WORLDWIDE
ENGINEERING
STANDARDS
Material Specification
GMW3059
General
Restricted and Reportable Substances for Parts
GMW3034
1 Scope
QU 000001
This specification lists substances whose use in
materials and components, in the interests of
personnel and environmental safety, are either
prohibited or limited.
QU 000002
These restrictions are based on existing legislation
or self-imposed regulations.
QU 000005
The aim of this specification is to restrict/stop the
usage of the substances listed, to facilitate
compliance with current and future regulations.
VDA 232-101
1.1 Material Description. Not applicable.
1.1.1 Material Identification. Not applicable.
1.2 Cross-Reference of Replaced GMIO & NAO
Specifications.
Delta Motors
GM do Brasil
GM Holdens
HN 1000, Clause J
GM NAO
GM1000M
ISUZU
ITDC
QU 000000
SAAB
STD 3977
1.2.1 Specifications Qualified to this Material
Specification. Not applicable
1.3 Symbol. Not applicable
1.4 Typical Application. This specification applies to
materials and components specified by the
purchaser and for items where the design is held by
the supplier (black box).
2 References
Note: Only the latest approved standards are
applicable unless otherwise specified.
2.1 Normative.
ISO 11014
2.2 GM.
QU 000003
QU 000004
2.3 Additional.
3 Requirements
The list contained in this technical specification is
based on legal requirements and VDA 232-101 “VDA
List for Chemicals Subject to Declaration“ (from the
Association of German Automobile Manufacturers)“.
All substances that are listed in this standard in Table
1 and Table 2 that could exist in the product or could
be emitted from the product, must be declared.
Content limits are specified for all substances both
forbidden and requiring declaration. Unless otherwise
specified this limit amount is 0.1 % by mass for both
declared and forbidden materials. For amounts
below this limit a declaration is not required. This
percentage is to be calculated for the single
material/surface treatment level part, not the
assembly.
All substances in the list marked with an “F” are
forbidden above the reporting limit specified in the
table or 0.1% by mass if a limit is not listed. These
substances may be forbidden for all uses or for
specific applications due to legal or internal
regulations.
If technical requirements make the use of these
substances absolutely necessary, a deviation from
this regulation must be agreed upon between the
supplier and the responsible department at the
purchaser.
All substances in the list marked with “D“ must be
declared at levels above the limit noted in the table or
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 1 of 17
May 1998
GMW3059
GM WORLDWIDE ENGINEERING STANDARD
0.1% by mass if a limit is not given in the table. All
influences of their use for the specific application
shall be evaluated to achieve the highest possible
level of safety and environmental compatibility.
These substances must be replaced by other
substances, not listed herein, as soon as the
advance of technology, availability and economics
permit. Periodic reviews of the “D” listed items shall
be conducted, the frequency of which will be
established by the purchaser.
3.1 Requirements on Delivery. Independent of this
regulation, the supplier bears the responsibility for
ensuring that the materials and components
delivered meet the relevant legislations and
regulations of the countries to which it is supplied.
The requirements defined in this specification apply
according to clause 3.1.1 for all new materials and
components supplied, unless otherwise specified on
the drawing. These requirements also apply to resourced or re-designed materials and components.
3.1.1 Chemical Requirements. See Table 1 and
Table 2. The table is given in both alphabetical order
and by group (ie. metals, CFC’s, etc.), respectively.
Questions regarding the presence of these
substances can be resolved by using the test method
listed in the note column of Table 1 and Table 2 or by
testing metals by atomic absorption, organics by gas
chromatography, and fibers by polarized light
microscopy if no test method is listed.
3.1.2 Mechanical Requirements. Not applicable
3.1.3 Physical Requirements. Not applicable
3.1.4 Additional Requirements. This specification
requires the submission of data sheet 1 in Appendix
A. The substances and the materials/components
they are used in must be detailed. If the substance is
marked with an “F”, the form must be signed by the
department listed in the contact list for the Unit the
part is being supplied to. If the material/component
being supplied does not contain any of the
substances listed in Table 1 and Table 2, check the
appropriate box and submit the form as a declaration
of compliance to the unit contact as listed in the
address list. See also “Deviation”.
3.2 Processing Requirements.
were not applicable
Subparagraphs
3.3 Performance Requirements.
were not applicable
Subparagraphs
3.4 Requirements on other Stages during Life
Cycle. Subparagraphs were not applicable
4 Manufacturing Process
Not applicable
5 Rules and Regulations
5.1 Legal Regulations.
For
use
of
this
material/specification the valid laws and other
regulations and recommendations in the country of
usage have to be followed.
5.2 Language. In the event of any conflict between
the English and domestic language regarding this
document, the English language will take
precedence.
5.3 Restricted and Reportable Substances.
Not applicable
5.4 Inspection and Rejection. All shipments of
materials or parts under contract or purchase order
manufactured to this specification shall be equivalent
in every respect to the initial samples approved by
engineering. There shall be no changes in
formulation or manufacturing process permitted
without prior notification and approval by engineering.
Lack of notification by the supplier constitutes
grounds for rejection of any shipment. While samples
may be taken from incoming shipments and checked
for conformance to this specification, the supplier
shall accept the responsibility for incoming shipments
meeting this specification without dependence upon
purchaser’s inspection.
5.5 Initial Source Approval. No shipments shall be
made by any supplier until representative initial
production samples have been approved by
Materials Engineering as meeting the requirements
of this specification.
5.6 Safety Data Sheets. Completed copies of the
Material Safety Data Sheets meeting GM information
requirements, consistent with ISO 11014 standard
must be submitted with any new material
submissions or where a composition change has
occurred.
6 Approved Sources
Not applicable
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 2 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
GMW3059
Restricted and Reportable Substances for Parts per
GMW3059
7 Coding System
This material specification shall be given in other
documents, drawings, VTS, SSTS, CTS etc. as
follows:
8.2 Revisions.
8 Release and Revisions
8.1 Release. The specification was first approved
and released in May, 1998.
