I00022039
4.125
DRILL 13/32 HOLE
4 PL
1.000
3.250
3/4 SPAN
"LONG" SIDE
1/4 SPAN
"SHORT" SIDE
3.250
1/4
SPAN
3/4
SPAN
SUPPORT
SPAN
INSTALLED VIEW
(BONDING JUMPER AND SUPPORTS
NOT SHOWN FOR CLARITY)
STEP 1.
MARK AND DRILL HOLES
GAP
3/4 SPAN TRAY
APPLY 8" BEADS OF GREASE
3 PER SIDE
TORQUE ELASTIC STOP NUTS UNTIL SNUG
BACK OFF 1/4 TURN
(4 PLACES)
SERRATED FLANGE HEX NUTS
TORQUE: 19 FT-LBS
(2 PLACES)
8"
STEP 2.
GREASE SIDERAIL
(ONLY NEED TO
GREASE THE 3/4
SPAN TRAY)
STEP 3.
1/4 SPAN TRAY
POSITION THE SPLICE PLATE SO THAT THE SCREWS ARE
AGAINST THE INSIDE OF THE SLOWTS AS SHOWN
A: INSTALL SPLICE PLATE AND HARDWARE.
B: POSITION SPLICE ON 1/4 SPAN TRAY AS SHOWN AND TORQUE HARDWARE
C: SET GAP ACCORDING TO CHART 2 SHOWN ON PAGE 2
D: TORQUE 3/4 SPAN TRAY HARDWARE AS SHOWN
THIS DRAWING AND/OR THE TECHNICAL INFORMATION CONTAINED HEREON IS THE PROPERTY OF COOPER B-LINE, INC. ("B-LINE"), AND IS ISSUED IN CONFIDENCE FOR B-LINE ENGINEERING PURPOSES ONLY AND MAY NOT BE REPRODUCED OR USED FOR ANY PURPOSE WHATSOEVER
WITHOUT THE EXPRESS WRITTEN PERMISSION OF B-LINE TO THE USER. THIS DRAWING AND/OR TECHNICAL INFORMATION IS THE PROPERTY OF B-LINE AND IS LOANED FOR MUTUAL ASSISTANCE, TO BE RETURNED WHEN ITS' INTENDED PURPOSE HAS BEEN SERVED.
INSTRUCTION SHEET CT-15 PAGE 1 OF 2
TITLE:
509 W. Monroe Street
Highland, IL 62249
Phone (618) 654-2184
FAX (618) 654-5499
www.cooperbline.com
STEEL HEAVY DUTY
EXPANSION SPLICE PLATE
9G-6016 9SS6-6016
9G-6017 9SS6-6017
EQUIPMENT FURNISHED HAS BEEN FABRICATED IN ACCORDANCE WITH THIS DRAWING.
SUBMITTAL NO:
REFERENCE DWG(S):
I00022039
DRAWN BY:
BMT
DATE:
MODEL SOURCE FILE:
00022039
REV:
SHEET:
REV.
6-25-12
1 OF 1
STEP 4:
INSTALL BONDING JUMPERS
(2 REQUIRED PER SIDE)
I00022039
DRILL HOLE THROUGH SIDE RAIL
INSTALL HARDWARE
TORQUE: 19 FT-LBS
SPLICE BONDING
JUMPERS TOGETHER
DENOTES SUPPORT LOCATIONS
STANDARD SPLICE PLATES
X
-
-
X
X
-
X
HEAVY DUTY
EXPANSION
SPLICE PLATE
X DENOTES HOLD-DOWN CLAMP
(ANCHOR) AT SUPPORTS
- DENOTES EXPANSION GUIDE
CLAMPS AT SUPPORT
X
-
HEAVY DUTY
EXPANSION
SPLICE PLATE
X
SUPPORT LOCATIONS
HEAVY DUTY EXPANSION SPLICE PLATES ALLOW THE SUPPORTS TO BE AT THE
QUARTER POINT OF THE SPAN (SEE BELOW GRAPHIC) VERSUS THE NORMAL
RECOMMENDATION OF SUPPORTS BEING WITHIN 2 FT (600 MM) OF EACH
DIRECTION OF THE EXPANSION SPLICE PLATE
MAXIMUM SPACING BETWEEN EXPANSION JOINTS FOR 1" MOVEMENT
TEMP DIFFERENTIAL
STEEL
STAINLESS STEEL 304
STAINLESS STEEL 316
F
C
FEET
M
FEET
M
FEET
M
25
13.9
512
156.0
347
105.7
379
115.5
50
27.8
256
78.0
174
53.0
189
57.6
75
41.7
171
52.1
116
35.4
126
38.4
100
55.6
128
39.0
87
26.5
95
29.0
125
69.4
102
31.1
69
21.0
76
23.2
150
83.3
85
25.9
58
17.7
63
19.2
175
97.2
73
22.2
50
15.2
54
16.4
NOTE: EVERY PAIR OF EXPANSION SPLICE PLATES REQUIRES FOUR BONDING JUMPERS FOR GROUNDING CONTINUITY.
THIS DRAWING AND/OR THE TECHNICAL INFORMATION CONTAINED HEREON IS THE PROPERTY OF COOPER B-LINE, INC. ("B-LINE"), AND IS ISSUED IN CONFIDENCE FOR B-LINE ENGINEERING PURPOSES ONLY AND MAY NOT BE REPRODUCED OR USED FOR ANY PURPOSE WHATSOEVER
WITHOUT THE EXPRESS WRITTEN PERMISSION OF B-LINE TO THE USER. THIS DRAWING AND/OR TECHNICAL INFORMATION IS THE PROPERTY OF B-LINE AND IS LOANED FOR MUTUAL ASSISTANCE, TO BE RETURNED WHEN ITS' INTENDED PURPOSE HAS BEEN SERVED.
INSTRUCTION SHEET CT-15 PG 2 OF 2
TITLE:
509 W. Monroe Street
Highland, IL 62249
Phone (618) 654-2184
FAX (618) 654-5499
www.cooperbline.com
STEEL HEAVY DUTY
EXPANSION SPLICE PLATE
9G-6016 9SS6-6016
9G-6017 9SS6-6017
EQUIPMENT FURNISHED HAS BEEN FABRICATED IN ACCORDANCE WITH THIS DRAWING.
SUBMITTAL NO:
REFERENCE DWG(S):
I00022039
DRAWN BY:
BMT
DATE:
MODEL SOURCE FILE:
REV:
SHEET:
REV.
6-25-12
1 OF 1