout devices unless they develop,
document, and use a tagout procedure that provides
employees with a level of protection equal to that provided
by a lockout device. In a tagout program, an employer can
attain an equal level of protection by complying with all
tagout-related provisions of the standard and using at least one
added safety measure that prevents unexpected reenergization.
Such measures might include removing an isolating circuit
element, blocking a controlling switch, opening an extra
disconnecting device, or removing a valve handle to minimize
the possibility that machines might inadvertently be reenergized
while employees perform service and maintenance activities.
When can tagout devices be used instead of lockout devices?
When an energy-isolating device cannot be locked out, the
employer must modify or replace the energy-isolating device
to make it capable of being locked out or use a tagout system.
Whenever employers significantly repair, renovate, or modify
machinery or install new or replacement machinery, however,
they must ensure that the energy-isolating devices for the
machinery are capable of being locked out.
Tagout devices may be used on energy-isolating devices
that are capable of being locked out if the employer develops
and implements the tagout in a way that provides employees
with a level of protection equal to that achieved through a
lockout system.
When using a tagout system, the employer must comply
with all tagout-related provisions of the standard and train
employees in the limitations of tags, in addition to providing
normal hazardous energy control training for all employees.
What other options do I have?
11
What are the limitations of tagout devices?
A tagout device is a prominent warning that clearly states
that the machinery being controlled must not be operated until
the tag is removed in accordance with an established procedure.
Tags are essentially warning devices and do not provide the
physical restraint of a lock. Tags may evoke a false sense of
security. For these reasons, OSHA considers lockout devices
to be more secure and more effective than tagout devices in
protecting employees from hazardous energy.
What are the requirements for lockout/tagout devices?
Whether lockout or tagout devices are used, they must
be the only devices the employer uses in conjunction with
energy-isolating devices to control hazardous energy.
The employer must provide these devices and they must
be singularly identified and not used for other purposes.
In addition, they must have the following characteristics:
• Durable enough to withstand workplace conditions.
Tagout devices must not deteriorate or become illegible
even when used with corrosive components such as acid
or alkali chemicals or in wet environments.
• Standardized according to color, shape, or size. Tagout
devices also must be standardized according to print and
format. Tags must be legible and understandable by all
employees. They must warn employees about the hazards
if the machine is energized, and offer employees clear
instruction such as: “Do Not Start,” “Do Not Open,”
“Do Not Close,” “Do Not Energize,” or “Do Not Operate.”
• Substantial enough to minimize the likelihood of
premature or accidental removal. Employees should be
able to remove locks only by using excessive force with
special tools such as bolt cutters or other metal-cutting
tools. Tag attachments must be non-reusable, self-locking,
and non-releasable, with a minimum unlocking strength
12
Control of Hazardous Energy (Lockout/Tagout)
of 50 pounds. Tags must be attachable by hand, and
the device for attaching the tag should be a one-piece
nylon cable tie or its equivalent so it can withstand all
environments and conditions.
• Labeled to identify the specific employees authorized to
apply and remove them.
What do employees need to know about lockout/tagout programs?
Training must ensure that employees understand the
purpose, function, and restrictions of the energy-control
program. Employers must provide training specific to the
needs of “authorized,” “affected,” and “other” employees.
“Authorized” employees are those responsible for
implementing the energy-control procedures or performing
the service or maintenance activities. They need the
knowledge and skills necessary for the safe application,
use, and removal of energy-isolating devices. They also
need training in the following:
• Hazardous energy source recognition;
• The type and magnitude of the hazardous energy
sources in the workplace; and
• Energy-control procedures, including the methods and
means to isolate and control those energy sources.
“Affected” employees (usually machine operators or users)
are employees who operate the relevant machinery or whose
jobs require them to be in the area where service or maintenance
is performed. These employees do not service or maintain
machinery or perform lockout/tagout activities. Affected
employees must receive training in the purpose and use of
energy-control procedures. They also need to be able to do
the following:
• Recognize when the energy-control procedure is being
used,
What are the requirements for lockout/tagout devices?
13
• Understand the purpose of the procedure, and
• Understand the importance of not tampering with lockout
or tagout devices and not starting or using equipment
that has been locked or tagged out.
All other employees whose work operations are or may
be in an area where energy-control procedures are used must
receive instruction regarding the energy-control procedure
and the prohibition against removing a lockout or tagout
device and attempting to restart, reenergize, or operate
the machinery.
In addition, if tagout devices are used, all employees
must receive training regarding the limitations of tags.
(See 29 CFR 1910.147(c)(7)(ii).)
When is training necessary?
The employer must provide initial training before starting
service and maintenance activities and must provide retraining
as necessary. In addition, the employer must certify that
the training has been given to all employees covered by the
standard. The certification must contain each employee’s name
and dates of training.
