Accessories
PERF-O GRIP™ Bolt Washer Seat
Carriage
Bolt **
Part Number Includes
(1) Bolt Washer Seat (PBOLTSEAT)
P Bolt
Seat
Flat
Washer
Order Separately
(1) 3/8”-16 Carriage Bolt **
(1) 3/8” Flat Washer
(1) 3/8”-16 Hex Nut
Hex Nut
Field drilling is required.
** Plank carriage bolt lengths = Side Channel Height + 1”
Walkway carriage bolt = 5/16”-18 x 2”
PERF-O GRIP Bolt Seats help provide a secure anchor
of the grating to structural supports. The standard bolt
seat features oblong holes specifically designed to help
ensure a vertical anchor (with a 3/8” bolt) even if the
hole is off concentrically by as much as 1/4”.
Hardware is not provided.
Bolt Washer Seat (P Bolt Seat)
UPC Number
Catalog Number
Wt./Ea.
66251626616
PBOLTSEAT
0.10
Assembly
1. Align PERF-O GRIP planks on I-Beam or other
anchoring cross-member.
2. Mark the I-Beam for drilling purposes under the
PERF-O GRIP hole nearest the end. Drill a pilot hole.
3. Remove PERF-O GRIP plank and drill a finish hole.
4. Replace PERF-O GRIP plank to its original position.
Place bolt seat in the PERF-O-GRIP hole which is
now lined up with the drilled hole.
5. Run the carriage bolt through the bolt seat,
PERF-O GRIP and I-Beam, and tighten with washer
and nut until secure.
6. Test for movement or slippage. If PERF-O GRIP
planks are not secure, check fastening system for
loose or missing parts. Repeat steps 1 thru 5.
Note: Do not walk on PERF-O GRIP planks if
they are not secure. Serious injury could result.
Welding
A common method of fastening safety grating is
welding. It is recommended that all B-Line Safety
Grating products be fillet welded per AWS D1.3.
For more information, consult Technical Services.
PERF-O GRIP Grating
13
Accessories
PERF-O GRIP™ J-Clip
Carriage
Bolt **
Part Number Includes
P Bolt
Seat
(1) J-Clip & (1) P Bolt Seat
Order Separately
(1) 3/8”-16 Carriage Bolt **
(1) 3/8” Flat Washer
(1) 3/8”-16 Hex Nut
J Clip
Flat
Washer
Hex Nut
** Plank carriage bolt lengths = Side Channel Height + 1”
Walkway carriage bolt = 5/16”-18 x 2”
PERF-O-GRIP J-Clips fasten the grating securely to the
supporting steel without drilling holes.
Standard finish is galvanized.
Hardware is not provided.
Seated J Clip
UPC Number
Catalog Number
Wt./Ea.
78205153667
JCLIP
0.30
Assembly
1. Align PERF-O GRIP planks on I-Beam or other
anchoring cross-member.
2. Place bolt seat on center hole of PERF-O-GRIP
nearest the overhanging end.
3. Align J-Clip below PERF-O-GRIP plank so that the
carriage bolt can slide through. Make sure the
lower lip of the J-Clip reaches well into the I-Beam.
4. Run the carriage bolt through the bolt seat to the
J-Clip and tighten securely with the washer and nut.
5. Test for movement or slippage. If PERF-O GRIP
planks are not secure, check fastening system for
loose or missing parts. Repeat steps 1 thru 4.
Note: Do not walk on PERF-O GRIP planks if
they are not secure. Serious injury could result.
Welding
A common method of fastening safety grating is
welding. It is recommended that all B-Line Safety
Grating products be fillet welded per AWS D1.3.
For more information, consult Technical Services.
14
PERF-O GRIP Grating
Accessories
PERF-O GRIP™ Mid Support Clip with Hardware
Part Number Includes
(1) Clip & (2) Set Screws
Mid Support Clip (with hardware)
UPC Number
Catalog Number
Wt./Ea.
66251639386
MSCLIP
0.50
PERF-O-GRIP mid support clips can be used at midspan
to increase load carrying capacities of individual
channels by fastening several planks together to form
an integral section. Mid support clip is manufactured
from galvanized steel and includes two set screws.
Assembly
1. Align PERF-O GRIP planks on I-Beam or other
anchoring cross-member.
2. Place clip around the bottom flanges of the
PERF-O GRIPS planks.
3. Slide to the required location.
4. Tighten the set screws.
5. Test for movement or slippage. If PERF-O GRIP
planks are not secure, check fastening system for
loose or missing parts. Repeat steps 1 thru 4 as
required.
Note: Do not walk on PERF-O GRIP planks if
they are not secure. Serious injury could result.
Welding
A common method of fastening safety grating is
welding. It is recommended that all B-Line Safety
Grating products be fillet welded per AWS D1.3.
For more information, consult Technical Services.
PERF-O GRIP Grating
15
Accessories
PERF-O GRIP™ Splice Plate Kits
Surface Splice Plate Kits
As width increases, grating surface performance
becomes more critical. Thus, for PERF-O GRIP product
widths greater than 12”, use of the grating surface
splice kit is recommended to mechanically join butt
ends of plank sections.
• POG-ES-10 (for 18” wide plank) & POG-ES-13 (for
24” wide plank) includes six (6) each of hardware
shown below.
• POG-ES-16 (for 30” wide plank) & POG-ES-20 (for
36” wide plank) includes eight (8) each of hardware
shown below.
• Hardware included: 3/8” x 1” carriage bolts, 3/8” flat
washers and bolt seats.
POG-ES-10
POG-ES-10 shown
POG-ES-13
POG-ES-16
POG-ES-20
Walkway Splice Plate Kits
Walkway Splice Plates provide continuity when multiple
lengths of PERF-O GRIP are desired. Connections are
reinforced with the addition of splice plates attached to
side channels.
• POG-WS-30 for 24”, 30” and 36” wide walkway.
• Each Kit includes: Two (2) splice plates and
thirty-two (32) each of the following hardware: 1/2” x
11/4” hex bolts, 1/2”-13 hex nuts and 1/2” flat washers.
POG-WS-30
30”
17/8”
33/4” C to C
5
/8”
41/2”
17/8”
3
/4”
POG-WS-30
11 Ga.
16
PERF-O GRIP Grating