Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC639ST89 / 639ST89E
v03.0810
Typical Applications
Features
The HMC639ST89(E) is ideal for:
Low Noise Figure: 2.3 dB
• Cellular / PCS / 3G
High P1dB Output Power: +22 dBm
• WiMAX, WiBro, & Fixed Wireless
High Output IP3: +38 dBm
• CATV & Cable Modem
Gain: 13 dB
9
• Microwave Radio
50 Ohm I/O’s - No External Matching
• IF and RF Sections
Industry Standard SOT89 Package
AMPLIFIERS - LINEAR & POWER - SMT
HIGH IP3, LOW NOISE
AMPLIFIER, 0.2 - 4.0 GHz
Functional Diagram
General Description
The HMC639ST89(E) is a GaAs pHEMT, High
Linearity, Low Noise, Wideband Gain Block Amplifier
covering 0.2 to 4.0 GHz. Packaged in an industry
standard SOT89, the amplifier can be used as either
a cascadable 50 Ohm gain stage, a PA Pre-Driver,
a Low Noise Amplifier, or a Gain Block with up to
+22 dBm output power. This versatile Gain Block
Amplifier is powered from a single +5V supply and
requires no external matching components. The
internally matched topology permits this amplifier to
be readily ported between virtually any printed circuit
board material, regardless of its dielectric constant,
thickness, or composition.
Electrical Specifications, Vs= 5V, TA = +25° C
Parameter
Min
Frequency Range
Gain
Typ.
Max
Min.
0.7 - 2.2
10
Gain Variation Over Temperature
13
0.01
Input Return Loss
Typ.
Max.
0.2 - 4.0
6
0.02
12
GHz
10
0.01
Units
dB
0.02
12
dB/ °C
dB
Output Return Loss
12
14
dB
Reverse Isolation
20
20
dBm
Output Power for 1 dB Compression (P1dB)
19
21
20
22
dB
Output Third Order Intercept (IP3)
35
38
35
38
dBm
90
110
90
110
Noise Figure
Supply Current (Icq)
2.3
2.5
120
dB
120
mA
Note: Data taken with broadband bias tee on device output.
9-1
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC639ST89 / 639ST89E
v03.0810
HIGH IP3, LOW NOISE
AMPLIFIER, 0.2 - 4.0 GHz
Gain vs. Temperature
20
16
15
14
10
12
S21
S11
S22
0
-5
10
8
6
-10
4
-15
2
-20
0
0
1
2
3
4
5
6
0
1
FREQUENCY (GHz)
3
4
5
Output Return Loss vs. Temperature
0
0
+25C
+85C
-40C
-5
RETURN LOSS (dB)
RETURN LOSS (dB)
2
FREQUENCY (GHz)
Input Return Loss vs. Temperature
-10
-15
-20
+25C
+85C
-40C
-5
-10
-15
-20
0
1
2
3
4
5
0
1
FREQUENCY (GHz)
3
4
5
4
5
Noise Figure vs. Temperature
10
-5
8
NOISE FIGURE (dB)
0
+25C
+85C
-40C
-10
2
FREQUENCY (GHz)
Reverse Isolation vs. Temperature
REVERSE ISOLATION (dB)
9
+25C
+85C
-40C
-15
-20
+25C
+85C
-40C
6
AMPLIFIERS - LINEAR & POWER - SMT
5
GAIN (dB)
RESPONSE (dB)
Broadband Gain & Return Loss
4
2
-25
0
0
1
2
3
FREQUENCY (GHz)
4
5
0
1
2
3
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
9-2
HMC639ST89 / 639ST89E
v03.0810
HIGH IP3, LOW NOISE
AMPLIFIER, 0.2 - 4.0 GHz
Psat vs. Temperature
30
30
25
25
20
20
Psat (dBm)
9
P1dB (dBm)
P1dB vs. Temperature
15
+25C
+85C
-40C
10
10
5
0
0
0
1
2
3
4
0
1
2
FREQUENCY (GHz)
4
Power Compression @ 2200 MHz
32
Pout (dBm), GAIN (dB), PAE (%)
32
Pout (dBm), GAIN (dB), PAE (%)
3
FREQUENCY (GHz)
Power Compression @ 850 MHz
Pout
Gain
PAE
24
16
8
0
-8
-20
-12
-4
4
12
16
8
0
-8
-20
20
Pout
Gain
PAE
24
-12
-4
INPUT POWER (dBm)
