Voltage Regulators
Technical Data
TD225005EN
Effective XXX 2015
Supersedes 240-40 August 2012
COOPER POWER
SERIES
Communications Point Data Base
for Communications Protocol IEC60870-5
For use with Eaton’s Cooper Power series
CL-7 Voltage Regulator Control
CL-7 IEC 60870-5 Device Profile Data Dictionary
CL-7 IEC 60870-5 Map Points
June 3, 2015
v2.00
THE INFORMATION CONTAINED IN THIS DOCUMENT IS THE PROPERTY OF EATON.
UNAUTHORIZED REPRODUCTION OR MODIFICATION IS PROHIBITED.
Document
1.00
2.00
Date
4/29/2013
6/3/2015
Description
Initial Release
Updates for Summer 2015 release
This document references the "CL7 Default" point map available in the ProView NXG software.
Point Numbering Convention
IEC 60870-5 data points consist of 7 main types: single input, double input, measured values, single command, double command,
floating point, and integrated totals. The numbering convention refers to the individual data points by prefixing their addresses so that
when looking at a number for a given point the user would know which type of data point was being referenced.
Data type
Single input
Double input
Measured Value
Single command
Floating Point
Base Address
1
4096
8192
12288
16384
Note: The CL-7 does not have any Double Input or Floating Point points defined.
Page 1
Cover Page
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Single Inputs
Base Address: 1
Description
VR1 Bandwidth Low
VR1 Bandwidth High
VR1 Voltage Limiter Low
VR1 Voltage Limiter High
Voltage Reduction Active
VR1 Auto Operation Blocking Status Blocked (Follows FC069)
VR1 HMI LED Auto Tap Blocked ON
VR1 System Power Direction Indeterminate
VR1 System Power Direction Reverse
VR1 Control Power Direction Reverse
VR1 Blocking Relay Active
VR1 HMI LED Neutral Position On
VR1 HMI Switch Auto/Manual Auto
HMI Switch Supervisory Off
HMI LED Alarm On
HMI LED Warning On
HMI LED Diagnostic Error On
VR1 Motor Trouble
Tap To Neutral Active
Soft Add-Amp Active
AltConfigActive
Configurable Logic Output from SCADA Tap to Neutral Activate
Configurable Logic Output from SCADA Voltage Reduction Level 1 Activate
Configurable Logic Output from SCADA Voltage Reduction Level 2 Activate
Configurable Logic User Defined LED 1 On
Configurable Logic User Defined LED 2 On
Configurable Logic User Defined LED 3 On
Configurable Logic Point 01 to SCADA
Configurable Logic Point 02 to SCADA
Configurable Logic Point 03 to SCADA
Configurable Logic Point 04 to SCADA
Offset
Hex Offset
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
Page 2
Single Inputs, Single Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Measured Values
Base Address: 8192
Description
VR1 Load Voltage Secondary
VR1 Load Voltage Primary
VR1 Compensated Voltage Secondary
VR1 Load Current Primary
VR1 Source Voltage Secondary
VR1 Source Voltage Primary
VR1 Tap Position
VR1 Percent Reg
VR1 Power Factor
VR1 KVA Load
VR1 kW Load
VR1 KVAR Load
Frequency
VR1 Harm Total Voltage Harmonics
VR1 Harm Total Current Harmonics
VR1 kWh Forward
VR1 KWH Reverse
VR1 KQH Forward
VR1 KQH Reverse
VR1 Operation Counter
VR1 Load Current Real
VR1 Load Current Reactive
VR1 Phase Angle
Voltage Reduction In Effect
Active Configuration
Active Adaptive Add Amp Level
VR1 Operations Counter
VR1 Operations 24HR Counter
VR1 Operations 30DY Counter
VR1 Operations Month Counter
VR1 Operations Last Month Counter
VR1 Operations Year Counter
VR1 Operations Last Year Counter
VR1 TPI Neutral Resynch Counter
VR1 Lower to Neutral Sync Retry Counter
VR1 Raise to Neutral Sync Retry Counter
VR1 Taps Past 16R Counter
VR1 Taps Past 16L Counter
Measured/Incremental TPI Mismatch Count
Offset
Hex Offset
Division
Scale Factor
Default
