Commercial Products
Approved for ARRA Funding
American Recovery and Reinvestment Act (ARRA)
ARRA Certified Product Solutions
Cooper Crouse-Hinds Commercial Products offers a broad array of products that can be used in ARRA funded construction projects,
such as:
• Military Facilities
• Wastewater Treatment Plants
• Infrastructure (roadways / bridges / tunnels / parking
• Municipal Government Facilities
• Educational Facilities
garages / docks and piers)
• Healthcare Facilities
• Power Plants
Our Commercial Products offering is an extensive mix of products and accessories used to connect, support, turn, and provide
access to wiring systems. The following page highlights a selection of products commonly found throughout construction projects.
Each of the product families listed contain items approved for ARRA financial stimulus spending. For more information on our full
product line offering, please refer to the Cooper Crouse-Hinds Product Catalog.
COMMERCIAL PRODUCTS
Fiberglass
Enclosures*
W Series Junction
Boxes*
Made in USA Steel EMT
Fittings*
Designed to hold up
under the most extreme
conditions and provide
protection in adverse
environments, this
extensive selection of corrosion-resistant nonmetallic enclosures delivers superior
performance and provides a wide range of
options to meet any customer preference.
Cast iron, hot dipped
galvanized enclosures are
ideal for highway, bridge,
and other infrastructure construction
projects and provide space for
pulling conductors and ease of maintenance.
Often encased in concrete, these boxes stand up
to years of use and installation.
Connectors and couplings
for applications where
“Made in the USA” is
required, such as military
bases and installations, government buildings,
prisons, and various federally funded stimulus
projects.
• NEMA 4X
PRE-formance™*
PRE-formance products are pre-fabricated
solutions
that allow
contractors to better
control their labor allocation and reduce total
installation and construction costs. Improve
job site efficiency and properly align skilled
resources to meet tight commercial
construction project deadlines.
™
SmartGuard and MetalGuard
Protective Plates*
™
These high
impact, router
resistant
protection plates
keep electrical
and communication boxes clean and free from
debris during construction projects, greatly
reducing expensive and non-productive
callbacks and re-works.
• NEMA 3
• NEMA 4 (WCB, WJB, WJBF only) watertight
• H-20 vehicle load rating (WAB, WJB, WJBF
only)
Solar Combiner
Boxes*
Used to group input
wires/circuits from several arrays and/or solar
panels. The combined circuit results in fewer
output circuits and combines them into one main
buss or feed going to the inverter, saving labor
and material costs. Designed for higher voltage
circuits used in grid tie applications.
• NEMA 4X (fiberglass and stainless steel)
• NEMA 3R (painted steel)
Stainless Steel Fittings*
LTK Series Liquidtight
Fittings*
LTK Series Liquidtight Fittings
are designed specifically for
applications which require
close side-by-side mounting
of multiple liquidtight fittings in tight spaces.
• Steel body and malleable gland nut with
zinc electroplate finish for long, dependable
service
Steel Outlet Boxes
and Plaster Rings*
Provide an easy method for
the installation of electrical
devices, such as switches,
fans, receptacles, fixtures, etc. Rugged steel
plaster rings used with outlet boxes ensure that
the boxes fit flush with the drywall.
Provide five times the strength
and three times the lifespan of
a typical cast aluminum fitting.
Unbeatable corrosion
resistance and extreme strength make these
fittings ideal for construction projects.
• Cl. I, Div. 2 per NEC® Article 501.10(B)(4)
• Available in 18-gauge steel
For more information, please log onto www.cooperindustries.com/markets/stimulus/.
*This product family listing is for informational purposes only and does not provide country of origin. This is not certification that each item in the product families listed satisfy the requirements of
any applicable free trade agreements or the Buy American Provision (Section 1605) of the American Recovery and Reinvestment Act (ARRA). This also does not certify that the steel used is of U.S.
origin. For certification, please contact Cooper Crouse-Hinds Customer Service at (866) 764-5454 to ensure that the specific part numbers and sizes required will meet any necessary compliance.
Cooper Crouse-Hinds
P.O. Box 4999
Syracuse, NY 13221
Toll Free: (866) 764-5454
Fax: (315) 477-5179 FAX Orders Only: (866) 653-0640
crouse.customerctr@cooperindustries.com
4976-0310
Printed in USA