GSM-R Cab Radio Software Versions NR3.X>3.5 (Driver)
11
1
12
1
13
2
14
3
No
1
2
3
4
5
Description
Railway Emergency
Group call
Urgent
call to Signaller
Acknowledge
Brightness (+/-)
Test
July 2015
4
5
No
6
7
8
9
10
6
7
Description
Menu
Volume/Menu navigation
Accept
Keypad
Cancel
Applicable to Cab Radio software versions NR3.X>3.5
Issue 0.5
8
No
11
12
13
14
9
10
Description
Reg/De-reg
Standing at Signal
TOC Phonebook
Call Signaller
Page 1
Giving a Non Verbal Acknowledgement to a Safety Broadcast
3.5
Receiving a
Safety
Broadcast
Only modified radios displaying this sticker
will allow the driver to
acknowledge a safety broadcast. (software version 3.5)
 You must wait for the broadcast to finish ‘End of Safety broadcast’
and the display is no longer showing ‘connected’.
 Only then, when you are confident you have understood the
message, press the Acknowledge button
and act in accordance
with the instructions given by the broadcast.
 Only when your acknowledgement is received will the signaller
clear the protecting signal / block marker.
 When the Safety broadcast has been received and acknowledged
you can continue to obey all signals and apply the appropriate rule
over the affected section of line.
July 2015
Applicable to Cab Radio software versions NR3.X>3.5
Issue 0.5
Page 2
Registration Tips
Keeping
Registration
To keep registration when leaving the cab
Remove Master Key
The message Press tick to retain appears on the display
Press
within 10 seconds
The registration is retained for 30 minutes
PreRegistration
To prepare the radio for registration during the journey
Press
Enter Train Reporting Number (headcode) (4 alpha numeric digits)
Enter Company Wild Card Code (99X) (instead of signal number)
Press
(Note reminder PR NANN 99X displayed on screen)
----------------------------------------------------------------------------------------------When you pass the start of GSM-R coverage boards
Press
and radio will register
To register when network coverage has been lost
Pending
Registration
July 2015
Enter Train Reporting Number (headcode) (4 alpha numeric digits) +
Company Wild Card Code (99X) (instead of signal number)
----------------------------------------------------------------------------------------------When you regain network coverage, the radio automatically registers
Applicable to Cab Radio software versions NR3.X>3.5
Issue 0.5
Page 3
Failures
Registration
Failure
messages
Radio Failure
Message
Registration Failed: Check code and retry registration.
If still unsuccessful: Contact signaller for any known problems. After
this, one further attempt can be made using your company wild card
code ‘99X’. If this fails it should be reported back to the signaller using
the GSM-R radio.
If still unsuccessful: If all registration attempts are unsuccessful, trains
can enter service unregistered provided the display is showing GSM-R
GB.
Radio Failure : Service Affecting Failure - Report to signaller
Warning : Non-service Affecting Failure - Report to Train Operator’s
Control
Useful Menu shortcuts
Restore Default
Press
Settings
Access NR
Press
Phonebook
When the cab radio is not registered
Contacting the
Driver to contact signaller by phonebook or dial the signaller’s number
Signaller
on the signal box phone number plate using the keypad. This could be
the eight figure number or the short code 12NN number depending on
area. (DO NOT USE
July 2015
]1[
button or
Applicable to Cab Radio software versions NR3.X>3.5
SG
Issue 0.5
button)
Page 4
Driver to Driver Communication Using the Multiparty Call Function
Setup
Lead Driver
Lead Driver establishes Journey Code (5 digits) and the 99X special Location
Code with signaller
Enter agreed Registration Code (5 digits + 99X) through the menu
Press
Setup
Driver 2
Select 1 Lead Driver from the list of options
-----------------------------------------------------------------------------------------------Driver 2 registers through the menu
Press
Enter the same Registration Code (using same 8 digits) as Lead Driver
Select Driver 2 from the list of options
Press
-----------------------------------------------------------------------------------------------To set up a call between drivers (Lead Driver to initiate the call)
Calling each
other
Hold/Swap
Call
July 2015
Press
Press
Build Multiparty
Radio finds all other radios with the same 8 digit registration code.
To put call on Hold
To Swap between calls
Press
Press
Applicable to Cab Radio software versions NR3.X>3.5
Issue 0.5
Page 5