Deadband
Units
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
10
100
10
10
10
100
1
10
1000
10
10
10
100
10
10
100
100
100
100
1
10
10
1
10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1000
1000
1000
1000
1000
1000
1000
10000
10000
10000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
500
1000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
Volts
kVolts
Volts
Amps
Volts
kVolts
-%
-kVA
kW
kvar
Hz
%
%
kWHr
kWHr
kvarHr
kvarHr
-Amps
Amps
Degrees
%
%
---------------
Page 3
Low Limit High Limit
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
Measured Values, Single Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Measured Values
Base Address: 8192
Description
COM1 Rx Message Counter
COM2 Rx Message Counter
COM1 Tx Message Counter
COM2 Tx Message Counter
COM1 Message Error Counter
COM2 Message Error Counter
Offset
Hex Offset
Division
Scale Factor
Default
Deadband
Units
39
40
41
42
43
44
27
28
29
2A
2B
2C
1
1
1
1
1
1
10000
10000
10000
10000
10000
10000
-------
Page 4
Low Limit High Limit
10
10
10
10
10
10
10000
10000
10000
10000
10000
10000
Measured Values, Single Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
OUTPUT SUBSYSTEM
Single Commands
Base Address: 12288
Description
VR1 Raise Tap *
VR1 Lower Tap *
Auto Block Enable
VR1 Source Side Voltage Calculation
Interval Operations Counters Enable
VR1 Operations Counter Month Reset *
VR1 Operations Counter Year Reset *
VR1 Operations Counter 24HR Reset *
VR1 Operations Counter 30DY Reset *
VR1 Operations Counter Last Month Reset *
VR1 Operations Counter Last Year Reset *
VR1 TPI Neutral Mismatch Reset *
VR1 Lower To Neutral sync Retry Count Reset *
VR1 Raise To Neutral Sync Retry Count Reset *
VR1 Taps Past 16L Counter Reset *
VR1 Taps Past 16R Counter Reset *
Rx COM1 Counter Reset *
Rx COM2 Counter Reset *
Tx COM1 Counter Reset *
Tx COM2 Counter Reset *
Message Error COM1 Counter Reset *
Message Error COM2 Counter Reset *
Reset Energy All *
Reset All Demand Values *
Sequence of Events Enable
Data Profiler Enable
Data Profiler Snapshot *
Tap To Neutral Feature Enable
PMT Mode A Enable
PMT Mode B Enable
PMT Mode A Test *
PMT Mode B Test *
Data Alarms Enable
Status Alarms Enable
VR1 Time On Tap Reset *
Top Side Port LoopShare Enabled
Bottom Side Port LoopShare Enabled
Leader/Follower Enable
Offset
Hex Offset
Supervisory
Enable
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Page 5
Single Commands, Single Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
OUTPUT SUBSYSTEM
Single Commands
Base Address: 12288
Description
Configurable Logic Output from SCADA Tap to Neutral Activate
Configurable Logic Output from SCADA Voltage Reduction Level 1 Activate
Configurable Logic Output from SCADA Voltage Reduction Level 2 Activate
Configurable Logic Output from SCADA 1
Configurable Logic Output from SCADA 2
Configurable Logic Output from SCADA 3
Configurable Logic Output from SCADA 4
HMI Remote Security Override Mode
Offset
Hex Offset
Supervisory
Enable
38
39
40
41
42
43
44
45
26
27
28
29
2A
2B
2C
2D
1
1
1
1
1
1
1
1
* Momentary/Self Resetting
Page 6
Single Commands, Single Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Single Inputs
Base Address: 1
Description
VR1 Bandwidth Low
VR2 Bandwidth Low
VR3 Bandwidth Low
VR1 Bandwidth High
VR2 Bandwidth High
VR3 Bandwidth High
VR1 Voltage Limiter Low
VR2 Voltage Limiter Low
VR3 Voltage Limiter Low
VR1 Voltage Limiter High
VR2 Voltage Limiter High
VR3 Voltage Limiter High
Voltage Reduction Active
VR1 Auto Operation Blocking Status Blocked (Follows FC069)
VR2 Auto Operation Blocking Status Blocked
VR3 Auto Operation Blocking Status Blocked
VR1 HMI LED Auto Tap Blocked ON
