INSTALLATION AND
ADMINISTRATION
GUIDE
Cisco Small Business
Camera Accessories
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found
at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (1005R)
© 2010 Cisco Systems, Inc. All rights reserved.
78-19419-01B0
Contents
Chapter 1: About This Document
5
Before You Begin
5
Lens Specifications
6
Enclosure Specifications
7
Cisco PVC300 Enclosure Accessory Specifications
Warnings and Precautions
Statement 1071—Warning Definition
Where To Go Next
Chapter 2: Accessory Installation Processes
8
10
10
16
17
Installing a Lens
17
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
19
Before You Begin
19
Preparing the Enclosure
22
Preparing the Brackets
23
Connecting the Cables
23
Attaching the Camera to the Camera Platform
32
Building the Enclosure
33
Mounting the Enclosure
35
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
37
Before You Begin
37
Assembling the Enclosure
39
Securing the Power Adaptor
43
Where to Go Next
43
Installing the Cisco VC 032 Corner Mount Adapter
44
Installing the Cisco VC 033 Pole Mount Adapter
47
Installing the VC220 Cameras in a VC 025 Enclosure
50
Before You Begin
50
Preparing the Enclosure
50
Installing the Enclosure
53
Camera Accessories Installation and Administration Guide
3
Contents
Appendix A: Specifications
57
Cisco CAMLWA (Computar 1/3-inch 2.3 mm Wide Angle Lens)
57
Cisco CAMLMI (Tamron 1/3-inch 3-8 mm Varifocal 2.7X Zoom Lens)
58
Cisco VC 020 (Camera Exterior Enclosure with Heater and Blower for the
Cisco PVC2300/WVC2300)
58
Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the Cisco PVC300)60
Cisco VC 025 (Indoor Recessed Ceiling Mount Kit for the Cisco VC220) 62
Appendix B: Where to Go From Here
64
Camera Accessories Installation and Administration Guide
4
1
About This Document
The Cisco Small Business Internet Video Cameras provide high quality monitoring
that can be optimized for many different applications. This document describes
the installation of various camera accessories that can be used with the Cisco
PVC2300, WVC2300, and PVC300 cameras.
Before You Begin
This document assumes that you have previously installed and configured your
camera or cameras. For installation instructions, go to www.cisco.com/go/
smallbizcameras for the Quick Installation Guide or the Administration Guide for
your particular Cisco camera model. Datasheets are also available for your
cameras and accessories on the same website.
The following Cisco cameras can use the accessories described in this document:
•
PVC2300—Cisco Small Business Internet Video Camera with Audio and
POE
•
WVC2300—Cisco Small Business Wireless-G Internet Video Camera with
Audio
•
PVC300—Cisco Small Business PTZ Internet Camera with Audio and POE
•
VC220—Cisco VC220 Dome Wide Dynamic Range (WDR) Day/Night PoE
Network Camera
Please check www.cisco.com for compatibility if your camera is not included in
this list.
Camera Accessories Installation and Administration Guide
5
1
About This Document
Lens Specifications
Lens Specifications
The following lenses can be used with the Cisco PVC2300 and WVC2300
cameras:
Cisco Lens
Model Number
Camera Lens Description
CIVS-IPC-VT38
Tamron 3-8 mm Varifocal Lens, CS Mount
CIVS-IPC-VT31
Tamron 3-11 mm Varifocal Lens, CS Mount
CIVS-IPC-VT55
Tamron 5-50 mm Varifocal Lens, CS Mount
CIVS-IPC-VF38
Fujinon 3-8 mm Varifocal Lens, CS Mount
CIVS-IPC-VF31
Fujinon 3-11 mm Varifocal Lens, CS Mount
CIVS-IPC-VF55
Fujinon 5-50 mm Varifocal Lens, CS Mount
CAMLMI
Tamron 1/3-inch 3-8 mm Varifocal 2.7X Zoom Lens, CS
Mount. For installation instructions, see Installing a Lens,
page 17.
CAMLWA
Computar 1/3-inch 2.3 mm Wide Angle Lens. For installation
instructions, see Installing a Lens, page 17.
Camera Accessories Installation and Administration Guide
6
1
About This Document
Enclosure Specifications
Enclosure Specifications
The following enclosures can be used with the Cisco PVC2300, WVC2300,
PVC300, and VC220 IP cameras:
Cisco
Camera
Cisco
Enclosure
Model
Number
Enclosure Name
Description
PVC2300/
WVC2300
VC 020
Exterior Camera
Enclosure with
Defroster and
Blower
IP55 Certified outdoor enclosure
with defroster and blower
provides protection against small
particles and splashing water.