© Copyright March 1999 General Motors Corporation All Rights Reserved
May 1998
Page 3 of 17
GMW3059
GM WORLDWIDE ENGINEERING STANDARD
Table 1 - Restricted (F) and Reportable (D) Substances- List in Alphabetical Order
Substance
Acetamide
Acrylamide
Acrylonitrile
Actinolite
o-Aminoazotoluene Salts
Category
Acetamide
Acrylamide
Acrylonitrile
Fibers/Asbestos
Azo dye
CAS No.
000060-35-5
000079-06-1
000107-13-1
13768-00-8
Group
4-Aminobiphenyl
Aminobiphenyl, 4-
000092-67-1
D
4-Aminobiphenyl Salts
Azo dye
Group
F
2-Amino-4-nitrotoluene Salts
Azo dye
Group
F
Amosite
Aniline
Aniline Salts
Fibers/Asbestos
12172-73-5
F
Aniline
Aniline
Fibers/Asbestos
000062-53-3
Group
17068-78-9
D
D
F
Metals
Flame retardant
Metals
Metals
7440-36-0
001309-64-4
D
D
D
D > 400
ppm
Auramine
000492-80-8
D
metal refinement, metal adhesive, leather and
textile refinement, wood preservative, color
and melting coating
cotton
Metals
Metals
Group
D
D
pigments, additives in lubricants
Azo dye
000092-87-5
Benzidine Salts
Azo dye
Group
Benzo(a)anthracene
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
Metals
Metals
Flame retardants
CFC
000056-55-3
Group
Group
000353-59-3
D > 10
ppm
D > 10
ppm
D > 10
ppm
D > 10
ppm
D>1
ppm
D
D
D
F
CFC
000075-63-8
F
Butadiene
Phthalates
Metals
000106-99-0
000085-68-7
007440-43-9
Cadmium compounds
Metals
Group
Carbon Tetrachloride
CFC
Chloraniline
000056-23-5
Group
D
D
F > 75
ppm, D 
75 ppm
F > 75
ppm, D 
75 ppm
F
D
Azo dye
Group
Anthophylite
Antimony
Antimonous trioxide
Arsenic
Arsenic compounds
Auramine
Barium
Barium compounds except
Barium sulfate
Benzidine
Benzo(b)fluoranthene
Benzo(j)fluoranthene
Benzo(k)fluoranthene
Benzo(a)pyrene
Beryllium
Beryllium compounds
Brominated flame retardants
Bromochlorodifluoromethane
(Halon 1211)
Bromotrifluoromethane
(Halon 1301)
1,3-Butadiene
Butyl benzyl phthalate (BBP)
Cadmium
Chloraniline
p-Chloraniline Salts
Group
000205-99-2
000205-82-3
000207-08-9
000050-32-8
Rating Note
D
D
Will be F in the future.
D
QU 000004
F
F
Salt regulated with azo
dye
QU 000004
Example - occurrence
solvent admixture, softener stabilizer
residual monomer
residual monomer
friction lining, gaskets, insulation
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
friction lining, gaskets, insulation
dye
QU 000004
friction lining, gaskets, insulation
flame retardant
F > 100 Salt regulated with azo found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
ppm dye
found in textile and leather dyes, antioxidants,
F
F
Will be F in the future.
lubricants, rubbers, plastics
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
electronic parts
QU 000003
refrigerating or foaming agent, propellant
QU 000003
refrigerating or foaming agent, propellant
residual monomer
QU 000001 Only if
pigments, polymer stabilizer, surface
intentionally added for D protection of metals
QU 000001 Only if
pigments, polymer stabilizer, surface
intentionally added for D protection of metals
hardener or cross linkage agent for polymers
and epoxy resin
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 4 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
GMW3059
Chlorepoxypropane
(Epichlorohydrin)
Polychlorinated
compounds
Biocides
000106-89-8
D
residual monomer
Including
001336-36-3
1570-64-5
F
softener, impregnating agent, insulation liquid
D
Biocides
59-50-7
D
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
Flame retardant
338-65-8
338-64-7
75-68-3
000075-45-6
134190-53-7
110587-14-9
000593-70-4
134190-54-8
28987-04-4
Group
F
F
F
F
F
F
F
F
F
D
CFC
HCFC
HCFC
000076-15-3
108662-83-5
2837-89-0
F
F
F
HCFC
354-25-6
F
HCFC
Azo dye
134190-50-4
Group
F
F
HCFC
HCFC
HCFC
CFC
HCFC
Metals
Metals
431-07-2
75-88-7
421-04-5
000075-72-9
26588-23-8
007440-47-3
Group
F
F
F
F
F
D
D > 0.01
g/cm2
Fibers/Asbestos
12001-29-5
F
Metals
Colophony
007440-48-4
8050-09-7
D
D
Colophony (Rosin)
Copper
Metals
007440-50-8
D
Copper compounds
Metals
Group
D
Creosote
8001-58-9
D
Azo dye
Group
F
Fibers/Asbestos
1200-28-4
F
Azo dye
Group
F
Azo dye
Group
F
Benzo(a)pyrene
and other PAH
CFC
000053-70-3
Phthalates
Azo dye
000084-74-2
Group
D
F
HCFC
HCFC
431-06-1
471-43-2
F
F
Chlorepoxypropane
(Epichlorohydrin)
Chlorinated Biphenyl (PCB)
Chlorocresol (ortho-)
Chlorocresol (meta-)
2-Chloro-1,1-Difluoroethane
1-Chloro-1,2-Difluoroethane
1-Chloro-1,1-Difluoroethane
Chlorodifluoromethane (R22)
Chlorodifluoropropane
Chlorofluoroethane
Chlorofluoromethane (R31)
Chlorofluoropropane
Chlorohexafluoropropane
Chloroparaffin, unbranched,
(C10H22-nCln where n = 1 ... 8 to
C30H62-nCLn where n = 1 ... 28)
Chloropentafluoroethane (R115)
Chloropentafluoropropane
2-Chloro-1,1,1,2Tetrafluoroethane
1-Chloro-1,1,2,2Tetrafluoroethane
Chlorotetrafluoropropane
4-Chloro toluidine Salts
1-Chloro-1,2,2-Trifluoroethane
2-Chloro-1,1,1-Trifluoroethane
1-Chloro-1,1,2-Trifluoroethane
Chlorotrifluoromethane (R13)
Chlorotrifluoropropane
Chromium
Chromium(VI)-Salt
Chrysotile
Cobalt
Creosote
p-Cresidine Salts
Crocidolite
2,4-Diaminoanisol Salts
4,4'-Diaminodiphenyl-methane
Salts
Dibenz(a,h)anthracene
Dibromotetrafluoroethane
(Halon 2402)
Dibutylphthalate (DBP)
3,3'-Dichloro benzidine Salts
1,2-Dichloro-1,2-Difluoroethane
1,1-Dichloro-2,2-Difluoroethane
000124-73-2
QU 000003
refrigerating or foaming agent, propellant
QU 000003
refrigerating or foaming agent, propellant
flame retardant, plasticizer
QU 000003
refrigerating or foaming agent, propellant
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
QU 000003
refrigerating or foaming agent, propellant
Alloys exempt
Will be F Jan. 1, 2003
Test method:
GMW3034
QU 000004
alloying component
chrome pigments, surfaces chromed
friction lining, gaskets, insulation
alloy metal
Alloys, electronics, and
wiring exempt
Alloys, electronics, and stabilizer
wiring exempt
QU 000004
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
friction lining, gaskets, insulation
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
D > 10 Will be F in the future.
