INSTALLATION INSTRUCTIONS
V90087 REV D
Avoid Fire or Electric Shock
QUIET CEILING SQUARE REMODEL
QCT905 AND QCM514 BASED SERIES
Page 1 of 2
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
Above Ceiling Clearance
Fixture Housing Cover
J-Box
J-Box Door
Fixture
Knockouts
Insulation
Detector
Ceiling Cutout
14.29" x 7.38"
5.39
Dimension measure from
below ceiling to top of fixture
Ceiling
Wing nut
Rotational Clamp
Bracket(Folded)
Figure 1
Pre-Installation Preparation:
1.
2.
Perforated Mudding Frame
Check for Above Ceiling Clearance of 5.39. See Fig.1.
Make 14.29" x 7.38" Cutout in Ceiling.See Fig.1.
9.
Electrical Connection:
3.
Turn OFF Electrical service.
4.
All appropriate electrical "rough" wiring should be completed.
5.
Remove J-Box door with provided wing nut.See Fig.2.Connect
wiring inside J-Box to Existing Service through knockouts
provided.Open Fixture Housing Cover while wiring for ease of
connection.See Fig.2.
6.
Figure 2
Holding Fixture firm to ceiling surface,drive the four
(4) #8 X 3" Set Screws (See Fig.5.) located on the underside
of Perforated Mudding Frame(See Fig 5) clockwide to rotate
and lock the Rotational Clamps Brackets to ceiling.DO NOT
over tighten the screws or rotational clamp Brackets.Over
tightening may crack ceiling material.
Optional: Install additional drywall/zip screws into perforated
Mudding Frame to guarantee flatness Mudd-In.
10.
Tape and Mudd Perforated Mudding Frame until sufficiently
smooth.
Folded Rotational
Clamp Bracket
Reattach J-Box door to Housing with wing nut and close the
fixture housing cover.
Unfolded Rotational
clamp Bracket
Note: Single circuit cable only and/or single fixture with next
jumper.Wire Single fixture or wire through with second cable(to
next fixture) in J-Box.
Installation of Housing:
7.
Fold four(4) rotational Clamp brackets tight against Fixture (See
Fig.3.) making sure Brackets are in upper most(highest)
threaded position(see fig.4) to accommodate largest ceiling
thickness.
8.
Carefully insert wired fixture through ceiling cutout into available
ceiling area avoiding all insulation and combustible surface by 3"
all around.See Fig.1.
Perforated Mudding
Frame
# 8 Set Screw
Figure 3
(View From Below Ceiling, Hidden Lines shown)
INSTALLATION INSTRUCTIONS
V90087 REV D
Avoid Fire or Electric Shock
QUIET CEILING SQUARE REMODEL
QCT905 AND QCM514 BASED SERIES
Page 2 of 2
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
J-Box Door
Trim Installation:
Fixture
Rotational Bracket
Clamp
# 8 Set Screw
Ceiling
Figure 4
Rotational Clamp Bracket
Bracket
Fixture
Safety Cable
Ceiling
# 8 Set Screw
Trim Mechanism
Ball Detent Catch
Figure 5
11.
Connect Safety Cable attached to Trim to Fixture by inserting Safety
Cable through opening in Fixture and inserting Snap Hook
(See Fig. 5) on end of Safety Cable into hole in Bracket attached to
inside of fixture.
12.
Install Trim Mechanism into fixrue by pressing firmly to seat ball
detent catches. See Fig.5.