D E S C R I P T I O N
The real workhorse in emergency lighting systems...these durable, reliable units are unparalleled in performance and provide freedom from maintenance. The HR Series units provide a low-cost, solid-state lighting system for applications in industrial, commercial or multi-housing environments. High and ultra-high capacity makes them ideal for installations where a large number of heads/exits will be remotely operated.
Type
Date
S P E C I F I C AT I O N F E AT U R E S
E l e c t ro n i c
- Dual Voltage Input
120/277 VAC, 60 Hz
- Line-latching
- Solid-state Voltage
Limited Charger
- Solid-state Switching
- Low-Voltage Disconnect
- Brownout Circuit
- Overload/Short Circuit Protection
- Test Switch/Power
Indicator Light
- Isolation Transformer
B a tte r y
- Sealed Lead Calcium,
Recombination
- Maintenance-Free, Long-Life
- Full Recharge Time,
24 hrs. (max.)
- Polarized Battery Terminals
H o u s i n g C o n s t ru c t i o n
- 18-Gauge Die-Formed
Steel Housing
- 18-Gauge Die-Formed
Steel Cover
- Knockout, Conduit or Cord Set
- Universal J-Box Mounting
Pattern (High Capacity
Series Only)
- Keyhole Mounting Slots
- White Finish
C o d e C o m p l i a n c e
- UL 924 Listed
- City of Chicago Approval
No. 3238
- Life Safety NFPA 101
- NEC/OSHA
- Most State and Local Codes
Wa rra n t y
- Unit: 1-year
- Battery: 5-year pro-rata
H e a d / L a m p Da t a
- Two Heads Standard
- Top Mounted
- Glare-Free Lens
- Fully Adjustable
- Remote Capability
- Metal Heads with Die Cast
Metal Swivel
- Halogen Lamp Standard
- Matches Housing Finish
M o u n t i n g R e q u i re m e n t
- Mount only on a vertical plane
(i.e. wall mount, etc.)
18"
[457mm]
11 3/4"
[299mm]
4 1/4"
[108mm]
5 3/4"
[146mm]
12 1/2"
[318mm]
14 1/2"
[368mm]
8 1/4"
[210mm]
9"
[229mm]
17 1/4"
[438mm]
19 1/4"
[489mm]
Figure 1 High Capacity Figure 2 Ultra High Capacity
ORDERING INFORMATION
HR87C
HR117C
HR180C
6 VO LT
H I G H C A PAC I T Y
U LT R A H I G H C A PAC I T Y
S E A L E D L E A D
C A L C I U M B AT T E RY
C H I C AG O C O D E
E M E R G E N CY L I G H T I N G
Series
HR87C
HR117C
HR180C
Options 1, 2
V = Voltmeter
TDM
= Time Delay Monitor
Accessories
Mounting Kit
3
2MSWH
= Mounting Shelf (High Capacity) 4
3MSWH = Mounting Shelf (Ultra-High Capacity) 5
3BRWH = Mounting Brackets
Protective Housing
WG3
= Wire Guard (Ultra High Capacity) 5
WG7 = Wire Guard (High Capacity) 4
VS2 = Polycarbonate Vandal Shield
VK1 = Voltmeter
Notes: 1 Consult your Cooper Lighting Representative for alternate lamps and additional options. 2 Add as a suffix. 3 Order separately. 4 High Capacity Units. 5 Ultra
High Capacity Units.
Specifications and dimensions subject to change without notice.
Consult your representative for additional options and finishes.
E N E R G Y D ATA
HR87C
Input Current (Max.):
120V= .50A
277V= .21A
HR117C
Input Current (Max.):
120V= .53A
277V= .22A
HR180C
Input Current (Max.):
120V= .98A
277V= .43A
ADX041293 pc
2011-07-11 12:56:07
2011-07-11 13:07:12

HR87C
HR117C
HR180C
6 - VO LT E L E C T R I C A L R AT I N G S
Model
HR87C
HR117C
HR180C
R a t e d W a t t a g e to 87 1/2% of Rated D.C. Voltage
Type
SLC
SLC
SLC
DC Voltage 1 1/2 Hours Lamp Watts Remote Watts
6
6
6
87
117
180
24
24
24
*Batteries may be shipped separately.