Employers must provide retraining for all authorized and
affected employees whenever there is a change in the following:
• Job assignments,
• Machinery or processes that present a new hazard, or
• Energy-control procedures.
Retraining also is necessary whenever a periodic inspection
reveals, or an employer has reason to believe, that shortcomings
exist in an employee’s knowledge or use of the energy-control
procedure.
14
Control of Hazardous Energy (Lockout/Tagout)
What if I need power to test or position machines, equipment,
or components?
OSHA allows the temporary removal of lockout or tagout
devices and the reenergization of the machine only in limited
situations for particular tasks that require energization — for
example, when power is needed to test or position machines,
equipment, or components. However, this temporary exception
applies only for the limited time required to perform the
particular task requiring energization. Employers must provide
effective protection from hazardous energy when employees
perform these operations. The following steps must be
performed in sequence before reenergization:
1. Clear tools and materials from machines.
2. Clear employees from the area around the machines.
3. Remove the lockout or tagout devices as specified in
the standard.
4. Energize the machine and proceed with testing or
positioning.
5. Deenergize all systems, isolate the machine from the
energy source, and reapply energy-control measures
if additional service or maintenance is required.
The employer must develop, document, and use energy-control
procedures that establish a sequence of actions to follow whenever
reenergization is required as a part of a service or maintenance
activity, since employees may be exposed to significant risks
during these transition periods.
What if I need power to test or position machines?
15
What if I use outside contractors for service
or maintenance procedures?
If an outside contractor services or maintains machinery,
the onsite employer and the contractor must inform each other
of their respective lockout or tagout procedures. The onsite
employer also must ensure that employees understand and
comply with all requirements of the contractor’s energy-control
program(s).
What if a group performs service or maintenance activities?
When a crew, department, or other group performs service
or maintenance, they must use a procedure that provides all
employees a level of protection equal to that provided by
a personal lockout or tagout device. Each employee in the
group must have control over the sources of hazardous energy
while he or she is involved in service and maintenance activities
covered by the standard. Personal control is achieved when each
authorized employee affixes a personal lockout/tagout device to
a group lockout mechanism instead of relying on a supervisor
or other person to provide protection against hazardous energy.
Detailed requirements of individual responsibilities are provided
in 29 CFR 1910.147(f)(3)(ii)(A) through (D). Appendix C of
OSHA Directive STD 1-7.3, 29 CFR 1910.147, the Control of
Hazardous Energy (Lockout/Tagout)-Inspection Procedures
and Interpretive Guidance, (September 11, 1990), provides
additional guidance.
What if a shift changes during machine service or maintenance?
Employers must make sure that there is a continuity of
lockout or tagout protection. This includes the orderly transfer
of lockout or tagout device protection between outgoing and
incoming shifts to control hazardous energy. When lockout
or tagout devices remain on energy-isolation devices from
a previous shift, the incoming shift members must verify
for themselves that the machinery is effectively isolated
and deenergized.
16
Control of Hazardous Energy (Lockout/Tagout)
How often do I need to review my lockout/tagout procedures?
Employees are required to review their procedures at least
once a year to ensure that they provide adequate worker
protection. As part of the review, employers must correct any
deviations and inadequacies identified in the energy-control
procedure or its application.
What does a review entail?
The periodic inspection is intended to assure that employees
are familiar with their responsibilities under the procedure and
continue to implement energy-control procedures properly.
The inspector, who must be an authorized person not involved
in using the particular control procedure being inspected, must
be able to determine the following:
• Employees are following steps in the energy-control
procedure;
• Employees involved know their responsibilities under
the procedure; and
• The procedure is adequate to provide the necessary
protection, and what changes, if any, are needed.
For a lockout procedure, the periodic inspection must
include a review of each authorized employee’s responsibilities
under the energy-control procedure being inspected. Where
tagout is used, the inspector’s review also extends to affected
employees because of the increased importance of their role in
avoiding accidental or inadvertent activation of the machinery.
In addition, the employer must certify that the designated
inspectors perform periodic inspections. The certification
must specify the following:
• Machine or equipment on which the energy-control
procedure was used,
• Date of the inspection,
• Names of employees included in the inspection, and
• Name of the person who performed the inspection.
How often do I need to review my lockout/tagout procedures?
17
What additional information does OSHA provide
about lockout/tagout?
To gain a more comprehensive understanding of the
requirements for controlling hazardous energy, employers
and other interested persons should review the following:
• OSHA standards with provisions regarding the control of
hazardous energy such as 29 CFR 1910.147, The control
of hazardous energy (lockout/tagout); 29 CFR 1910.269,
Electric power generation, transmission, and distribution;
and 29 CFR 1910.333, Selection and use of work practices.
