Installation Instructions
NeoSwitch Passive Infrared (PIR)
Dual Relay Occupancy Sensing Wall Switch
(Ground Required)
P/N 9850-000341-01
General Information
• Readallinstructionsonbothsidesofthis
sheetfirst
• InstallinaccordancewithALLlocalcodes
• Forindooruseonly
Specifications
Technology:PassiveInfrared(PIR)
Electrical Ratings:
120VAC:
• Incandescent/Tungsten–
Max.load:6.7amps,800W,50/60Hz
• Fuorescent/Ballast–
Max.load:10amps,1200W,50/60Hz
MotorLoad:¼HP@125VAC
277VAC:
• Fluorescent/Ballast–
Max.load:9.8amps,2700W,50/60Hz
Ballast Compatibility:Compatiblewithmagneticand
electronicballasts
No Minimum Load Requirement
Time Delays:Self-Adjusting,15seconds/test(10min
Auto),Selectable5,15,30minutes
Model
Model
Model
Model
Model
Coverage:Majormotion–1000sq.ft.
Minormotion–300sq.ft.
Light Level Sensing:0to200foot-candles
Operating Environment:
• Temperature:32°F–104°F(0°C–40°C)
• RelativeHumidity:20%to90%Non-condensing
Housing:Durable,injectionmoldedhousing.Polycarbonate
resincomplieswithUL94VO.
Size:
• MountingPlate/StrapDimensions:
4.195"Hx1.732"W(106.553mmx44mm)
• ProductHousingDimensions:
2.618"Hx1.752"Wx1.9"D
(66.5mmx44.5mmx48.26mm)
LED Indicators:RedLEDindicatesPIRdetection;Green
LEDactsasEcoMeterornightlightlocator.
Description
TheONW-P-1001-DMVOccupancySensingWallSwitchisaPassiveInfrared(PIR)motionsensinglightingcontroland
conventionalwallswitchall-in-one,usedforenergysavingsandconvenience.
PIR Technology
Thesensor’ssegmentedlensdividesthefieldofviewintosensorzones,anddetectsthechangesintemperaturethat
arecreatedwhenaperson,orpartofapersonassmallasahand,passesintooroutofasensorzone.
TheONW-P-1001-DMVallowsthecontroloftwoseparateloadswithoneoccupancysensorswitch.
EnergySaverMode–EitherorbothloadsmaybeconfiguredtoturnONmanually.Thedefaultsettingforthesecond
loadisManualON.Thisensuresthewallswitchonlyactivatesoneload.Ifbothloadsareonwhenthesensortimes-out,
onlytheprimaryloadwillbeactivated.IfthelightswereshutOFFmanually,theunitwillactivatetheprimaryloadonly.
InAutomaticONMode,thelightsturnONautomaticallywhenapersonenterstheroom.InManualONMode,thelights
areturnedONbypressingtheuniversallyrecognizedlighticonpushbutton.Ineithermode,thelightsstayONaslongas
thesensordetectsmotionintheroom.Whentheroomisvacated,thelightsturnOFFautomaticallyafterapresettime
delayinterval.
Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditionsbyadjustingsensitivityandtime
delayinreal-time.Byadjustingsensitivityandtimedelayautomatically,thesensorismaximizingthepotentialenergy
savingsthatareavailableintheparticularapplication.
TheEcoMeterprovidesavisualindicatorofenergyusage,increasingenduserawarenessandremindingindividualsto
takecontroloftheirlightingtomaximizeenergysavings.
TheDaylightingfeaturepreventslightsfromturningON,whentheroomisadequatelyilluminatedbynaturallight.
Walk-ThroughfeaturemaximizesenergysavingsbynotleavingthelightsONafteramomentaryoccupancy.Thesensor
willswitchthelightsONwhenitdetectsapersonenteringthearea.Ifthesensordoesnotcontinuetodetectmotion20
secondsfollowingtheinitialactivation,itwillautomaticallygotoashorter2minutetimedelay.
BathroomMode–Whenselected,bathroommodekeepsthesecondrelayONforanadditional8minutes,afterthe
firstrelayhasbeenturnedOFF.Combinethiswithchangingthepushbuttontothelight/fangraphicandyounowhavethe
universallyrecognizedandeasytousebathroomsolution.