ppm
QU 000003
F
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
refrigerating or foaming agent, propellant
softener
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
© Copyright March 1999 General Motors Corporation All Rights Reserved
May 1998
Page 5 of 17
GMW3059
GM WORLDWIDE ENGINEERING STANDARD
1,2-Dichloro-1,1-Difluoroethane
Dichlorodifluoromethane (R12)
Dichlorodifluoropropane
1,2-Dichloro-1-Fluoroethane
1,1-Dichloro-2-Fluoroethane
1,1-Dichloro-1-Fluoroethane
Dichlorofluoromethane
Dichlorofluoropropane
Dichlorohexafluoropropane
(R216)
Dichloropentafluoropropane
Dichlorotetrafluoroethane (R114)
Dichlorotetrafluoroethane
Dichlorotetrafluoropropane
1,1-Dichloro-1,2,2,2-Tetrafluoroethane
2,2-Dichloro-1,1,1Trifluoroethane
Dichlorotrifluoropropane
Di-(2-ethylhexyl)phthalate
(DEHP)
Diethyl phthlate
1,1,-Difluoroethene (R1132a)
3,3'-Dimethoxy benzidine Salts
HCFC
CFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
CFC
1649-08-7
000075-71-8
134190-52-6
430-57-9
430-53-5
1717-00-6
00075-43-41
127404-11-9
000661-97-2
F
F
F
F
F
F
F
F
F
HCFC
CFC
CFC
HCFC
CFC
127564-92-5
000076-14-2
001320-37-2
127564-83-4
000374-07-2
F
F
F
F
F
HCFC
306-83-2
F
HCFC
Phthalates
116890-51-8
000117-81-7
F
D
Phthalates
CFC
Azo dye
000084-66-2
000075-38-7
Group
D
F
F
3,3'-Dimethylbenzidine Salts
Azo dye
Group
F
3,3'-Dimethyl-4,4'diaminodiphenylmethane Salts
Dimethyl phthalate
Di-n-octyl-phthalate (DOP)
Formaldehyde
Azo dye
Group
F
Phthalates
Phthalates
Biocides
000131-11-3
000117-84-0
000050-00-0
D
D
F
Glutaric aldehyde
Heptachlorofluoropropane (R211)
Hexachlorodifluoropropane
(R212)
Hexachlorofluoropropane
Isothiazolinones
Glutaric aldehyde
CFC
CFC
000113-30-8
D
F
F
HCFC
Biocide
F
D
Lead
Lead compounds, soluble in
water
Metals
Metals
29470-94-8
Including
26822-20-4
26172-55-4
007439-92-1
Group
Lead compounds, insoluble in
water
Mercury
Metals
Group
D
Metals
007439-97-6
076546-99-3
D
F
QU 000003
refrigerating or foaming agent, propellant
QU 000003
refrigerating or foaming agent, propellant
softener
QU 000003
refrigerating or foaming agent, propellant
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
QU 000002
biocide, adhesives, residues and fragments on
plastics
found in adhesives, paints, binders, varnishes
If uncertain about
solubility use test.....
soldering alloys
Example soluble compounds include lead
nitrate and lead acetate.
