Video Encoder EI3 Extender Board
Manual
an EZ-Extender® product
Revision 1.1, November 2012
Part Number
82-000252-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
a
Copyright Information
© 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, Blackfin, CrossCore, EngineerZone, EZ-Board,
EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of
Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.
Regulatory Compliance
The Video Encoder EI3 Extender Board is designed to be used solely in a
laboratory environment. The board is not intended for use as a consumer
end product or as a portion of a consumer end product. The board is an
open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity.
This board should not be used in or near any medical equipment or RF
devices.
The Video Encoder EI3 Extender Board has been certified to comply with
the essential requirements of the European EMC directive 2004/108/EC
and therefore carries the “CE” mark.
The Video Encoder EI3 Extender Board has been appended to Analog
Devices, Inc. EMC Technical File (EMC TF) referenced DSPTOOLS1,
issue 2 dated June 4, 2008 and was declared CE compliant by an
appointed Notified Body (No.0673) as listed below.
Notified Body Statement of Compliance: Z600ANA2.045 dated September 3, 2012.
Issued by: Technology International (Europe) Limited
56 Shrivenham Hundred Business Park
Shrivenham, Swindon, SN6 8TY, UK
The extender board contains ESD (electrostatic discharge) sensitive devices.
Electrostatic charges readily accumulate on the human body and equipment
and can discharge without detection. Permanent damage may occur on
devices subjected to high-energy discharges. Proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
Store unused extender boards in the protective shipping package.
CONTENTS
PREFACE
Product Overview .........................................................................
ix
Purpose of This Manual .................................................................
x
Intended Audience ........................................................................
xi
Manual Contents ..........................................................................
xi
What’s New in This Manual ......................................................... xii
Technical Support ........................................................................ xii
Supported Products ..................................................................... xiii
Product Information ................................................................... xiii
Analog Devices Web Site ....................................................... xiii
EngineerZone ......................................................................... xiv
Related Documents ....................................................................... xv
Notation Conventions ................................................................... xv
USING VIDEO ENCODER EI3 EXTENDER BOARD
Package Contents .......................................................................... 1-2
Video Encoder EI3 Extender Board Installation ............................. 1-2
High Performance HDMI Transmitter (ADV7511) ........................ 1-3
Multi-Format Video Encoder (ADV7431) ..................................... 1-4
Video Encoder EI3 Extender Board Manual
v
Contents
Expansion Interface III ................................................................. 1-5
Example Programs ........................................................................ 1-6
Board Design Database ................................................................. 1-7
VIDEO ENCODER EI3 EXTENDER BOARD HARDWARE
REFERENCE
System Architecture ...................................................................... 2-2
Software-Controlled Switches (SoftConfig) ................................... 2-3
Overview of SoftConfig ........................................................... 2-3
Programming SoftConfig ........................................................ 2-7
Video Encoder Mode Select ................................................... 2-10
ADV7511_INT_GPIOx Signal ............................................. 2-10
27MHZ_CLK_EN Signal ..................................................... 2-10
74MHZ_CLK_EN Signal ..................................................... 2-10
SPORT_ENABLE Signal ...................................................... 2-10
Connectors ................................................................................. 2-11
Expansion III (EI3) Connectors (J4) ...................................... 2-12
S-Video Connector (J2) ........................................................ 2-12
Component Connector (J14) ................................................ 2-13
HDMI Connector (J5) .......................................................... 2-13
Composite Connector (J6) .................................................... 2-14
Power Connector (P1) ........................................................... 2-14
LEDs ......................................................................................... 2-15
HDMI Detect LED (LED1) .................................................. 2-15
Power LED (LED2) .............................................................. 2-15
vi
Video Encoder EI3 Extender Board Manual
Contents
VIDEO ENCODER EI3 EXTENDER BOARD BILL OF
MATERIALS
VIDEO ENCODER EI3 EXTENDER BOARD SCHEMATIC
INDEX
Video Encoder EI3 Extender Board Manual
vii
Contents
viii
Video Encoder EI3 Extender Board Manual
PREFACE
Thank you for purchasing the Video Encoder EI3 Extender Board, an
EZ-Extender® product for EZ-KIT Lite®/EZ-Board® evaluation systems
with the expansion interface 3 (EI3).
The EZ-KIT Lite/EZ-Board and Video Encoder EI3 Extender Board are
designed to be used in conjunction with the CrossCore® Embedded
Studio (CCES) development environment.
To learn more about Analog Devices development software, go to
http://www.analog.com/processors/tools.
Product Overview
The Video Encoder EI3 Extender Board is a separately sold daughter
board that plugs onto the expansion interface 3 (EI3) of an EZ-KIT
Lite/EZ-Board evaluation system. The extender board aids the design and
prototyping phases of embedded processor-targeted applications.
The board extends the capabilities of the evaluation system by providing a
connection between the parallel peripheral interface (PPI) of the processor
and the ADV7511 and ADV7341 video encoders. The SPORT is used for
transmitting audio data. The two-wire interface (TWI) port of the processor is used to communicate to the video encoders and SoftConfig on the
extender.
Video Encoder EI3 Extender Board Manual
ix 
Purpose of This Manual
The following is a list of the Video Encoder EI3 Extender Board
interfaces.
• Video interface
• ADV7511 — 225 MHz, high performance HDMI transmitter with ARC
•
ADV7341— multi-format video encoder, six 12-bit noiseshaped video DACs
• Video connectors
• One HDMI
• One SVIDEO
• One component
• One composite
• No power supply required: derives power from the EZ-KIT
Lite/EZ-Board
• CE certified
• Traditional mechanical switches and jumpers for changing the
board’s factory setup have been removed in favor of I2C-controlled
software switches.
Purpose of This Manual
The Video Encoder EI3 Extender Board Manual provides instructions for
installing the product hardware (board). The text describes operation and
configuration of the board components and provides guidelines for running your own code on the Video Encoder EI3 Extender Board. Finally, a
schematic and a bill of materials are provided for reference.
x
Video Encoder EI3 Extender Board Manual
Preface
Intended Audience
The primary audience for this manual is a programmer who is familiar
with Analog Devices processors. This manual assumes that the audience
has a working knowledge of the appropriate processor architecture,
instruction set, and C/C++ programming languages.
Programmers who are unfamiliar with Analog Devices processors can use
this manual, but should supplement it with other texts that describe your
target architecture and hardware development tools.
Programmers who are unfamiliar with the CrossCore Embedded Studio
programming environment or the mating evaluation board, should refer
to the CCES online help.
Manual Contents
The manual consists of:
• Chapter 1, “Using Video Encoder EI3 Extender Board” on
page 1-1
Provides basic board information.
• Chapter 2, “Video Encoder EI3 Extender Board Hardware Reference” on page 2-1
Provides information about the product’s hardware components.
• Appendix A, “Video Encoder EI3 Extender Board Bill Of Materials” on page A-1
Provides a list of hardware components used to manufacture the
extender board.
• Appendix B, “Video Encoder EI3 Extender Board Schematic” on
page B-1
Provides all circuits on the extender board.
Video Encoder EI3 Extender Board Manual
xi
What’s New in This Manual
What’s New in This Manual
This is the second revision of the Video Encoder EI3 Extender Board Manual. It includes the updated regulatory compliance section and minor
modifications based on the errata report against the first revision.
Technical Support
You can reach Analog Devices processors and DSP technical support in
the following ways:
• Post your questions in the processors and DSP support community
at EngineerZone®:
http://ez.analog.com/community/dsp
• Submit your questions to technical support directly at:
http://www.analog.com/support
• E-mail your questions about processors, DSPs, and tools development software from CrossCore Embedded Studio or
VisualDSP++®:
Choose Help > Email Support. This creates an e-mail to
processor.tools.support@analog.com and automatically attaches
your CrossCore Embedded Studio or VisualDSP++ version information and license.dat file.
• E-mail your questions about processors and processor applications
to: 
processor.support@analog.com or
processor.china@analog.com (Greater China support)
• In the USA only, call 1-800-ANALOGD (1-800-262-5643)
xii
Video Encoder EI3 Extender Board Manual
Preface
• Contact your Analog Devices sales office or authorized distributor.
Locate one at:
www.analog.com/adi-sales
• Send questions by mail to:
Processors and DSP Technical Support
Analog Devices, Inc.
Three Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Products
This extender board supports EZ-KIT Lite/EZ-Board evaluation systems
with the expansion interface 3.
Product Information
Product information can be obtained from the Analog Devices Web site
and the CCES online help system.
Analog Devices Web Site
The Analog Devices Web site, www.analog.com, provides information
about a broad range of products—analog integrated circuits, amplifiers,
converters, and digital signal processors.
To access a complete technical library for each processor family, go to
http://www.analog.com/processors/technical_library. The manuals
selection opens a list of current manuals related to the product as well as a
link to the previous revisions of the manuals. When locating your manual
Video Encoder EI3 Extender Board Manual
xiii
Product Information
title, note a possible errata check mark next to the title that leads to the
current correction report against the manual.
Also note, myAnalog.com is a free feature of the Analog Devices Web site
that allows customization of a Web page to display only the latest information about products you are interested in. You can choose to receive
weekly e-mail notifications containing updates to the Web pages that meet
your interests, including documentation errata against all manuals.
myAnalog.com provides access to books, application notes, data sheets,
code examples, and more.
Visit myAnalog.com (found on the Analog Devices home page) to sign up.
If you are a registered user, just log on. Your user name is your e-mail
address.
EngineerZone
EngineerZone is a technical support forum from Analog Devices. It allows
you direct access to ADI technical support engineers. You can search
FAQs and technical information to get quick answers to your embedded
processing and DSP design questions.
Use EngineerZone to connect with other DSP developers who face similar
design challenges. You can also use this open forum to share knowledge
and collaborate with the ADI support team and your peers. Visit
http://ez.analog.com to sign up.
xiv
Video Encoder EI3 Extender Board Manual
Preface
Related Documents
For additional information about the product, refer to the following
publications.
