Vicinity Map Columbine Hall - Third Floor Classrooms AV Upgrade

advertisement
Columbine Hall - Third Floor
Classrooms AV Upgrade
1420 Austin Bluffs Parkway, Colorado
Springs, CO 80918
Vicinity Map
ABBREVIATIONS
INSTALL
COMMON WORK
CONDUIT SLEEVES
EC
EC
1
PENETRATION
GC
GC
5,7
HANGER SUPPORTS FOR CONDUITS
EC
EC
1
HANGER SUPPORTS FOR CABLE SUPPORTS
TC
TC
2
WIDE BASE CABLE SUPPORTS (J-HOOKS)
TC
TC
2
STRAPS/SLINGS
TC
TC
2
ELECTRICAL FOR COMMUNICATIONS SYSTEMS
CONDUIT, FITTINGS, PULL STRINGS
EC
EC
1
JUNCTION BOXES
EC
EC
1
DEVICE BOXES
EC
EC
1
PULL BOXES
EC
EC
1
TABLE-TOP INTERFACE (ROUGH IN)
AVC
AVC
4
TABLE-TOP INTERFACE (DEVICE)
AVC
AVC
TC
TC
TELECOMMUNICATIONS (COMMUNICATIONS CABLING SYSTEM)
AUDIOVISUAL SYSTEM(S)
A.
LOUDSPEAKERS
AVC
AVC
HANGER WIRE SUPPORTS FOR LOUDSPEAKERS WITHIN LAYING CEILINGS
AVC
AVC
MICROPHONES
AVC
AVC
EQUIPMENT RACKS
AVC
AVC
ANTENNA
AVC
AVC
PROJECTION SCREEN
AVC
AVC
INTERFACE PLATES
AVC
AVC
PROJECTORS
AVC
AVC
CAMERAS
AVC
AVC
PODIUM
AVC
AVC
VOLUME CONTROL
AVC
AVC
CONTROL PANEL
AVC
AVC
SCREEN SWITCH
AVC
AVC
STRUCTURAL SUPPORTS FOR AV EQUIPMENT
GC
GC
9
GENERAL NOTES
COMPONENTS, ENTITY, AND FURNISH AND INSTALL RESPONSIBILITIES INDICATED ARE RECOMMENDATIONS ONLY AND PROVIDED AS
A COURTESY TO CONTRACTOR.
B.
SOME COMPONENTS AND ASSOCIATED FURNISH AND INSTALL RESPONSIBILITIES MAY NOT BE INDICATED ON THIS MATRIX.
C.
THE DETAIL FURNISH / INSTALL CALLOUT ANNOTATION PROVIDES SPECIFIC RECOMMENDATIONS THAT SUPERSEDE GENERAL
RECOMMENDATIONS FOUND IN THE TECHNOLOGY RESPONSIBILITY MATRIX.
D.
EQUIPMENT SCHEDULES MAY CONTAIN ADDITIONAL FURNISH OR INSTALL RESPONSIBILITY RECOMMENDATIONS. THESE SUPERSEDE
RECOMMENDATIONS FOUND IN DETAIL ANNOTATIONS AND THE TECHNOLOGY RESPONSIBILITY MATRIX.
E.
CONTRACTOR IS RESPONSIBLE FOR FINAL DETERMINATION OF ALL COMPONENTS AND ASSOCIATED FURNISH AND INSTALL
RESPONSIBILITIES REQUIRED FOR PROVISION OF COMPLETE TECHNOLOGY SYSTEMS READY FOR OWNER'S USE. DETERMINATION
OF SUCH SHALL OCCUR PRIOR TO BID.
F.
DETERMINATION AND EXECUTION OF ALL NECESSARY COMPONENTS AND ASSOCIATED FURNISH AND INSTALL RESPONSIBILITIES
SHALL CONFORM TO PROJECT SCHEDULE.
G.
CABLING FOR COMPONENTS SHALL BE PROVIDED BY ENTITY INSTALLING COMPONENT UNLESS OTHERWISE INDICATED.
H.
EACH TRADE SHALL COORDINATE ROUGH-IN REQUIREMENTS (INCLUDING SLEEVES) WITH ELECTRICAL CONTRACTOR PRIOR TO
ROUGH-IN.
