Science Building
B104
THIS ROOM IS EQUIPPED WITH:
COMPUTER
PC
Laptop Connection
Wireless Presenter
VIDEO
Video Projector
VCR/DVD Player
AUDIO
Wall Speakers
Projector Controlled
Audio System
VCR/DVD
1

To use the projector:
1. Make sure both the projector and the needed audio/video device (Computer, VCR, DVD, etc.) are
2. Use the corresponding INPUT button on the projector’s remote to activate the audio/video input line for the device.
Computers, laptops, and document cameras are activated by using the
COMPUTER button on the projector remote. VCR and DVD players are activated by pressing the VIDEO button on the projector remote.
This room may be equi pped with a VGA Switch that requires additional input selection to display the device through the projector. A detailed explanation of how to operate each device is given in the following sections of the manual.
Input Buttons
INPUT CONFIGURATION:
Computer 1 - PC/Laptop
Video - VCR/DVD
Projector Remote
2

All audio in the Projector Controlled Audio System is adjusted directly through the volume button on the projector’s remote. Additionally, the remote‘s AV Mute button can be used to silence the audio and simultaneously black the screen.
AV Mute Button
Projector Remote
Volume Button
Windows System
Volume
Note: When the computer is used for audio, sound is also controlled via the Windows
System Volume. This may also need to be adjusted to reach the desired volume.
3

To use the VCR/DVD Combo:
1.) Turn on the projector by pressing the POWER button on the projector remote. (See page 2.)
2.) Use the VIDEO input button on the projector remote to select the combo player as the audio/video source.
3.) Turn on the combo player by pressing the POWER button and insert your media to begin playing.
4.) Use the VCR/DVD button on the combo player to
select between playing a VHS Tape or a DVD.
4

To use the computer:
1.) LOGON to the computer using your UWSP username and
password.
2.) To display the computer’s screen on the projector, turn the projector on using the POWER button on the remote. Then press the corresponding input button on the projector remote to choose the
PC/Laptop as the video source (see the “PROJECTOR” page). The computer will display on the projector as long as no other devices are
active.
Unlocking a computer:
If the PC’s screen indicates that it has been locked by another user, you can unlock the system by restarting it. To restart a locked computer:
1.) Press and hold the POWER button on the computer until it shuts down (typically, you will need to hold the button for 5 to 10 seconds before the sequence will begin).
2.) Press the POWER button again to restart the PC. When the login screen appears, enter your UWSP username and password.
NOTE: Please remember to logoff the computer when finished.
After 60 minutes of inactivity, classroom computers will automatically lock, preventing subsequent users from logging on.
5

This room is equi pped with an autoswitch that detects when a device is connected to the laptop VGA cable and routes the audio and video signals accordingly.
To connect a laptop computer:
1.) Plug the VGA cable into the VGA port on your laptop and, if audio is desired, plug the 1/8” stereo cable into your laptop’s headphone jack.
If your laptop does not have a VGA port, contact Tech Support for further assistance. Also, some laptops require proper configuration to utilize an external display. To configure your laptop accordingly, please refer to the instructions provided by your manufacturer.
2.) Once the autoswitch has detected the laptop, the projector should display the laptop’s video feed on the screen. Disconnecting the laptop VGA cable will restore the PC’s video feed to the projector.
If using sound, please note that the audio signal follows the video feed.
Connecting to the Internet:
Many classrooms are equi pped with an Ethernet cable allowing for wired internet access. It is advisable to use a wired connection whenever possible.
Wireless internet connections are also available in most classrooms. For instructions on configuring your laptop, contact Help Desk at x4375 or visit www.uwsp.edu/IT/Network/Wireless .
6
6
VGA Cable

B104
For issues related to technical services, please consult the technical support information found on the front cover.
At the end of class:
At the end of class:
SEE FRONT
During the hours of 7 AM - 3:30 PM, issues related to building maintenance may be directed to Facility Services. During off-hours, maintenance emergencies may be reported to Protective Services.
x 4219
FACILITY SERVICES
For issues related to building or campus security, please contact
Campus Protective Services.
x 3456
CAMPUS PROTECTIVE
SERVICES
9-911
SPPD/SPFD
NOTE: There will be 7-12 seconds of silence before the phone rings. Please do not hang up.
EXIT
EXIT
EXIT
EXIT
Lobby
EXIT EXIT
FIRST
FLOOR EXIT
B104
EXIT
EXIT
EXIT