Employers in the maritime, agriculture, and construction
industries are urged to review the provisions for the control
of hazardous energy contained in 29 CFR Parts 1915, 1917,
1918, 1925, and 1926.
• The regulatory preambles to 29 CFR 1910.147
(54 Federal Register 36644 (September 1, 1989)) and
1910.269 (59 Federal Register 4320 (January 31, 1994)),
which contain comments from interested parties and
OSHA’s explanation for the provisions of the standards.
• OSHA instructions concerning the control of hazardous
energy — Directive CPL 2-1.18A, Enforcement of the
Electrical Power Generation, Transmission, and Distribution
Standard (October 20, 1997) and OSHA Directive
STD 1-7.3, 29 CFR 1910.147, the Control of Hazardous
Energy (Lockout/Tagout) -Inspection Procedures and
Interpretive Guidance, (September 11, 1990).
• OSHA letters of interpretation regarding the application
of standards concerning the control of hazardous energy.
Most of these documents are available on the OSHA
website at www.osha.gov.
18
Control of Hazardous Energy (Lockout/Tagout)
Additionally, OSHA offers a variety of web-based tools to
help educate employers and employees about the lockout/tagout
standard and how to apply it in their workplace. These include
the following:
• The Lockout/Tagout Interactive Training Program, which
includes a tutorial, five abstracts with a detailed discussion
of major lockout/tagout issues involved, and interactive
case studies;
• The Lockout/Tagout Plus Expert Advisor, an interactive,
expert, diagnostic software package to help users
understand and apply OSHA standards that protect workers
from the release of hazardous energy; and
• The Lockout/Tagout electronic Compliance Assistant Tool
(eCAT), an illustrated tool to help businesses identify and
correct workplace hazards.
These tools are available on the OSHA website at
www.osha.gov. For the Lockout/Tagout Interactive Training
Program, click on Technical Links. For the Expert Advisor and
eCAT, click on eTools.
What additional information does OSHA provide about lockout/tagout?
19
Commonly Used Terms
Affected employee. An employee whose job requires
him/her to operate or use a machine or equipment on which
servicing or maintenance is being performed under lockout
or tagout, or whose job requires him/her to work in an area
in which such servicing or maintenance is being performed.
Authorized employee. A person who locks out or tags
out machines or equipment in order to perform servicing
or maintenance on that machine or equipment. An affected
employee becomes an authorized employee when that
employee’s duties include performing servicing or
maintenance covered under the standard.
Capable of being locked out. An energy-isolating device is
capable of being locked out if it has a hasp or other means of
attachment to which, or through which, a lock can be affixed, or
it has a locking mechanism built into it. Other energy-isolating
devices are capable of being locked out, if lockout can be achieved,
without the need to dismantle, rebuild, or replace the energyisolating device or permanently alter its energy control capability.
Energized. Connected to an energy source or containing
residual or stored energy.
Energy-isolating device. A mechanical device that physically
prevents the transmission or release of energy, including but not
limited to the following: a manually operated electrical circuit
breaker; a disconnect switch; a manually operated switch by
which the conductors of a circuit can be disconnected from
all ungrounded supply conductors, and in addition, no pole
can be operated independently; a line valve; a block; and any
similar device used to block or isolate energy. Push buttons,
selector switches and other control circuit-type devices are
not energy-isolating devices.
Energy source. Any source of electrical, mechanical,
hydraulic, pneumatic, chemical, thermal, or other energy.
Hot tap. A procedure used in the repair, maintenance,
and services activities, which involve welding on a piece of
equipment (pipelines, vessels, or tanks) under pressure, in order
to install connections or appurtenances. It is commonly used
20
Control of Hazardous Energy (Lockout/Tagout)
to replace or add sections of pipeline without the interruption
of service for air, gas, water, steam, and petrochemical
distribution systems.
Lockout. The placement of a lockout device on an
energy-isolating device, in accordance with an established
procedure, ensuring that the energy-isolating device and the
equipment being controlled cannot be operated until the
lockout device is removed.
Lockout device. A device that uses a positive means such
as a lock, either key or combination type, to hold an energyisolating device in the safe position and prevent the energizing
of a machine or equipment. Included are blank flanges and
bolted slip blinds.
Normal production operations. The utilization of a machine
or equipment to perform its intended production function.
Servicing and/or maintenance. Workplace activities such
as constructing, installing, setting up, adjusting, inspecting,
modifying, and maintaining and/or servicing machines or
equipment. These activities include lubricating, cleaning or
unjamming machines or equipment and making adjustments
or tool changes where the employee may be exposed to the
unexpected energization or startup of the equipment or release
of hazardous energy.
Setting up. Any work performed to prepare a machine or
equipment to perform its normal production operation.