Table 1. Related Processor Publications
Title
Description
Processor Data Sheet
General functional description, pinout, and timing
of the processor
Processor Hardware Reference
Description of the internal processor architecture and
all register functions
Blackfin® Processor Programming Reference Description of all allowed processor assembly
instructions
Notation Conventions
Text conventions used in this manual are identified and described as follows. Additional conventions, which apply only to specific chapters, may
appear throughout this document.
Example
Description
Close command 
(File menu)
Titles in reference sections indicate the location of an item within the
CCES environment’s menu system (for example, the Close command
appears on the File menu).
{this | that}
Alternative required items in syntax descriptions appear within curly
brackets and separated by vertical bars; read the example as this or
that. One or the other is required.
[this | that]
Optional items in syntax descriptions appear within brackets and separated by vertical bars; read the example as an optional this or that.
[this,…]
Optional item lists in syntax descriptions appear within brackets delimited by commas and terminated with an ellipse; read the example as an
optional comma-separated list of this.
Video Encoder EI3 Extender Board Manual
xv 
Notation Conventions
Example
Description
.SECTION
Commands, directives, keywords, and feature names are in text with
letter gothic font.
filename
Non-keyword placeholders appear in text with italic style format.
xvi

Note: For correct operation, ...
A Note provides supplementary information on a related topic. In the
online version of this book, the word Note appears instead of this
symbol.

Caution: Incorrect device operation may result if ...
Caution: Device damage may result if ... 
A Caution identifies conditions or inappropriate usage of the product
that could lead to undesirable results or product damage. In the online
version of this book, the word Caution appears instead of this symbol.

Warning: Injury to device users may result if ... 
A Warning identifies conditions or inappropriate usage of the product
that could lead to conditions that are potentially hazardous for the
devices users. In the online version of this book, the word Warning
appears instead of this symbol.
Video Encoder EI3 Extender Board Manual
1 USING VIDEO ENCODER EI3
EXTENDER BOARD
This chapter provides the setup procedure for the Video Encoder EI3
Extender Board and describes the interfaces the extender supports.
The information is presented in the following order.
• “Package Contents” on page 1-2
• “Video Encoder EI3 Extender Board Installation” on page 1-2
• “High Performance HDMI Transmitter (ADV7511)” on page 1-3
• “Multi-Format Video Encoder (ADV7431)” on page 1-4
• “Expansion Interface III” on page 1-5
• “Example Programs” on page 1-6
• “Board Design Database” on page 1-7
Video Encoder EI3 Extender Board Manual
1-1
Package Contents
Package Contents
Your Video Encoder EI3 Extender Board package contains the following
items.
• Video Encoder EI3 Extender Board
• A bag containing hardware for securing the extender board on the
EZ-KIT Lite/EZ-Board
• Video cables – one HDMI and one component
• Release note containing information about the product download
Contact the vendor where you purchased your extender board or contact
Analog Devices, Inc. if any item is missing.
Video Encoder EI3 Extender Board
Installation
Follow these instructions to ensure correct operation of the product hardware and software.
1. Attach the extender board to the EZ-KIT Lite/EZ-Board.
The J1 connector on the extender board can be connected to the
P1A, P2A, or P3A connector on the EZ-KIT Lite/EZ-Board. Refer to
the example program for a reference to the proper connector.
2. Use the provided hardware to secure the extender to the EZ-KIT
Lite/EZ-Board. See Figure 1-1.
1-2
Video Encoder EI3 Extender Board Manual
Using Video Encoder EI3 Extender Board
4
4
4
5
4
3
2
5
EZ-Extender 3
(Stacked)
2
1
2
Item
Part Description
1
0.75in Nylon Standoff
2
1.0in Nylon Standoff
3
1.25in Nylon Standoff
4
Nylon Screw
5
Nylon Spacer
1
Figure 1-1. Assembled Board Diagram
3. Refer to the EZ-KIT Lite/EZ-Board manual for information on
connecting to a personal computer (PC) and running CCES.
High Performance HDMI Transmitter
(ADV7511)
The ADV7511 is a 225 MHz high-definition multimedia interface
(HDMI) transmitter, which is ideal for home entertainment products
including DVD players/receivers, digital set top boxes, A/V receivers,
gaming consoles and PCs.
The digital video interface contains an HDMI v1.4 and a DVI v1.0 compatible transmitter and supports all HDTV formats (including 1080p
with 12-bit Deep Color). The ADV7511 supports the HDMI v1.4 spe-
Video Encoder EI3 Extender Board Manual
1-3
Multi-Format Video Encoder (ADV7431)
cific features, HEAC (ARC), and 3D video. In addition, the ADV7511
supports x.v.Color, high bit rate audio and programmable AVI Info
Frames features. With the inclusion of HDCP, the ADV7511 allows the
secure transmission of protected content as specified by the HDCP v1.4
protocol.
The ADV7511 high-performance HDMI transmitter with ARC connects
to the PPI, SPORT, TWI and GPIO of the processor. This device supports up to 1080p.
The ADV7511 can be configured to generate an interrupt based on various events. The TWI port is used for communication between the
transmitter and processor. The PPI is used for transmitting video data.
The SPORT is used for transmitting audio data. An interrupt signal from
the transmitter is connected to a GPIO signal on the processor. The
GPIO signal is configured via a software switch. Refer to “Software-Controlled Switches (SoftConfig)” on page 2-3 for more information.
For more information about the ADV7511, go to www.analog.com and
search for ADV7511.
An example program demonstrating capabilities of the ADV7511 is available by installing the Video Encoder EI3 Extender Board Support Package
(BSP).
Multi-Format Video Encoder (ADV7431)
The ADV7341 is a high speed, digital-to-analog video encoder. Six high
speed, NSV, 3.3V, 12-bit video DACs provide support for composite
(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in
standard definition (SD), enhanced definition (ED), or high definition
(HD) video formats.
The ADV7341 has a 30-bit pixel input port that can be configured in a
variety of ways. SD video formats are supported over an SDR interface
1-4
Video Encoder EI3 Extender Board Manual
Using Video Encoder EI3 Extender Board
and ED/HD video formats are supported over SDR and DDR interfaces.
Pixel data can be supplied in either the YCrCb or RGB color space.
The part also supports embedded EAV/SAV timing codes, external video
synchronization signals, and I2C communication protocol.
In addition, simultaneous SD and ED/HD input and output are supported. Full-drive DACs ensure that external output buffering is not
required, while 216 MHz (SD and ED) and 297 MHz (HD) oversampling
ensures that external output filtering is not required.
The ADV7341 multi-format video encoder connects to the PPI and TWI
of the processor. This device supports up to 1080i/720p.
The TWI port is used for communications between the encoder and processor. The PPI is used for transmitting video data. Refer to
“Software-Controlled Switches (SoftConfig)” on page 2-3 for more
information.
For more information about the ADV7341, go to www.analog.com and
search for ADV7341.
An example program demonstrating capabilities of the ADV7341 is available by installing the Video Encoder EI3 Extender Board Support Package
(BSP).
Expansion Interface III
The Expansion Interface III (EI3) allows an extender board to be tested
across various hardware platforms that have the same expansion interface
connectors.
The EI3 implemented on the Video Encoder EI3 Expander Board contains the PPI, SPORT, TWI and GPIO ports. These signals are used for
the peripherals on the extender. For pinout information, go to
Appendix B, “Video Encoder EI3 Extender Board Schematic”. The
Video Encoder EI3 Extender Board Manual
1-5
Example Programs
mechanical dimensions of the expansion connectors can be obtained by
contacting “Technical Support”.
The Video Encoder EI3 Extender Board supports interfacing with
EZ-Boards which are operating at an IO voltage of 3.3V. Other IO voltages are not supported.
The Video Encoder EI3 Extender Board supports being powered from
either the EZ-Board or through the on board 5V power connector (P1).
For more information about other daughter boards, visit the Analog
Devices Web site.
Limits to current and interface speed must be taken into consideration
when using the EI3. Current for the EI3 can be sourced from the EZ-KIT
Lite/EZ-Board; therefore, the current should be limited to 200 mA for 5V
and 300 mA for the 3.3V planes. If more current is required, then a separate power connector and a regulator must be designed on the daughter
card. Additional circuitry can add extra loading to signals, decreasing their
maximum effective speed.
Devices does not support and is not responsible for the
 Analog
effects of additional circuitry.
Example Programs
Example programs are included with the Video Encoder EI3 Extender
Board Support Package (BSP). Example programs demonstrate various
capabilities of the product. The support package is installed on top of
CrossCore Embedded Studio. Once installed, the example programs can
be found in the following directory:
<install_path>\Video_Encoder_EI3_Extender_Board-RelX.X.X\Video_E
ncoder_EI3,
1-6
where X.X.X denotes the support package release number.
Video Encoder EI3 Extender Board Manual
Using Video Encoder EI3 Extender Board
Board Design Database
A .zip file containing all of the electronic information required for the
design, layout, fabrication, and assembly of the product is available for
download from the Analog Devices board design database at:
http://www.analog.com/en/processors-dsp/blackfin/processors/board-design-database/resources/index.html.
Video Encoder EI3 Extender Board Manual
1-7
Board Design Database
1-8
Video Encoder EI3 Extender Board Manual
2 VIDEO ENCODER EI3
EXTENDER BOARD
HARDWARE REFERENCE
This chapter describes the hardware design of the Video Encoder EI3
Extender Board.
The following topics are covered.
• “System Architecture” on page 2-2
Describes the daughter board configuration and explains how the
board components interface with the processor and EZ-KIT Lite.
• “Software-Controlled Switches (SoftConfig)” on page 2-3
Lists and describes the software-controlled switches.
• “Connectors” on page 2-11
Shows the locations and provides part numbers for the on-board
connectors. In addition, the manufacturer and part number information is provided for the mating parts.
• “LEDs” on page 2-15
Describes the on-board LEDs.