PVC300
VC 030
Camera
Enclosure
Exterior Pan Tilt
Dome enclosure with wallmounting bracket and power
adapter.
Camera Accessories Installation and Administration Guide
7
1
About This Document
Enclosure Specifications
Cisco
Camera
Cisco
Enclosure
Model
Number
Enclosure Name
Description
VC220
VC 025
Cisco VC 025
Indoor Ceiling
Mount Kit
Indoor recessed ceiling mount kit
specifically designed to work
with the Cisco VC220 Network
Camera. The recessed feature
reduces the area of the camera
body that is below the ceiling.
The cover is especially useful in
false ceiling applications.
NOTE: The three holes on the
front of the cover indicate the
microphone.
Cisco PVC300 Enclosure Accessory Specifications
The following items can be used with the VC 030 dome enclosure for the PVC300
camera:
Cisco VC 030
Accessory Model
Number
Accessory Name
Description
CAB-AC-C5-US=
Localized Power
Cord
A power cord is not included with the
VC 030 enclosure but is required for
operation. Select the appropriate
power cord based on regional
requirements.
CAB-AC-C5-UK=
CAB-AC-C5-EUR=
CAB-AC-C5-AUS=
Camera Accessories Installation and Administration Guide
8
1
About This Document
Enclosure Specifications
Cisco VC 030
Accessory Model
Number
Accessory Name
Description
VC 031
Camera Exterior
Pan Tilt Pendant
Mounting Adapter
Pendant mounting adapter for
VC 030 includes ceiling mount and
two pendant poles.
VC 032
Camera Exterior
Pan Tilt Corner
Mounting Adapter
Corner mount adapter used with the
VC 030 to mount the PVC300 on the
corner of a building.
VC 033
Camera Exterior
Pan Tilt Pole
Mounting Adapter
Pole mount adapter used with the
VC 030 to mount the PVC300 on a
pole.
NOTE Before installing a surveillance system, check with local government agencies to
determine if video surveillance and audio monitoring are permitted in your area.
Camera Accessories Installation and Administration Guide
9
About This Document
Warnings and Precautions
1
Warnings and Precautions
Statement 1071—Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Camera Accessories Installation and Administration Guide
10
About This Document
Warnings and Precautions
Warnung
1
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Camera Accessories Installation and Administration Guide
11
About This Document
Warnings and Precautions
Varning!
1
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Camera Accessories Installation and Administration Guide
12
About This Document
Warnings and Precautions
Aviso
1
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Camera Accessories Installation and Administration Guide
13
About This Document
Warnings and Precautions
Camera Accessories Installation and Administration Guide
1
14
1
About This Document
Warnings and Precautions
WARNING Only trained and qualified personnel should be allowed to install, replace, or
service this equipment. Statement 1030
WARNING No user-serviceable parts inside. Do not open. Statement 1073
Camera Accessories Installation and Administration Guide
15
1
About This Document
Where To Go Next
Where To Go Next
The installation process for lenses and enclosures are discussed in Accessory
Installation Processes, page 17.
Camera Accessories Installation and Administration Guide
16
2
Accessory Installation Processes
The following procedures help you install your Cisco camera accessories.
•
Installing a Lens, page 17
•
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure,
page 19
•
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure, page 37
•
Installing the Cisco VC 032 Corner Mount Adapter, page 44
•
Installing the Cisco VC 033 Pole Mount Adapter, page 47
•
Installing the VC220 Cameras in a VC 025 Enclosure, page 50
Installing a Lens
Follow the instructions below to replace the Cisco PVC2300 or WVC2300 camera
lens with any C- or CS-mount lens.
STEP 1 Unscrew the current lens on your Cisco PVC2300 or WVC2300 IP camera.
STEP 2 Ensure that the new lens is clean because any dirt may degrade the quality of
video images. Save the lens opening dust cap and replace the dust cap if you
remove the lens.
Camera Accessories Installation and Administration Guide
17
Accessory Installation Processes
Installing a Lens
2
STEP 3 Screw the new lens onto the opening of the camera. The camera accepts both C-
and CS-mount lenses.
•
If you are using a CS-mount lens, screw the lens into the lens opening.