Tagout. The placement of a tagout device on an energyisolating device, in accordance with an established procedure,
to indicate that the energy-isolating device and the equipment
being controlled may not be operated until the tagout device
is removed.
Tagout device. A prominent warning device, such as a tag
and a means of attachment, which can be securely fastened to
an energy-isolating device in accordance with an established
procedure, to indicate that the energy-isolating device and
the equipment being controlled may not be operated until the
tagout device is removed.
Commonly Used Terms
21
OSHA Assistance, Programs, and Services
How can OSHA help me?
OSHA can provide extensive help through a variety of
programs, including assistance about safety and health
programs, state plans, workplace consultations, voluntary
protection programs, strategic partnerships, training and
education, and more.
How does safety and health program management assistance
help employers and employees?
Effective management of worker safety and health
protection is a decisive factor in reducing the extent and
severity of work-related injuries and illnesses and their related
costs. In fact, an effective safety and health program forms the
basis of good worker protection and can save time and money
— about $4 for every dollar spent — and increase productivity.
To assist employers and employees in developing effective
safety and health programs, OSHA published recommended
Safety and Health Program Management Guidelines (Federal
Register 54(18):3908-3916, January 26, 1989). These voluntary
guidelines can be applied to all worksites covered by OSHA.
The guidelines identify four general elements that are
critical to the development of a successful safety and health
management program:
• Management leadership and employee involvement,
• Worksite analysis,
• Hazard prevention and control, and
• Safety and health training.
The guidelines recommend specific actions under each of
these general elements to achieve an effective safety and health
program. The Federal Register notice is available online at
www.osha.gov.
22
Control of Hazardous Energy (Lockout/Tagout)
What are state plans?
State plans are OSHA-approved job safety and health
programs operated by individual states or territories instead
of Federal OSHA. The Occupational Safety and Health Act
of 1970 (OSH Act) encourages states to develop and operate
their own job safety and health plans and permits state
enforcement of OSHA standards if the state has an approved
plan. Once OSHA approves a state plan, it funds 50 percent
of the program’s operating costs. State plans must provide
standards and enforcement programs, as well as voluntary
compliance activities that are at least as effective as those
of Federal OSHA.
There are 26 state plans: 23 cover both private and public
(state and local governments) employment, and 3 (Connecticut,
New Jersey, and New York) cover only the public sector.
For more information on state plans, see the listing at the end
of this publication, or visit OSHA’s website at www.osha.gov.
How can consultation assistance help employers?
In addition to helping employers identify and correct
specific hazards, OSHA’s consultation service provides free,
onsite assistance in developing and implementing effective
workplace safety and health management systems that
emphasize the prevention of worker injuries and illnesses.
Comprehensive consultation assistance provided by OSHA
includes a hazard survey of the worksite and an appraisal of all
aspects of the employer’s existing safety and health management
system. In addition, the service offers assistance to employers
in developing and implementing an effective safety and health
management system. Employers also may receive training and
education services, as well as limited assistance away from the
worksite.
What are state plans?
23
Who can get consultation assistance and what does it cost?
Consultation assistance is available to small employers
with fewer than 250 employees at a fixed site and no more
than 500 corporatewide who want help in establishing and
maintaining a safe and healthful workplace.
Funded largely by OSHA, the service is provided at no cost
to the employer. Primarily developed for smaller employers
with more hazardous operations, the consultation service is
delivered by state governments employing professional safety
and health consultants. No penalties are proposed or citations
issued for hazards identified by the consultant. The employer’s
only obligation is to correct all identified serious hazards within
the agreed-upon correction time frame.
Can OSHA assure privacy to an employer who asks for
consultation assistance?
OSHA provides consultation assistance to the employer with
the assurance that his or her name and firm and any information
about the workplace will not be routinely reported to OSHA
enforcement staff.
Can an employer be cited for violations after receiving
consultation assistance?
If an employer fails to eliminate or control a serious hazard
within the agreed-upon timeframe, the Consultation Project
Manager must refer the situation to the OSHA enforcement
office for appropriate action. This is a rare occurrence,
however, since employers request the service for the expressed
purpose of identifying and fixing hazards in their workplaces.
What incentives does OSHA provide for seeking
consultation assistance?
Under the consultation program, certain exemplary
employers may request participation in OSHA’s Safety and
Health Achievement Recognition Program (SHARP). Eligibility
24
Control of Hazardous Energy (Lockout/Tagout)
for participation in SHARP includes, but is not limited to,
receiving a full-service, comprehensive consultation visit,
correcting all identified hazards, and developing an effective
safety and health management system.
Employers accepted into SHARP may receive an exemption
from programmed inspections (not complaint or accident
investigation inspections) for a period of 1 year initially, or
2 years upon renewal.