35
25
20
1
2
FREQUENCY (GHz)
20
3
4
160
160
140
120
Gain
P1dB
Psat
IP3
140
120
100
100
80
Is
80
60
60
40
40
20
20
0
0
4.5
4.75
5
5.25
5.5
Vs (V)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
Is (mA)
0 dBm
5 dBm
10 dBm
GAIN (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
40
0
12
Gain, Power, Output IP3 & Supply Current
vs. Supply Voltage @ 850 MHz
45
30
4
INPUT POWER (dBm)
Output IP3 vs. Output Tone Power
IP3 (dBm)
AMPLIFIERS - LINEAR & POWER - SMT
5
9-3
+25C
+85C
-40C
15
HMC639ST89 / 639ST89E
v03.0810
HIGH IP3, LOW NOISE
AMPLIFIER, 0.2 - 4.0 GHz
Absolute Maximum Ratings
+5.5 Volts
RF Input Power (RFIN)(Vcc = +5 Vdc)
+15 dBm
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 13.3 mW/°C above 85 °C)
0.86 W
Thermal Resistance
(Channel to lead)
75.6 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ESD Sensitivity (HBM)
Class 1A
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
9
Outline Drawing
NOTES:
1. PACKAGE BODY MATERIAL:
MOLDING COMPOUND MP-180S OR EQUIVALENT.
2. LEAD MATERIAL: Cu w/ Ag SPOT PLATING.
3. LEAD PLATING: 100% MATTE TIN.
4. DIMENSIONS ARE IN INCHES [MILLIMETERS]
5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
AMPLIFIERS - LINEAR & POWER - SMT
Collector Bias Voltage (Vcc)
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC639ST89
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC639ST89E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
H639
XXXX
H639
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
9-4
HMC639ST89 / 639ST89E
v03.0810
HIGH IP3, LOW NOISE
AMPLIFIER, 0.2 - 4.0 GHz
Pin Descriptions
Pin Number
Function
Description
1
RFIN
This pin is DC coupled. An off-chip
DC blocking capacitor is required.
3
RFOUT
RF Output and DC BIAS for the amplifier.
See Application Circuit for off-chip components.
2, 4
GND
These pins and package bottom must
be connected to RF/DC ground.
AMPLIFIERS - LINEAR & POWER - SMT
9
9-5
Interface Schematic
Application Circuit
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC639ST89 / 639ST89E
v03.0810
HIGH IP3, LOW NOISE
AMPLIFIER, 0.2 - 4.0 GHz
Evaluation PCB
List of Materials for Evaluation PCB 119394
Item
Description
J1 - J2
PCB Mount SMA Connector
J3 - J4
DC Pin
C1 - C3
100 pF Capacitor, 0402 Pkg.
C4
1000 pF Capacitor, 0603 Pkg.
C5
2.2 µF Capacitor, Tantalum
L1
47 nH Inductor, 0603 Pkg.
U1
HMC639ST89(E)
PCB [2]
119392 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[1]
The circuit board used in the application should
use RF circuit design techniques. Signal lines
should have 50 Ohm impedance while the package
ground leads and package bottom should be
connected directly to the ground plane similar to
that shown. A sufficient number of via holes should
be used to connect the top and bottom ground
planes. The evaluation board should be mounted
to an appropriate heat sink. The evaluation circuit
board shown is available from Hittite upon request.
AMPLIFIERS - LINEAR & POWER - SMT
9
[2] Circuit Board Material: FR4
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
9-6