•
If you are using the C-mount lens then you need to use the C-mount 5 mm
lens adapter ring. The adapter ring is included with the camera.
•
If you are using a DC auto iris lens, connect its cable to the DC auto iris lens
connector on the IP camera. The illustrations below show the location of the
connector on the IP camera.
STEP 4 If you have a manual iris lens, adjust the iris according to the prevailing light
conditions.
STEP 5 Adjust the focus of your lens. Turn the lens slowly either clockwise or
counterclockwise until the desired image appears. Do not turn the lens too far in
either direction.
Camera Accessories Installation and Administration Guide
18
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
Installing the PVC2300/WVC2300 Cameras in a VC 020
Enclosure
Follow the instructions below to install a Cisco PVC2300 or WVC2300 camera into
a Cisco VC 020 enclosure. Please note that the Cisco WVC2300 camera must be
wired to be used in the enclosure. Wireless mode is not supported.
Before You Begin
If you plan to install this camera into a tropical, coastal, saltwater, or corrosive
industrial water/moist environment, seal each stainless steel screw and fitting with
a silicon grease compound. This compound prevents corrosion and extends the
life span of the camera and the housing.
STEP 1 Organize the components of the VC 020 enclosure unit:
Camera Accessories Installation and Administration Guide
19
2
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
Included Parts
•
Enclosure cover and base
•
Wall mount bracket
•
Enclosure bracket
•
Two accessory kits, which includes the following:
Accessory Kit Parts, For Bracket
Number of Items
Anchor
3
Hexagonal stainless steel screws
3
Stainless steel washers
4
Nylon washers
4
L-type hex wrench
1
Allen wrench
1
Accessory Kit Parts, For Camera
Number of Items
Plastic pad
2
Plastic washer
1
Hexagonal stainless steel screw 1/4 x 3/8
1
Hexagonal stainless steel screw 1/4 x 1/2
1
Stainless washers
1
Required Tools and Parts (Not Included)
•
RJ45 plug
•
Wire stripper or RJ45 crimping tool
•
10 mm wrench or socket
•
Network cable tester
Camera Accessories Installation and Administration Guide
20
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
Optional Tools and Parts (Not Included)
•
Plastic pipe or conduit for protecting cords and cables
STEP 2 Familiarize yourself with the internal components of the enclosure.
STEP 3 Set up and focus your camera before placing it in the enclosure. When it is in the
enclosure, you can’t make any more adjustments. Refer to the PVC2300 and
WVC2300 Administration Guide for setup instructions.
NOTE The Cisco WVC2300 camera must be wired to be used in the enclosure. Wireless
mode is not supported.
Camera Accessories Installation and Administration Guide
21
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
Preparing the Enclosure
STEP 1 Use the provided wrench to remove the four screws that attach the enclosure
cover to the base.
STEP 2 Lift the enclosure cover off the base.
STEP 3 Use the provided wrench to release the four keyhole screws, then slide the
camera platform to withdraw it from the enclosure base.
STEP 4 Use the supplied L-type hex wrench to detach the rectangular support from the
camera platform. The rectangular support is required only during shipping.
Camera Accessories Installation and Administration Guide
22
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
Preparing the Brackets
This procedure describes how to connect the mounting bracket and the enclosure
bracket.
STEP 1 Using the L-type hex wrench, adjust the ball joint in the enclosure bracket to set
the approximate direction the enclosure.
STEP 2 Place the wall mount bracket and the enclosure bracket together.
STEP 3 Screw the brackets together using the provided stainless steel screw and L-type
hex wrench.
Connecting the Cables
Before completing this procedure, you must cut the camera’s Ethernet cable and
the power cord as it will be necessary to feed them through the mounting
brackets and the cable conduits found on the bottom of the enclosure.
WARNING Equipment connected to outdoor cameras must be permanently grounded in
accordance with national and local codes. Statement 374
WARNING Hazardous voltages may be present in the outdoor camera cables under fault
conditions. Disconnect all cables from the outdoor cameras before servicing this
equipment. Statement 376
WARNING Do not use this product near water; for example, near a bath tub, wash bowl, kitchen
sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035
WARNING Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations. Statement 1036
Camera Accessories Installation and Administration Guide
23
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
WARNING Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface. Statement 1037
WARNING Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning. Statement 1038
STEP 1 Feed the cut Ethernet cable and power cord through the brackets.
STEP 2 Feed the Ethernet cable and power cord through the conduits found on the bottom
of the enclosure. The power cord goes through the conduit closest to the power
supply wiring.