For more information concerning consultation assistance, see
the list of consultation offices beginning on page 34, contact
your regional or area OSHA office, or visit OSHA’s website at
www.osha.gov.
What are the Voluntary Protection Programs?
Voluntary Protection Programs (VPPs) represent one part
of OSHA’s effort to extend worker protection beyond the
minimum required by OSHA standards. VPP— along with
onsite consultation services, full-service area offices, and
OSHA’s Strategic Partnership Program (OSPP) — represents a
cooperative approach which, when coupled with an effective
enforcement program, expands worker protection to help meet
the goals of the OSH Act.
How does the VPP work?
There are three levels of VPPs: Star, Merit, and Demonstration.
All are designed to do the following:
• Recognize employers who have successfully developed
and implemented effective and comprehensive safety and
health management systems;
• Encourage these employers to continuously improve
their safety and health management systems;
• Motivate other employers to achieve excellent safety
and health results in the same outstanding way; and
• Establish a relationship between employers, employees,
and OSHA that is based on cooperation.
What incentives does OSHA provide for seeking consultation assistance?
25
How does VPP help employers and employees?
VPP participation can mean the following:
• Reduced numbers of worker fatalities, injuries, and
illnesses;
• Lost-workday case rates generally 50 percent below
industry averages;
• Lower workers’ compensation and other injury- and
illness-related costs;
• Improved employee motivation to work safely,
leading to a better quality of life at work;
• Positive community recognition and interaction;
• Further improvement and revitalization of already-good
safety and health programs; and
• A positive relationship with OSHA.
How does OSHA monitor VPP sites?
OSHA reviews an employer’s VPP application and conducts
a VPP Onsite Evaluation to verify that the safety and health
management systems described are operating effectively at
the site. OSHA conducts onsite evaluations on a regular basis,
annually for participants at the Demonstration level, every 18
months for Merit, and every 3 to 5 years for Star. Each February,
all participants must send a copy of their most recent annual
evaluation to their OSHA regional office. This evaluation must
include the worksite’s record of injuries and illnesses for the
past year.
Can OSHA inspect an employer who is participating in the VPP?
Sites participating in VPP are not scheduled for regular,
programmed inspections. OSHA handles any employee
complaints, serious accidents, or significant chemical releases
that may occur at VPP sites according to routine enforcement
procedures.
26
Control of Hazardous Energy (Lockout/Tagout)
Additional information on VPP is available from OSHA
national, regional, and area offices, listed beginning on page 34.
Also, see Outreach at OSHA’s website at www.osha.gov.
How can a partnership with OSHA improve worker safety and health?
OSHA has learned firsthand that voluntary, cooperative
partnerships with employers, employees, and unions can be a
useful alternative to traditional enforcement and an effective
way to reduce worker deaths, injuries, and illnesses. This is
especially true when a partnership leads to the development and
implementation of a comprehensive workplace safety and health
management system.
What is OSHA’s Strategic Partnership Program (OSPP)?
OSHA Strategic Partnerships are alliances among labor,
management, and government to foster improvements in
workplace safety and health. These partnerships are voluntary,
cooperative relationships between OSHA, employers, employee
representatives, and others such as trade unions, trade and
professional associations, universities, and other government
agencies. OSPPs are the newest member of OSHA’s family of
cooperative programs.
What do OSPPs do?
These partnerships encourage, assist, and recognize the
efforts of the partners to eliminate serious workplace hazards
and achieve a high level of worker safety and health. Whereas
OSHA’s Consultation Program and VPP entail one-on-one
relationships between OSHA and individual worksites, most
strategic partnerships seek to have a broader impact by
building cooperative relationships with groups of employers
and employees.
Can OSHA inspect an employer who is participating in the VPP?
27
What are the different kinds of OSPPs?
There are two major types:
• Comprehensive, which focuses on establishing
comprehensive safety and health management systems
at partnering worksites; and
• Limited, which helps identify and eliminate hazards
associated with worker deaths, injuries, and illnesses, or
have goals other than establishing comprehensive worksite
safety and health programs.
OSHA is interested in creating new OSPPs at the national,
regional, and local levels. OSHA also has found limited
partnerships to be valuable. Limited partnerships might address
the elimination or control of a specific industry hazard.
What are the benefits of participation in the OSPP?
Like VPP, OSPP can mean the following:
• Fewer worker fatalities, injuries, and illnesses;
• Lower workers’ compensation and other injury- and
illness-related costs;
• Improved employee motivation to work safely, leading to
a better quality of life at work and enhanced productivity;
• Positive community recognition and interaction;
• Development of or improvement in safety and health
management systems; and
• Positive interaction with OSHA.
For more information about this program, contact your nearest
OSHA office or go to the agency website at www.osha.gov.
28
Control of Hazardous Energy (Lockout/Tagout)
Does OSHA have occupational safety and health training for
employers and employees?