I.
DEVICES AND HORIZONTAL CABLING OF DEVICES (INCLUDING CABLE TERMINATIONS) WITHIN ASSEMBLIES (FLOOR BOXES,
POKE-THROUGHS, TABLE TOP INTERFACES, WALL BOXES, FURNITURE FEEDS, UTILITY POLES, SURFACE RACEWAYS, ETC.) SHALL BE
BY RESPECTIVE TRADES.
1.
2.
MATRIX NOTES
EACH RESPECTIVE TRADE SHALL COORDINATE EXTENT OF WORK WITH ELECTRICAL CONTRACTOR PRIOR TO ROUGH IN.
EACH TRADE SHALL COORDINATE PROVISION OF THIS COMPONENT WITH TELECOMMUNICATIONS CONTRACTOR.
TELECOMMUNICATIONS CONTRACTOR SHALL PROVIDE THIS COMPONENT UNLESS DETERMINED OTHERWISE IN CONJUNCTION WITH
TELECOMMUNICATIONS CONTRACTOR.
4.
FURNISHING CONTRACTOR TO PROVIDE ROUGH IN DIMENSIONS / TEMPLATE AND DESIRED LOCATION FOR TABLE TOP INTERFACE.
INSTALLING CONTRACTOR SHALL CUT-OUT SURFACE OF TABLE, IDENTIFYING AND COORDINATING ANY POTENTIAL CONFLICTS WITH
DESIRED LOCATION PRIOR TO PERFORMING ANY WORK.
5.
EACH TRADE SHALL COORDINATE PROVISION OF THIS COMPONENT WITH GENERAL CONTRACTOR. GENERAL CONTRACTOR SHALL
PROVIDE THIS COMPONENT UNLESS DETERMINED OTHERWISE IN CONJUNCTION WITH GENERAL CONTRACTOR.
7.
ELECTRICAL CONTRACTOR SHALL COORDINATE EXTENT OF WORK WITH GENERAL CONTRACTOR.
9.
AUDIOVISUAL CONTRACTOR SHALL COORDINATE EXTENT OF WORK WITH GENERAL CONTRACTOR.
ABBREV.
DEFINITION
ABBREV.
DEFINITION
AC
ACEG
ACLGS
ACP
ACS
ACT
AFF
AHJ
AO
AOC
APC
APP
APPROX
AR
ARCH
ATEL
AV
AVC
AWG
BAS
BB
BC
BEP
BI
BLDG
BO
C
CAB
CAN
CAT3
CAT5E
CAT6
CAT6A
CATV
CC
CCTV
CER
CLG
CNL
CO
COAX
COM
COMM
CON
CPU
CPV
CR
CT
CV
DB
(D)
DD
DEA
DGCB
DIA
DM
DP
DPDT
DPS
DS
DVI
DVR
DWG
(E)
EB
EC
ECL
ECP
EF
EIB
EL
ELEC
ELM
ELR
ELV
EMT
ENCL
EQPMT
ER
ES
ESO
EXIST
(F)
FAC
FACP
FB
FD
FL
FLEX
FPA
FPD
FS
FSD
G
GC
HB
HC
HD
HDBT
HDMI
HO
ID
IDS
IF
IG
IMC
IP
IR
ISP
IVW
IWC
KIT
LAB
LC
LL
LM
LPS
LR
MAG
MECH
MED
MFR
MIC
MIN
ABOVE COUNTER
ALTERNATING CURRENT ELECTRICAL GROUND
ACCESSIBLE CEILING SPACE
ACCESS CONTROL PANEL
ACCESS CONTROL SYSTEM
ACOUSTIC CEILING TILE
ABOVE FINISHED FLOOR
AUTHORITY HAVING JURISDICTION
AUTOMATIC OPERATOR
AUTOMATIC OPENER CONTROLLER
ANGLE POLISHED CONNECTOR
AUDIO PATCH PANEL
APPROXIMATELY
AUXILIARY RELAY
ARCHITECT
ADMINISTRATIVE TELEPHONE
AUDIOVISUAL
AUDIOVISUAL CONTRACTOR