WARNING When stranded wiring is required, use approved wiring terminations, such as
closed-loop or spade-type with upturned lugs. These terminations should be the
appropriate size for the wires and should clamp both the insulation and conductor.
Statement 1002
WARNING Use copper conductors only. Statement 1025
Camera Accessories Installation and Administration Guide
24
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
STEP 3 Add the ferrite core on the power cord.
STEP 4 Add the ferrite core on the Ethernet cable.
Camera Accessories Installation and Administration Guide
25
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
STEP 5 Connect the power cord to the terminal block assembly. You can make these
connections in one of two ways: color matching the wires, or using a multimeter to
measure resistance from the power cord and the terminal block assembly.
WARNING This equipment has been designed for connection to TN and IT power systems.
Statement 1007
WARNING This equipment must be grounded. Never defeat the ground conductor or operate
the equipment in the absence of a suitably installed ground conductor. Contact the
appropriate electrical inspection authority or an electrician if you are uncertain that
suitable grounding is available. Statement 1024
WARNING When installing or replacing the unit, the ground connection must always be made
first and disconnected last. Statement 1046
WARNING Use copper conductors only. Statement 1025
WARNING The ground connection from the power cable MUST connect to the chassis first.
The power cord ground wire must connect to the chassis ground terminal first. A
closed loop connector must be attached to the ground and then attached to the
screw and lock washer at the protective earth ground (PE).
Camera Accessories Installation and Administration Guide
26
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
•
To color match the wires It is highly recommended that the installer
references an IEC standard wiring diagram, such as those found at
http://www.allaboutcircuits.com.
•
If you are using a multimeter, and you have a properly labeled power cord,
you can use the multimeter to register the resistance from the prongs. The
following is an illustration of a labeled European AC power cord plug head,
showing Live, Earth, Neutral.
•
If you are using a multimeter, the matched wire and plug will show
resistance; mismatched will read OL (overload). By testing, the labeled plug
pin on the cross-section indicates the exact wire, which you can then
directly match on the enclosure power block assembly. The following is an
illustration of a multimeter measuring the polarity of the wires.
Camera Accessories Installation and Administration Guide
27
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
•
2
The following illustration shows the power cord attaching to the terminal
block assembly. Note that the power cord ground wire (green/yellow in this
case) does not connect to the terminal block; the ground connects directly
to the chassis.
Camera Accessories Installation and Administration Guide
28
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
•
2
The following illustration shows the power cord ground wire (green/yellow
in this case) directly connecting to the enclosure chassis.
Camera Accessories Installation and Administration Guide
29
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
STEP 6 Prepare to clamp the Ethernet cable with an RJ45 plug. To make the proper
connections, refer to the following illustration that provides color mapping for the
cable wires.
STEP 7 Use the RJ45 crimping tool to clamp the plug to the wires.
STEP 8 Use a network cable tester to test the Ethernet connections.
Camera Accessories Installation and Administration Guide
30
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
STEP 9 Make any other I/O connections to the terminal block assembly (optional).
•
Pin 1, 2, 3 and 4 are DC 12C outputs for motor lenses, IR illuminators, sirens
or speakers
•
Pins 5 and 6 are DC12V outputs for cameras
NOTE If a pin is not in use, remove the cable from the connector.
Camera Accessories Installation and Administration Guide
31
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
Attaching the Camera to the Camera Platform
In this procedure, you will attach the camera to the camera platform in the
enclosure.
STEP 1 From the accessory kit, remove a rectangular plastic pad and a steel washer. The
pad and the washer are pictured below.
STEP 2 Turn the camera upside down and find the mounting hole.
STEP 3 Place the plastic pad over the mounting hole.
STEP 4 Remove the screw from the camera platform. Place the washer on top of the
camera platform, followed by the screw.
STEP 5 Align the screw holes of the camera and camera platform.
Camera Accessories Installation and Administration Guide
32
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
STEP 6 Use the supplied L-type hex wrench to secure the camera platform to the camera.
Building the Enclosure
STEP 1 Use the small wrench to secure the camera platform onto the enclosure base.
TIP
Make sure that the camera is firmly attached to the enclosure base and that the
camera is as close to the front (glass) of the enclosure as possible.
Camera Accessories Installation and Administration Guide
33
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
STEP 2 Connect the Ethernet cable and power cord to the camera.
