Data Sheet 1772-4C
JD Series
Filter Housings
Polypropylene Single Cartridge Housing
• Constructed from polypropylene with no fillers,
colorants or lubricants
• Economical alternative to fluoropolymer, stainless steel
or other high purity vessels
• Housing designed to accept SOE filter cartridges with
222 O-ring sealing
• Excellent chemical compatibility for use with
semiconductor grade chemicals, CMP slurry, magnetic
coatings, electronic etching solutions, DI and reagent
grade water
• Accommodates standard 50.8 cm (20 in) Pall M3
(Code 3) style filter cartridges
Housing Specifications
Maximum operating pressure1
6.9 bar @ 38°C (100 psig @ 100°F)
Material of construction
Polypropylene – no fillers, colorants or lubricants
Connections
Inlet/outlet:
Vent/gauge:
Drain:
⁄4" FNPT
⁄4" FNPT
1
⁄4" FNPT
3
1
Shell O-rings
Fluoroelastomer (standard), nitrile, silicone elastomer
Replacement cap plug kit
For vents/drains – includes one plug and one O-ring
(Part # T11039030)
This housing is not recommended for compressed air or gas service. It is suitable
for use with fully compatible* liquids only. This housing is not recommended for
acid service at the pressure shown. Please contact Pall for detailed compatibility
information.
* which do not soften, swell or adversely affect the product or its materials of
construction
1
Maximum operating pressure ratings are vessel ratings only. Safe operating
temperature and pressure will depend on filter cartridge and gasket/O-ring
used. For inquiries on compatibility, contact the factory or your Pall distributor.
NOTE:
Use of this product in a manner other than in accordance with Pall’s
current recommendations may lead to injury or loss. Pall cannot
accept liability for such injury or loss.
Dimensional Data (nominal)
Dimensions
Model
JD20
Weight
A
B
50.65 cm (19.94 in)
13.03 cm (5.13 in)
1.93 kg (4.25 lb)
Top view
B
Side view
2.25"
(5.7 cm)
Vent plug
Vent plug
IN
OUT
2.375"
(6 cm)
A
Mounting
bosses (4)
Optional mounting brackets
3"
(7.6 cm)
4"
(10.2 cm)
1"
(2.54 cm)
3.75"
(9.5 cm)
5.5"
(13.97 cm)
Drain plug
5.42" inner
(13.8 cm)
3.81"
(9.7 cm)
2.38"
(6 cm)
7.03"
(17.9 cm)
2.25"
(5.7 cm)
Part #11018031
Part #11018030
Typical Flow vs. Differential Pressure2
Flow rate (lpm), water at 20˚C
Pall Part Number = JD20 – 3/4 1
0
Code
O-ring Materials
Blank
Fluoroelastomer
N
Nitrile
S
Silicone
Differential pressure (psid)
Table 1
8
16
24
32
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.05
0.4
0.3
0.2
0.1
0
0.01
0.03
0
1
2
3
4
5
6
7
8
9
Differential pressure (bard)
Ordering Information
10
Flow rate (gpm), water at 68˚F
Unit conversion: 1 bar = 100 kPa
2
25 Harbor Park Drive
Port Washington, NY 11050
+1 516 484 3600
telephone
+1 800 289 7255
toll free US
Portsmouth - UK
+44 (0)23 9230 3303 telephone
+44 (0)23 9230 2507 fax
processuk@pall.com
Flow/pressure drop characteristics refer to the empty housing only. For liquids
other than water, multiply differential pressure by the specific gravity of the fluid.
Visit us on the Web at www.pall.com
Pall Corporation has offices and plants throughout the world. For Pall representatives
in your area, please go to www.pall.com/contact
Because of technological developments related to the products, systems, and/or
services described herein, the data and procedures are subject to change without
notice. Please consult your Pall representative or visit www.pall.com to verify that
this information remains valid.
© Copyright 2004, 2010, Pall Corporation. Pall and
are trademarks of Pall Corporation.
® indicates a trademark registered in the USA. Filtration. Separation. Solution.SM is a service
mark of Pall Corporation.
1772-4C
Produced in the USA
December 2010