Concrete Inserts
Continuous concrete inserts, installed in the
ceiling, can be used to support trapeze hangers,
suspended pipe racks, cable trays and single or
multiple pipe hangers.
When installed in walls, continuous concrete
inserts can be used as a support for tunnel
stanchions, equipment braces, brackets and pipe
racks.
Concrete Inserts
Use spot inserts for single pipe-support or
trapeze type hangers. Spot Inserts offer full
flexibility of rod and fastener sizings.
Our channel can be attached to continuous
concrete inserts in walls or ceilings. Channel
can also be attached to concrete walls and
floors with expansion anchors.
Reference page 213 for general fitting and standard finish specifications.
Strut Systems
214
Continuous Concrete Inserts
B22I
Continuous Concrete Insert
15/8”
4”
(41.3)
(101.6)
• Design Load for B22-I-12 thru B22-I-240
is 2,000 lbs. (8.89 kN) per foot of concrete
MATERIAL: 12 Gauge (2.6)
insert length with safety factor of 3 in
11/2”
3000 psi concrete.
(38.1)
• Loads concentrated within the last 2
3/4”
inches (50.8 mm) of concrete inserts
(19.0)
1
3 /8”
8” (203.2 mm) and longer should not
(79.4)
exceed 1,000 lbs. (4.45kN).
• Concrete insert should be secured to the
.188 Knockouts For
forms on 16” (406.4 mm) to 24” (609.6 mm)
Nailing Inserts To
11
B22-I-3 Thru
/16”
intervals.
Forms
(17.4)
B22-I-8
• B22-I continuous concrete inserts are
made from B22 channel. Use channel
25/8” 15/8”
Styrofoam
nuts designed for use in B22 channel.
15/8”
(66.7)
Filler
(41.3)
• B22-I concrete inserts are supplied with
(41.3)
styrofoam fillers. B3322 end caps are
furnished with inserts through 8” (203.2 mm)
long, and B205 end caps are furnished
with inserts 12” (304.8 mm) and longer.
15/8”
• Material: Plain Steel ASTM A1011
(41.3)
33,000 PSI min. yield or Pre-Galvanized
Steel ASTM A653SS 33,000 PSI min.
Styrofoam
B3322
yield.
Filler
End Cap
• Finish: Plain, DURA GREEN™, Pre-Galv,
B205 End Cap
HDG
B22-I-12 THRU B22-I-240
Concrete Inserts
Length
Part No.
in.
B22-I-3
B22-I-4
B22-I-6
B22-I-8
3”
4”
6”
8”
Wt./C
Lbs.
kg
Lbs.
kN
(76)
72
88
120
152
(32.6)
500
800
1000
1200
(2.22)
(101)
(152)
(203)
Length
Part No.
B22-I-12
B22-I-16
B22-I-20
B22-I-24
B22-I-32
B22-I-36
B22-I-40
B22-I-48
B22-I-60
B22-I-72
B22-I-84
B22-I-96
B22-I-108
B22-I-120
B22-I-144
B22-I-168
B22-I-192
B22-I-216
B22-I-240
Design Load
mm
(39.9)
(54.4)
(68.9)
(3.56)
(4.45)
(5.34)
Wt./C
in.
mm
Lbs.
kg
12”
16”
20”
24”
32”
36”
40”
48”
60”
72”
84”
96”
108”
120”
144”
168”
192”
216”
240”
(305)
224
289
353
420
553
620
686
820
1018
1218
1417
1616
1816
2016
2416
2816
3216
3616
4016
(101.6)
(406)
(508)
(609)
(813)
(914)
(1016)
(1219)
(1524)
(1829)
(2133)
(2438)
(2743)
(3048)
(3657)
(4267)
(4877)
(5486)
(6096)
(131.1)
(160.1)
(190.5)
(250.8)
(281.2)
(311.1)
(371.9)
(461.7)
(552.5)
(642.7)
(733.0)
(823.7)
(914.4)
(1095.9)
(1277.3)
(1458.7)
(1640.2)
(1821.6)
Reference page 213 for general fitting and standard finish specifications
215
Strut Systems
Continuous Concrete Inserts
B32I
Continuous Concrete Insert
4”
(101.6)
• Design Load for B32-I-12 thru B32-I-240
is 2,000 lbs. (8.89 kN) per foot of concrete
MATERIAL: 12 Gauge (2.6)
11/2”
insert length with safety factor of 3 in
(38.1)
3000 psi concrete.