VR2 HMI LED Auto Tap Blocked ON
VR3 HMI LED Auto Tap Blocked ON
VR1 System Power Direction Indeterminate
VR2 System Power Direction Indeterminate
VR3 System Power Direction Indeterminate
VR1 System Power Direction Reverse
VR2 System Power Direction Reverse
VR3 System Power Direction Reverse
VR1 Control Power Direction Reverse
VR2 Control Power Direction
VR3 Control Power Direction
VR1 Blocking Relay Active
VR1 HMI LED Neutral Position On
VR2 HMI LED Neutral Position On
VR3 HMI LED Neutral Position On
VR1 HMI Switch Auto/Manual Auto
VR2 HMI Switch Auto/Manual Auto
VR3 HMI Switch Auto/Manual Auto
HMI Switch Supervisory Off
HMI LED Alarm On
HMI LED Warning On
HMI LED Diagnostic Error On
VR1 Motor Trouble
VR2 Motor Trouble
VR3 Motor Trouble
Tap To Neutral Active
Soft Add-Amp Active
AltConfigActive
Offset
Hex Offset
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
Page 7
Single Inputs, Multi Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Single Inputs
Base Address: 1
Description
Configurable Logic Output from SCADA Tap to Neutral Activate
Configurable Logic Output from SCADA Voltage Reduction Level 1 Activate
Configurable Logic Output from SCADA Voltage Reduction Level 2 Activate
Configurable Logic User Defined LED 1 On
Configurable Logic User Defined LED 2 On
Configurable Logic User Defined LED 3 On
Configurable Logic Point 01 to SCADA
Configurable Logic Point 02 to SCADA
Configurable Logic Point 03 to SCADA
Configurable Logic Point 04 to SCADA
Offset
Hex Offset
45
46
47
48
49
50
51
52
53
54
2D
2E
2F
30
31
32
33
34
35
36
Page 8
Single Inputs, Multi Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Measured Values
Base Address: 8192
Description
VR1 Load Voltage Secondary
VR2 Load Voltage Secondary
VR3 Load Voltage Secondary
Average Load Voltage Secondary
VR1 Load Voltage Primary
VR2 Load Voltage Primary
VR3 Load Voltage Primary
Average Load Voltage Primary
VR1 Compensated Voltage Secondary
VR2 Compensated Voltage Secondary
VR3 Compensated Voltage Secondary
Average Compensated Voltage Secondary
VR1 Load Current Primary
VR2 Load Current Primary
VR3 Load Current Primary
Average Load Current Primary
VR1 Source Voltage Secondary
VR2 Source Voltage Secondary
VR3 Source Voltage Secondary
Average Source Voltage Secondary
VR1 Source Voltage Primary
VR2 Source Voltage Primary
VR3 Source Voltage Primary
Average Source Voltage Primary
VR1 Tap Position
VR2 Tap Position
VR3 Tap Position
Average Tap Position
VR1 Percent Reg
VR2 Percent Reg
VR3 Percent Reg
Average Percent Reg
VR1 Power Factor
VR2 Power Factor
VR3 Power Factor
Average Power Factor
Regulator Tap Position Sync Count
VR2 KVA Load
VR3 KVA Load
Total KVA Load
VR1 kW Load
VR2 kW Load
VR3 kW Load
Total kW Load
VR1 KVAR Load
Offset
Hex Offset
Division
Scale Factor
Default
Deadband
Units
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
10
10
10
10
100
100
100
100
10
10
10
10
10
10
10
10
10
10
10
10
100
100
100
100
1
1
1
1
10
10
10
10
1000
1000
1000
1000
1
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
1
10
10
10
10
10
10
10
1
1
1
10
10000
10
10
10
10
10
10
10
10
Volts
Volts
Volts
Volts
kVolts
kVolts
kVolts
kVolts
Volts
Volts
Volts
Volts
Amps
Amps
Amps
Amps
Volts
Volts
Volts
Volts
kVolts
kVolts
kVolts
kVolts
----%
%
%
%
-----kVA
kVA
kVA
kW
kW
kW
kW
kvar
Page 9
Low Limit High Limit
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
Measured Values, Multi Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Measured Values
Base Address: 8192
Description
VR2 KVAR Load
VR3 KVAR Load
Total KVAR Load
Frequency
VR1 Harm Total Voltage Harmonics
VR2 Harm Total Voltage Harmonics
VR3 Harm Total Voltage Harmonics
