Tribute (Door Accessories)
Sheet 1 of 2
INSTALLATION INSTRUCTIONS
6/2/09
IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.
IMI-690
WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.
WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.
WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.
WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly.
Tighten all fixture components to their recommended torque values.
WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture. Install right side up.
Tools Required 5/16” socket,
(Phillips driver #1 for 4S shield)
NOTE: These luminaires are designed for
outdoor lighting services, and should not be
used in area of limited ventilation or in high
ambient temperature enclosures.
Construction is suitable for down lighting
only. Best results will be obtained if
installed and maintained according to the
following recommendations.
1. Open housing and remove door per the
installation instructions by squeezing
thumb latch towards front of housing.
Door is removed by opening it to a 45°
position and lifting it off the hinges.
INTERNAL HOUSE SIDE SHIELDS
MA1222 [Internal House Side Shield for 2S and 3S Optics]
Relative Position of Shield
to Lamp Socket
Internal House Side
Shield Installed to inside of Door
2. Install shield on back side of door by MA1223 [Internal House Side Shield for 4S Optics]
loosening the two (2) glass hold down
clamps. Slide the shield under clamps
and tighten. Installing two (2) more
clamps as shown. Make sure the
shield is oriented to the socket per
the diagram.
3. Replace door on hinges and push
closed until latch snaps into place.
Internal House Side
Shield Installed to inside of Door
MA1224 [Internal House Side Shield for 2F and 3F Optics]
Internal House Side
Shield Installed to inside of Door
Relative Position of Shield
to Lamp Socket
(2) Small Screw
Relative Position of Shield
to Lamp Socket
Shield added to Reflector
MA1225 [Internal House Side Shield for 4F Optics]
Relative Position of Shield
to Lamp Socket
Louvers
Towards Lamp
Internal House Side
Shield Installed to inside of Door
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.
NOTE: Specifications and dimensions subject to change without notice.
Visit our web site at www.cooperlighting.com
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801
ADH071656
Tribute (Door Accessories)
Sheet 2 of 2
INSTALLATION INSTRUCTIONS
IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.
6/2/09
IMI-690
WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.
WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.
WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.
WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly.
Tighten all fixture components to their recommended torque values.
WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture. Install right side up.
Tools Required 5/16” socket
NOTE: These luminaires are designed for
outdoor lighting services, and should not be
used in area of limited ventilation or in high
ambient temperature enclosures.
Construction is suitable for down lighting
only. Best results will be obtained if
installed and maintained according to the
following recommendations.
EXTERNAL HOUSE SIDE SHIELD OR VANDAL SHIELD
MA1221 [External House Side Shield]
1. Open housing and remove door per the
installation instructions by squeezing
thumb latch towards front of housing.
Door is removed by opening it to a 45°
position and lifting it off the hinges.
2. Install External House Side Shield
[MA1221] with four (4) supplied screws.
Holes are provided to rotate the shield in
four (4) different mounting positions.
Install Vandal Shield [TR/VS] as shown
with provided screws and spacers.
TR/VS [Vandal Shield]
3. Replace door on hinges and push
closed until latch snaps into place.
(4) 2” Spacers
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.
NOTE: Specifications and dimensions subject to change without notice.
Visit our web site at www.cooperlighting.com
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801
ADH071656