Video Encoder EI3 Extender Board Manual
2-1
System Architecture
System Architecture
A block diagram of the Video Encoder EI3 Extender Board is shown in
Figure 2-1.
3.3V
EI3 Connector
EPPI
TWI
GPIO
1.8V
SPORT
Voltage
Regulation
Bus Transceiver
Power
Soft
Config
MCP23017
Soft
Config
Soft
Config
Soft
Config
74CB3Q16211
PI3C3125
PI3C3125
PPI
TWI
INT
SPORT
ADV7511
HDMI Transmitter
HDMI
Soft
Config
74CB3Q16211
PPI
TWI
ADV7341
Video Encoder
SVIDEO Component Composite
Figure 2-1. Video Encoder EI3 Extender Board Block Diagram
2-2
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Hardware Reference
Software-Controlled Switches
(SoftConfig)
On the Video Encoder EI3 Extender Board, all of the traditional mechanical switches/jumpers have been replaced by I2C software-controlled
switches. Refer to any SoftConfig*.c file found in the installation directory of CCES for an example of how to set up the SoftConfig feature of
the product through software.
The SoftConfig section of this manual serves as a reference to any user
that intends to modify an existing software example. If software provided
by ADI is used, there should be little need to reference this section.
should be taken when changing SoftConfig settings not to
 Care
create a conflict with interfaces. The same GPIO signal and SPICS
should not be configured for more than one interface.
Overview of SoftConfig
In order to further clarify the use of electronic single FET switches and
multi-channel bus switches, an example of each is illustrated and compared to a traditional mechanical switching solution. This is a generic
example. After this generic discussion there is a detailed explanation of the
SoftConfig interface specific to the extender.
Figure 2-2 shows two individual FET switches (Pericom PI3A125CEX)
with reference designators UA and UB. Net names ENABLE_A and ENABLE_B
control UA and UB. The default FET switch enable settings in this example
are controlled by resistors RA and RB which pull the enable pin 1 of UA and
UB to ground (low). In a real example, these enable signals are controlled
by the Microchip IO expander. The default pull-down resistors connect
the signals EXAMPLE_SIGNAL_A and EXAMPLE_SIGNAL_B and also connect signals EXAMPLE_SIGNAL_C and EXAMPLE_SIGNAL_D. To disconnect
EXAMPLE_SIGNAL_A from EXAMPLE_SIGNAL_B, the Microchip IO expander is
Video Encoder EI3 Extender Board Manual
2-3
Software-Controlled Switches (SoftConfig)
used to change ENABLE_A to a logic 1 through software that interfaces with
the Microchip. The same procedure for ENABLE_B would disconnect
EXAMPLE_SIGNAL_C from EXAMPLE_SIGNAL_D.
Figure 2-2. Example of Individual FET Switches
Figure 2-3 shows the equivalent circuit to Figure 2-2 but utilizes mechanical switches that are in the same package. The default is shown by black
boxes located closer to the ON label of the switches. In order to disconnect
these switches, physically move the switch to the OFF position.
Figure 2-3. Example of Mechanical Switch Equivalent to Figure 2-2
2-4
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Hardware Reference
Figure 2-4 shows a bus switch example, reference designator UC (Pericom
PI3LVD512ZHE), selecting between lettered functionality and numbered
functionality. The signals on the left side are multiplexed signals with
naming convention letter_number.
Figure 2-4. Example of Bus Switch
The right side of the circuit shows the signals separated into letter and
number, with the number on the lower group (eg. 0B1) and the letter on
the upper group (eg. 0B2). The default setting is controlled by the signal
CONTROL_LETTER_NUMBER which is pulled low. This selects the number signals on the right to be connected to the multiplexed signals on the left by
Video Encoder EI3 Extender Board Manual
2-5
Software-Controlled Switches (SoftConfig)
default. In this example, the Microchip IO expander is not shown but
controls the signal CONTROL_LETTER_NUMBER and allows the user to change
the selection through software.
Figure 2-5 shows the equivalent circuit to Figure 2-4 but utilizes mechanical switches. Notice the default for reference designators SWC and SWD is
illustrated by black boxes located closer to the ON label of the switches to
enable the number signals by default. Note the default setting for reference designators SWE and SWF is OFF. In order to connect the letters instead
of the numbers, the user physically changes all switches on SWC and SWD to
the OFF position and all switches on SWE and SEF to the ON position.
Figure 2-5. Example of Mechanical Switch Equivalent to Figure 2-4
2-6
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Hardware Reference
Programming SoftConfig
On the Video Encoder EI3 Extender Board, a single Microchip
MCP23017 device controls individual and electronic bus switches via
TWI. The device has the following programming characteristics:
• There are two programmable GPIO registers.
GPIO Register
Register Address
GPIOA
0x12
GPIOB
0x13
• Each GPIO register controls eight signals (software switches).
• By default, the GPIO signals function as input signals; therefore,
all electronic switches are in the OFF state.
The signals must be programmed as output signals to override their
default values. The following table shows the Microchip register
addresses and values that must be written to them to program the
signals as output signals.
IODIR Register IODIR Register Address Value to be Written to Program Signals
as Outputs
IODIRA
0x00
0
IODIRB
0x01
0
Video Encoder EI3 Extender Board Manual
2-7
Software-Controlled Switches (SoftConfig)
Each example in Cross Core Embedded Studio includes source files that
program the soft switches, even if the default settings are being used. The
README for each example identifies only the signals that are being changed
from their default values. The code that programs the soft switches is
located in two files:
•
SoftConfig_Encoder.c
•
SoftConfig_xxx.c
for configuring the extender board
for configuring the EZ-KIT Lite/EZ-Board; 
xxx identifies the EZ-KIT Lite/EZ-Board file in each example.
Page 2 of Appendix B, “Video Encoder EI3 Extender Board Schematic”
shows how the GPIO signals are connected to the board’s ICs.
and U10-U13 are 24-bit bus switches. They are used to select how the
transmitter/encoder is connected to the processor. You can select an 8-bit,
16-bit, or 24-bit interface.
U13
are 2-port bus switches. They are used for selecting which GPIO
signals to use as the interrupt.
U8-U9
is an 8-port bus switch. It is used to connect/disconnect the SPORT
to the ADV7511.
U18
Table 2-1 and Table 2-2 show the output signals of the GPIO expander
(U10) with a TWI address of 0100 101X, where X represents the read or
write bit. The signals that control an individual FET have an entry under
the FET column. The Component Connected column shows the board
IC that is connected if the FET is enabled.
2-8
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Hardware Reference
Table 2-1. Output Signals of GPIO Expander (U19 Port A)
Bit Signal Name
Description
FET
Component
Connected
Default
0
24_BIT_ADV7511
24-bit video mode
U10
U14
Off
1
24_BIT_ADV7341
24-bit video mode
U11
U2
Off
2
16_BIT_ADV7511
16-bit video mode
U13
U14
Off
3
16_BIT_ADV7341
16-bit video mode
U12
U2
Off
4
27MHZ_CLK_EN
Enable 27 MHz oscillator
U15
Off
5
74MHZ_CLK_EN
Enable 74 MHz oscillator
U14
Off
6
8_BIT_ADV7341
8-bit video mode
U3
U2
Off
7
SPORT_ENABLE
Enable SPORT interface
U18
U14
Off
Table 2-2. Output Signals of GPIO Expander (U19 Port B)
Bit Signal Name
Description
FET
Component
Connected
Default
0
ADV7511_INT_GPIO0
Transmitter interrupt
U9
U14
Off
1
ADV7511_INT_GPIO1
Transmitter interrupt
U9
U14
Off
2
ADV7511_INT_GPIO2
Transmitter interrupt
U19
U14
Off
3
ADV7511_INT_GPIO3
Transmitter interrupt
U9
U14
Off
4
ADV7511_INT_GPIO4
Transmitter interrupt
U8
U14
Off
5
ADV7511_INT_GPIO5
Transmitter interrupt
U8
U14
Off
6
ADV7511_INT_GPIO6
Transmitter interrupt
U8
U14
Off
7
ADV7511_INT_GPIO7
Transmitter interrupt
U8
U14
Off
Video Encoder EI3 Extender Board Manual
2-9
Software-Controlled Switches (SoftConfig)
Video Encoder Mode Select
The Video Encoder Mode Select determines whether the interface to the
processors PPI is 8, 16 or 24 bits. The Video Encoder Mode select is chosen by driving low either the 24_BIT_ADV7511, 16_BIT_ADV7511,
24_BIT_ADV7341, 16_BIT_ADV7341 or 8_BIT_ADV7341 signal (U20 ports
GPA0-GPA3, GPA6. Driving one of these signals low enables the appropriate
bus switches (U10-U13 and U3).
ADV7511_INT_GPIOx Signal
The ADV7511_INT_GPIOx signal connects the interrupt signal of the
ADV7511 to one of eight GPIO pins of the processor. U20 ports
GPB0-GPB7 are used to select the connection to the appropriate GPIO signal via the U8 and U9 bus switch.
27MHZ_CLK_EN Signal
The 27MHZ_CLK_EN signal is used to enable the onboard 27 MHz oscillator
which connects to the ADV7511 and ADV7341. U20 port GPA4 is used to
enable and disable the oscillator. The default is disabled.
74MHZ_CLK_EN Signal
The 74MHZ_CLK_EN signal is used to enable the onboard 74.25 MHz oscillator which connects to the ADV7511 and ADV7341. U20 port GPA5 is
used to enable and disable the oscillator. The default is disabled.
SPORT_ENABLE Signal
The SPORT_ENABLE signal connects the audio signal of the ADV7511 to the
SPORT interface of the processor. U20 port GPA7 is used to enable or disable the connection via the U18 bus switch. The default is disabled.
2-10
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Hardware Reference
Connectors
This section describes connector functionality and provides information
about mating connectors. Figure 2-6 shows the locations of all connectors
on the Video Encoder EI3 Extender Board.