SLC =Sealed Lead Calcium
63
93
156
L a m p I n f o r m a t i o n
Type Wattage Number Figure
Halogen
Halogen
Halogen
12
12
12
29-66
29-66
29-66
1
1
2
P H OTO M E T R I C S
H o r i z o n t a l D i s t r i b u t i o n
15
FEET
LEFT
0
FEET
1FC 0.5 0.3 0.2 0.1
RIGHT
15
0 20 30 40 50 60
LAMP
AXIS
FEET FROM LAMP (Measured on axis)
Ve r t i c a l D i s t r i b u t i o n
15
FEET
LEFT
0
1FC 0.5
0.3
0.2
FEET
RIGHT
15
0 20 30 40 50 60
FEET FROM LAMP (Measured on axis)
0.1
LAMP
AXIS
Lamp No. 29-45 and 29-66
Initial Lumens – 302
Lamp No. 29-45 and 29-66
T E C H N I C A L DATA
H e a d s
All metal formed aluminum lampheads. The die cast metal three dimensional swivel assembly permits approximate aiming adjustment from
80° vertical and 358° rotation. The placement is secured with a lockable pivot mounted on a rotating base ring.
L a m p s
Designed specifically for emergency lighting applications, the PAR 36 sealed beam type design insures optimum glarefree light distribution along with horizontal and vertical adjustment by rotating the lens within the housing. Tungsten halogen lamps maximize light output with lower wattage.
H o u s i n g
The rugged 18-gauge dieformed steel housing is finished with an attractive white corrosionresistant polyester powder coat paint. Cabinet has keyhole mounting slots, universal mounting pattern, and knockouts in rear and side for
AC/DC wiring connections and accessory cord set. Up to three lighting heads can be mounted on the cabinet.
L i n e - L a t ch e d
Sure-Lites’ line-latched electronic circuitry makes installation easy and economical. A labor efficient AC-activated load switch prevents the lamps from turning on during installation to a non-energized AC circuit. Line-latching eliminates the need for a contractor’s return to a job site to connect the batteries when the building’s main power is permanently turned on.
S o l i d - S t a te C h a rge r
Supplied with a 120/277 VAC, voltage regulated solid-state charger. Immediately upon restoration of AC current after a power failure, the charger provides a high charge rate. The charge circuit reacts to the condition of the battery and alters the rate of charge in order to maintain peak battery capacity and maximize battery life. Solid-state construction recharges the battery following a power failure in accordance with UL 924.
O ve rl o a d a n d S h o rt C i rc u i t P ro te c t i o n
The solid-state overload monitoring device in the DC circuit disconnects the lamp load from the battery should excessive wattage demands be made and automatically resets when the overload or short circuit is removed. This overload current protective feature eliminates the need for fuses or circuit breakers for the DC load. Brownout Circuit The brownout circuit in
Sure-Lites’ units monitors the flow of AC current to the unit and activates the emergency lighting system when a predetermined reduction of AC power occurs. This dip in voltage will cause most ballasted fixtures to extinguish causing loss of normal lighting even though a total power failure has not occurred.
S o l i d - S t a te Tra n s fe r
The unit incorporates a solidstate switching transistor which eliminates corroded and pitted contacts or mechanical failures associated with relays. The switching circuit is designed to detect a loss of AC voltage and automatically energizes the lamps. Upon restoration of the AC power, the emergency lamps will switch off and the charger will automatically recharge the battery.
L ow - Vo l t a ge D i s c o n n e c t
When the battery’s terminal voltage falls below
80% of the rated voltage, the low-voltage circuitry disconnects the lighting load. The disconnect remains in effect until normal utility power is restored, preventing deep battery discharge.
Te s t Sw i t ch / Powe r I n d i c a to r L i g h t
Conveniently located Test Switch allows for manual verification of proper operation of the transfer circuit and emergency lamps. The
Power Indicator Light provides visual assurance that the AC power is on.
S e a l e d L e a d C a l c i u m B a tte r y
The fully sealed, long-life, maintenance-free lead calcium battery is ideal for emergency lighting applications. These recombinant cycle batteries typically provide eight to ten years of life and may be operated in any position.
Wa rra n t y
All Sure-Lites’ units are backed by a firm oneyear warranty against defect in material and workmanship (excluding lamps). Maintenance free, long-life, sealed lead calcium batteries carry a five-year pro-rata warranty.
Specifications and dimensions subject to change without notice.
Sure-Lites • Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • TEL 770.486.4800 • FAX 770.486.4801
ADX041293 pc
2011-07-11 12:56:07
2011-07-11 13:07:12