VR1 Harm Total Current Harmonics
VR2 Harm Total Current Harmonics
VR3 Harm Total Current Harmonics
VR1 kWh Forward
VR2 kWh Forward
VR3 kWh Forward
Total kWh Forward
VR1 KWH Reverse
VR2 KWH Reverse
VR3 KWH Reverse
Total KWH Reverse
VR1 KQH Forward
VR2 KQH Forward
VR3 KQH Forward
Total KQH Forward
VR1 KQH Reverse
VR2 KQH Reverse
VR3 KQH Reverse
Total KQH Reverse
VR1 Operation Counter
VR2 Operation Counter
VR3 Operation Counter
HMI Last Self-Test Results
VR1 Load Current Real
VR2 Load Current Real
VR3 Load Current Real
Average Load Current Real
VR1 Load Current Reactive
VR2 Load Current Reactive
VR3 Load Current Reactive
Average Load Current Reactive
VR1 Phase Angle
VR2 Phase Angle
VR3 Phase Angle
Voltage Reduction In Effect
Active Configuration
Active Adaptive Add Amp Level
VR1 Operations Counter
VR2 Operations Counter
Offset
Hex Offset
Division
Scale Factor
Default
Deadband
Units
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
10
10
10
100
10
10
10
10
10
1
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
1
1
1
1
10
10
10
10
10
10
10
10
1
1
1
10
1
1
1
1
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
kvar
kvar
kvar
Hz
%
%
%
%
%
%
kWHr
kWHr
kWHr
kW
kWHr
kWHr
kWHr
kW
kvarHr
kvarHr
kvarHr
kvar
kvarHr
kvarHr
kvarHr
kvar
----Amps
Amps
Amps
Amps
Amps
Amps
Amps
Amps
Degrees
Degrees
Degrees
%
%
----
Page 10
Low Limit High Limit
10
0
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
Measured Values, Multi Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
INPUT SUBSYSTEM
Measured Values
Base Address: 8192
Description
VR3 Operations Counter
VR1 Operations 24HR Counter
VR2 Operations 24HR Counter
VR3 Operations 24HR Counter
VR1 Operations 30DY Counter
VR2 Operations 30DY Counter
VR3 Operations 30DY Counter
VR1 Operations Month Counter
VR2 Operations Month Counter
VR3 Operations Month Counter
VR1 Operations Last Month Counter
VR2 Operations Last Month Counter
VR3 Operations Last Month Counter
VR1 Operations Year Counter
VR2 Operations Year Counter
VR3 Operations Year Counter
VR1 Operations Last Year Counter
VR2 Operations Last Year Counter
VR3 Operations Last Year Counter
VR1 TPI Neutral Resynch Counter
VR2 TPI Neutral Resynch Counter
VR3 TPI Neutral Resynch Counter
VR1 Lower to Neutral Sync Retry Counter
VR2 Lower to Neutral Sync Retry Counter
VR3 Lower to Neutral Sync Retry Counter
VR1 Raise to Neutral Sync Retry Counter
VR2 Raise to Neutral Sync Retry Counter
VR3 Raise to Neutral Sync Retry Counter
VR1 Taps Past 16R Counter
VR2 Taps Past 16R Counter
VR3 Taps Past 16R Counter
VR1 Taps Past 16L Counter
VR2 Taps Past 16L Counter
VR3 Taps Past 16L Counter
Regulator Tap Position Sync Count
COM1 Rx Message Counter
COM2 Rx Message Counter
COM1 Tx Message Counter
COM2 Tx Message Counter
COM1 Message Error Counter
COM2 Message Error Counter
Offset
Hex Offset
Division
Scale Factor
Default
Deadband
Units
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
------------------------------------------
Page 11
Low Limit High Limit
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
10000
Measured Values, Multi Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
OUTPUT SUBSYSTEM
Single Commands
Base Address: 12288
Description
VR1 Raise Tap *
VR2 Raise Tap *
VR3 Raise Tap *
VR1 Lower Tap *
VR2 Lower Tap *
VR3 Lower Tap *
Auto Block Enable
VR1 Source Side Voltage Calculation
VR2 Source Side Voltage Calculation
VR3 Source Side Voltage Calculation
Interval Operations Counters Enable
VR1 Operations Counter Month Reset *
VR2 Operations Counter Month Reset *
VR3 Operations Counter Month Reset *
VR1 Operations Counter Year Reset *
VR2 Operations Counter Year Reset *
VR3 Operations Counter Year Reset *