Figure 2-6. Connector Locations
denoted by a dotted line are located on the opposite
 Connectors
side of the board.
Video Encoder EI3 Extender Board Manual
2-11
Connectors
Expansion III (EI3) Connectors (J4)
One board-to-board connectors (J4) provide signals from the PPI,
SPORT, TWI, and GPIO interfaces of the processor. The connector is
located on the bottom side of the board.
Part Description
Manufacturer
Part Number
120-pin, 0.6 mm
HIROSE
FX8-120S-SV(21)
Mating Connector
120-pin, 0.6 mm
HIROSE
FX8-120P-SV1(91)
S-Video Connector (J2)
The S-Video connector (J2) is a DIN connector which connects to the
ADV7341. This connector can be used for Y-C mode and supports SD,
ED, and HD video modes.
Part Description
Manufacturer
Part Number
S-Video
CUI
MD-40SM
Mating Cable
S-Video Cable
2-12
Belkin
F8V308-06
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Hardware Reference
Component Connector (J14)
The Component connector (J14) is a group of three RCA jacks which
connect to the ADV7341. This connector can be used for YPrPb and
RGB modes and supports SD, ED, and HD video modes.
Part Description
Manufacturer
Part Number
Component (3x1 RCA)
CUI
RCJ-32265
Mating Cable
Component Cable
Belkin
AV21000-06
HDMI Connector (J5)
The HDMI connector (J5) is an HDMI receptacle that is connected to
the ADV7511. This connector can be used for YCbCr and RGB modes
and supports SD, ED, and HD video modes. It supports ARC and is v.1.4
compliant.
Part Description
Manufacturer
Part Number
HDMI
FCI
10029449-002TLF
Mating Cable
HDMI Cable
Mediabridge
Video Encoder EI3 Extender Board Manual
91-02X-06B
2-13
Connectors
Composite Connector (J6)
The Composite connector (J6) is a single RCA jack which connects to the
ADV7341. This connector can be used for CVBS and supports SD, ED,
and HD video modes.
Part Description
Manufacturer
Part Number
Composite (1 RCA)
Switchcraft
PJRAN1X1U01X
Mating Cable
Composite Cable
Kobiconn
17FH101
Power Connector (P1)
Under normal circumstances the power connector is not needed because
the Video Encoder EI3 Extender Board derives its power from the
EZ-KIT Lite/EZ-Board. If the EZ-KIT Lite/Video Encoder EI3 Extender
Board is not able to supply enough power to the Video Encoder EI3
Extender Board, then an external power supply can be connected to P14
which will power the Video Encoder EI3 Extender Board and EZ-KIT
Lite/EZ-Board.
Part Description
Manufacturer
Part Number
0.65 mm power jack
CUI
045-0883R
Mating Cable
5.0VDC@3.6A power supply
2-14
GLOBETEK
GS-1750(R)
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Hardware Reference
LEDs
This section describes the on-board LEDs.
HDMI Detect LED (LED1)
When LED1 is lit solid (yellow), it indicates that an HDMI device has been
detected (connected to the HDMI connector (J5)).
Power LED (LED2)
When LED2 is lit solid (green), it indicates that power is being supplied to
the board properly.
Video Encoder EI3 Extender Board Manual
2-15
LEDs
2-16
Video Encoder EI3 Extender Board Manual
A VIDEO ENCODER EI3
EXTENDER BOARD BILL OF
MATERIALS
The bill of materials corresponds to “Video Encoder EI3 Extender Board
Schematic” on page B-1.
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
1
1
SN74LVC1G125 SOT23-5
U22
TI
74LVC1G125DBVRE4
2
2
SN74LVC1G04 SOT23-5
U4-U5
TI
SN74LVC1G04DBVT
3
1
27MHZ OSC003
U15
EPSON
SG-8002CA-MP
4
5
SN74CB3Q16211 TSSOP56
U3,U10-U13
DIGI-KEY
296-17629-1-ND
5
1
SN74AVC4T245 SOIC16
U1
DIGI-KEY
296-17930-1-ND
6
1
SN74AVC8T245 TSSOP24
U18
TI
SN74AVC8T245PW
7
1
12MHZ OSC015
U17
DIGI-KEY
535-9413-2-ND
8
1
MCP23017
QFN65P600X600-29N
U19
DIGI-KEY
MCP23017-E/ML-ND
9
3
PI3C3125 TSSOP14
U7-U9
PERICOM
PI3C3125
10
1
74.25MHZ OSC003
U16
CTS
CB3LV-3I-74M2500
11
1
74AVC24T245 LFBGA84
U6
DIGI-KEY
296-17662-1-ND
12
1
ADV7341BSTZ LQFP64
U2
ADI
ADV7341BSTZ
13
3
ADA4430 SC70_6
U23-U25
ADI
ADA4430-1YKSZ-R2
14
1
ADP1706-1.8V LFCSP8
VR2
ADI
ADP1706ACPZ-1.8-R7
15
1
ADP1706-3.3V LFCSP8
VR1
ADI
ADP1706ACPZ-3.3-R7
16
1
10MA AD1580BRTZ
SOT23D
D7
ADI
AD1580BRTZ-R2
Video Encoder EI3 Extender Board Manual
A-1
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
17
1
ADV7511KSTZ LQFP100
U14
ADI
ADV7511KSTZ
18
1
RCA 1X1 CON012
J6
SWITCHCRAFT
PJRAN1X1U01X
19
1
PWR .65MM CON027
P1
DIGI-KEY
CP1-022PJCT-ND
20
1
1A RESETABLE 1206
F1
RAYCHEM
NANOSMDC110F-2
21
1
HDMI 19P
FCI_10029449-002TLF
J5
FCI
10029449-002LF
22
1
RCA 3X1
CUI-STACK_RCJ-32265
J1
DIGI-KEY
CP-1446-ND
23
1
MINI-DIN 4PIN
CUI-STACK_MD-40SM
J2
DIGI-KEY
CP-2240-ND
24
1
.6MM 120PIN
HIROSE_FX8-120S-SV(21)
J4
HIROSE
FX8-120S-SV(21)
25
1
YELLOW LED001
LED1
DIGI-KEY
P512TR-ND
26
3
10K 1/10W 5% 0805
R5,R7,R9
VISHAY
CRCW080510K0JNEA
27
3
10K 1/10W 5% 0805
R6,R8,R10
VISHAY
CRCW080510K0JNEA
28
2
10K 31MW 5% RNET8
RN1-RN2
CTS
746X101103JP
29
9
10UH 10% 1008
L1-L9
PANASONIC
ELJ-FC100KF
30
9
10UF 6.3V 10% 0805
C22,C49,C58,
C66,C68,
C84-C85,C92,
C95
AVX
08056D106KAT2A
A-2
Video Encoder EI3 Extender Board Manual
Video Encoder EI3 Extender Board Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
31
45
0.1UF 10V 10% 0402
C1-C4,C7-C12,
C14-C19,C23,
C26,C29-C30,
C35-C37,C40,
C43-C44,C51,
C53-C54,C57,
C60-C62,C64,
C70,C72-C73,
C76-C77,C80,
C82,C87,C90,
C93,C96
AVX
0402ZD104KAT2A
32
19
0.01UF 16V 10% 0402
C41-C42,C45,
C48,C50,C52,
C55-C56,C59,
C65,C69,C71,
C74-C75,C81,
C83,C86,C91,
C94
AVX
0402YC103KAT2A
33
12
10K 1/16W 5% 0402
R3-R4,
R14-R16,R18,
R25,R28-R29,
R40,R43,R46
VISHAY
CRCW040210K0FKED
34
2
4.7K 1/16W 5% 0402
R30,R38
VISHAY
CRCW04024K70JNED
35
2
0 1/16W 5% 0402
R57-R58
PANASONIC
ERJ-2GE0R00X
36
7
0 1/16W 5% 0402
R11,R13,
R26-R27,R49-R
51
PANASONIC
ERJ-2GE0R00X
37
5
33 1/16W 5% 0402
R1-R2,R12,
R17,R56
VISHAY
CRCW040233R0JNEA
38
2
2.2UF 10V 10% 0805
C38-C39
AVX
0805ZD225KAT2A
39
4
4.7UF 6.3V 20% 0603
C46-C47,C63,
C67
AVX
06036D475MAT2A
40
6
75.0 1/10W 1% 0603
R41-R42,
R47-R48,
R52-R53
DALE
CRCW060375R0FKEA
Video Encoder EI3 Extender Board Manual
A-3
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
41
2
1UF 6.3V 20% 0402
C20-C21
PANASONIC
ECJ-0EB0J105M
42
1
GREEN LED001
LED2
PANASONIC
LN1361CTR
43
1
1.1K 1/16W 1% 0402
R37
PANASONIC
ERJ-2RKF1101X
44
2
430 1/16W 1% 0402
R19,R54
DIGI-KEY
311-430LRCT-ND
45
1
VARISTOR V5.5MLA 30A
0603
R55
LITTLEFUSE
V5.5MLA0603
46
2
0.15UF 10V 10% 0603
C31,C33
AVX
0603ZC154KAT2A
47
3
1A MBR130LSFT1G
SOD-123FL
D4-D6
ON SEMI
MBR130LSFT1G
48
1
27K 1/16W 5% 0402
R20
PANASONIC
ERJ-2GEJ273X
49
8
4700PF XXX 2A
FIL_NFE61PT
FER1-FER8
DIGI-KEY
490-2554-2-ND
50
1
887 1/10W 1% 0603
R32
DIGI-KEY
311-887HRTR-ND
51
3
5A RCLAMP0524
DIO_RCLAMP0524
D9-D11
SEMTECH
RCLAMP0524P.TCT
52
1
30MA DB3X314
DIO_DB3X314
D8
PANASONIC
DB3X314K0L
53
2
49.9 1/16W 1% 0402
R23-R24
STACKPOLE
RMCF0402FT49R9
54
3
2.0K 1/10W 1% 0402
R21-R22,R31
PANASONIC
ERJ-2RKF2001X
55
1
4.12K 1/10W 1% 0402
R33
PANASONIC
ERJ-2RKF4121X
56
2
0.012UF 10V 10% 0402
C32,C34
DIGI-KEY
399-3009-2-ND
57
2
169.0 1/10W 1% 0402
R35-R36
PANASONIC
ERJ-2RKF1690X
58
1
510.0 1/10W 1% 0402
R34
PANASONIC
ERJ-2RKF5100X
59
3
300.0 1/10W 1% 0402
R39,R44-R45
PANASONIC
ERJ-2RKF3000X
61
3
100MA BAT54S SOT23D
D1-D3
FAIRCHILD
BAT54S
A-4
Video Encoder EI3 Extender Board Manual
A
B
D
C
1
1
Video Encoder EI3 Extender Board
Schematic
2
2
3
3
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
Title Sheet
Board No.