Yes. The OSHA Training Institute in Des Plaines, IL,
provides basic and advanced training and education in safety
and health for federal and state compliance officers, state
consultants, other federal agency personnel, and private-sector
employers, employees, and their representatives.
Institute courses cover diverse safety and health topics
including electrical hazards, machine guarding, personal
protective equipment, ventilation, and ergonomics. The facility
includes classrooms, laboratories, a library, and an audiovisual
unit. The laboratories contain various demonstrations and
equipment, such as power presses, woodworking and welding
shops, a complete industrial ventilation unit, and a sound
demonstration laboratory. More than 57 courses dealing with
subjects such as safety and health in the construction industry
and methods of compliance with OSHA standards are available
for personnel in the private sector.
In addition, OSHA’s 73 area offices are full-service centers
offering a variety of informational services such as personnel
for speaking engagements, publications, audiovisual aids on
workplace hazards, and technical advice.
Does OSHA give money to organizations for training and education?
OSHA awards grants through its Susan Harwood Training
Grant Program to nonprofit organizations to provide safety and
health training and education to employers and workers in the
workplace. The grants focus on programs that will educate
workers and employers in small business (fewer than 250
employees), train workers and employers about new OSHA
standards, or a high-risk activities or hazards. Grants are
awarded for 1 year and may be renewed for an additional 12 months
depending on whether the grantee has performed satisfactorily.
Does OSHA have occupational safety and health training?
29
OSHA expects each organization awarded a grant to develop
a training and/or education program that addresses a safety and
health topic named by OSHA, recruit workers and employers
for the training, and conduct the training. Grantees are also
expected to follow up with people who have been trained to
find out what changes were made to reduce the hazards in their
workplaces as a result of the training.
Each year OSHA has a national competition that is announced
in the Federal Register and on the Internet at www.osha-slc.gov/
Training/sharwood/sharwood.html. If you do not have access
to the Internet, you can contact the OSHA Office of Training
and Education, 1555 Times Drive, Des Plaines, IL 60018,
(847) 297–4810, for more information.
Does OSHA have other assistance materials available?
Yes. OSHA has a variety of materials and tools available
on its website at www.osha.gov. These include eTools, Expert
Advisors, Electronic Compliance Assistance Tools (eCATS),
Technical Links, regulations, directives, publications, videos,
and other information for employers and employees. OSHA’s
software programs and compliance assistance tools walk you
through challenging safety and health issues and common
problems to find the best solutions for your workplace. OSHA’s
comprehensive publications program includes more than 100
titles to help you understand OSHA requirements and programs.
OSHA’s CD-ROM includes standards, interpretations,
directives, and more and can be purchased on CD-ROM from
the U.S. Government Printing Office. To order, write to the
Superintendent of Documents, U.S. Government Printing Office,
Washington, DC 20402, or phone (202) 512–1800. Specify
OSHA Regulations, Documents and Technical Information on
CD-ROM (ORDT), GPO Order No. S/N 729-013-00000-5.
30
Control of Hazardous Energy (Lockout/Tagout)
What do I do in case of an emergency or to file a complaint?
To report an emergency, file a complaint, or seek OSHA
advice, assistance, or products, call (800) 321– OSHA or
contact your nearest OSHA regional or area office listed at the
end of this publication. The teletypewriter (TTY) number is
(877) 889–5627.
You can also file a complaint online and obtain more
information on OSHA federal and state programs by visiting
OSHA’s website at www.osha.gov.
For more information on grants, training, and education,
write: OSHA Training Institute, Office of Training and
Education, 1555 Times Drive, Des Plaines, IL 60018;
call (847) 297-4810; or see Outreach on OSHA’s website
at www.osha.gov.
What do I do in case of an emergency or to file a complaint?