VR1 Operations Counter 24HR Reset *
VR2 Operations Counter 24HR Reset *
VR3 Operations Counter 24HR Reset *
VR1 Operations Counter 30DY Reset *
VR2 Operations Counter 30DY Reset *
VR3 Operations Counter 30DY Reset *
VR1 Operations Counter Last Month Reset *
VR2 Operations Counter Last Month Reset *
VR3 Operations Counter Last Month Reset *
VR1 Operations Counter Last Year Reset *
VR2 Operations Counter Last Year Reset *
VR3 Operations Counter Last Year Reset *
VR1 TPI Neutral Mismatch Reset *
VR2 TPI Neutral Mismatch Reset *
VR3 TPI Neutral Mismatch Reset *
VR1 Lower To Neutral Sync Retry Count Reset *
VR2 Lower To Neutral Sync retry Count Reset *
VR3 Lower To Neutral Sync retry Count Reset *
VR1 Raise To Neutral Sync Retry Count Reset *
VR2 Raise To Neutral Sync Retry Count Reset *
VR3 Raise To Neutral Sync Retry Count Reset *
VR1 Taps Past 16L Counter Reset *
VR2 Taps Past 16L Counter Reset *
VR3 Taps Past 16L Counter Reset *
VR1 Taps Past 16R Counter Reset *
VR2 Taps Past 16R Counter Reset *
VR3 Taps Past 16R Counter Reset *
Rx COM1 Counter Reset *
Offset
Hex Offset
Supervisory
Enable
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Page 12
Single Commands, Multi Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
OUTPUT SUBSYSTEM
Single Commands
Base Address: 12288
Description
Rx COM2 Counter Reset *
Tx COM1 Counter Reset *
Tx COM2 Counter Reset *
Message Error COM1 Counter Reset *
Message Error COM2 Counter Reset *
Reset Energy All *
Reset All Demand Values *
Sequence of Events Enable
Data Profiler Enable
Data Profiler Snapshot *
Tap To Neutral Feature Enable
PMT Mode A Enable
PMT Mode B Enable
PMT Mode A Test *
PMT Mode B Test *
Data Alarms Enable
Status Alarms Enable
VR1 Time On Tap Reset *
VR2 Time On Tap Reset *
VR3 Time On Tap Reset *
Top Side Port LoopShare Enabled
Bottom Side Port LoopShare Enabled
Leader/Follower Enable
Configurable Logic Output from SCADA Tap to Neutral Activate
Configurable Logic Output from SCADA Voltage Reduction Level 1 Activate
Configurable Logic Output from SCADA Voltage Reduction Level 2 Activate
Configurable Logic Output from SCADA 1
Configurable Logic Output from SCADA 2
Configurable Logic Output from SCADA 3
Configurable Logic Output from SCADA 4
Configurable Logic Output from SCADA 5
Configurable Logic Output from SCADA 6
Configurable Logic Output from SCADA 7
Configurable Logic Output from SCADA 8
Offset
Hex Offset
Supervisory
Enable
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Page 13
Single Commands, Multi Phase
CL-7 IEC 60870-5 Device Profile Data Dictionary
OUTPUT SUBSYSTEM
Single Commands
Base Address: 12288
Description
AltConfig1 Auto Block Enable
AltConfig1 Tap To Neutral Feature Enable
AltConfig2 Auto Block Enable
AltConfig2 Tap To Neutral Feature Enable
AltConfig3 Auto Block Enable
AltConfig3 Tap To Neutral Feature Enable
ARL AltConfigTerminate
ARLC Ready
ARLC Activate
Max Deviation Cancel Alt Mode *
Test Battery *
HMI Remote Security Override Mode
Offset
Hex Offset
Supervisory
Enable
79
80
81
82
83
84
85
86
87
88
89
90
4F
50
51
52
53
54
55
56
57
58
59
5A
1
1
1
1
1
1
1
1
1
1
1
1
* Momentary/Self Resetting
Page 14
Single Commands, Multi Phase
Technical Data TD225005EN
Communications
Point Data Base

Effective June 2015
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Cooper Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. TD225005EN
June 2015
Supersedes R225-70-32 (5/2013)
Eaton is a registered trademark.
All other trademarks are property
of their respective owners.
For Eaton's Cooper Power series CL-7 voltage
regulator control information
call 1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.