Rev
A0252-2010
C
Date
20 Cotton Road
1.0
Sheet
3/6/12
D
1
of
8
A
B
D
C
J4
94
EI3_PPICLK
95
EI3_PPIFS2
101
EI3_PPID0
102
EI3_PPID2
103
EI3_PPID4
105
EI3_PPID6
106
EI3_PPID8
107
EI3_PPID10
108
EI3_PPID12
1
12
EI3_PPID14
111
EI3_PPID16
112
EI3_PPID18
113
EI3_PPID20
114
EI3_PPID22
99
87
EI3_SPORT0_CLK
89
EI3_SPORT0_FS
29
88
EI3_SPORT0_D0
32
EI3_SPORT0_D1
35
82
83
33
39
37
61
2
56
79
EI3_SCL
80
EI3_SDA
PPI0_CLK
27
PPI0_FS1
EI3_PPIFS1
PPI0_FS2
26
PPI0_FS3
EI3_PPIFS3
PPI0_D0
20
PPI0_D1
EI3_PPID1
PPI0_D2
19
PPI0_D3
EI3_PPID3
PPI0_D4
18
PPI0_D5
EI3_PPID5
PPI0_D6
16
PPI0_D7
EI3_PPID7
PPI0_D8
15
PPI0_D9
EI3_PPID9
PPI0_D10
14
PPI0_D11
EI3_PPID11
PPI0_D12
13
PPI0_D13
EI3_PPID13
U19
PPI0_D14
110
PPI0_D15
EI3_PPID15
10
PPI0_D17
5
VDD
PPI0_D16
EI3_PPID17
PPI0_D18
9
PPI0_D19
EI3_PPID19
EI3_SCL
PPI0_D20
8
PPI0_D21
EI3_PPID21
EI3_SDA
PPI0_D22
7
PPI0_D23
EI3_PPID23
TWI Address 0100 101x
x is the R/W bit. Read - 1, Write - 0
SoftConfig control signals
3.3V
8
SCL
R11
0402
0
9
SDA
14
RESET
EI3_RESET
PPI0_INT
SPORT0_CLK
SPORT0_FS
SPORT0_TDV
3.3V
92
SPORT1_CLK
90
SPORT1_FS
EI3_SPORT1_CLK
EI3_SPORT1_FS
91
SPORT1_D0
SPORT0_D1
31
SPORT1_D1
SPI0_MISO
SPI0_D2
EI3_SPORT1_CLK
R58
0
0402
DNP
EI3_SPORT1_D0
EI3_SPORT1_D1
SPORT_INT
SPI0_CLK
15
INTB
EI3_SPORT0_CLK
30
SPORT1_TDV
SPORT0_D0
16
INTA
R57
0
0402
DNP
EI3_SPORT0_FS
R10
10K
0805
EI3_SPORT1_FS
R9
10K
0805
DNP
R8
10K
0805
1
17
GPA0
24_BIT_ADV7511
18
GPA1
24_BIT_ADV7341
19
GPA2
16_BIT_ADV7511
20
GPA3
16_BIT_ADV7341
21
GPA4
27MHZ_CLK_EN
22
GPA5
74MHZ_CLK_EN
23
GPA6
8_BIT_ADV7341
24
GPA7
SPORT_ENABLE
25
GPB0
ADV7511_INT_GPIO0
26
GPB1
ADV7511_INT_GPIO1
27
GPB2
ADV7511_INT_GPIO2
28
GPB3
ADV7511_INT_GPIO3
1
GPB4
ADV7511_INT_GPIO4
50
SPI0_RDY
11
A0
2
GPB5
ADV7511_INT_GPIO5
84
SPI0_MOSI
12
A1
3
GPB6
ADV7511_INT_GPIO6
13
4
GPB7
ADV7511_INT_GPIO7
34
SPI0_D3
SPI0_SEL1/SPI0_SS*
85
SPI0_SEL_A
SPI0_SEL_B
SPI0_SEL_C
A2
MCP23017
QFN65P600X600-29N
38
R7
10K
0805
DNP
EXT_BOOT
R6
10K
0805
R5
10K
0805
DNP
2
TWI0_A0*
SCL0*
42
SCL1*
SDA0*
41
SDA1*
GPIO0
78
GPIO1
EI3_GPIO1
GPIO2
77
GPIO3
EI3_GPIO3
GPIO4
76
GPIO5
EI3_GPIO5
GPIO6
74
GPIO7*
EI3_GPIO7
3.3V
43
EI3_GPIO0
44
EI3_GPIO2
45
EI3_GPIO4
47
EI3_GPIO6
48
49
3.3V
3.3V
C96
0.1UF
0402
73
TMR_A
TMR_B
TMR_C
72
TMR_D*
R25
10K
0402
R4
10K
0402
U15
59
UART0_RX
62
UART0_TX
U4
1
OE
65
60
PWR_IN
VIN
WAKE*
RESET_IN*
64
SLEEP*
3
R3
10K
0402
EI3_RESET
USB_VCC
71
OUT
3.3V
GND
27MHZ 2
OSC003
SN74LVC1G04
SOT23-5
57
RESET_OUT*
R1
33
0402
4
VDD
TP7
U7
CLKOUT
R56
33
0402
1
OE0
27MHZ_CLK_EN
2
3
1
120
VIN
PS_IN
116
VIO
6
17
28
40
52
63
75
86
98
109
117
2
22
25
53
55
4
67
70
97
119
GND1
4
GND2
GND3
11
GND4
GND5
23
GND6
GND7
36
GND8
GND9
46
GND10
GND11
58
GND12
GND13
69
GND14
GND15
GND16
GND17
93
GND18
GND19
104
GND20
GND21
115
GND22
GND23
118
GND24
RSVD1
21
RSVD2
RSVD3
24
RSVD4
RSVD5
51
RSVD6
RSVD7
54
RSVD8
RSVD9
66
RSVD10
RSVD11
68
RSVD12
RSVD13
96
RSVD14
RSVD15
100
RSVD16
PPICLK
3
4
74MHZ_CLK_EN
OE1
5
A1
3.3V
3
3
B0
A0
5
USB_VCC
6
B1
10
OE2
9
A2
8
B2
13
OE3
U16
U5
1
R2
33
0402
4
VDD
OE
OUT
12
A3
11
B3
PI3C3125
TSSOP14
3
TP16
GND
74.25MHZ 2
OSC003
SN74LVC1G04
SOT23-5
81
3.3V
3.3V
C30
0.1UF
0402
C29
0.1UF
0402
3.3V
C2
0.1UF
0402
C3
0.1UF
0402
C4
0.1UF
0402
ANALOG
DEVICES
Title
RSVD17
HIROSE_FX8-120S-SV(21)
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
EI3 Connector/GPIO Extender
Board No.