cable covering, corrosion protection,
pigments, additive for cathodic elpo process
cable covering, corrosion protection,
pigments, additive for cathodic elpo process
F > 10 Decision regarding
ppm exemption for lighting to
be made by each GM
Unit
pigments
Mercury compounds
Metals
Group
4,4'-Methylene-to (2-chloraniline)
Salts
Mineral fibres diameter <3µm,
length >5µm, l:d > 3:1 and other
respirable
Monochloroheptafluoropropane
(R217)
Monomethyldibromodiphenylmethane
Azo dye
Group
F > 10
ppm
F
Fibers/Asbestos
Group
D
Flame retardants
099688-47-8
F
residues and fragments during the
manufacture of polymers
Monomethyldichlorodiphenylmethane
Flame retardants
076253-60-6
F
residues and fragments during the
manufacture of polymers
CFC
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
friction lining, shielding, reinforcement,
insulation, cable
F
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 6 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
GMW3059
residues and fragments during the
manufacture of polymers
Monomethyltetrachlorodiphenylmethane
Naphthalene
2-Naphthylamine
Flame retardants
Naphthalene
Naphthylamine
000091-20-3
000091-59-8
D
F
2-Naphthylamine Salts
Azo dye
Group
F
Nickel
Nickel compounds
Metals
Metals
007440-02-0
Group
D
D
Alloys exempt
N-Nitrosodi-n-butylamine
N-Nitrosodiethanolamine
N-Nitrosodiethylamine
N-Nitrosodimethylamine
N-Nitrosodi-i-propylamine
N-Nitrosodi-n-propylamine
N-Nitrosoethylphenylamine
N-Nitrosomethylphenylamine
N-Nitrosomethylethylamine
N-Nitrosomorpholin
N-Nitrosopiperidine
N-Nitrosopyrrolidine
Nonylphenol (4-) NFO
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Phenol
D
D
D
D
D
D
D
D
D
D
D
D
D
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Nonylphenolethoxylates NFE
4,4'-Oxydianiline Salts
Phenol
Azo dye
000924-16-3
001116-54-7
000055-18-5
000062-75-9
000601-77-4
000621-64-7
000612-64-6
000614-00-6
010595-95-6
000059-89-2
000100-75-4
000930-55-2
104-40-5
25154-52-3
9016-45-9
Group
Pentachlorodifluoropropane
Pentachlorofluoroethane (R111)
Pentachlorofluoropropane
Pentachlorophenol (PCP)
Pentachlorophenol compounds
Pentachlorotrifluoropropane
(R213)
Phenol
HCFC
CFC
HCFC
Phenol
Phenol
CFC
116867-32-4
000354-56-3
134190-48-0
000087-86-5
Group
F
F
F
F
F
F
Phenol
000108-95-2
D
Phenols as a group
N-Phenyl-2-naphthylamine
Phenol
Phenyl-2naphthylamine
Flame retardants
Flame retardants
Group
000135-88-6
D
D
antioxidant
059536-65-1
F
F
additive in plastics and textiles
F
F
additive in plastics and textiles
softener, impregnating agent, insulation liquid
Polybromated Biphenyl (PBB)
Polybromated Diphenylether
(PBDE)
Polybromated Terphenyl
Flame retardants
Polychlorinated Terphenyl (PCT) Polychlorinated
compounds
PVC
Polyvinylchloride
F
Salt regulated with azo
dye
D
F
009002-86-2
D
Radioactive Compounds
Radioactive
Compounds
Sodium azide
Sodium azide
026628-22-8
D>
background
D
Sodium nitrite
Styrene
Styrene oxide
Tetrachlorodifluoroethane (R112)
1,1,1,2-Tetrachloro-2,2Difluoroethane
Tetrachlorodifluoropropane
1,1,2,2-Tetrachloro-1Fluoroethane
1,1,1,2-Tetrachloro-2Fluoroethane
Sodium nitrile
Styrene
Styrene
CFC
CFC
7623-00-0
000100-42-5
000096-09-3
000076-12-0
000076-11-9
D
D
D
F
F
HCFC
HCFC
127564-82-3
354-14-3
F
F
HCFC
354-11-0
F
textile additive
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
nickel pigment, galvanic additive, bonderize
additive
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
wood preservative
wood preservative
QU 000005
residual monomer in phenolic resins,
fragments on polymer materials, wood
materials and textiles
PVC as a minority
constituent in other
polymers only
gas generator airbag
QU 000003
residual monomer, solvent
residual monomer, softener
refrigerating or foaming agent, propellant
© Copyright March 1999 General Motors Corporation All Rights Reserved
May 1998
Page 7 of 17
GMW3059
GM WORLDWIDE ENGINEERING STANDARD
Tetrachlorofluoropropane
Tetrachlorotetrafluoropropane
(R214)
Tetrachlorotrifluoropropane
4,4'-Thiodianiline Salts
HCFC
CFC
134190-49-1
002268-46-4
F
F
HCFC
Azo dye
29470-95-9
Group
F
F
Thallium
Thallium compounds
Thiram (TMTD)
Tin organic compounds
m-Toluidine
o-Toluidine
p-Toluidine
o-Toluidine Salts
Metals
Metals
Flame retardants
Metals
Azo dye
Azo dye
Azo dye
Azo dye
007440-28-0
Group
137-26-8
Group
000108-44-1
000095-53-4
000106-49-0
Group
D
D
D
D
D
D
D
F
2,4-Toluylendiamine salts
Azo dye
Group
F
Fibers/Asbestos
14567-73-8
F
HCFC
354-21-2
F
HCFC
354-15-4
F
HCFC
CFC
CFC
HCFC
HCFC
HCFC
CFC
HCFC
CFC
127564-90-3
000071-55-6
000079-00-5
359-28-4
811-95-0
2366-36-1
000075-69-4
134190-51-5
004259-43-2
F
F
F
F
F
F
F
F
F
HCFC
CFC
CFC
127564-91-4
000076-13-1
026523-64-8
F
F
F
HCFC
CFC
Azo dye
61623-04-9
000354-58-5
Group
F
F
F
Flame retardants
Flame retardants
Vinylchloride
Vinylchloride
000512-56-1
115-86-6
000075-35-4
000075-01-4
D
D
F
F
Tremolite
1,2,2-Trichloro-1,1Difluoroethane
1,2,2-Trichloro-1,2Difluoroethane
Trichlorodifluoropropane
1,1,1-Trichloroethane
1,1,2- or 1,2,2-Trichloroethane
1,1,2-Trichloro-2-Flouroethane
1,1,2-Trichloro-1-Flouroethane
1,1,1-Trichloro-2-Flouroethane
Trichlorofluoromethane (R11)
Trichlorofluoropropane
Trichloropentafluoropropane
(R215)
Trichlorotetrafluoropropane
Trichlorotrifluoroethane (R113)
1,1,1-Trichloro-2,2,2-Trifluoro
ethane
Trichlorotrifluoropropane
1,1,1-Trifluorotrichloroethane
2,4,5-Trimethylaniline Salts
Trimethylphosphate
Triphenylphosphate
Vinylidene chloride
Vinylchloride monomer
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
electronic parts, sensor, alloying components
QU 000004
catalyst for PUR foams, stabilizer
dye, textile auxiliary, curing agent
dye, textile auxiliary, curing agent
dye, textile auxiliary, curing agent
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
friction lining, gaskets, insulation
QU 000003
refrigerating or foaming agent, propellant
QU 000003
refrigerating or foaming agent, propellant
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
flame retardant
residual monomer
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 8 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
GMW3059
Table 2 - Restricted (F) and Reportable (D) Substances - List by Category
Substance
Acetamide
Acrylamide
Acrylonitrile
4-Aminobiphenyl
Category
Acetamide
Acrylamide
Acrylonitrile
Aminobiphenyl, 4-
CAS No.
