DTS1242 bolted tee connector - interface C COOPER POWER SERIES

Screened Separable

Connectors

CA650046EN

Effective May 2015

Supersedes I550-60 April 2012

COOPER POWER

SERIES

DTS1242 bolted tee connector - interface C

Application

For connection of polymeric cable to transformers, switchgear, motors and other equipment with a premoulded separable connector

For indoor and outdoor installations

System voltage up to 42 kV

Continuous current rating up to 1250 A when installed on an appropriate equipment bushing

Cable particulars:

Polymeric cable (XLPE, EPR, etc.)

Copper or aluminum conductors

Semiconducting or metallic screens

Conductor size: 24 kV 120-800 mm 2

36 kV 95-800 mm 2

Features

Provides a fully screened and fully submersible separable connection when mated with the proper bushing or plug

Built-in capacitive test point allows for an easy check of the circuit status

Available with either DIN compression lugs or mechanical (shear bolt) lugs

No minimum phase clearance requirements

Mounting can be vertical, horizontal, or any angle in between

100% factory tested

Standards

Meets the requirements of IEC 60502-4 and

CENELEC HD 629.1 S2

Quality assurance

Our manufacturing facility is registered to ISO

9001 by third party audit

Required Production Tests

Periodic X-Ray Analysis

Installation

No special tools, heating, taping, or potting are required

Connector may be energized immediately after installation on its mating part

Mates with bushings, plugs, and junction devices complying with CENELEC EN 50180 and 50181

Catalog Data CA650046EN

Effective May 2015

Features and detailed description

1

3

4

7

5

8

6

DTS1242 bolted tee connector - interface C

9

10

11

12

2

1. Clamping Screw

Tin-plated brass screw and brass nut secures the bolted tee conductor contact with the bushing

2. Insulation

Moulded EPDM insulating rubber is formulated and mixed in-house to ensure high quality

3. Basic Insulating Plug

Moulded epoxy part has a threaded metal insert to accept the clamping screw

4. Capacitive Test Point

Capacitive test point provides means to check circuit status.

5. Rubber Cap

Moulded EPDM conducting rubber cap protects and earths the test point during normal operation

6. Internal Screen

Moulded EPDM conducting rubber screen controls electrical stress

7. Capacitive Test Point (Optional)

Capacitive Test point provides a means to check circuit status. A moulded EPDM conducting rubber cap provides a watertight seal.

8. Stress Relief

The configuration of the outer screen and the cable adapter provide cable stress relief

9. Cable Adapter

The sized opening provides an interference fit to maintain a watertight seal and provides the initial cable stress relief

10. Earthing Eyes

Moulded into the external screen for connection of an earthing wire

11. External Screen

Moulded EPDM conducting rubber provides protective deadfront shield.

12. Conductor Contact

Inertia welded bimetallic compression or mechanical (shear bolt) lug accepts copper or aluminum conductors.

Figure 1. 1250 A, 42 kV Class DTS1242 bolted tee connector.

Table 1. Electrical Ratings

DTS1242

Max. Rated System Voltage (U m

)

Basic Impulse Level

AC Voltage Withstand (5 min.)

42 kV

200 kV

93.5 kV

125 kV DC Voltage Withstand (15 min.)

Continuous Current

Thermal Short Circuit, 3 sec.

1250 A

45 kA

Dynamic Short Circuit 100 kA

N otee: Ratings are based on IEC Standards and do not reflect maximum capability.

2 www.eaton.com/cooperpowerseries

DTS1242 bolted tee connector - interface C

54 mm

103 mm

96 mm

205 mm

152 mm

350 mm

75 mm

Figure 2. DTS1250 bolted tee connector dimensional information.

Catalog Data CA650046EN

Effective May 2015

Kit contents

The complete kit includes: moulded tee housing, cable adapter, conductor contact, insulating plug, rubber cap, clamping screw, lubricant, wipers and installation instructions.

Ordering information

To order a 42 kV bolted tee connector, use the Catalog Number

Section Guide, on page 4 and select the cable insulation range from Table 2, which gives you the best centering of the insulation diameter and then select the conductor size from Table 3.

Ordering Examplee: For a 36 kV drain wire shielded cable with a 500 mm2 aluminum conductor, 44 mm core insulation diameter and a DIN style crimp connector in a single-phase kit with a test point, including the cable sealing kit, specify

DTS1242FU500N1T1 .

Table 2. Cable Range

Insulation Range

Designation

C

D

E

A

B

F

G

H

Cable Insulation Range Dia. (mm)

Min.

28.2

31.1

35.0

37.2

40.1

42.9

46.5

50.0

Max.

32.3

35.7

39.1

41.6

44.8

47.9

51.9

56.0

Table 3. Conductor Size

Conductor

Size (mm2) DIN Type

185

240

300

95

120

150

400

500

630

800

U095

U120

U150

U185

U240

U300

U400

U500

-

U630

Mechanical Type

S300

S800

S630

www.eaton.com/cooperpowerseries 3

Catalog Data CA650046EN

Effective May 201

Catalog number selection guide

D T S 1 2 4 2

DTS1242 bolted tee connector - interface C

F U 5 0 0 N 1 T 1

Basic Catalog Number Insulation Range Table 2

Connector Size Table 3

T = Test Point

N = No Test Point

1 = 1-phase kit

3 = 3-phase kit

Cable Sealing Kit

See Table 4

Table 4. Cable Sealing Kits

Description

T1 Basic tape kit with sealing mastic and tape for one single core cable with copper screen wires (3 tape kits included with 3-phase kit)

N otee: For other cable sealing kits, please contact your Eaton representative.

Eaton

1000 Eaton Boulevard

Cleveland, OH 44122

United States

Eaton.com

Eaton’s Cooper Power Systems Division

2300 Badger Drive

Waukesha, WI 53188

Eaton.com/cooperpowerseries

© 2015 Eaton

All Rights Reserved

Printed in USA

Publication No. CA650046EN

Eaton and Cooper Power are valuable trademarks of Eaton in the U.S. and other countries. You are not permitted to use these trademarks without the prior written consent of Eaton.