RelaySwapOption–Acommonprobleminelectricwiringiswiringthewrongswitchtothewrongload.Thiscanmake
controlofloadsconfusingtoanenduser.TheRelaySwapoptionsolvestheproblembyallowingtheswitchbuttonsonthe
faceoftheunittobeswapped,aftertheunitiswiredandinstalled.
Action
EcoMeter
Benefit
Apersonentersthespaceand
oneoftheloadsisactivated
50%
Increasedawarenessofenergysavings
BothloadsareON
OFF
Theareaisvacatedandthe
lightsturnOFFautomatically
100%
Increasedawarenessofenergysavings;
Actsasanightlightlocator
ApersonturnsthelightsOFF
manuallyuponexitinganarea
100%
Increasedawarenessofenergy
savingsandremindsindividualstotake
controloftheirlightingforadditional
savings;Actsasanightlightlocator
IftheDaylightingfunctionis
activatedforoneofthetwoloads
andthereissufficientdaylightinthe
space,theunitwillholdthatloadOFF
50%
Increasedawarenessofenergy
savings;Letspersonsknowthatthe
daylightsensorisholdingthelightsOFF;
Actsasanightlightlocator
100%
Increasedawarenessofenergy
savings;Letspersonsknowthatthe
daylightsensorisholdingthelightsOFF;
Actsasanightlightlocator
EcoMeter Operation
Load 1
Load 2
EcoMeter LED
OFF
OFF
100%
ON
OFF
50%
OFF
ON
50%
ON
ON
OFF
IftheDaylightingfunctionis
activatedforbothloadsandthereis
sufficientdaylightinthespace,the
unitwillholdthatloadsOFF
Coverage
TheONW-P-1001-DMVisdesignedforofficesupto300squarefeet.
36
#
#
#
#
#
ONW-P-1001-DMV-W
ONW-P-1001-DMV-V
ONW-P-1001-DMV-LA
ONW-P-1001-DMV-G
ONW-P-1001-DMV-B
Installation
TheONW-P-1001-DMVcanbeinstalledinanystandardsinglegangbox.Itmaybe
installedinthesamemannerasanordinarywallswitch.
• WiretheONW-P-1001-DMVasdescribedinthewiringsection
• MounttheONW-P-1001-DMVinthejunctionbox
Wiring
CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned OFF at
the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main switch
for a fluorescent lighting circuit, the circuit breaker should be marked “SWD.” All installations should be in
compliance with the National Electric Code and all state and local codes.
NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is shortened
by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the effects of cycling.
1. MakesurepoweristurnedOFFatthebranchcircuitbreaker.
2.Wireunitsasshowninwiringdiagramsperapplicablevoltagerequirements.
3.Mountunittowallbox.
4. TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.
5.Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)
6.Installwallswitchplate.
,
,
20
Minor Motion, IR
Major Motion, IR
Wiring Diagram 1: 120/277 VAC dual level single circuit wiring diagram
,
8
120/277 VAC
Maximum coverage area may
vary somewhat according to room
shape and the presence of obstacles.
Location
BLACK
BLUE
RED
RED
GREEN
LOAD 2
LOAD 1
GROUND
NEUTRAL
WheninstallingtheONW-P-1001-DMVinanewjunctionbox,choosetheswitchlocationcarefullytoprovideoptimum
coverageoftheoccupiedarea.Whenreplacinganexistingwallswitch,bearinmindthattheremustbeaclearline-of-sight
betweenthesensorandtheareatobecovered.AvoidpointingtheONW-P-1001-DMVdirectlyintothehallwaywhereitmay
detectpassers-by.
Eaton’s Cooper Controls Business
203 Cooper Circle
Peachtree City, Georgia 30269
www.coopercontrol.com
Wiring Diagram 2: 120/277 VAC dual level dual circuit wiring diagram
CIRCUIT 1
120/277 VAC
BLACK
BLUE
CIRCUIT 2
120/277 VAC
RED
RED
GREEN
1. WalkaroundtheroomandmonitorLEDs.
2. Standindifferentpartsoftheroomandwaveyourhands.
LEDshouldonlyturnONforonesecondwitheachmotion.
(IfLEDdoesnotturnON,gotoInstallerAdjustments–
SensitivityAdjustmentSection)
3. Standstillthreetofourfeetawayfromsensorforfive
seconds.LEDshouldnotturnON.(IfLEDturnsON,goto
InstallerAdjustments–SensitivityAdjustmentssection)
4. Walkoutsidetheroomandwait15secondsforthe
lightstoturnOFF.(IflightsdonotturnOFFgotoInstaller
AdjustmentsSection)
5. Re-entertheroomtoactivatesensor.(Iflightsdonotturn
ONgotoTroubleshootingSection)
6. Atthispointyoucanexittheroomandletthesensortimeout.Whenthesensortimes-outandisinactiveforfive
minutes,theunitwillgotoa10minutetimedelayuser
modesetting.