• Loads concentrated within the last 2
inches (50.8 mm) of concrete inserts
27/8”
8” (203.2 mm) and longer should not
(73.0)
exceed 1,000 lbs. (4.45kN).
• Concrete insert should be secured to the
B32-I-3 Thru
forms on 16” (406.4 mm) to 24” (609.6 mm)
11/16”
intervals.
B32-I-8
(17.4)
• B32-I continuous concrete inserts are
25/8”
made from B32 channel. Use channel
13/8”
(66.7)
nuts designed for use in B32 channel.
(34.9)
• B32-I concrete inserts are supplied with
styrofoam fillers. B3332 end caps are
furnished with inserts through 8” (203.2 mm)
long, and B206 end caps are furnished
15/8”
with inserts 12” (304.8 mm) and longer.
13/8” (41.3)
• Material: Plain Steel ASTM A1011
(34.9)
33,000 PSI min. yield or Pre-Galvanized
Styrofoam
Steel ASTM A653SS 33,000 PSI min.
B3332
Filler
yield.
End Cap
• Finish: Plain, DURA GREEN™, Pre-Galv,
B206 End Cap
HDG
B22-I-12
Length
Part No.
in.
B32-I-3
B32-I-4
B32-I-6
B32-I-8
3”
4”
6”
8”
Wt./C
.188 Knockouts For
Nailing Inserts To
Forms
Styrofoam
Filler
THRU B22-I-240
Design Load
Lbs.
kg
Lbs.
kN
(76)
65
80
108
137
(29.5)
500
800
1000
1200
(2.22)
(101)
(152)
(203)
(36.3)
(49.0)
(62.1)
Wt./C
in.
mm
Lbs.
12”
16”
20”
24”
32”
36”
40”
48”
60”
72”
84”
96”
108”
120”
144”
168”
192”
216”
240”
(305)
202
262
316
376
496
556
616
736
915
1095
1274
1453
1633
1813
2173
2533
2893
3253
3613
(406)
(508)
(609)
(813)
(914)
(1016)
(1219)
(1524)
(1829)
(2133)
(2438)
(2743)
(3048)
(3657)
(4267)
(4877)
(5486)
(6096)
kg
(91.6)
(118.8)
(143.3)
(170.5)
(225.0)
(252.2)
(279.4)
(333.8)
(415.0)
(496.7)
(577.9)
(659.0)
(740.7)
(822.3)
(985.6)
(1148.9)
(1312.2)
(1475.5)
(1638.8)
Reference page 213 for general fitting and standard finish specifications.
Strut Systems
3/4”
(19.0)
216
(3.56)
(4.45)
(5.34)
Concrete Inserts
B32-I-12
B32-I-16
B32-I-20
B32-I-24
B32-I-32
B32-I-36
B32-I-40
B32-I-48
B32-I-60
B32-I-72
B32-I-84
B32-I-96
B32-I-108
B32-I-120
B32-I-144
B32-I-168
B32-I-192
B32-I-216
B32-I-240
(41.3)
mm
Length
Part No.
15/8”
Continuous Concrete Inserts
B52I
Continuous Concrete Insert
4”
(101.6)
• Design Load for B52-I-12 thru B52-I-240
MATERIAL: 12 Gauge (2.6)
is 1,500 lbs. (6.67 kN) per foot of concrete
11/2”
(38.1)
insert length with safety factor of 3 in
3000 psi concrete.
3/4”
• Loads concentrated within the last 2
(19.0)
5
2 /16”
inches (50.8 mm) of concrete inserts
(58.7)
8” (203.2 mm) and longer should not
exceed 750 lbs. (3.33kN).
.188 Knockouts For
• Concrete insert should be secured to the
Nailing Inserts To
11/16”
forms on 16” (406.4 mm) to 24” (609.6 mm)
Forms
(17.4)
intervals.
B52-I-3 Thru
• B52-I continuous concrete inserts are
13/16”
B52-I-8
made from B52 channel. Use channel
Styrofoam
(20.6)
nuts designed for use in B52 channel.