Rev
A0252-2010
C
Date
20 Cotton Road
1.0
Sheet
3/6/12
D
2
of
8
A
B
D
C
3.3V
3.3V
3.3V
U6
3.3V
B4
VCCA1
VCCB1
D4
VCCA2
VCCB2
H4
VCCA3
VCCB3
L4
VCCA4
VCCB4
N4
VCCA5
1
EI3_PPID0
B6
1A1
EI3_PPID1
B5
1A2
1B2
EI3_PPID2
C6
1A3
1B3
EI3_PPID3
C5
1A4
1B4
EI3_PPID4
D6
2A1
2B1
EI3_PPID5
D5
2A2
2B2
EI3_PPID6
E6
2A3
2B3
EI3_PPID7
E5
2A4
2B4
F6
EI3_PPID8
1B1
3A1
3B1
EI3_PPID9
F5
3A2
3B2
EI3_PPID10
G6
3A3
3B3
EI3_PPID11
G5
3A4
3B4
H6
EI3_PPID12
4A1
4B1
EI3_PPID13
H5
4A2
4B2
EI3_PPID14
J6
4A3
4B3
EI3_PPID15
J5
4A4
EI3_PPID16
K6
5A1
5B1
EI3_PPID17
K5
5A2
5B2
4B4
L6
EI3_PPID18
5A3
5B3
L5
EI3_PPID19
5A4
5B4
M6
EI3_PPID20
2
VCCB5
6A1
6B1
M5
EI3_PPID21
6A2
6B2
N6
EI3_PPID22
6A3
6B3
N5
EI3_PPID23
3.3V
R14
10K
0402
6A4
6B4
A6
1OE
GND1
P6
1DIR
GND2
A5
2OE
GND3
P5
2DIR
GND4
A4
3OE
GND5
P4
3DIR
GND6
A3
4OE
GND7
P3
4DIR
GND8
A2
5OE
GND9
P2
5DIR
GND10
A1
6OE
GND11
P1
6DIR
GND12
GND13
3.3V
B3
C10
0.1UF
0402
D3
C36
0.1UF
0402
C37
0.1UF
0402
C61
0.1UF
0402
H3
L3
C12
0.1UF
0402
N3
B1
C11
0.1UF
0402
PPID0
B2
PPID1
C1
1
3.3V
PPID2
C2
3.3V
3.3V
PPID3
D1
3.3V
PPID4
D2
C9
0.1UF
0402
PPID5
E1
PPID6
E2
C62
0.1UF
0402
C76
0.1UF
0402
C77
0.1UF
0402
U18
PPID7
F1
R16
10K
0402
PPID8
F2
1
VCC_A
23
VCC_B1
24
VCC_B2
PPID9
G1
PPID10
G2
H1
H2
J1
J2
K2
L1
L2
B1
PPID11
EI3_SPORT0_D1
PPID12
EI3_SPORT1_D0
5
A3
PPID13
EI3_SPORT1_D1
6
A4
B4
PPID14
EI3_SPORT0_CLK
7
A5
B5
EI3_SPORT0_FS
8
A6
20
B2
B3
19
18
17
16
B6
PPID16
9
A7
B7
PPID17
10
A8
B8
SPORT0_D0
SPORT0_D1
SPORT1_D0
SPORT1_D1
SPORT0_CLK
SPORT0_FS
15
14
PPID18
2
DIR
GND1
PPID19
22
OE
GND2
SPORT_ENABLE
M1
21
A1
4
A2
PPID15
K1
3
EI3_SPORT0_D0
11
12
PPID20
13
GND3
M2
PPID21
N1
2
SN74AVC8T245
TSSOP24
PPID22
N2
PPID23
C3
C4
E3
E4
F3
F4
G4
3.3V
3.3V
J3
J4
K3
K4
RN2
M3
C15
0.1UF
0402
M4
C26
0.1UF
0402
24_BIT_ADV7341
R3
4
R4
6
27MHZ_CLK_EN
R5
7
74MHZ_CLK_EN
3
R6
3.3V
ADV7511_INT_GPIO0
EI3_GPIO0
9
R15
10K
0402
ADV7511_INT_GPIO1
U1
1
VCCA
4
PPICLK
13
1A1
1B1
5
EI3_PPIFS1
12
1A2
1B2
6
EI3_PPIFS2
11
2A1
2B1
7
EI3_PPIFS3
16
VCCB
EI3_GPIO1
R12
0402
33
EI3_PPICLK
ADV7511_INT_GPIO2
PPIFS1
EI3_GPIO2
PPIFS2
ADV7511_INT_GPIO3
10
2A2
2B2
2
EI3_GPIO3
15
1OE
1DIR
3
RN1
3
B0
ADV7511_INT
5
A1
ADV7511_INT_GPIO1
6
B1
9
A2
12
A3
ADV7511_INT_GPIO4
EI3_GPIO4
3.3V
ADV7511_INT_GPIO5
3.3V
EI3_GPIO5
ADV7511_INT_GPIO6
EI3_GPIO6
C8
0.1UF
0402
ADV7511_INT_GPIO7
C7
0.1UF
0402
EI3_GPIO7
R5
7
R6
8
ADV7511_INT_GPIO6
R7
9
ADV7511_INT_GPIO7
R8
U8
1
OE0
2
A0
10K
RNET8
B0
3
4
OE1
5
A1
6
B1
10
OE2
9
A2
ANALOG
DEVICES
8
B2
13
OE3
12
A3
11
B3
Title
Size
Date
C
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
Voltage Translators
Board No.
Rev
A0252-2010
C
B
R4
6
B3
PI3C3125
TSSOP14
A
R3
ADV7511_INT_GPIO5
11
10
COM2
4
ADV7511_INT_GPIO4
13
OE3
2
R2
ADV7511_INT_GPIO3
8
B2
5
COM1
3
ADV7511_INT_GPIO2
10
OE2
1
R1
ADV7511_INT_GPIO0
4
OE1
14
SN74AVC4T245
SOIC16
4
10K
RNET8
PI3C3125
TSSOP14
2OE
2DIR
R8
U9
1
OE0
2
A0
3.3V
R7
SPORT_ENABLE
TP4
3
8
8_BIT_ADV7341
3.3V
10
COM2
3
16_BIT_ADV7341
TP17
2
R2
16_BIT_ADV7511
TP5
5
COM1
R1
24_BIT_ADV7511
74AVC24T245
LFBGA84
1
1.0
Sheet
3/6/12
D
3
of
8
A
B
D
C
3.3V
3.3V
TP8
2
PPID0
3
PPID1
PPID2
4
1A3
52
1B3
ADV7511_D6
PPID3
5
1A4
51
1B4
ADV7511_D7
PPID4
6
1A5
50
1B5
ADV7511_D8
4
PPID2
5
PPID3
6
PPID4
PPID5
7
1A6
48
1B6
ADV7511_D9
PPID6
9
1A7
47
1B7
ADV7511_D10
7
PPID5
9
PPID6
PPID7
10
1A8
46
1B8
ADV7511_D11
PPID8
11
1A9
45
1B9
ADV7511_D16
PPID9
12
1A10
44
1B10
ADV7511_D17
10
PPID7
11
PPID8
PPID10
13
1A11
43
1B11
ADV7511_D18
PPID11
14
1A12
42
1B12
ADV7511_D19
12
PPID9
3.3V
13
PPID10
14
PPID11
56
1OE
56
PPID12
15
2A1
41
2B1
ADV7511_D20
PPID13
16
2A2
40
2B2
ADV7511_D21
PPID14
18
2A3
39
2B3
ADV7511_D22
PPID15
20
2A4
37
2B4
ADV7511_D23
C14
0.1UF
0402
15
PPID12
16
PPID13
18
PPID14
20
PPID15
PPID16
21
2A5
36
2B5
PPID17
22
2A6
35
2B6
PPID18
23
2A7
34
2B7
PPID19
24
2A8
33
2B8
ADV7511_D31
PPID20
25
2A9
32
2B9
ADV7511_D32
PPID21
26
2A10
31
2B10
ADV7511_D33
PPID22
27
2A11
30
2B11
ADV7511_D34
PPID23
28
2A12
29
2B12
ADV7511_D28
21
PPID16
ADV7511_D29
22
PPID17
ADV7511_D30
23
PPID18
24
PPID19
25
PPID20
26
PPID21
27
PPID22
ADV7511_D35
28
PPID23
53
1B2
ADV7341_C3
1A3
52
1B3
ADV7341_C4
1A4
51
1B4
ADV7341_C5
1A5
50
1B5
ADV7341_C6
1A6
48
1B6
ADV7341_C7
1A7
47
1B7
ADV7341_C8
1A8
46
1B8
ADV7341_C9
1A9
45
1B9
ADV7341_Y2
1A10
44
1B10
ADV7341_Y3
1A11
43
1B11
ADV7341_Y4
1A12
42
1B12
ADV7341_Y5
1
3.3V
1OE
3.3V
2A1
41
2B1
ADV7341_Y6
2A2
40
2B2
ADV7341_Y7
2A3
39
2B3
ADV7341_Y8
2A4
37
2B4
ADV7341_Y9
2A5
36
2B5
ADV7341_S2
C16
0.1UF
0402
TP6
U3
ADV7341_S3
2A7
34
2B7
ADV7341_S4
2A8
33
2B8
ADV7341_S5
2A10
31
2B10
ADV7341_S7
ADV7341_S8
2A12
29
2B12
ADV7341_S9
ADV7341_S5
6
50
1B5
ADV7341_S6
7
48
1B6
ADV7341_S7
9
47
1B7
ADV7341_S8
10
46
1B8
ADV7341_S9
11
45
1B9
12
44
1B10
13
43
1B11
14
42
1B12
1A6
PPID6
30
2B11
51
1B4
1A5
PPID5
2A11
ADV7341_S4
5
1A4
PPID4
ADV7341_S6
52
1B3
1A3
PPID3
32
2B9
ADV7341_S3
4
1A2
PPID2
2A9
ADV7341_S2
53
1B2
1A1
PPID1
35
2B6
54
1B1
3
2
PPID0
2A6
1A7
PPID7
1A8
SN74CB3Q16211
TSSOP56
24-Bit Mode
RGB 4:4:4
1A10
GND3
49
GND4
2OE
GND2
GND2
38
GND3
49
GND4
55
24_BIT_ADV7341
19
1A11
1A12
24-Bit Mode
RGB 4:4:4
1OE
15
41
2B1
16
40
2B2
18
39
2B3
20
37
2B4
21
36
2B5
22
35
2B6
23
34
2B7
24
33
2B8
2A1
3.3V
2A2
2A3
2A4
3.3V
2A5
TP11
2A6
5
1A4
51
1B4
PPID4
6
1A5
50
1B5
ADV7511_D24
PPID5
7
1A6
48
1B6
ADV7511_D25
PPID6
9
1A7
47
1B7
ADV7511_D26
10
1A8
PPID7
46
1B8
ADV7511_D23
PPID3
PPID4
PPID5
PPID6
ADV7511_D27
PPID7
PPID8
11
1A9
45
1B9
ADV7511_D28
PPID9
12
1A10
44
1B10
ADV7511_D29
PPID8
PPID10
13
1A11
43
1B11
ADV7511_D30
PPID11
14
1A12
42
1B12
ADV7511_D31
PPID9
3.3V
PPID10
PPID11
56
1OE
5
6
7
9
10
11
12
13
14
56
PPID12
15
2A1
41
2B1
ADV7511_D32
PPID13
16
2A2
40
2B2
ADV7511_D33
C18
0.1UF
0402
PPID12
PPID13
15
16
37
2B4
ADV7511_D35
21
2A5
36
2B5
22
2A6
35
2B6
23
2A7
34
2B7
23
24
2A8
33
2B8
24
25
2A9
32
2B9
26
2A10
31
2B10
26
27
2A11
30
2B11
27
28
2A12
29
2B12
16-Bit Mode
YCbCr 4:2:2
A
PPID14
PPID15
18
20
21
22
25
28
16_BIT_ADV7341
55
17
VCC
27
52
1B3
30
2B11
1A3
ADV7341_C4
28
51
1B4
29
2B12
1A4
ADV7341_C5
1A5
50
1B5
ADV7341_C6
1A6
48
1B6
ADV7341_C7
1A7
47
1B7
ADV7341_C8
1A8
46
1B8
ADV7341_C9
1A9
45
1B9
ADV7341_Y2
1A10
44
1B10
ADV7341_Y3
1A11
43
1B11
ADV7341_Y4
1A12
42
1B12
ADV7341_Y5
2A1
41
2B1
ADV7341_Y6
2A2
40
2B2
ADV7341_Y7
2A3
39
2B3
ADV7341_Y8
2A4
37
2B4
ADV7341_Y9
2A5
36
2B5
2A6
35
2B6
2A7
34
2B7
2A8
33
2B8
2A9
32
2B9
2A10
31
2B10
2A11
30
2B11
2A12
29
2B12
2A10
2A11
2A12
55
2OE
SN74CB3Q16211
TSSOP56
2OE
SN74CB3Q16211
TSSOP56
C17
0.1UF
0402
ANALOG
DEVICES
Title
16-Bit Mode
YCbCr 4:2:2
B
3
8-Bit Mode
YCbCr 4:2:2
3.3V
1OE
49
38
SN74CB3Q16211
TSSOP56
19
16_BIT_ADV7511
4
8
55
2OE
GND4
ADV7511_D34
PPID15
GND3
39
2B3
20
2A4
GND2
18
2A3
GND1
PPID14
31
2B10
ADV7341_C3
C1
0.1UF
0402
GND2
38
GND3
49
GND4
PPID3
4
53
1B2
GND1
PPID2
26
1A2
8
ADV7511_D22
3
32
2B9
2A9
GND4
PPID1
25
49
ADV7511_D21
2A8
ADV7341_C2
GND3
PPID2
52
1B3
2A7
54
1B1
1A1
GND2
53
1B2
4
1A3
2
38
3
1A2
PPID0
R29
10K
0402
19
PPID1
ADV7511_D20
GND1
54
1B1
8
3
VCC
2
1A1
PPID0
17
TP10
U12
3.3V
56
8_BIT_ADV7341
3.3V
U13
2
19
SN74CB3Q16211
TSSOP56
ADV7341_C2
1A2
1A9
GND1
55
2OE
24_BIT_ADV7511
8
2
54
1B1
1A1
17
ADV7511_D5
VCC
53
1B2
38
3
1A2
ADV7511_D4
19
PPID1
U11
54
1B1
17
VCC
2
1A1
GND1
1
PPID0
8
U10
17
VCC
TP9
Size
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
Video Modes
Board No.