STEP 3 Place the enclosure back over the sled and replace all screws.
Camera Accessories Installation and Administration Guide
34
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
Mounting the Enclosure
STEP 1 Use the rear section of the wall mount bracket (1) as a template to mark the
mounting holes on the wall.
STEP 2 Attach the main enclosure to the brackets with the supplied four 1/4-inch screws
(2).
Camera Accessories Installation and Administration Guide
35
Accessory Installation Processes
Installing the PVC2300/WVC2300 Cameras in a VC 020 Enclosure
2
STEP 3 Feed the cables from the enclosure and mounting brackets through the concealed
cable channel found underneath the wall mount bracket (3).
STEP 4 Secure the brackets and enclosure to the wall with the supplied plastic anchors
and screws.
STEP 5 Using the L-type hex wrench, adjust the ball joint in the enclosure bracket to set
the final direction of the enclosure (4).
STEP 6 (Optional) Plastic pipe or conduit should be used to waterproof and protect the
cables and cords.
Camera Accessories Installation and Administration Guide
36
Accessory Installation Processes
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
2
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
Follow the instructions below to install a Cisco PVC300 camera into a
Cisco VC 030 enclosure. These instructions also cover using the optional
Cisco VC 031 Pendant Mounting Adapter.
Before You Begin
If you plan to install this camera into a tropical, coastal, saltwater, or corrosive
industrial water/moist environment, seal each stainless steel screw and fitting with
a silicon grease compound. This compound prevents corrosion and extends the
life span of the camera and the housing.
STEP 1 Organize the following components of the VC 030 enclosure unit:
Included Parts
•
Enclosure
•
Enclosure cover
•
Wall mount bracket
•
Power supply
•
Camera cable
Camera Accessories Installation and Administration Guide
37
Accessory Installation Processes
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
•
2
Cross iron plate and screws
Required Tools and Parts (Not Included)
•
Phillips-head screwdriver
•
Power cord. See the Cisco PVC300 Enclosure Accessory Specifications
section for ordering information.
Optional Tools and Parts (Not Included)
•
Extension cord—Custom length, 2-core copper conductor, type SPT-1 (UL/
CSA style), 18 AWG, texture ≥ 2 x 0.824 mm², withstand 105° C, and 300V
•
Electrical Junction Box— Protection level IP66 or above; inner size at least
W151 mm x L118 mm x H38 mm; material should be aluminium alloy
•
Plastic pipe or conduit for protecting cords and cables
STEP 2 Organize the following (optional) components of the Cisco VC 031 Pendant
Mounting Adapter. The mounting adapter can be used alone or with one or more
pendant poles.
Included Parts
•
Mounting Adapter with Pendant Pole(s)
Camera Accessories Installation and Administration Guide
38
Accessory Installation Processes
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
2
Assembling the Enclosure
WARNING Equipment connected to outdoor cameras must be permanently grounded in
accordance with national and local codes. Statement 374
WARNING Hazardous voltages may be present in the outdoor camera cables under fault
conditions. Disconnect all cables from the outdoor cameras before servicing this
equipment. Statement 376
WARNING Do not use this product near water; for example, near a bath tub, wash bowl, kitchen
sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035
WARNING Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations. Statement 1036
WARNING Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface. Statement 1037
WARNING Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning. Statement 1038
Camera Accessories Installation and Administration Guide
39
Accessory Installation Processes
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
2
STEP 1 Feed the power cord and Ethernet cable through the enclosure cover, appropriate
bracket or adapter as needed for your situation.
STEP 2 Insert and connect the power cord and Ethernet cable to the appropriate sockets.
STEP 3 Using the two screws provided, secure the Cisco PVC300 network camera to the
cross iron plate.
Camera Accessories Installation and Administration Guide
40
Accessory Installation Processes
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
2
STEP 4 Connect the power cord and the Ethernet cable to the camera.
STEP 5 Secure the Cisco PVC300 network camera to the enclosure with the two provided
screws.
STEP 6 Attach the enclosure cover to the enclosure. You attach the two pieces by twisting
the cover into the groove found in the enclosure.
Camera Accessories Installation and Administration Guide
41
Accessory Installation Processes
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
2
!
CAUTION Repeated installations can make the cover difficult to attach to the enclosure.
However, do not add lubrication to the groove in the enclosure. Adding lubrication
could cause the seal to fail. Lubrication may allow water to enter the enclosure and
harm the camera, or the cover to loosen over time and fall.