29/16”
Filler
• B52-I concrete inserts are supplied with
(65.1)
styrofoam fillers. B3352 end caps are
furnished with inserts through 8” (203.2 mm)
long, and B220 end caps are furnished
15/8”
with inserts 12” (304.8 mm) and longer.
13/16” (41.3)
• Material: Plain Steel ASTM A1011
(20.6)
33,000 PSI min. yield or Pre-Galvanized
B3352
Styrofoam
Steel ASTM A653SS 33,000 PSI min.
End Cap
Filler
yield.
B220 End Cap
• Finish: Plain, DURA GREEN™, Pre-Galv,
B52-I-12 THRU B52-I-240
HDG
Concrete Inserts
Length
Part No.
in.
B52-I-3
B52-I-4
B52-I-6
B52-I-8
3”
4”
6”
8”
Wt./C
Lbs.
kg
Lbs.
kN
(76)
53
63
85
106
(24.0)
400
500
750
1000
(1.78)
(152)
(203)
Length
Part No.
B52-I-12
B52-I-16
B52-I-20
B52-I-24
B52-I-32
B52-I-36
B52-I-40
B52-I-48
B52-I-60
B52-I-72
B52-I-84
B52-I-96
B52-I-108
B52-I-120
B52-I-144
B52-I-168
B52-I-192
B52-I-216
B52-I-240
(41.3)
Design Load
mm
(101)
15/8”
(28.6)
(38.5)
(48.1)
(2.22)
(3.33)
(4.45)
Wt./C
in.
mm
Lbs.
kg
12”
16”
20”
24”
32”
36”
40”
48”
60”
72”
84”
96”
108”
120”
144”
168”
192”
216”
240”
(305)
157
202
237
282
373
419
464
556
692
829
965
1107
1237
1374
1648
1922
2196
2470
2744
(71.2)
(406)
(508)
(609)
(813)
(914)
(1016)
(1219)
(1524)
(1829)
(2133)
(2438)
(2743)
(3048)
(3657)
(4267)
(4877)
(5486)
(6096)
(91.6)
(107.5)
(127.9)
(169.2)
(190.0)
(210.4)
(252.2)
(313.9)
(376.0
(437.7)
(502.1)
(561.1)
(623.2)
(747.5)
(871.8)
(996.1)
(1120.4)
(1244.6)
Reference page 213 for general fitting and standard finish specifications
217
Strut Systems
Spot Inserts
B2500
Spot Insert
N2500
Insert Square Nut
•
•
•
•
• For use in B2500 Spot Insert
• Material: Steel ASTM A36
• Standard finish: ZN
11/4”
Design Load 600 Lbs. (2.67 kN)
Safety Factor of 5
Order N2500 Nuts Separately
Material: Steel ASTM A1011
33,000 PSI min. yield
• Standard finish: ZN
• Wt./C 46 Lbs. (20.8 kg) 2”
11/4”
(31.7)
5/16”
(7.9)
(31.7)
31/4”
Part No.
Thread
Size
(82.5)
N2500-1/4
1/4”-20
(50.8)
N2500-5/16
N2500-3/8
N2500-1/2
N2500-5/8
19/16” N2500-3/4
(65.0)
N2500-7/8
Material:
12 Gauge (2.6)
11/2”
(50.8)
Wt./C
5/16”-18
3/8”-16
1/2-13
5/8”-11
3/4”-10
7/8”-9
B2503
Heavy Duty Spot Insert
B2505 Thru B2508
Spot Insert
• Designed for use where heavy loads are
required in curtain wall applications
• Design Load is 5000 Lbs. (22.2 kN) with a
Safety Factor of 3
• Loading based on two N225 channel nuts
spaced 3” (76.2 mm) on center and a
minimum of 2” (50.8 mm) from the end
of the insert
• Styrofoam end caps prevent concrete
seepage into the channel
• 12” (304.8 mm) long insert is anchored
into the concrete at a depth of
51/2” (139.7 mm)
• Material: 12 Gauge (2.6 mm) thick steel
• Standard finish: ZN
• Wt./C 42 Lbs. (19.0 kg)
• Safety Factor of 5
• To support 10” (250) pipe use B2505
insert with 5/8”-11 Channel Nuts.
