IMPORTANT : READ BEFORE INSTALLATION
TO ENSURE PROPER INSTALLATION, FOLLOW STEPS CLOSELY
This software is protected by a license manager system. To use this software, a License File must be present.
The License File is locked to a specific computer or to a Computer ID Key (Hardware Device or Dongle). The
Software can be installed either on a single computer (i.e., "Standalone") or on a Network Server. If it is installed
on a Network Server, the license file determines how many users are supported.
(For NETWORK INSTALLATION see reverse)
SECTION BUILDER Version 8
Standalone Installation Instructions
If you have previously installed SECTION BUILDER version 8, make a backup copy of the
permanent license file “lservrc” before proceeding with this installation.
To Install the Program
1. Insert the CD into the CD drive and follow the installation
instructions.
2. When asked to do so, enter the serial number found on the
SECTION BUILDER CD jewel case.
A 30-day temporary license file is included with the package
for new users.
To Obtain a Permanent License File
Locked to a Computer:
1. Go to the installation directory and double click on "echoid.exe".
.
2. Copy the code number in the window to the locking Code
field at the bottom of Request For License Form.
Locked to a Computer ID Key:
1. You do not need to fill in the Locking Code number
Fax the completed Request for License Form to CSI
Existing users should copy the saved permanent license file
“lservrc” over the temporary one and skip the next step.
A license file will be emailed to you.
Copy that license file into the installation directory.
Computers and Structures, Inc.
1995 University Ave. Suite 540
Berkeley, CA 94704
Phone 510-845-2177
Fax 510-845-4096
www.csiberkeley.com
IMPORTANT : READ BEFORE INSTALLATION
TO ENSURE PROPER INSTALLATION, FOLLOW STEPS CLOSELY
This software is protected by a license manager system. To use this software, a License File must be present.
The License File is locked to a specific computer or to a Computer ID Key (Hardware Device or Dongle). The
Software can be installed either on a single computer (i.e., "Standalone") or on a Network Server. If it is installed
on a Network Server, the license file determines how many users are supported.
(For STANDALONEINSTALLATION see reverse)
SECTION BUILDER Version 8
Network Installation Instructions
In order to run SECTION BUILDER over a
network, you must complete steps A, B, & C.
To Obtain a Permanent License File
Locked to a Computer:
A. Install the SECTION BUILDER Server
Software on the server computer.
1. The communications protocol must be TCP/IP or Netware
IPX/SPX.
2. Insert the CD into the CD drive and follow the installation
instructions.
3. When asked to do so, enter the serial number found on the
SECTION BUILDER CD jewel case.
B. Install the License Manager Server
Software on the server computer
If you currently have Sentinel LM 7.2.0 Server running
go to step C.
1. Go to the License Manager directory located in the
SECTION BUILDER Server directory created in step A above.
2. Go to the License Manager\Server\Setup directory, double
click on "Setup.exe " and follow the instructions.
3. To register the temporary license file, double click on
" lslicense.bat " located in the SECTION BUILDER..\License
Manager folder.
A 30-day temporary license file for one user is included with the
package.
1. From the Server computer go to the License Manager directory in
the SECTION BUILDER installation directory and double click on
"echoid.exe". "echoid.exe" should be run from the actual
server and not the computer that you may have used to install the
program on the server.
2. Copy the code number in the window to the Locking Code field
at the bottom of the Request For License Form.
Locked to a Computer ID Key:
1. Complete the Request For License Form.
You do not need to fill in the Locking Code number.
Fax the completed Request For License Form to CSI
A license file with instructions will be emailed to you.
C. Install the SECTION BUILDER Workstation Software on each Client Computer
1. From each client workstation, go to the SECTION BUILDER
Server directory on the server, double click on "Setup.exe"
and follow the instructions.
SECTION BUILDER can now be run on the client workstations.
If SECTION BUILDER is slow in locating the server, (or can’t seem
to find the server), set the system Environment Variable
LSFORCEHOST on the workstation to the host name of the
License Manager Server computer. (You can run "Wechoid.exe"
from the server computer to find this host name.) Reboot the
worksation for the Environment Variable to take effect. Refer
to the License Manager System Administrator's Guide if you need
help on setting this variable in the Control Panel.
For more detailed information about the License Manager and the
License Manager Administration program "WlmAdmin", see the
License Manager System Administrator's Guide.