STEP 7 Attach the enclosure to the appropriate bracket. The various brackets are shown
in the illustration.
STEP 8 Secure the enclosure to the selected bracket using the supplied L-type hex
wrench.
Camera Accessories Installation and Administration Guide
42
Accessory Installation Processes
Installing the Cisco PVC300 in a Cisco VC 030 Enclosure
2
Securing the Power Adaptor
A basic installation may leave the external power adaptor exposed to the
elements. It is recommended that you use either an extension cord so the power
adaptor can be placed indoors, or an electrical junction box.
DC Extension Cord
The specification of the extension cord, if needed, are as follows:
•
Custom length, 2-core copper conductor, type SPT-1 (UL/CSA style), 18
AWG, texture ≥ 2 x 0.824 mm², withstand 105° C, and 300V
Electrical Junction Box
The suggested requirements of the electrical junction box, if needed, are as
follows:
•
Protection level IP66 or above; inner size at least W151 mm x L118 mm x H38
mm; material should be aluminium alloy
NOTE Plastic pipe or conduit should be used to waterproof and protect the cables and
cords.
Where to Go Next
To mount your Cisco PVC300 camera to a corner or pole, use one of the following
procedures:
•
Installing the Cisco VC 032 Corner Mount Adapter
•
Installing the Cisco VC 033 Pole Mount Adapter
Camera Accessories Installation and Administration Guide
43
Accessory Installation Processes
Installing the Cisco VC 032 Corner Mount Adapter
2
Installing the Cisco VC 032 Corner Mount Adapter
Follow the instructions below to build the VC 032 adaptor that allows you to corner
mount the Cisco PVC300 camera.
STEP 1 Organize the following components of the Cisco VC 032 Corner Mount Adapter:
Included Parts
•
Two steel plates
•
Waterproof corrugated tubing fitting
•
Screw set for dome type housing
•
Screw set to lock steel plate
•
Silicone stoppers
Required Tools (Not Included)
•
Phillips-head screwdriver
Camera Accessories Installation and Administration Guide
44
Accessory Installation Processes
Installing the Cisco VC 032 Corner Mount Adapter
2
STEP 2 Integrate two pieces of steel plate together and securely lock using the provided
screws.
STEP 3 Attach the waterproof corrugated tubing fitting into the steel plate.
STEP 4 Securely lock the wall mount bracket with the corner mount adapter by using the
provided screws.
STEP 5 Feed the cables through the brackets and waterproof corrugated tubing fitting.
Camera Accessories Installation and Administration Guide
45
Accessory Installation Processes
Installing the Cisco VC 032 Corner Mount Adapter
2
STEP 6 Build the camera enclosure as described in Steps 3 - 8 in Installing the Cisco
PVC300 in a Cisco VC 030 Enclosure, page 37.
STEP 7 Use the silicone stoppers to plug the unused holes on the steel plate.
STEP 8 Screw the enclosure unit to the corner mount adapter.
STEP 9 Screw the enclosure unit and bracket to wall.
STEP 10 (Optional) Plastic pipe or conduit should be used to waterproof and protect the
cables and cords.
Camera Accessories Installation and Administration Guide
46
Accessory Installation Processes
Installing the Cisco VC 033 Pole Mount Adapter
2
Installing the Cisco VC 033 Pole Mount Adapter
Follow the instructions below to build the Cisco VC 033 adaptor that allows you to
pole mount the Cisco PVC300 camera.
STEP 1 Organize the following components of the Cisco VC 032 Pole Mount Adapter:
Included Parts
•
Steel plate
•
Three stainless steel belts
•
Waterproof corrugated tubing fitting
•
Screw set
•
Silicone stoppers
Required Tools (Not Included)
•
Phillips-head screwdriver
Camera Accessories Installation and Administration Guide
47
Accessory Installation Processes
Installing the Cisco VC 033 Pole Mount Adapter
2
STEP 2 Attach the waterproof corrugated tubing fitting into the steel plate.
STEP 3 Securely lock the wall mount bracket with the pole mount adapter by using the
provided screws.
STEP 4 Feed the stainless belt through the holes of the VC 033.
STEP 5 Feed the cables through the brackets and waterproof corrugated tubing fitting.
Camera Accessories Installation and Administration Guide
48
Accessory Installation Processes
Installing the Cisco VC 033 Pole Mount Adapter
2
STEP 6 Build the camera enclosure as described in Steps 3 - 8 in Installing the Cisco
PVC300 in a Cisco VC 030 Enclosure, page 37.
