EOL SERIES (L-810) OBSTRUCTION LIGHT SINGLE AND DOUBLE FIXTURE IF 1556 INSTALLATION INSTRUCTIONS AND PARTS LIST SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE INSTALLATION - SINGLE HEAD UNITS WARNING De-energize circuit before relamping or working on fixture (A) Single fixtures as supplied are fully assembled with the exception of the lamp. To install or replace the lamp (7), remove the clamp band (5) and globe (4). The globe (4) can be supported by the supplied attached tether. Inspect o-ring (2) and other internal components and replace as necessary. (B) Assemble the locknut (13) to the mounting column (20) (see figure 1) with the notched locking surface on the top side and threaded on to a depth of one inch. Connect wires (9, 10 and if GR or -CSA version, item 11) to the appropriate source. (NOTE: white wire (9) is connected to the lamp socked shell (8)). (C) For P/N 40940, position the fixture on the mounting column (20) (See figure 1) and loosen the three binding screws (6) half a turn. Thread only the globe support hub (12) (to avoid twisting wires) to full thread depth and secure the locknut (13). With the globe support (1) fully bottomed on the hub (12), tighten all three binding screws (6). FIGURE - 1 P/N 40940 (D) For P/N 50033, insert 90° elbow (14) into globe support (1) (see figure 2). With the globe support (1) fully bottomed on the elbow (14), tighten all three binding screws (6). FIGURE 3 - P/N 50021 FIGURE 2 - P/N 50033 All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or completeness thereof are not guaranteed. In accordance with Crouse-Hinds "Terms and Conditions of Sale", and since conditions of use are outside our control, the purchaser should determine the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith. Cooper Industries Inc. Crouse-Hinds Division PO Box 4999, Syracuse, New York 13221 • U.S.A. Copyright© 2008, Cooper Industries, Inc. IF 1556 Rev 1 New 2/08 Page 1 INSTALLATION - DOUBLE FIXTURE P/N 50021 (A) Lamp and globe assembly is the same as the single fixture procedure. (B) Remove housing cover (18) from condulet housing (17). Position one light fixture at either end of condulet housing and feel lead wires into the center section of housing. Thread light fixture into end of housing as far as it will go, aligning light fixture in a vertical position. Do this for both fixtures then re-assemble cover (18) to condulet housing (17). FIGURE 4 - GROUNDING WIRE (-GR) PARTS LIST PART NO. 40940 - OBSTRUCTION LIGHT, L- 810 SINGLE PART NO. 50021 - OBSTRUCTION LIGHT, L- 810 DOUBLE PART NO. 50033 - OBSTRUCTION LIGHT, L- 810 SINGLE SIDE HUB ITEM NO. * * 1 2 3 * 4 * * * 5 6 7 * * * * * * * 8 9 10 11 12 13 14 15 13 17 18 19 20 PART NO. 40948 10035-37 10048-37 50131-R 50131-B 50131-Y 50131-G 50131-C 50107 10A10-025D24 10047-1558 10047-1577 10047-2145 10047-1559 50030W 50030 50095 40936 10037-322 10037-332 50098-1 50083 10037-326 10037-571 10H27-013D10 NOT SUPPLIED QTY 1 1 A/R 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 DESCRIPTION GLOBE SUPPORT SEAL RTV, CLEAR GLOBE & TETHER ASSY, RED GLOBE & TETHER ASSY, BLUE GLOBE & TETHER ASSY, YELLOW GLOBE & TETHER ASSY, GREEN GLOBE & TETHER ASSY, CLEAR CLAMP BAND SCREW, HEX HD., TYPE F, 1/4-20 X 3/4” LONG LAMP, 69 WATT, 120 VOLT LAMP, 116 WATT, 120 VOLT LAMP, 116 WATT, 230 VOLT SOCKET, LAMP WIRE ASSY, #16 AWG, WHITE WIRE ASSY, #16, BLACK GROUND WIRE ASSY (-GR & -CSA) HUB, GLOBE SUPPORT LOCKNUT (1.00”) ELBOW, 90° MALE / FEMALE INSULATOR, SOCKET (-CSA) NIPPLE, 1” NPT - ONE END ONLY HOUSING, CONDULET COVER, SNAPTIGHT SCREW, RD. HD., #6-32X5⁄16, SELF-TAP TYPE “F” SST MOUNTING COLUMN * - DESIGNATES THESE ITEMS TO HAVE THE QUANTITY DOUBLED FOR USE ON A 50021 LIGHT Cooper Industries Inc. Crouse-Hinds Division PO Box 4999, Syracuse, New York 13221 • U.S.A. Copyright© 2008, Cooper Industries, Inc. IF 1556 Rev 1 New 2/08 Page 2