• To support up to and including 8” (200)
pipes use B2506, B2507 and
B2508 inserts with the desired
Channel Nuts.
• Standard finish: ZN
Part No.
B22
B32
B42
B52
Lbs.
kg
13
13
12
12
11
10
9
(5.9)
(5.9)
(5.4)
(5.4)
(5.0)
(4.5)
(4.1)
Channel
Size
Channel End Cap
Style
Part No.
B2505
B2506
B2507
B2508
Thread Size
B3322
B3332
B3342
B3352
End Caps
25/8”
(66.7)
51/16”
(128.6)
Design Load
Lbs.
kN
1200
1000
1000
1000
(5.34)
Maximum
Pipe Size
10”
8”
8”
8”
(4.45)
(4.45)
(4.45)
(250)
(200)
(200)
(200)
Wt./C
Lbs.
kg
96
88
77
69
(43.5)
(39.9)
(34.9)
(31.3)
Concrete Inserts
B2501
Light Duty Spot Insert
51/2”
(139.7)
15/8”
2”
5/32” (4.0)
(41.3)
(50.8)
15/8”
DIA. NAIL
HOLES
(41.3)
• Safety Factor of 2
• The concrete attachment problem solver for
light duty applications.
• Fast and easy applications.
• No concrete leakage problems.
• One piece unitized construction.
• Color coded cap on thread for rod size
identification and to prevent concrete seepage.
(1/4”-Yellow, 3/8”-Red, 1/2”-Blue)
A
H
8”
11/4”
(203.2)
(31.7)
Design Load
12”
(304.8)
Styrofoam End
Caps
Part No.
& Size
B2501-1/4
B2501-3/8
B2501-1/2
Height A
Height H
In.
In.
mm
mm
27/16” (61.9)
31/16” (77.8)
7/8” (22.2)
17/8” (47.6)
41/8” (104.8)
17/8” (47.6)
Reference page 213 for general fitting and standard finish specifications.
Strut Systems
218
Design Load
Wt./C
Lbs.
kN
Lbs.
kN
250
610
880
(1.11)
16
22
26
(7.2)
(2.71)
(3.91)
(9.9)
(11.7)
Insert Accessories
B205, B206, B220
X Type End Caps
B3322, B3332, B3342, B3352
Y Type End Caps
• UL listed for raceway use only
• Material: 12 Gauge (2.6)
• Standard finish: ZN
• UL listed for raceway use only
• Material: 14 Gauge (1.9)
• Standard finish: ZN
5/8” (9.5)
DIA.
A
25/8”
(66.7)
A
1”
113/16”
(25.4)
(46.0)
Part No.
B205
B206
B220
Use
With
B22
B32
B52
A
In.
Wt./C
mm
Lbs.
121/32” (42.0)
113/32” (35.7)
kg
10 (4.5)
8 (3.6)
4 (1.8)
27/32” (21.4)
13/4”
B380
Joint Splice Plate
Part No.
Use
With
In.
A
mm
Lbs.
Wt./C
kg
B3322
B3332
B3342
B3352
B22
B32
B42
B52
1.270
1.000
.645
.460
(32.2)
15
15
15
15
(6.8)
(25.4)
(16.4)
(11.7)
(6.8)
(6.8)
(6.8)
B22IFS-B52IFS
Styrofoam Filler Strip
(44.1)
• Used at splice points to prevent
concrete seepage in long
A
continuous runs of concrete
inserts.
1/16”
• Material: 18 Gauge (1.2)
(1.6)
• Standard finish: GALV
29/32”
(23.0)
15/8”
(41.3)
B
A
Concrete Inserts
Part No.
B380-22
B380-32
B380-42
B380-52
Use
With
B22
B32
B42
B52
A
In.
Wt./C
mm
15/8” (41.3)
13/8” (34.9)
1” (25.4)
13/16” (20.6)
Lbs.
11
10
9
7
kg
(5.0)
(4.5)
(4.1)
(3.2)
A
Part No.
B22-IFS
B32-IFS
B52-IFS
Ft.
4’
4’
4’
B
mm
In.
mm
(1219)
17/32” (309)
(1219)
1” (254)
21/32” (167)
(1219)
Wt./C
Lbs.
kg
10
9
7
(4.5)
(4.1)
(3.2)
Pipe Sleeve Fasteners
• Allows for rigid attachment
of pipe sleeves to wall and floor
forms for concrete pouring.