Rev
A0252-2010
C
Date
20 Cotton Road
1.0
Sheet
3/6/12
D
4
of
8
A
ADV7511_AVDD
B
ADV7511_AVDD
C19
0.1UF
0402
ADV7511_PVDD
ADV7511_PLVDD
ADV7511_BGVDD
R18
10K
0402
L1
10UH
1008
ADV7511_PVDD
U17
R17
33
0402
4
VDD
1
OE
1
D
C
OUT
3
ADV7511_PLVDD
CEC_CLK
ADV7511_AVDD
C22
10UF
0805
GND
12MHZ 2
OSC015
1
ADV7511_33
ADV7511_DVDD
U14
79
PPICLK
R20
27K
0402
CLK
PPIFS1
98
HSYNC
PPIFS2
2
VSYNC
97
47
TP12 TP13 TP14 TP25
DVDD_33V
TP19
1
DVDD119
DVDD249
DVDD376
DVDD477
DVDD5
21
PVDD124
PVDD225
PVDD3
26
BGVDD
29
AVDD134
AVDD241
AVDD3
ADV7511_33
D8
DB3X314
DE
DIO_DB3X314
TXC-
TWI Address 0111 001x
x is the R/W bit. Read - 1, Write - 0
TXC+
95
D1
TX0-
94
D2
TX0+
TX1-
ADV7511_D5
91
D5
TX2-
ADV7511_D6
90
D6
43
TX2+
ADV7511_D7
89
D7
88
87
D8
CEC
D9
CEC_CLK
85
DDCSCL
D11
DDCSDA
83
D13
82
D14
HEAC-
81
D15
HEAC+
ADV7511_D16
80
D16
ADV7511_D17
78
D17
42
TXC+
CEC
TX0-
CEC_CLK
TX0+
TX1TX1+
5V
ADV7511_DVDD
TX2TX2+
48
R21
2.0K
0402
50
R22
2.0K
0402
R23
49.9
0402
2
R24
49.9
0402
C20
1UF
0402
73
ADV7511_D19
HPD
ADV7511_D21
71
D21
ADV7511_D22
70
D22
ADV7511_D23
69
D23
ADV7511_D24
68
D24
ADV7511_D25
67
D25
ADV7511_D26
66
D26
DSD0
ADV7511_D27
65
D27
DSD1
63
ADV7511_D29
D28
DSD2
D29
DSD3
ADV7511_D30
62
D30
DSD4/DST_ST
ADV7511_D31
61
D31
DSD5/DST_FL
ADV7511_D32
60
D32
DSD_CLK/DST_CLK
ADV7511_D33
59
D33
ADV7511_D34
58
D34
SPDIF
ADV7511_D35
57
D35
I2S0
I2S1
45
ADV7511_INT
INT
I2S2
38
PD
I2S3
MCLK
EI3_SCL
0
55
SCL
SCLK
56
SDA
LRCLK
LQFP100
ADV7511KSTZ
DDCSDA
51
HEAC-/HPD
52
30
R28
10K
0402
HEAC-/HPD
3
4
5
U22
6
3.3V
3
HEAC-/HPD
7
SN74LVC1G125
SOT23-5
8
LED1
YELLOW
LED001
9
C23
0.1UF
0402
10
12
13
14
15
SPORT0_D0
R19
430
0402
SPORT0_D1
SPORT1_D0
SPORT1_D1
11
16
17
SPORT0_CLK
SPORT0_FS
46
ANALOG
DEVICES
Close to U14 as possible and opposite pcb side
4
Title
Size
Date
C
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
ADV7511
Board No.
Rev
A0252-2010
C
B
HDMI Device Detected
R_EXT
R32
887
0603
A
R27
0
0402
28
18
20GND1
22GND2
23GND3
27GND4
31GND5
37GND6
44GND7
75GND8
99GND9
100GND10
GND11
SPDIF_OUT
R31
2.0K
0402
HEAC+
C21
1UF
0402
D19
ADV7511_D20
64
DDCSCL
54
D18
72
D20
ADV7511_D28
53
1
74
ADV7511_D18
EI3_SDA
40
TXC-
86
D10
84
D12
R13
0402
39
TX1+
ADV7511_D11
R30
4.7K
0402
36
92
D4
ADV7511_D10
ADV7511_33
35
ADV7511_D4
ADV7511_D9
3
33
93
D3
ADV7511_D8
2
96
D0
32
1.0
Sheet
3/6/12
D
5
of
8
A
B
D
C
ADV7341_PVDD
ADV7341_33
1
1
C38
2.2UF
0805
C39
2.2UF
0805
3.3V
ADV7341_DVDD
3
4
ADV7341_Y2
5
35
COMP2
45
COMP1
41
VAA
34
PVDD
1
56
VDD2
VDD_IO
2
VDD1
U2
10
TWI Address 0101 011x
x is the R/W bit. Read - 1, Write - 0
Y0
Y1
DAC1
Y2
DAC2
Y3
44
DAC1
DAC1
Y4
43
DAC2
DAC2
Y5
42
DAC3
DAC3
Y6
39
DAC4
DAC4
Y7
38
DAC5
DAC5
ADV7341_Y8
12
Y8
37
DAC6
ADV7341_Y9
13
Y9
ADV7341_Y3
6
ADV7341_Y4
7
ADV7341_Y5
8
ADV7341_Y6
9
ADV7341_Y7
51
ADV7341_S2
ADV7341_S3
ADV7341_S4
ADV7341_S5
ADV7341_S6
ADV7341_S7
53
54
55
58
59
60
C32
0.012UF
0402
DAC6
R35
169.0
0402
S0
52
S1
2
EXT_LF1
R48
75.0
0603
ADV7341_PVDD
R52
75.0
0603
R53
75.0
0603
C31
0.15UF
0603
33
2
S2
C34
0.012UF
0402
S3
S4
DAC3
Place as close to U2 as possible
and on same pcb side
Place close to U2
31
EXT_LF2
R36
169.0
0402
S5
S6
C33
0.15UF
0603
S7
ADV7341_S8
61
S8
ADV7341_S9
62
S9
R37
1.1K
0402
ADV7341_33
46
VREF
14
15
ADV7341_C2
ADV7341_C3
ADV7341_C4
ADV7341_C5
ADV7341_C6
ADV7341_C7
3
16
17
18
25
26
27
C0
C1
47
RSET1
C2
36
RSET2
SOT23D
C4
R33
4.12K
0402
C5
C6
ADV7341_C9
29
C9
ADV7341_33
R38
4.7K
0402
3
30
CLKIN_A
63
CLKIN_B
PPIFS1
PPIFS2
R34
510.0
0402
C7
28
C8
PPICLK
D7
AD1580BRTZ
C3
ADV7341_C8
TP15
C35
0.1UF
0402
22
19
ALSB
P_HSYNC
21
SCL
23
P_VSYNC
20
SDA
EI3_SCL
R26
0402
0
EI3_SDA
24
P_BLANK
49
S_VSYNC
LQFP64
ADV7341BSTZ
11
DGND1
57
DGND2
64
GND_IO
32
PGND
40
AGND
50
S_HSYNC
48
SFL
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
ADV7341
Board No.