STEP 7 Fasten the enclosure unit to the pole mount adapter.
STEP 8 Attach the housing unit to the pole and securely lock the stainless belt to the pole.
STEP 9 (Optional) Plastic pipe or conduit should be used to waterproof and protect the
cables and cords.
Camera Accessories Installation and Administration Guide
49
Accessory Installation Processes
Installing the VC220 Cameras in a VC 025 Enclosure
2
Installing the VC220 Cameras in a VC 025 Enclosure
Follow the instructions below to install a Cisco VC220 network camera into a
Cisco VC 025 enclosure.
Before You Begin
Organize the components of the VC 025 enclosure unit.
Included Parts
•
Enclosure cover and base
•
TORX™ tamper-resistant screwdriver
•
Two screws to secure camera to base
•
Alignment Template
Required Tools and Parts (Not Included)
•
#2 Phillips screwdriver
•
Construction and electrical items needed for installation, as required
Preparing the Enclosure
WARNING Equipment connected to outdoor cameras must be permanently grounded in
accordance with national and local codes. Statement 374
WARNING Hazardous voltages may be present in the outdoor camera cables under fault
conditions. Disconnect all cables from the outdoor cameras before servicing this
equipment. Statement 376
Camera Accessories Installation and Administration Guide
50
Accessory Installation Processes
Installing the VC220 Cameras in a VC 025 Enclosure
2
WARNING Do not use this product near water; for example, near a bath tub, wash bowl, kitchen
sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035
WARNING Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations. Statement 1036
WARNING Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface. Statement 1037
WARNING Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning. Statement 1038
Camera Accessories Installation and Administration Guide
51
2
Accessory Installation Processes
Installing the VC220 Cameras in a VC 025 Enclosure
STEP 1 If a dome cover is attached to the camera, remove the two screws with the
provided TORX™ screwdriver, and then detach the dome cover.
STEP 2 Use the provided TORX™ screwdriver to loosen the four screws that attach the
195037
enclosure cover to the base and lift the enclosure cover off the base.
STEP 3 Place the camera into the base, aligning the bottom of the camera with the raised
base of the enclosure.
TIP
Temporarily place the enclosure cover back on to make sure the Status LED comes
through the opening in the enclosure.
Camera Accessories Installation and Administration Guide
52
2
Accessory Installation Processes
Installing the VC220 Cameras in a VC 025 Enclosure
STEP 4 Attach the camera to the base using the enclosed screws with a #2 Phillips
196038
screwdriver (not included) as you line up the LED with the LED cutout in the cover.
Installing the Enclosure
STEP 1 Place the provided template on the ceiling or wall where the camera and
enclosure are to be mounted.
196039
STEP 2 Complete any cutting and wiring as required.
Camera Accessories Installation and Administration Guide
53
2
Accessory Installation Processes
Installing the VC220 Cameras in a VC 025 Enclosure
STEP 3 Place camera and enclosure base into prepared opening and make all required
196040
connections.
Camera Accessories Installation and Administration Guide
54
2
Accessory Installation Processes
Installing the VC220 Cameras in a VC 025 Enclosure
STEP 4 Tighten the anchor screws found on the enclosure base with a Phillips screwdriver
until the anchors securely hold the unit into the wall or ceiling.
2
3
196041
1
Camera Accessories Installation and Administration Guide
55
2
Accessory Installation Processes
Installing the VC220 Cameras in a VC 025 Enclosure
STEP 5 Make any final focus or zoom adjustments to your camera. Refer to the VC220
196042
Administration Guide for setup instructions.
196043
STEP 6 Reattach the enclosure cover to the base using the TORX™ screwdriver.