LOAD 1
LOAD 2
CIRCUIT 1
GROUND
NEUTRAL (CIRCUIT 2)
NEUTRAL (CIRCUIT 1)
Note:ToplaceintoTestMode,toggleDIPSwitch12outofitscurrent
Wiring Diagram 3: 120/277 VAC dual level single circuit three-way wiring diagram
position,wait3seconds,andthenbackintoitsoriginalposition.
TRAVELER
WIRES
Override
TheOverridesettingallowsthesensortooperateasaserviceswitchintheunlikelyeventoffailure.
1. MoveDIPSwitch8up.
2.ThepushbuttoncanbeusedtomanuallyturnlightsONorOFF.
Red (PIR)
Detection LED
PIR Lens
Daylight
Sensor Level
Adjustment
Troubleshooting
Issue
Possible Causes
Suggestions
SensorisinManualONmode
Presspushbutton.IfAutoMode
isdesiredchangeActivationModetoAuto.
SensorwasturnedOFFmanually.Ifthe
SensorwasturnedOFFmanuallybefore
thetimedelayexpired,lightswillremain
OFFfortheremainderofthetimedelay.
CheckEcoMeterLED.IfLEDisONthisisan
indicationthatthelightswereturnedOFFmanually.
PressthepushbuttontoturnthelightsbackON.
DaylightingFeatureEnabled
IfalllightsarerequiredtoturnONadjust
DIPSwitches11and12and/ordaylightpotentiometer.
Powerinterruption
Checkincomingvoltageand/orwiring.
DaylightingFeatureEnabled
IfalllightsarerequiredadjustDIPSwitches
11and12and/ordaylightpotentiometer.
Powerinterruption
Checkincomingvoltageand/orwiring.
EcoMeter
DIP Switches
Lights
Will Not
Turn ON
automatically
ON/OFF Buttons
1&2
120/277 VAC
Installer Adjustments
BLACK
BLUE
RED
RED
BLUE
GREEN
RED
GREEN
LOAD 1
LOAD 2
PIR Sensitivity
1. Standindifferentareasoftheroomandwaveyourhands.
2.IftheRedLEDdoesnotturnON,checkforanyobstructions.
3.Standstillthreetofourfeetawayfromsensorforfiveseconds.LEDshouldnotturnON.
4. IfRedLEDturnsONwithoutmotionorisconstantlyonadjustPIRsensitivityto50%bymovingDIPSwitch5up.
BLACK
RED
GROUND
GROUND
Field-of-view outside the space
1. AdjustPIRsensitivityto50%bymovingDIPSwitch5up.
2.Usenon-reflectivetapestripstocovertheportionsofthesensorlensthatviewoutsidethespace.
NEUTRAL
THREE-WAY WIRING DIAGRAM:
LIGHTS WILL TURN OFF, WHEN UNIT THAT WAS TURNED ON LAST AND/OR DETECTED MOTION LAST TIMES-OUT
CAUTION: If a room is wired for two circuits using two separate hot leads, it is very important to connect only one circuit
per relay. Both circuits must be fed from the same phase.
DIP Switch Settings
DIP Switch Legend
Time Delay
Activation
Relay 1
DIP Switch
1
2
PIR Sensitivity Walk-Through Mode
EcoMeter
Override
Bathroom
Relay Swap
Relay 2
3
Daylighting
Relay 1
4
6
5
7
9
8
Relay 2
11
10
12
Auto*
Auto
Auto
Full
Disable
Enable
Disable
Disable
Normal
Disable
Disable
5 Minutes
Manual
Manual
50%
Enable
Disable
Enable
Enable
Swap
Enable
Enable
15 Minutes
30 Minutes
*Self-Adjusts to
10 min. user
mode
Default =
1
2
3
4
5
6
7
8
9
10 11 12
Checkout and Adjustment
AdjustmentsshouldbemadewiththeHVACsystemONsothattheinstallerwillbeabletodetecttheeffectofairflowon
theoperationoftheONW-P-1001-DMV.Useonlyinsulatedtoolstomakeadjustments.