000060-35-5
000079-06-1
000107-13-1
000092-67-1
Rating Note
D
D
Will be F in the future.
D
Salt regulated with azo
D
Aniline
Aniline Salts
Aniline
Aniline
Auramine
000062-53-3
Group
000492-80-8
D
D
D
Auramine
2,4,5-Trimethylaniline Salts
Azo dye
Group
F
2,4-Diaminoanisol Salts
Azo dye
Group
F
2,4-Toluylendiamine salts
Azo dye
Group
F
2-Amino-4-nitrotoluene Salts
Azo dye
Group
F
3,3'-Dichloro benzidine Salts
Azo dye
Group
F
3,3'-Dimethoxy benzidine Salts
Azo dye
Group
F
3,3'-Dimethyl-4,4'diaminodiphenylmethane Salts
3,3'-Dimethylbenzidine Salts
Azo dye
Group
F
Azo dye
Group
F
4,4'-Diaminodiphenyl-methane
Azo dye
Salts
4,4'-Methylene-to (2-chloraniline) Azo dye
Salts
4,4'-Oxydianiline Salts
Azo dye
Group
F
Group
F
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
Group
F
4,4'-Thiodianiline Salts
Azo dye
Group
F
4-Aminobiphenyl Salts
Azo dye
Group
F
4-Chloro toluidine Salts
Azo dye
Group
F
Benzidine
Azo dye
000092-87-5
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
m-Toluidine
o-Aminoazotoluene Salts
Azo dye
Azo dye
000108-44-1
Group
o-Toluidine
o-Toluidine Salts
Azo dye
Azo dye
000095-53-4
Group
D
F
p-Chloraniline Salts
Azo dye
Group
F
p-Cresidine Salts
Azo dye
Group
F
p-Toluidine
2-Naphthylamine Salts
Azo dye
Azo dye
000106-49-0
Group
D
F
Benzidine Salts
Azo dye
Group
F
Benzo(a)anthracene
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
Benzo(a)pyrene
and other PAH
000056-55-3
dye
Benzo(a)pyrene
Benzo(b)fluoranthene
Benzo(j)fluoranthene
Benzo(k)fluoranthene
000050-32-8
000205-99-2
000205-82-3
000207-08-9
Example - occurrence
solvent admixture, softener stabilizer
residual monomer
residual monomer
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
dye
cotton
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
F > 100 Salt regulated with azo
ppm dye
dye, textile auxiliary, curing agent
D
found in textile and leather dyes, antioxidants,
F
D > 10
ppm
D>1
ppm
D > 10
ppm
D > 10
ppm
D > 10
ppm
Will be F in the future.
lubricants, rubbers, plastics
dye, textile auxiliary, curing agent
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
dye, textile auxiliary, curing agent
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
Will be F in the future.
bituminous coal tar, mineral oil, bitumen,
softener oil
© Copyright March 1999 General Motors Corporation All Rights Reserved
May 1998
Page 9 of 17
GMW3059
Dibenz(a,h)anthracene
Isothiazolinones
GM WORLDWIDE ENGINEERING STANDARD
Benzo(a)pyrene
and other PAH
Biocide
000053-70-3
D > 10 Will be F in the future.
ppm
D
bituminous coal tar, mineral oil, bitumen,
softener oil
found in adhesives, paints, binders, varnishes
Biocides
Including
26822-20-4
26172-55-4
1570-64-5
Biocides
59-50-7
D
Biocides
000050-00-0
F
QU 000002
Butadiene
CFC
CFC
000106-99-0
000075-38-7
000076-11-9
D
F
F
QU 000003
biocide, adhesives, residues and fragments on
plastics
residual monomer
refrigerating or foaming agent, propellant
CFC
026523-64-8
F
CFC
CFC
CFC
CFC
000071-55-6
000354-58-5
000079-00-5
000374-07-2
F
F
F
F
CFC
000353-59-3
F
QU 000003
refrigerating or foaming agent, propellant
CFC
000075-63-8
F
QU 000003
refrigerating or foaming agent, propellant
CFC
CFC
CFC
CFC
000056-23-5
000076-15-3
000075-72-9
000124-73-2
F
F
F
F
QU 000003
QU 000003
QU 000003
refrigerating or foaming agent, propellant
refrigerating or foaming agent, propellant
refrigerating or foaming agent, propellant
CFC
CFC
000075-71-8
000661-97-2
F
F
QU 000003
refrigerating or foaming agent, propellant
CFC
CFC
CFC
CFC
001320-37-2
000076-14-2
F
F
F
F
QU 000003
refrigerating or foaming agent, propellant
D
Chlorocresol (ortho-)
Chlorocresol (meta-)
Formaldehyde
1,3-Butadiene
1,1,-Difluoroethene (R1132a)
1,1,1,2-Tetrachloro-2,2Difluoroethane
1,1,1-Trichloro-2,2,2-Trifluoroethane
1,1,1-Trichloroethane
1,1,1-Trifluorotrichloroethane
1,1,2- or 1,2,2-Trichloroethane
1,1-Dichloro-1,2,2,2-Tetrafluoro
ethane
Bromochlorodifluoromethane
(Halon 1211)
Bromotrifluoromethane
(Halon 1301)
Carbon Tetrachloride
Chloropentafluoroethane (R115)
Chlorotrifluoromethane (R13)
Dibromotetrafluoroethane
(Halon 2402)
Dichlorodifluoromethane (R12)
Dichlorohexafluoropropane
(R216)
Dichlorotetrafluoroethane
Dichlorotetrafluoroethane (R114)
Heptachlorofluoropropane (R211)
Hexachlorodifluoropropane