Rev
A0252-2010
C
Date
20 Cotton Road
1.0
Sheet
3/6/12
D
6
of
8
A
B
D
C
3.3V
ADV7341_33
1
1
2
1
2
R43
10K
0402
ADV7341_33
2
DAC5
D1
BAT54S
3
D2
BAT54S
SOT23D
3
D3
BAT54S
SOT23D
3
C43
0.1UF
0402
J1
SOT23D
1
2
C42
0.01UF
0402
R44
300.0
0402
U24
1
VIN
VS+
2
GND
PD
3
SAG
VOUT
6
R42
75.0
0603
5
4
ADA4430
SC70_6
1
75 Ohm traces
R
1
4
Component
G
3
6
J2
ADV7341_33
CUI-STACK_MD-40SM
MINI-DIN
R46
10K
0402
ADV7341_33
CUI-STACK_RCJ-32265
RCA
R49-R51 should be very close to J3.
R50
0
0402
4
C
Place close to ADV7341
B
5
R49
0
0402
DAC6
C44
0.1UF
0402
R51
0
0402
C45
0.01UF
0402
R45
300.0
0402
U25
1
VIN
VS+
2
GND
PD
3
SAG
VOUT
6
R47
75.0
0603
5
4
ADA4430
SC70_6
J3
Terminators close to video filters
4
1
DAC3
2
DAC1
3
DAC2
13
PPIFS1
2
14
PPIFS2
9
15
12
1
GND12
GND25
GND36
GND47
GND5
3
Y
GND1
RED
5
GND2
GREEN
6
GND3
BLUE
7
GND4
HS
8
GND5
VS
10
GND6
VGA_5V
11
GND7
VGA_SCL
16
GND8
VGA_SDA
17
GND9
Place close to ADV7341
VGA
S-Video
2
EDAC_634-015-263-032
DSUB
DNP
ADV7341_33
5V
75 Ohm traces
100 Ohm diff pairs
(50 Ohms to GND)
J5
1
TX2+
2
TMDS_DATA2+
TMDS_SHIELD2
DAC4
3
TX2-
TMDS_DATA2-
4
TX1+
TMDS_DATA1+
5
TMDS_DATA0+
8
TMDS_SHIELD0
9
TX0-
TMDS_DATA0-
10
TXC+
TMDS_CLOCK+
11
3
3
SAG
VOUT
R41
75.0
0603
5
2
4
ADA4430
SC70_6
3
Composite
SDA
17
DDC/CEC_GND
18
DDCSDA
PD
Terminator close to video filter
SCL
16
DDCSCL
HDMI
HEC
15
CEC
2
GND
J6
RCA
CON012
6
Place close to ADV7341
CEC
14
HEAC-/HPD
VS+
1
TMDS_CLOCK-
13
HEAC+
R39
300.0
0402
U23
1
VIN
TMDS_CLK_SHIELD
12
TXC-
C41
0.01UF
0402
TMDS_DATA1-
7
TX0+
C40
0.1UF
0402
TMDS_SHIELD1
6
TX1-
R40
10K
0402
ADV7341_33
+5V
19
HOT_PLUG_DETECT
FCI_10029449-002TLF
HDMI
HEAC-/HPD
TXC-
TX1-
DDCSDA
TXC+
TX1+
DDCSCL
TX0-
TX2-
HEAC+
TX0+
TX2+
D9
10
OUT1
1
IN2
9
OUT2
2
IN3
7
OUT3
4
6
OUT4
5
8
GND2
3
2
4
5
IN4
4
3
GND1
D11
D10
IN1
1
RCLAMP0524
DIO_RCLAMP0524
IN1
10
OUT1
1
IN2
9
OUT2
2
IN3
7
OUT3
4
IN4
6
OUT4
5
GND1
8
GND2
3
RCLAMP0524
DIO_RCLAMP0524
10
IN1
OUT1
9
IN2
OUT2
ANALOG
DEVICES
7
IN3
OUT3
6
IN4
OUT4
GND1
8
GND2
RCLAMP0524
DIO_RCLAMP0524
R55
VARISTOR
0603
Title
Size
A
Date
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
Video Connectors
Board No.
Rev
A0252-2010
C
CEC
20 Cotton Road
1.0
Sheet
3/6/12
D
7
of
8
A
B
D
C
L2
10UH
1008
FER1
1
IN
3.3V
ADV7511_DVDD
3
OUT
2
GND
C49
10UF
0805
NFE61PT472
FIL_NFE61PT
TP24
TP23
TP20
TP21
C50
0.01UF
0402
C51
0.1UF
0402
C52
0.01UF
0402
C53
0.1UF
0402
C55
0.01UF
0402
C54
0.1UF
0402
C56
0.01UF
0402
C57
0.1UF
0402
TP22
LED2
GREEN
LED001
1
L3
10UH
1008
FER2
R54
430
0402
1
IN
1
ADV7511_PVDD
3
OUT
2
GND
C58
10UF
0805
NFE61PT472
FIL_NFE61PT
L4
10UH
1008
FER3
1
IN
C59
0.01UF
0402
C60
0.1UF
0402
C65
0.01UF
0402
C64
0.1UF
0402
ADV7511_BGVDD
3
OUT
2
GND
C66
10UF
0805
NFE61PT472
FIL_NFE61PT
L5
10UH
1008
FER4
2
1
IN
ADV7511_AVDD
2
3
OUT
2
GND
C68
10UF
0805
NFE61PT472
FIL_NFE61PT
C69
0.01UF
0402
C70
0.1UF
0402
C71
0.01UF
0402
C72
0.1UF
0402
C83
0.01UF
0402
C82
0.1UF
0402
C81
0.01UF
0402
C80
0.1UF
0402
C74
0.01UF
0402
C73
0.1UF
0402
1.8V @ 1A
L6
10UH
1008
FER5
1
TP3
5V
TP1
IN
1.8V
ADV7341_DVDD
3
OUT
2
GND
1
EN
3
5
OUT1
IN1
6
OUT2
IN2
7
SENSE
SS
2
GND
4
8
C84
10UF
0805
NFE61PT472
FIL_NFE61PT
VR2
C46
4.7UF
0603
ADP1706-1.8V
LFCSP8
L7
10UH
1008
FER6
3
C47
4.7UF
0603
VIN
USB_VCC
C48
0.01UF
0402
1
IN
3
3
OUT
2
GND
PWR_IN
C85
10UF
0805
NFE61PT472
FIL_NFE61PT
D4
MBR130LSFT1G
SOD-123FL
ADV7341_PVDD
C86
0.01UF
0402
C87
0.1UF
0402
C91
0.01UF
0402
C90
0.1UF
0402
F1
1A
1206
TP2
D5
MBR130LSFT1G
SOD-123FL
3.3V
VR1
1
5
OUT1
3
6
OUT2
4
7
SENSE
EN
IN1
D6
MBR130LSFT1G
SOD-123FL
IN2
8
SS
L8
10UH
1008
FER7
2
GND
1
IN
ADV7511_33
3
OUT
2
GND
C67
4.7UF
0603
C92
10UF
0805
NFE61PT472
FIL_NFE61PT
ADP1706-3.3V
LFCSP8
P1
3
C63
4.7UF
0603
2
C75
0.01UF
0402
1
5V_POWER
CON027
L9
10UH
1008
FER8
1
IN
4
ANALOG
DEVICES
ADV7341_33
3
OUT
2
GND
NFE61PT472
FIL_NFE61PT
C95
10UF
0805
3.3V @ 1A
C94
0.01UF
0402
C93
0.1UF
0402
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Video Encoder EI3 Extender Board
Power
Board No.
Rev
A0252-2010
C
Date
20 Cotton Road
1.0
Sheet
3/6/12
D
8
of
8
I
INDEX
Numerics
27MHZ_CLK_EN signal, 2-10
74MHZ_CLK_EN signal, 2-10
A
ADV7341 video encoder, ix
ADV7511_INT_GPIOx signal, 2-10
ADV7511 video encoder, ix
architecture, of Video Encoder EI3 Extender
Board, 2-2
B
bill of materials, A-1
block diagram of Video Encoder EI3 Extender
Board, 2-2
board design database, 1-7
board schematic (Video Encoder EI3 Extender
Board), B-1
bus switch, 2-5
example, 2-5
composite (J6), 2-14
expansion III (EI3) (J4), 2-12
HDMI (J5), 2-13
power (P1), 2-14
single RCA jack, 2-14
S-video DIN (J2), 2-12
triple RCA jack (J4), 2-13
contents, of this extender board package, 1-2
D
design reference info, 1-7
E
EngineerZone, xiv
expansion III (EI3) connectors (J4), 2-12
extender board block diagram, 2-2
F
FET switches, 2-3
example, 2-4
C
H
component connector (J14), 2-13
composite connector (J6), 2-14
configuration, of Video Encoder EI3 Extender
Board, 1-2
connector locations, 2-11
connectors
120-pin 0.6 mm pitch, 2-12
component (J14), 2-13
HDMI connector (J5), 2-13
HDMI Detect LED (LED1), 2-15
I
installation, of Video Encoder EI3 Extender
Board, 1-2
interfaces, x
Video Encoder EI3 Extender Board Manual
I-1
Index
L
27MHZ_CLK_EN, 2-10
74MHZ_CLK_EN, 2-10
ADV7511_INT_GPIOx, 2-10
SPORT_ENABLE, 2-10
video encoder mode select, 2-10
SoftConfig, 2-3
overview, 2-3
programming switches, 2-7
software-controlled switches (SoftConfig),
2-3
SPORT_ENABLE signal, 2-10
supported products, xiii
S-video connector (J2), 2-12
switches
programming SoftConfig, 2-7
system architecture, 2-2
LEDs, 2-15
HDMI Detect (LED1), 2-15
power (LED2), 2-15
M
mechanical switch, 2-4, 2-6
N
notation conventions, xv
P
package contents, 1-2
power connector (P1), 2-14
power LED (LED2), 2-15
product information, xiii
product overview, ix
T
technical support, xii
R
V
related documents, xv
related processor publications, xv
video connectors, x
Video Encoder EI3 Extender Board
interfaces, x
video encoder mode select, 2-10
video interface,
ADV7341, x
ADV7511, x
S
schematic, of Video Encoder EI3 Extender
Board, B-1
signals
I-2
Video Encoder EI3 Extender Board Manual