Immediatelyafterapplyingpowertothelightingcircuit,waitapproximatelytwominutesfortheswitchtopower-up
andstabilize.
Self-Adjust
Sensorisshippedinself-adjustmode.ThisappliestotimedelayandPIRsensitivity.InpreparationfortheInstallerTest,
thetimedelayissetto15seconds,afterthesensorisinstalled,poweredONandhasstabilized,theunitwilltime-out15
secondsafterthelastmotiondetected.CoverageandsensitivitycanbeconfirmedbywatchingtheRed(PIR)indicatorLED
onthefrontofthesensor,whilemovingaroundtheroom.
Daylight Adjustments
TheDaylightingfeaturepreventsthelightsfromturningONwhen
theroomisadequatelyilluminatedbynaturallight.Ifthereisenough
lightintheroomregardlessofoccupancy,thesensorwillholdthe
lightsOFF.Ifthereisnotenoughlightintheroom,thesensorwill
allowthelightstoturnONwhenoccupied.TheDaylightingfeature
1 2 3 4 5 6 7 8 9 10 11 12
11 and 12
allowstheselectionofwhichrelaytocontrolviadaylighting(dualload
modelsonly).ThesensorwillnotallowtheDaylightingfeaturetoturn
theloadOFFuntilthespaceisvacantifthelightlevelrisesabovethe
setpointandthetimedelayexpires.WhileinManualActivationMode,
ifsomeoneattemptstoturntheloadONandthereissufficientdaylightavailabletheDaylightingfeaturewillholdthelightsOFF.
1. Setthelightlevelwhentheambientlightisatthelevelwherenoartificiallightisneeded.Ifthisfeatureisnotneeded,
leavethelightlevelatmaximum(fullyCW).
2.SetDIPSwitches11(Relay1)and/or12(Relay2)fordaylightcontrol.
3.Withtheload(s)ON,putthesensorintoTestMode.ToplaceintoTestMode,toggleDIPSwitch12outofitscurrent
position,wait3secondsandthenbackintoitsoriginalposition.
4. Setthelightleveltominimum(fullyCCW).
5.Letthesensortime-outsolightsareOFF.EnterthespaceandlightsshouldremainOFF.
6.MakesurenottoblockthesensorfromthedaylightsourceandadjustthelightlevelpotentiometerCWinsmall
increments.(Pause5secondsbetweeneachadjustment)
7. LightswillnotturnONuponoccupancyactivation,whentheambientlightlevelexceedsthedaylightthresholdsetting.
Time Delay Adjustments
Peoplewhoremainverystillforlongperiodsoftimemayneed
alongertimedelaythanthedefaultsettingof10minutes.Aslong
astheself-adjustingfeatureisenabled,theswitchwillrespond
toeachpairoffalse-OFFswithnonormalOFFinbetween,by
alternatelymakingslightadjustmentstoeithertimedelay(by2minute
increments)orsensitivity,sothereshouldbenoneedformanual
adjustment.Ifmanualadjustmentisdesired,refertoTimeDelay
1 and 2
settingsinDIPSwitchlegend.
ResetsensortimedelaytofactorysettingsbymovingDIPSwitches
1and2down.(IfDIPSwitches1and2arealreadydown,toggleDIP
Switch1outofitscurrentposition,wait3seconds,andthenbackto
itsoriginalposition)
Printed in Malaysia
1
2
3
4
5
6
7
8
9
Lights
Will Not
Turn ON
manually
If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879
Lights
Will Not
Turn OFF
automatically
Override
MakesuresensorisnotinOverrideMode(DIPSwitch8up).
Self-Adjust
IfsensorisinSelf-AdjustMode,itmaybepossibleforthe
unittohaveincreasedthetimedelaytoa30minutedelay.
IfthelightsdonotturnOFFafter30minutesfollownextstep.
30MinuteDelay
Maximumtimedelayis30Minutes.CheckDIP
SwitchestoverifyDIPSwitchsettings.Iflightsdo
notturnOFFatthesettimedelay,checknextstep.
PIRactivatedbyheatsourceotherthanoccupant
MoveDIPSwitch5up.
Lights
Will Not
Turn OFF
manually
CallTechnicalServices
If lights will still not turn OFF, call Technical Services at 1-800-553-3879
Warranties and Limitation of Liability
Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.
10 11 12
Eaton’s Cooper Controls Business
203 Cooper Circle
Peachtree City, Georgia 30269
www.coopercontrol.com