• Accommodates Schedule 40,
Schedule 80, or 5/16" (8) and
smaller wall thickness.
• Simply installed with a hammer.
Part No.
BD40
Sleeve
Diameter
All Dia.
BD40
BE-5-8 & BE-9-12
Wall
Thickness
5/16”
& under
BE-5-8
6”
Schedule 80 pipe
BE-9-12
9” - 14”
Schedule 80 pipe
Reference page 213 for general fitting and standard finish specifications
219
Strut Systems
Anchors
Wedge Anchors
Catalog
Number
Thread
Size
AWA-37-225
AWA-37-275
AWA-37-300
AWA-37-350
AWA-37-375
AWA-37-500
AWA-50-275
AWA-50-375
AWA-50-450
AWA-50-550
AWA-50-700
3/8"-16
3/8"
3/8"-16
3/8"
Thread
Length
Size
in.
21/4"
x
x 23/4"
3/8" x 3"
3/8" x 31/2"
3/8" x 33/4"
3/8" x 5"
1/2" x 23/4"
1/2" x 33/4"
1/2" x 41/2"
1/2" x 51/2"
1/2" x 7"
3/8"-16
3/8"-16
3/8"-16
3/8"-16
1/2"-13
1/2"-13
1/2"-13
1/2"-13
1/2"-13
Drill/Hole
Size
mm
in.
mm
(9 x 57)
(9 x 70)
(9 x 76)
(9 x 89)
(9 x 95)
(9 x 127)
(13 x 70)
(13 x 95)
(13 x 114)
(13 x 140)
(13 x 178)
11/4"
(32)
(41)
(47)
(60)
(66)
(98)
(35)
(60)
(79)
(105)
(143)
15/8"
17/8"
23/8"
25/8"
37/8"
13/8"
23/8"
31/8"
41/8"
55/8"
in. mm
Load Cap.
Tension*
lbs.
Load Cap.
Shear*
kN
lbs.
kN
3/8” (9)
760 (3.38)
940 (4.18)
1/2” (13)
1390 (6.18)
1700 (7.56)
Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.
Hollow Base Drop-In Anchors
Catalog
Number
Rod
Size
Overall
Length
in.
mm
in.
mm
in.
mm
ADH-25
ADH-37
ADH-50
9323
9343
9353
1/4”-20
7/8”
(22)
5/8”
(16)
3/8”
(9)
3/8”-16
15/16”
13/4”
----
(33)
15/16” (24)
5/8” (16)
(44)
11/4” (32)
-------
3/4” (19)
1/2”-13
1/4”
3/8”
1/2”
Sleeve
Length
----
Drill/Hole
Diameter
----
Load Cap.
Tension*
lbs.
kN
285 (1.27)
520 (2.31)
1005 (4.47)
-------
----
Load Cap.
Shear*
lbs.
kN
300 (1.33)
640 (2.84)
1005 (44.70)
-------
Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.
RAPID ROD™ Hangers for Concrete
Rod
Shank Size
Drill/Hole
Size
& Length
Size
in.
mm
Load Cap.
Tension*
Load Cap.
Shear*
Lbs.
kN
in.
mm
Lbs.
kN
ARC-25-125
1/4”-20
1/4”
x 11/4” (6 x 32)
1/4”
(6)
485
(2.16)
610
(2.71)
ARC-37-150
3/8”-16
1/4”
x
11/2” (6 x 38)
1/4”
(6)
650
(2.89)
660
(2.93)
ARC-50-275
1/2”-13
3/8”
x
23/4” (9 x 70)
1/4”
(6)
1510 (6.71)
1580 (7.03)
Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.
RAPID ROD™ Hangers for Steel
Catalog
Number
Rod
Size
Shank Size
& Length
in.
Load Cap.
Tension* In 12 Ga.
mm
Lbs.