(R212)
Monochloroheptafluoropropane
(R217)
Pentachlorofluoroethane (R111)
Pentachlorotrifluoropropane
(R213)
Tetrachlorodifluoroethane (R112)
Tetrachlorotetrafluoropropane
(R214)
Trichlorofluoromethane (R11)
Trichloropentafluoropropane
(R215)
Trichlorotrifluoroethane (R113)
076546-99-3
CFC
F
CFC
CFC
000354-56-3
F
F
CFC
CFC
000076-12-0
002268-46-4
F
F
QU 000003
refrigerating or foaming agent, propellant
CFC
CFC
000075-69-4
004259-43-2
F
F
QU 000003
refrigerating or foaming agent, propellant
CFC
Chloraniline
000076-13-1
Group
F
D
QU 000003
refrigerating or foaming agent, propellant
hardener or cross linkage agent for polymers
and epoxy resin
Chlorepoxypropane 000106-89-8
(Epichlorohydrin)
Colophony
8050-09-7
D
Creosote
8001-58-9
D
Amosite
Fibers/Asbestos
Fibers/Asbestos
13768-00-8
12172-73-5
F
F
QU 000004
QU 000004
friction lining, gaskets, insulation
friction lining, gaskets, insulation
Anthophylite
Fibers/Asbestos
17068-78-9
F
QU 000004
friction lining, gaskets, insulation
Fibers/Asbestos
12001-29-5
F
QU 000004
friction lining, gaskets, insulation
Chloraniline
Chlorepoxypropane
(Epichlorohydrin)
residual monomer
D
Colophony (Rosin)
Creosote
Actinolite
Chrysotile
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 10 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
Crocidolite
Mineral fibres diameter <3µm,
length >5µm, l:d > 3:1 and other
respirable
Tremolite
Brominated flame retardants
Monomethyldibromodiphenylmethane
Monomethyldichlorodiphenylmethane
Monomethyltetrachlorodiphenylmethane
Polybromated Biphenyl (PBB)
Polybromated Diphenylether
(PBDE)
Polybromated Terphenyl
Thiram (TMTD)
Trimethylphosphate
Triphenylphosphate
Antimonous trioxide
Chloroparaffin, unbranched,
(C10H22-nCln where n = 1 ... 8 to
C30H62-nCLn where n = 1 ... 28)
Glutaric aldehyde
1,1,1,2-Tetrachloro-2Fluoroethane
1,1,1-Trichloro-2-Flouroethane
1,1,2,2-Tetrachloro-1Fluoroethane
1,1,2-Trichloro-1-Flouroethane
1,1,2-Trichloro-2-Flouroethane
1,1-Dichloro-1-Fluoroethane
1,1-Dichloro-2,2-Difluoroethane
1,1-Dichloro-2-Fluoroethane
1,2,2-Trichloro-1,1Difluoroethane
1,2,2-Trichloro-1,2Difluoroethane
1,2-Dichloro-1,1-Difluoroethane
1,2-Dichloro-1,2-Difluoroethane
1,2-Dichloro-1-Fluoroethane
1-Chloro-1,1,2,2Tetrafluoroethane
1-Chloro-1,1,2-Trifluoroethane
1-Chloro-1,1-Difluoroethane
1-Chloro-1,2,2-Trifluoroethane
1-Chloro-1,2-Difluoroethane
2,2-Dichloro-1,1,1Trifluoroethane
2-Chloro-1,1,1,2Tetrafluoroethane
2-Chloro-1,1,1-Trifluoroethane
2-Chloro-1,1-Difluoroethane
Chlorodifluoromethane (R22)
Chlorodifluoropropane
Chlorofluoroethane
Chlorofluoromethane (R31)
Chlorofluoropropane
Chlorohexafluoropropane
Chloropentafluoropropane
Chlorotetrafluoropropane
GMW3059
QU 000004
friction lining, gaskets, insulation
Fibers/Asbestos
1200-28-4
F
Fibers/Asbestos
Group
D
Fibers/Asbestos
14567-73-8
F
Flame retardants
Flame retardants
Group
099688-47-8
D
F
Flame retardants
076253-60-6
F
residues and fragments during the
manufacture of polymers
F
residues and fragments during the
manufacture of polymers
Flame retardants
Flame retardants
Flame retardants
059536-65-1
friction lining, shielding, reinforcement,
insulation, cable
QU 000004
residues and fragments during the
manufacture of polymers
F
F
Flame retardants
Flame retardants
Flame retardants
Flame retardants
Flame retardants
Flame retardants
137-26-8
000512-56-1
115-86-6
001309-64-4
Group
F
D
D
D
D
D
Glutaric aldehyde
HCFC
000113-30-8
354-11-0
D
F
HCFC
HCFC
2366-36-1
354-14-3
F
F
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
811-95-0
359-28-4
1717-00-6
471-43-2
430-53-5
354-21-2
F
F
F
F
F
F
HCFC
354-15-4
F
HCFC
HCFC
HCFC
HCFC
1649-08-7
431-06-1
430-57-9
354-25-6
F
F
F
F
HCFC
HCFC
HCFC
HCFC
HCFC
421-04-5
75-68-3
431-07-2
338-64-7
306-83-2
F
F
F
F
F
HCFC
2837-89-0
F
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
75-88-7
338-65-8
000075-45-6
134190-53-7
110587-14-9
000593-70-4
134190-54-8
28987-04-4
108662-83-5
134190-50-4
F
F
F
F
F
F
F
F
F
F
friction lining, gaskets, insulation
additive in plastics and textiles
additive in plastics and textiles
flame retardant
flame retardant
flame retardant, plasticizer
QU 000003
refrigerating or foaming agent, propellant
QU 000003
refrigerating or foaming agent, propellant