31
OSHA Regional and Area Offices
OSHA Regional Offices
Region I
Region VI
(CT,* MA, ME, NH, RI, VT*)
JFK Federal Building
Room E-340
Boston, MA 02203
Telephone: (617) 565–9860
(AR, LA, MN,* OK, TX)
525 Griffin Street
Room 602
Dallas, TX 75202
Telephone: (214) 767–4731
Region II
Region VII
(NJ,* NY,* PR,* VI*)
201 Varick Street
Room 670
New York, NY 10014
Telephone: (212) 337–2378
(IA,* KS, MO, NE)
City Center Square
1100 Main Street, Suite 800
Kansas City, MO 64105
Telephone: (816) 426–5861
Region III
Region VIII
(DC, DE, MD,* PA, VA,* WV)
The Curtis Center —Suite 740 West
170 S. Independence Mall West
Philadelphia, PA 19106-3309
Telephone: (215) 861–4900
(CO, MT, ND, SD, UT,* WY*)
1999 Broadway
Suite 1690
Denver, CO 80802-5716
Telephone: (303) 844–1600
Region IV
Region IX
(AL, FL, GA, KY,* MS, NC,*
SC,* TN*)
Atlanta Federal Center
61 Forsyth Street, SW, Room 6T50
Atlanta, GA 30303
Telephone: (404) 562–2300
(American Samoa, AZ,* CA,*
Guam, HI,* NV,*
Commonwealth of the
Northern Mariana Islands)
71 Stevenson Street
4th Floor
San Francisco, CA 94105
Telephone: (415) 975–4310
Region V
(IL, IN,* MI,* MN,* OH, WI)
230 South Dearborn Street
Room 3244
Chicago, IL 60604
Telephone: (312) 353–2220
Region X
(AK,* ID, OR,* WA*)
1111 Third Avenue
Suite 715
Seattle, WA 98101-3212
Telephone: (206) 553–5930
* These states and territories operate their own OSHA-approved job safety
and health programs (Connecticut, New Jersey, and New York plans cover
public employees only). States with approved programs must have a
standard that is identical to, or at least as effective as, the federal standard.
32
Control of Hazardous Energy (Lockout/Tagout)
OSHA Area Offices
Anchorage, AK
(907) 271–5152
Birmingham, AL
(205) 731–1534
Mobile, AL
(334) 441–6131
Little Rock, AR
(501) 324–6291 (5818)
Phoenix, AZ
(602) 640–2348
Sacramento, CA
(916) 566–7471
San Diego, CA
(619) 557–5909
Denver, CO
(303) 844–5285
Englewood, CO
(303) 843–4500
Bridgeport, CT
(203) 579–5581
Hartford, CT
(860) 240–3152
Wilmington, DE
(302) 573–6518
Fort Lauderdale, FL
(954) 424–0242
Jacksonville, FL
(904) 232–2895
Tampa, FL
(813) 626–1177
Savannah, GA
(912) 652–4393
Smyrna, GA
(770) 984–8700
OSHA Regional and Area Offices
Tucker, GA
(770) 493–6644/6742/8419
Des Moines, IA
(515) 284–4794
Boise, ID
(208) 321–2960
Calumet City, IL
(708) 891–3800
Des Plaines, IL
(847) 803–4800
Fairview Heights, IL
(618) 632–8612
North Aurora, IL
(630) 896–8700
Peoria, IL
(309) 671–7033
Indianapolis, IN
(317) 226–7290
Wichita, KS
(316) 269–6644
Frankfort, KY
(502) 227–7024
Baton Rouge, LA
(225) 389–0474 (0431)
Braintree, MA
(617) 565–6924
Methuen, MA
(617) 565–8110
Springfield, MA
(413) 785–0123
Linthicum, MD
(410) 865–2055/2056
Augusta, ME
(207) 622–8417
33
Bangor, ME
(207) 941–8177
Portland, ME
(207) 780–3178
Lansing, MI
(517) 327–0904
Minneapolis, MN
(612) 664–5460
Kansas City, MO
(816) 483–9531
St. Louis, MO
(314) 425–4289
Jackson, MS
(601) 965–4606
Billings, MT
(406) 247–7494
Raleigh, NC
(919) 856–4770
Bismark, ND
(701) 250–4521
Omaha, NE
(402) 221–3182
Concord, NH
(603) 225–1629
Avenel, NJ
(732) 750–3270
Hasbrouck Heights, NJ
(201) 288–1700
Marlton, NJ
(609) 757–5181
Parsippany, NJ
(973) 263–1003
Albuquerque, NM
(505) 248–5302
34
Carson City, NV
(775) 885–6963
Albany, NY
(518) 464–4338
Bayside, NY
(718) 279–9060
Bowmansville, NY
(716) 684–3891
New York, NY
(212) 466–2482
North Syracuse, NY
(315) 451–0808
Tarrytown, NY
(914) 524–7510
Westbury, NY
(516) 334–3344
Cincinnati, OH
(513) 841–4132
Cleveland, OH
(216) 522–3818
Columbus, OH
(614) 469–5582