(6 x 25)
390
(1.75)
1260 (5.60)
x 1” * (6 x 25)
512
(2.28)
1260 (5.60)
11/2” (6 x 38)
390
(1.75)
1260 (5.60)
x 11/2” (6 x 38)
512
(2.28)
1260 (5.60)
390
(1.75)
1260 (5.60)
ARS-25-100
1/4”-20
1/4”
x 1”
ARS-37-100HN
3/8”-16
1/4”
ARS-37-150
3/8”-16
1/4”
x
ARS-37-150HN
3/8”-16
1/4”
ARS-37-200
3/8”-16
1/4”
x 2”
(6 x 51)
kN
Load Cap.
Tension* In 1/4”
Lbs.
kN
Note: Loads shown for ASTM A36 beams and ASTM A572 steel purlins include a safety factor of 4.
For UL and FM listings, steel rapid rod must be installed with a retaining nut.
Reference page 213 for general fitting and standard finish specifications.
Strut Systems
220
Concrete Inserts
Catalog
Number
Anchors
Plastic Screw Anchors
• Kits contain 100 anchors, 100 screws, and 1 concrete drill bit
Catalog
Screw
Number
Size
Load Cap.
Tension*
Lbs.
#8 x 1”
#10 x 1”
#12 x 1”
APC-8K
APC-10K
APC-12K
Load Cap.
Shear*
kN
Lbs.
110 (0.49)
140 (0.62)
140 (0.62)
kN
70 (0.31)
90 (0.40)
90 (0.40)
Note: Based on concrete compression strength of 4,000 psi using
applied safety factor of 4.
Wood-Knocker™† Anchors
Catalog
Number
Rod
Size
ACPW-25
ACPW-37
ACPW-50
ACPW-62
ACPW-75
1/4”-20
Color
3/8”-16
1/2”-13
5/8”-11
3/4”-10
Brown
Green
Yellow
Red
Purple
Insert Thread
Length
Overall
Length
Load Cap.
Tension*
Load Cap.
Shear*
in.
mm
in.
mm
lbs.
kN
3/8”
(9)
(47)
(16)
930
1200
1200
1160
1160
(4.13)
5/8”
17/8”
17/8”
17/8”
17/8”
17/8”
11/16” (17)
15/16” (24)
11/8” (28)
(47)
(47)
(47)
(47)
lbs.
kN
370 (1.64)
1330 (5.91)
1840 (8.18)
2800 (12.45)
2800 (12.45)
(5.33)
(5.33)
(5.16)
(5.16)
Notes: Based on normal weight concrete with minimum compression strength of 3,000 psi.
Allowable load capacities are calculated using applied safety factor of 4.
Minimum embedment is 2” (51mm).
† Wood-Knocker™ is a trademark of Powers® Fasteners
Concrete Inserts
Bang-It™† Anchors
Catalog
Number
Rod
Size
ACPD-25
ACPD-37
ACPD-50
ACPD-62
ACPD-75
ACPD-87
1/4”-20
3/8”-16
1/2”-13
5/8”-11
3/4”-10
7/8”-9
Color
Brown
Green
Yellow
Red
Purple
Black
Insert Thread Upper Deck
Lower Deck Upper Deck Lower Deck
Length
Tension Load* Tension Load* Shear Load* Shear Load*
in.
mm
lbs.
kN
lbs.
kN
lbs.
kN
lbs.
kN
3/8”
(9)
(4.94)
625
837
837
837
837
837
(2.78)
625
837
837
837
837
837
(2.78)
(16)
830
830
830
990
990
990
(3.69)
5/8”
1112
1435
1775
2200
2200
2200
11/16” (17)
15/16” (24)
11/8” (28)
15/16” (33)
(6.38)
(7.89)
(9.78)
(9.78)
(9.78)
(3.69)
(3.69)
(4.40)
(4.40)
(4.40)
(3.72)
(3.72)
(3.72)
(3.72)
(3.72)
(3.72)
(3.72)
(3.72)
(3.72)
(3.72)
Notes: Based on normal weight concrete with minimum compression strength of 3,000 psi.
Allowable load capacities are calculated using applied safety factor of 4.
Minimum insert spacing of 12” (305mm), minimun end spacing of 12” (305mm).
Minimum embedment is 2” (51mm).
Length of sleeve is 33/8” (86mm.
† Bang-It™ is a trademark of Powers® Fasteners
Reference page 213 for general fitting and standard finish specifications
221
Strut Systems
Anchors
1/4”
Concrete Screws
Catalog
Number
Rod
Size
in.