© Copyright March 1999 General Motors Corporation All Rights Reserved
May 1998
Page 11 of 17
GMW3059
GM WORLDWIDE ENGINEERING STANDARD
Chlorotrifluoropropane
Dichlorodifluoropropane
Dichlorofluoromethane
Dichlorofluoropropane
Dichloropentafluoropropane
Dichlorotetrafluoropropane
Dichlorotrifluoropropane
Hexachlorofluoropropane
Pentachlorodifluoropropane
Pentachlorofluoropropane
Tetrachlorodifluoropropane
Tetrachlorofluoropropane
Tetrachlorotrifluoropropane
Trichlorodifluoropropane
Trichlorofluoropropane
Trichlorotetrafluoropropane
Trichlorotrifluoropropane
Antimony
Arsenic
Arsenic compounds
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
HCFC
Metals
Metals
Metals
26588-23-8
134190-52-6
00075-43-41
127404-11-9
127564-92-5
127564-83-4
116890-51-8
29470-94-8
116867-32-4
134190-48-0
127564-82-3
134190-49-1
29470-95-9
127564-90-3
134190-51-5
127564-91-4
61623-04-9
7440-36-0
Barium
Barium compounds except
Barium sulfate
Beryllium
Beryllium compounds
Cadmium
Metals
Metals
Group
Metals
Metals
Metals
Group
007440-43-9
Cadmium compounds
Metals
Group
Chromium
Chromium(VI)-Salt
Metals
Metals
007440-47-3
Group
Cobalt
Copper
Metals
Metals
007440-48-4
007440-50-8
D
D
Copper compounds
Metals
Group
D
Lead
Lead compounds, insoluble in
water
Lead compounds, soluble in
water
Metals
Metals
007439-92-1
Group
D
D
Metals
Group
F
Mercury
Metals
007439-97-6
Group
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
D
D
D > 400
ppm
metal refinement, metal adhesive, leather and
textile refinement, wood preservative, color
and melting coating
D
D
D
D
F > 75
ppm, D 
75 ppm
F > 75
ppm, D 
75 ppm
D
D > 0.01
g/cm2
pigments, additives in lubricants
electronic parts
QU 000001 Only if
pigments, polymer stabilizer, surface
intentionally added for D protection of metals
QU 000001 Only if
pigments, polymer stabilizer, surface
intentionally added for D protection of metals
Alloys exempt
Will be F Jan. 1, 2003
Test method:
GMW3034
alloying component
chrome pigments, surfaces chromed
alloy metal
Alloys, electronics, and
wiring exempt
Alloys, electronics, and stabilizer
wiring exempt
soldering alloys
cable covering, corrosion protection,
pigments, additive for cathodic elpo process
If uncertain about
solubility use test.....
Example soluble compounds include lead
nitrate and lead acetate.
cable covering, corrosion protection,
pigments, additive for cathodic elpo process
F > 10 Decision regarding
ppm exemption for lighting to
be made by each GM
Unit
Mercury compounds
Metals
Group
F > 10
ppm
Alloys exempt
D
D
Nickel
Nickel compounds
Metals
Metals
007440-02-0
Group
Thallium
Thallium compounds
Tin organic compounds
Naphthalene
2-Naphthylamine
Metals
Metals
Metals
Naphthalene
Naphthylamine
007440-28-0
Group
Group
000091-20-3
000091-59-8
D
D
D
D
F
N-Nitrosodi-i-propylamine
N-Nitrosodi-n-butylamine
Nitrosamine
Nitrosamine
000601-77-4
000924-16-3
D
D
Salt regulated with azo
dye
Will be F in the future.
Will be F in the future.
pigments
nickel pigment, galvanic additive, bonderize
additive
electronic parts, sensor, alloying components
catalyst for PUR foams, stabilizer
textile additive
found in textile and leather dyes, antioxidants,
lubricants, rubbers, plastics
rubber article
rubber article
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 12 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
N-Nitrosodi-n-propylamine
N-Nitrosodiethanolamine
N-Nitrosodiethylamine
N-Nitrosodimethylamine
N-Nitrosoethylphenylamine
N-Nitrosomethylethylamine
N-Nitrosomethylphenylamine
N-Nitrosomorpholin
N-Nitrosopiperidine
N-Nitrosopyrrolidine
Nonylphenol (4-) NFO
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Nitrosamine
Phenol
Nonylphenolethoxylates NFE
Pentachlorophenol (PCP)
Pentachlorophenol compounds
Phenol
Phenol
Phenol
Phenol
Phenol
Phenols as a group
N-Phenyl-2-naphthylamine
Phenol
Phenyl-2naphthylamine
Phthalates
Phthalates
Butyl benzyl phthalate (BBP)
Di-(2-ethylhexyl)phthalate
(DEHP)
Di-n-octyl-phthalate (DOP)
Dibutylphthalate (DBP)
Diethyl phthlate
Dimethyl phthalate
Chlorinated Biphenyl (PCB)
Phthalates
Phthalates
Phthalates
Phthalates
Polychlorinated
compounds
Polychlorinated Terphenyl (PCT) Polychlorinated
compounds
PVC
Polyvinylchloride
GMW3059
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
Will be F in the future.