Toledo, OH
(419) 259–7542
Oklahoma City, OK
(405) 231–5351 (5389)
Portland, OR
(503) 326–2251
Allentown, PA
(610) 776–0592
Erie, PA
(814) 833–5758
Harrisburg, PA
(717) 782–3902
Control of Hazardous Energy (Lockout/Tagout)
Philadelphia, PA
(215) 597–4955
Pittsburgh, PA
(412) 395–4903
Wilkes–Barre, PA
(570) 826–6538
Guaynabo, PR
(787) 277–1560
Providence, RI
(401) 528–4669
Columbia, SC
(803) 765–5904
Nashville, TN
(615) 781–5423
Austin, TX
(512) 916–5783 (5788)
Corpus Christi, TX
(512) 888–3420
Dallas, TX
(214) 320–2400 (2558)
El Paso, TX
(915) 534–6251
Fort Worth, TX
(817) 428–2470 (485–7647)
OSHA Regional and Area Offices
Houston, TX
(281) 591–2438 (2787)
Houston, TX
(281) 286–0583/0584 (5922)
Lubbock, TX
(806) 472–7681 (7685)
Salt Lake City, UT
(801) 530–6901
Norfolk, VA
(757) 441–3820
Bellevue, WA
(206) 553–7520
Appleton, WI
(920) 734–4521
Eau Claire, WI
(715) 832–9019
Madison, WI
(608) 264–5388
Milwaukee, WI
(414) 297–3315
Charleston, WV
(304) 347–5937
35
OSHA Consultation Projects
Anchorage, AK
(907) 269–4957
Tuscaloosa, AL
(205) 348–3033
Little Rock, AR
(501) 682–4522
Phoenix, AZ
(602) 542–1695
Sacramento, CA
(916) 574–2555
Fort Collins, CO
(970) 491–6151
Wethersfield, CT
(860) 566–4550
Washington, DC
(202) 541–3727
Wilmington, DE
(302) 761–8219
Tampa, FL
(813) 974–9962
Atlanta, GA
(404) 894–2643
Tiyam, GU
9–1–(671) 475–1101
Honolulu, HI
(808) 586–9100
Des Moines, IA
(515) 281–7629
Boise, ID
(208) 426–3283
Chicago, IL
(312) 814–2337
Indianapolis, IN
(317) 232–2688
36
Topeka, KS
(785) 296–7476
Frankfort, KY
(502) 564–6895
Baton Rouge, LA
(225) 342–9601
West Newton, MA
(617) 727–3982
Laurel, MD
(410) 880–4970
Augusta, ME
(207) 624–6460
Lansing, MI
(517) 322–1809
Saint Paul, MN
(651) 297–2393
Jefferson City, MO
(573) 751–3403
Jackson, MS
(601) 987–3981
Helena, MT
(406) 444–6418
Raleigh, NC
(919) 807–2905
Bismarck, ND
(701) 328–5188
Lincoln, NE
(402) 471–4717
Concord, NH
(603) 271–2024
Trenton, NJ
(609) 292–3923
Santa Fe, NM
(505) 827–4230
Control of Hazardous Energy (Lockout/Tagout)
Albany, NY
(518) 457–2238
Henderson, NV
(702) 486–9140
Columbus, OH
(614) 644–2631
Oklahoma City, OK
(405) 528–1500
Salem, OR
(503) 378–3272
Indiana, PA
(724) 357–2396
Hato Rey, PR
(787) 754–2171
Providence, RI
(401) 222–2438
Columbia, SC
(803) 734–9614
Brookings, SD
(605) 688–4101
Nashville, TN
(615) 741–7036
OSHA Consultation Projects
Austin, TX
(512) 804–4640
Salt Lake City, UT
(801) 530–6901
Richmond, VA
(804) 786–6359
Christiansted St. Croix, VI
(809) 772–1315
Montepilier, VT
(802) 828–2765
Olympia, WA
(360) 902–5638
Madison, WI
(608) 266–9383
Waukesha, WI
(262) 523–3044
Charleston, WV
(304) 558–7890
Cheyenne, WY
(307) 777–7786
37
OSHA-Approved Safety and Health Plans
Juneau, AK
(907) 465–2700
Phoenix, AZ
(602) 542–5795
San Francisco, CA
(415) 703–5050
Wethersfield, CT
(860) 263–6505
Honolulu, HI
(808) 586–8844
Des Moines, IA
(515) 281–3447
Indianapolis, ID
(317) 232–2378
Indianapolis, IN
(317) 232–3325
Frankfort, KY
(502) 564–3070
Baltimore, MD
(410) 767–2215
Lansing, MI
(517) 322–1814
St. Paul, MN
(651) 284–5010
Raleigh, NC
(919) 807–2900
Trenton, NJ
(609) 292–2975
38
Santa Fe, NM
(505) 827–2850
Carson City, NV
(775) 684–7260
Salem, OR
(503) 378–3272
Hato Rey, PR
(787) 754–2119
Columbia, SC
(803) 896–4300
Nashville, TN
(615) 741–2582
Salt Lake City, UT
(801) 530–6901
Richmond, VA
(804) 786–2377
Christiansted, St. Croix, VI
(340) 773–1990
Montpelier VT
(802) 828–2288
Olympia, WA
(360) 902–4200
(360) 902–5430
Cheyenne, WY
(307) 777–7786
Control of Hazardous Energy (Lockout/Tagout)