ACS-125H
ACS-175H
ACS-225H
ACS-275H
ACS-325H
Drill/Hole
Size
Load Cap.
Shear*
in.
mm
lbs.
kN
lbs.
kN
1/4”
11/4” (6 x 32)
3/16”
(5)
(6 x 44)
3/16”
(5)
(6 x 57)
3/16”
(5)
(6 x 70)
3/16”
(5)
(6 x 82)
3/16”
(5)
205
205
205
205
205
(0.91)
13/4”
21/4”
23/4”
31/4”
265
265
265
265
265
(1.18)
1/4”
x
x
1/4” x
1/4” x
1/4” x
mm
Load Cap.
Tension*
(1.18)
(1.18)
(1.18)
(1.18)
(0.91)
(0.91)
(0.91)
(0.91)
Note: Based on 1” (25mm) embedment with concrete compression strength of 4,000 psi using applied safety factor of 4.
Consult factory for loading of other embedment depths.
Self-Tapping Machine Screw Anchor
Catalog
Number
ATM-37
Rod
Size
Thread
Depth
3/8”-16
Drill/Hole
Size
Load Cap.
Tension*
in.
mm
in.
mm
Lbs.
11/16”
(17)
1/2”
(13)
540 (2.40)
Load Cap.
Shear*
kN
Lbs.
kN
825 (3.67)
Note: Based on concrete compression strength of 4,000 psi in uncracked concrete using applied safety factor of 4.
Minimum concrete thickness 4” (101mm) with minimum embedment of 15/8” (41mm)
Wall Screws
Catalog
Number
Head
Type
Thread
Depth
in.
Minimum
Embedment
mm
Load Cap.
Tension*
Load Cap.
Shear*
Lbs.
in.
mm
Lbs.
kN
kN
Combo
3/16”
x 11/4” (5 x 32)
3/4”
(19)
90
(0.40)
260 (1.15)
AWS-OH
Oval
3/16”
x
11/4” (5 x 32)
3/4”
(19)
90
(0.40)
260 (1.15)
AWS-PH
Pan
3/16”
x 11/4” (5 x 32)
3/4”
(19)
90
(0.40)
260 (1.15)
AWS-CH
Sleeve Type Expansion Anchors
Catalog
Number
Anchor Size
& Length
in.
ASA-37-187HN
ASA-37-300HN
ASA-37-400HN
ASA-50-225HN
ASA-50-300HN
ASA-50-400HN
ASA-50-525HN
ASA-50-600HN
3/8”
x
3/8”
mm
17/8” (9 x 47)
x 3” (9 x 76)
3/8” x 4” (9 x 101)
1/2” x 21/4” (13 x 57)
1/2” x 3” (13 x 76)
1/2” x 4” (13 x 101)
1/2” x 51/4” (13 x 133)
1/2” x 6” (13 x 152)
Thread
Length
in.
mm
Drill/Hole
Minimum
Diameter Embedment
in.
Load Cap.
Tension*
Load Cap.
Shear*
mm
in.
mm
lbs.
kN
lbs.
kN
15/8” (41)
3/8”
(9)
15/8”
(41)
3/8”
(9)
(41)
(41)
3/8”
(9)
(57)
1/2” (13)
(57)
1/2” (13)
(57)
1/2” (13)
(57)
1/2” (13)
(57)
1/2” (13)
15/8”
15/8”
21/4”
21/4”
21/4”
21/4”
21/4”
610
610
610
1055
1055
1055
1055
1055
(2.71)
(41)
670
670
670
1255
1255
1255
1255
1255
(2.98)
15/8”
15/8”
21/4”
21/4”
21/4”
21/4”
21/4”
(41)
(57)
(57)
(57)
(57)
(57)
(2.98)
(2.98)
(5.58)
(5.58)
(5.58)
(5.58)
(5.58)
Note: Based on concrete compression strength of 4,000 psi using applied safety factor of 4.
Reference page 213 for general fitting and standard finish specifications.
Strut Systems
222
(2.71)
(2.71)
(4.69)
(4.69)
(4.69)
(4.69)
(4.69)
Concrete Inserts
Note: Based on concrete compression strength of 4,000 psi. Allowable load capacities are calculated using an
applied safety factor of 4.