VERSYS CONTINUOUS - ETG-STG Installation Manual
STEP 1 - CEILING PREPARATION
Figure 1
FIXTURE SLOT/OPENING
IN GRID CEILING SYSTEM
30
", 3
6
", 4
8
"O
R6
0"
RU
NL
EN
GT
H
CEILING TILES
6"
REMOVED CEILING TILES
A) GRID CENTERS TO BE 6"
(AS SHOWN IN FIGURE 2 AND FIGURE 3).
LENGTH OF GRID OPENING HAS TO BE ACCORDING
TO THE ORDERED FIXTURE OR FIXTURES RUNS.
B) BEFORE INSTALLING FIXTURES IN GRID CEILING
PLEASE REMOVE CEILING TILES NEXT TO FIXTURE
SLOT AS SHOWN IN FIGURE 1
Figure 2
Figure 3
6" OC
9/16” SLOT TEE GRID CEILING SYSTEM (STG)
VERSYS CONTINUOUS ETG-STG Installation Manual, Page 1
6" OC
15/16” EXPOSED TEE GRID CEILING SYSTEM (ETG)
VERSYS CONTINUOUS - ETG-STG Installation Manual
STEP 2 - FIXTURE PREPARATION
Figure 1
1) REMOVE FIXTURE FROM PACKAGING BOX.
2) FROM "BOR" AND "INT" MARKED FIXTURES REMOVE WIREWAY SIDE COVERS
AND JOINING BOLTS AND NUTS AS SHOWN IN FIGURE 1.
MOUNTING
BRACKET
THROUGH
WIRE
JOINER
BRACKET
ALIGNER
BRACKET
WIREWAY
SIDE COVERS
JOINING BOLTS
(1/4-20 3/4"LONG)
DETAIL "A"
1/4-20 HEX NUTS
#8-3/8" LONG
PAN HEAD SCREW
DETAIL "A"
Figure 2
Figure 3
IF USING "ETG"*
GRID CEILING SYSTEM
THIS TAB IS AS SHOWN
IN FIGURE 2.
IF USING FIXTURE
IN "STG"** GRID
CEILING SYSTEM
THIS TAB MUST BE
FOLDED OUT AS SHOWN
IN FIGURE 3.
* - "ETG" - 15/16" X 1 1/2" HIGH FLAT "T" GRID CEILING.
** - "STG" - 9/16" BOLT "T" X 1 11/16" HIGH SCREW SLOT GRID CEILING.
VERSYS CONTINUOUS ETG-STG Installation Manual, Page 2
VERSYS CONTINUOUS - ETG-STG Installation Manual
STEP 3 - FIXTURE INSTALLATION
Figure 1
Figure 2
CEILING
TILE
CEILING
TILE
"BOR"
FIXTURE
"BOR"
FIXTURE
TIRE WIRE
(BY OTHERS)
FIXTURE SLOT/OPENING
IN GRID CEILING SYSTEM
FIXTURE SLOT/OPENING
IN GRID CEILING SYSTEM
A) START INSTALLING FIXTURE FROM LEFT TO RIGHT (CLOCKWISE)
STARTING WITH "BOR"** MARKED FIXTURE AS SHOWN IN FIGURE 1.
B) ONCE FIXTURE IS INSTALLED IN FIXTURE SLOT/OPENING, PLEASE
USE TIE WIRE (AS SHOWN IN FIGURE 2) TO SECURE FIXTURE TO
PLENUM ACCORDING TO NEC, UL AND CITY CODES.
Figure 3
* - "IND" - INDIVIDUAL FIXTURE;
** - "BOR" - BEGINNING OF RUN FIXTURE;
*** - "INT" - INTERMEDIATE IN RUN FIXTURE;
**** - "EOR - END OF RUN FIXTURE.
Figure 4
TIE WIRE
(BY OTHERS)
TIE WIRE
(BY OTHERS)
"EOR" FIXTURE
"EOR" FIXTURE
"BOR" ("INT")
FIXTURE
"BOR" ("INT")
FIXTURE
FIXTURE SLOT/OPENING
C) BRING NEXT FIXTURE ("INT" OR "EOR" AS SHOWN IN FIGURE 3;
SECURE FIXTURE TO PLENUM AS DESCRIBED
IN PARAGRAPH "B” AND SHOWN IN FIGURE 4.
VERSYS CONTINUOUS ETG-STG Installation Manual, Page 3
* - "IND" - INDIVIDUAL FIXTURE;
** - "BOR" - BEGINNING OF RUN FIXTURE;
*** - "INT" - INTERMEDIATE IN RUN FIXTURE;
**** - "EOR - END OF RUN FIXTURE.
VERSYS CONTINUOUS - ETG-STG Installation Manual
STEP 4 - CONNECTING THROUGH WIRING AND POWERING INSTALLED FIXTURES
WORK FROM BELOW UTILITY COMPARTMENT TO JOIN FIXTURES IN RUN.
BEFORE DOING STEP # 4 AND STEP # 5 WHIP MUST BE WITHOUT POWER!
Figure 1
A) FIXTURES INSTALLED IN A SLOT/OPENING WILL LOOK AS SHOWNIN FIGURE 1;
B) USE JOINING BOLTS AND HEX NUTS (FROM STEP 2) TO JOIN AND ALIGN
FIXTURES AS SHOWN ON FIGURE 2;
C) USING PROVIDED (BY NEO-RAY) QUICK CONNECTOR OR WIRE NUTS
THROUGH WIRE FIXTURES AS SHOWN IN FIGURE 2.
ALIGNER BRACKET
WITH SET SCREW
THROUGH WIRES
JOINER BRACKET
Figure 2
WIRE NUTS
SLIDE ALIGN BRACKET
TO INTERMEDIATE POSITION
AND USING SET SCREWS
ALIGN FIXTURE HOUSINGS
VERSYS CONTINUOUS ETG-STG Installation Manual, Page 5
JOIN FIXTURES
BY 1/4-20 BOLTS
AND NUTS
VERSYS CONTINUOUS - ETG-STG Installation Manual
STEP 5 - POWERING INSTALLED FIXTURES
REMOVE ACCESS PLATE, ATTACH FEED WHIP
TO ACCESS PLATE AND CONNECT FIXTURE FEED
WIRES TO WHIP.
PUT BACK ACCESS PLATE ONTO FIXTURE.
FEED WHIP
(BY OTHERS)
ACCESS
PLATE
FEED WIRES
NOTE:
FOR DIMMING BALLAST FULL FUNCTIONALITY
CUSTOMER HAS TO HAS KEEP LAMPS "ON" MINIMUM 100 HOURS
FOR PROPER FULL RANGE DIMMING AND LAMP STABILITY
STEP 6
A) INSTALL WIREWAY COVER IN UTILITY COMPARTMENT
AND CLOSE COMPARTMENT BY COVER;
B) CLOSE CEILING BY TILES
AS SHOWN BELOW.
WIREWAY
COVER.
CEILING TILES
UTILITY
COMPARTMENT
UTILITY
COMPARTMENT
COVER
C) INSTALL LAMPS (NOT BY NEO-RAY).
VERSYS CONTINUOUS ETG-STG Installation Manual, Page 6