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
rubber article
QU 000005
wood preservative
wood preservative
residual monomer in phenolic resins,
fragments on polymer materials, wood
materials and textiles
000621-64-7
001116-54-7
000055-18-5
000062-75-9
000612-64-6
010595-95-6
000614-00-6
000059-89-2
000100-75-4
000930-55-2
104-40-5
25154-52-3
9016-45-9
000087-86-5
Group
000108-95-2
D
D
D
D
D
D
D
D
D
D
D
Group
000135-88-6
D
D
antioxidant
000085-68-7
000117-81-7
D
D
softener
000117-84-0
000084-74-2
000084-66-2
000131-11-3
Including
001336-36-3
D
D
D
D
F
D
F
F
D
Will be F in the future.
softener, impregnating agent, insulation liquid
softener, impregnating agent, insulation liquid
F
009002-86-2
D
Radioactive Compounds
Radioactive
Compounds
Sodium azide
Sodium azide
026628-22-8
D>
background
D
Sodium nitrite
Styrene
Styrene oxide
Vinylchloride monomer
Vinylidene chloride
Sodium nitrile
Styrene
Styrene
Vinylchloride
Vinylchloride
7623-00-0
000100-42-5
000096-09-3
000075-01-4
000075-35-4
D
D
D
F
F
softener
PVC as a minority
constituent in other
polymers only
gas generator airbag
residual monomer, solvent
residual monomer, softener
residual monomer
© Copyright March 1999 General Motors Corporation All Rights Reserved
May 1998
Page 13 of 17
GMW3059
GM WORLDWIDE ENGINEERING STANDARD
Appendix A
Data Sheet 1
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 14 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
Instructions for Data Sheet 1
Data Sheet 1 is to be filled out for all parts. The form
should be mailed to each unit that the part is being
supplied to. If the part is being supplied to more than
one unit, for example NAO Car Group and Opel, the
form must be mailed to each unit.
A. Assembly (Asm)/Part Information: Title block Enter the information that identifies the part being
supplied into sections B-H.
B. Asm/Part Number: Enter the part identification
number assigned by the unit the part is being
supplied to.
C. Asm/Part Name: Enter the name of the part as
assigned by the unit the part is being supplied to.
D. Model Yr/Vehicle Line: Enter the model year of
the vehicle the part is being supplied for and the
name of the vehicle.
E. Asm/Part Revision Level and Rev. Date: Enter any
information that would identify what the most current
level of revision and what date that last revision
occurred.
F. Unit Supplied to: Enter the name of the
organization you are supplying the part to. A list of
units along with contact information for each is in the
appendix.
GMW3059
L. Department: Enter the department within the
supplier company that the contact belongs to.
M. Mail Code (if applicable): Enter internal mail code
if required within supplier company to get mail to the
contact person.
N. Address: Enter address (including country),
telephone number, and fax number for supplier.
O. Declaration section: Mark the applicable box. If
box 1 is marked proceed to section T sign and
submit form. If box 2 is marked proceed to section
P.
P. Component in Assembly: If there is more than one
component in the assembly/part being supplied enter
the part number, name, and mass of the specific
component that the reported substance is found in.
If there is more than one component that contains
the reported substance list all components that apply.
If there is more than one reported substance, list all
components that contain each substance.
Q. Material/Surface treatment: Enter the standard
number, name, and mass percentage of the material
or surface treatment that contains the restricted or
reported substance.
R. Substance: Enter the CAS number, name, and
mass percentage of the reported substance present
in the material/surface treatment listed in Q.
H. Comments: Enter any other information that would
help identify the part.
S. Purpose for Use and Plan to Eliminate Use
Including Timing and Substitute Substances: State
the reason this substance must be used. Also state
what plans are in place to eliminate the use of this
substance, by what date the use will be eliminated
and what the substitute substance will be.
I. Manufacturer/Supplier Information: Title block Supplier enters their information in sections J-N.
T. Supplier Certification: Sign, print name and date
to certify all listed information is true and correct.
J. Name: Enter contact name at the supplier.
U. Unit Approval if “F” Substances Present: If the
substance listed is a “F” substance the unit the part
is being supplied to must sign the form to approve
the use.
G. Asm/Part Mass: Enter the mass of the complete
assembly being supplied.
K. Company: Enter company name that is supplying
the part.
© Copyright March 1999 General Motors Corporation All Rights Reserved
May 1998
Page 15 of 17
GMW3059
GM WORLDWIDE ENGINEERING STANDARD
Address List
Unit Contact:
Unit:
Dept.:
Post-box/
mail code:
Location:
Mr./Mrs.:
Phone:
Fax:
Adam Opel AG
Holdens
GM NAO Car Group
ITDC, Central Laboratories
Central Laboratory
Materials Engineering
PKZ: 85-70
Mail Point 350
480-205-161
65423 Rüsselsheim
241 Salmon St
30007 VanDyke
Germany
Port Melbourne 3207
Warren, MI 48090
Australia
USA
Christine Haber
Phil Stirling
Jack Relyea
06142 / 771745
61 3 9647 1714
(810)492-1291
06142 / 774484
61 3 9647 1286
(810)492-6354
Saab
GM do Brasil Ltda
GM NAO Truck Group
Materials Technology
Materials Eng. - Chemical Lab.
CChemical Lab.
Unit Contact:
Unit:
Dept.:
Post-box/
mail code:
Location:
TVLEA 16-1
Cx. Postal 197
S-461 80 Trollhattan
Sao Caetano do Sul - SP
Sweden
CEP 09501 - 907
Brasil
Mr./Mrs.:
Phone:
Fax:
Cristina Nordstrom
Antonio Carlos Haddad
0520-84893
55 11 4234 7871
0520-78150
55 11 4234 7981
Unit Contact:
Unit:
Isuzu
Dept.:
Post-box/
mail code:
Location:
Mr./Mrs.:
Phone:
Fax:
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 16 of 17
May 1998
GM WORLDWIDE ENGINEERING STANDARD
Deviations
GMW3059
For parts being supplied to Saab, signatures are
required for all substances, both D and F.
© Copyright March 1999 General Motors Corporation All Rights Reserved
Page 17 of 17
May 1998