Camera Accessories Installation and Administration Guide
56
A
Specifications
Cisco CAMLWA (Computar 1/3-inch 2.3 mm Wide Angle Lens)
Device Dimensions
1.259 inch x 1.622 inch (32 mm x 41.2 mm)
Power
n/a
Certification
RoHS
Operating Temp
-10ºC to 50ºC (º-4F to 140ºF)
Storage Temp
-20ºC to 60ºC (º-4F to 140ºF)
Operating Humidity
80% relative humidity, Non-Condensing
Storage Humidity
90% relative humidity, Non-Condensing
Camera Accessories Installation and Administration Guide
57
Specifications
Cisco CAMLMI (Tamron 1/3-inch 3-8 mm Varifocal 2.7X Zoom Lens)
A
Cisco CAMLMI (Tamron 1/3-inch 3-8 mm Varifocal 2.7X Zoom
Lens)
Device Dimensions
1.259 inch x 1.622 inch (32 mm x 41.2 mm)
Power
n/a
Certification
CE
Operating Temp
-20ºC to 60ºC (º-4F to 140ºF)
Storage Temp
-20ºC to 60ºC (º-4F to 140ºF)
Operating Humidity
80% relative humidity, Non-Condensing
Storage Humidity
80% relative humidity, Non-Condensing
Cisco VC 020 (Camera Exterior Enclosure with Heater and
Blower for the Cisco PVC2300/WVC2300)
Unit Weight
1.68 lb or 26.81 oz (.76 kg)
Power
N/A
Certification
CE, IP55, FCC, LVD, RoHS
Operating Temp
-20ºC to 50ºC (º-4F to 122ºF)
Storage Temp
-30ºC to 60ºC (º-22F to 140ºF)
Operating Humidity
0% to 90% relative humidity, Non-Condensing
Storage Humidity
0% to 95% relative humidity, Non-Condensing
Camera Accessories Installation and Administration Guide
58
Specifications
Cisco VC 020 (Camera Exterior Enclosure with Heater and Blower for the Cisco PVC2300/WVC2300)
Device Dimensions
A
5.31 inch x 5.51 inch x 17.2 inch (135 mm x 140 mm x 450 mm)
The inner dimensions of the camera mount:
415mm
62mm
275436
135mm
55mm
275437
450mm
1/4ʺ
Screw
The dimensions of the bracket base:
110.00mm
83.00mm
Camera Accessories Installation and Administration Guide
275435
95.00mm
8.00mm
59
Specifications
Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the Cisco PVC300)
A
Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the
Cisco PVC300)
Device Dimensions
Camera Accessories Installation and Administration Guide
60
Specifications
Cisco VC 030 (Camera Enclosure Exterior Pan Tilt for the Cisco PVC300)
Unit Weight plus
Bracket as shown in
picture
8.598 lb (3.9 kg)
Power Adapter
12VDC /3A
Certification
CE, FCC, C-Tick, ICES, LVD, RoHS, IP66
Operating Temp
-20ºC to 50ºC (º-4F to 122ºF)
Storage Temp
-20ºC to 50ºC (º-4F to 122ºF)
Operating Humidity
0% to 95% relative humidity, Non-Condensing
Storage Humidity
0% to 95% relative humidity, Non-Condensing
Camera Accessories Installation and Administration Guide
A
61
Specifications
Cisco VC 025 (Indoor Recessed Ceiling Mount Kit for the Cisco VC220)
A
Cisco VC 025 (Indoor Recessed Ceiling Mount Kit for the
Cisco VC220)
Device Description
A metal mount with plastic enclosure and clear dome cover.
Unit Weight
1.77 lb or 28.33 oz (.803 kg)
Camera Accessories Installation and Administration Guide
62
Specifications
Cisco VC 025 (Indoor Recessed Ceiling Mount Kit for the Cisco VC220)
Device Dimensions
7.09 inch x 4.72 inch (180mm x 120mm) D x H
Lens Color
Transparent lens for unaltered video images
Power
N/A
Camera Accessories Installation and Administration Guide
A
63
B
Where to Go From Here
Cisco provides a wide range of resources to help you and your customer.
Support
Cisco Small Business
Support Community
www.cisco.com/go/smallbizsupport
Cisco Small Business
Support and Resources
www.cisco.com/go/smallbizhelp
Phone Support Contacts
www.cisco.com/en/US/support/tsd_cisco_
small_business _support_center_contacts.html
Cisco Small Business
Firmware Downloads
www.cisco.com/go/smallbizfirmware
Select a link to download firmware for Cisco Small
Business Products. No login is required.
Downloads for all other Cisco Small Business
products, including Network Storage Systems, are
available in the Download area on Cisco.com at
www.cisco.com/go/software (registration/login
required).
Product Documentation
Cisco Small Business
Camera Documentation
www.cisco.com/go/smallbizcameras
Cisco Small Business
Cisco Partner Central for
Small Business (Partner
Login Required)
www.cisco.com/web/partners/sell/smb
Cisco Small Business
Home
www.cisco.com/smb
Camera Accessories Installation and Administration Guide
64