Deadbreak Connectors
Catalog Data
CA650049EN
Effective May 2015
Supersedes 600-65 May 2002
COOPER POWER
SERIES
600 A 35 kV class PUSH-OP™
insulated standoff bushing
General
Eaton meets the full requirements of IEEE Std
386™-2006 standard – Separable Insulated
Connector Systems in its Cooper Power™ series
600 A, 35 kV PUSH-OP™ insulated standoff
bushing providing a single deadbreak interface
made of high quality insulating epoxy material.
It is used in switchgear, trans­form­ers, and
other apparatus to isolate and sectionalize an
energized cable. Temporary or permanent parking
of energized 600 A 35 kV PUSH-OP deadbreak
con­nec­tors is simplified with the use of an
insulated standoff bushing.
The PUSH-OP insulated standoff bushing is
de­signed to be installed in the parking stand
mounted on switch­gear, transformers, or other
apparatus. A drain wire lug is pro­vid­ed on the
standoff bracket for at­tach­ment of a drain wire
to ensure deadfront construction. The bushing
provides a fully shielded, submersible connection
for deadbreak operation.
All standoff bushing brackets have a stainless
steel eyebolt with a brass pressure foot. The
bushing body is bolted to a stainless steel base
bracket using a stainless steel bolt. The bracket
and latch mechanism provides easy installation
of a PUSH-OP connector without any threading
operations. Optional hitch pin locks the latch
mechanism in place for added security.
Installation
A clampstick tool is used to place the standoff
bushing in the parking stand on the front plate of
the apparatus. The PUSH-OP connector is then
installed onto the standoff bushing tap. Refer to
Service Information S600-65-1 600 A 15/25 and
35 kV Class PUSH-OP Insulated Standoff Bushing
Installation Instructions for complete in­stal­lation
details on the PUSH-OP insulated standoff
bushing.
Catalog Data CA650049EN
600 A 35 kV class PUSH-OP insulated standoff bushing
Effective May 2015
5.8"
(147 mm)
EYEBOLT
Stainless steel eyebolt
with brass pressure foot
rigidly secures standoff
bushing to parking stand.
PULLING EYE
Stainless steel eye
facilitates clampstick
operation with no
additional tool required.
HITCH PIN
(optional) The hitch pin locks
the latch mechanism in place
for added security.
12.37"
(314 mm)
STAINLESS STEEL
BRACKET ASSEMBLY
Stainless steel
mounting bracket
has drain wire lug
for bracket and shield
grounding.
STAINLESS STEEL
BRACKET
AND LATCH MECHANISM
Accepts 600 A PUSH-OP Connectors
and facilitates "threadless" operability.
EPOXY INSULATION
High quality molded
epoxy insulation provides
excellent electrical,
thermal and mechanical
reliability for insulated
standoff bushings.
2.88"
(73 mm)
DRAIN WIRE LUG
Provided for attachment
of drain wire lead.
6.0"
(152 mm)
3.76"
(96 mm)
6.27"
(159 mm)
FRONT VIEW
SIDE VIEW
Figure 1. Front view shows standoff bushing and latch mechanism. Side view shows standoff bushing and latch mechanism with
bracket assembly.
NNote: Dimensions given are for reference only.
S8
S7
TANK
WALL
S7
S8
35 kV
0.75" (19 mm)
6.8" (173 mm)
Figure 2. PUSH-OP stacking dimensions.
2
www.eaton.com/cooperpowerseries
Catalog Data CA650049EN
600 A 35 kV class PUSH-OP insulated standoff bushing
Effective May 2015
Production tests
Ordering information
Tests conducted in accordance with IEEE Std 386™-2006 standard:
To order a 35 kV Class Stand­off Bushing Kit for PUSH-OP refer to
Table 2.
•
•
ac 60 Hz 1 Minute Withstand
• 50 kV
Table 2. Standoff Bushing Kit
Minimum Corona Voltage Level
• 26 kV
Tests conducted in accordance with Eaton re­quire­ments:
•
Physical Inspection
•
Periodic Fluoroscopic Analysis
Description
Catalog Number
Insulated Standoff Bushing
PISB635
Insulated Standoff Bushing with hitch pin
PISB635HP
Each kit contains:
Table 1. Voltage Ratings and Characteristics – Insulated
Standoff Bushing
Description
kV
Standard Voltage Class
35
Maximum Rating Phase-to-Ground
21.1
ac 60 Hz 1 Minute Withstand
50
dc 15 Minute Withstand
103
BIL and Full Wave Crest
150
Minimum Corona Voltage Level
26
•
Standoff Bushing with Bracket
•
Shipping Cap (not for energized operation)
•
Silicone Lubricant
•
Installation Instruction Sheet
Voltage ratings and characteristics are in accordance with IEEE Std 386™-2006 standard.
www.eaton.com/cooperpowerseries
3
Catalog Data CA650049EN
600 A 35 kV class PUSH-OP insulated standoff bushing
Effective May 2015
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Cooper Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. CA650049EN
Eaton, Cooper Power, and PUSH-OP are
valuable trademarks of Eaton in the U.S. and
other countries. You are not permitted to use
these trademarks without the prior written
consent of Eaton.
IEEE Std 386™-2006 standard is a trademark
of the Institute of Electrical and Electronics
Engineers, Inc., (IEEE). This publication is not
endorsed or approved by the IEEE.
For Eaton's Cooper Power series PUSH-OP
bushing product information
call 1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.