AMERICAN WIRE GAUGE
BUILDING AUTOMATION SYSTEM
BACKBONE
BARE COPPER
BUILDING ENTRANCE PROTECTOR
BIOMETRIC INTERFACE
BUILDING
BY OTHERS
CONDUIT
CABINET
CONTROLLED AREA NETWORK
CATEGORY 3 COPPER CABLE
CATEGORY 5E COPPER CABLE
CATEGORY 6 COPPER CABLE
CATEGORY 6 AUGMENTED COPPER CABLE
CABLE TELEVISION
CONTACT CLOSURE
CLOSED CIRCUIT TELEVISION
CYLINDER ELECTRIC RETRACTION
CEILING
COULD NOT LOCATE
CONDUIT ONLY (NO CABLE)
COAX CABLE
COMMON
COMMUNICATION
CONDUCTOR
COMPUTER PROCESSING UNIT
COMPONENT VIDEO
CARD READER
COUNT
COMPOSITE VIDEO
DIRECT BURIAL
DEMOLISH
DEAD
DELAYED EGRESS ALARM
DATA-GRADE COPPER BACKBONE
DIAMETER
DIGITAL MULTIMEDIA (SIGNAL)
DISPLAYPORT
DOUBLE POLE DOUBLE THROW
DOOR POSITION SWITCH
DIGITAL SIGNAGE
DIGITAL VIDEO INTERFACE
DIGITAL VIDEO RECORDER
DRAWING
EXISTING TO REMAIN
EXIT BUTTON
ELECTRICAL CONTRACTOR
ELECTRIC CYLINDER LOCK
ELEVATOR CONTROL PANEL
ENTRANCE FACILITY (DEMARC)
EMERGENCY INFORMATION BOARD
ELECTRIC LATCH
ELECTRICAL
ELECTRIC LATCH WITH LATCH MONITOR SWITCH
ELECTRICAL LATCH RETRACTION
ELEVATOR
ELECTRICAL METALLIC TUBING
ENCLOSURE
EQUIPMENT
EQUIPMENT ROOM
ELECTRIC STRIKE
ELECTRICAL SOLENOID
EXISTING
FUTURE
FIRE ALARM CONTRACTOR
FIRE ALARM CONTROL PANEL
FIBER BACKBONE, FLOOR BOX
FLOOR DISTRIBUTOR
FLUSH
FLEXIBLE CONDUIT
FLOOR PENETRATION ASSEMBLY
FLAT PANEL DISPLAY
FURNITURE SUPPLIER
FIRE STOP DEVICE
GROUND
GENERAL CONTRACTOR
HANDICAP BUTTON
HORIZONTAL CABLE
HIGH DEFINITION
HDBASET (AV SIGNALS OVER TP)
HIGH DEFINITION MULTIMEDIA INTERFACE
HOLD OPEN
INSIDE DIAMETER OR IDENTIFIER
INTRUSION DETECTION SYSTEM
INTERFACE PLATE
ISOLATED GROUND
INTERMEDIATE METAL CONDUIT
INTERNET PROTOCOL
INFRARED
INSIDE PLANT
IN VARIANCE WITH
IN-BUILDING WIRELESS CONTRACTOR
KITCHEN EQUIPMENT
LABORATORY EQUIPMENT
LOW VOLTAGE/SPECIALITY CONTRACTOR
LINE LEVEL LEFT CHANNEL AUDIO
LINE LEVEL MONO AUDIO
LOCK POWER SUPPLY
LINE LEVEL RIGHT CHANNEL AUDIO
MAGNETIC LOCK
MECHANICAL
MEDICAL EQUIPMENT
MANUFACTURER
MICROPHONE (CONNECTION)
MINIMUM
ML
MM
MREX
MS
(N)
(NL)
NA
NACLGS
NC
NEC
NO
NS
NTS
NVR
O
OB
OC
OD
OFCI
OFOI
OHM
OPE
OR
ORI
OSP
OXY
PA
PDS
POE
PP
PR
PRJ
PS
PWR
(RL)
(RE)
R
REV
REX
RF
RFG
RI
RM
RMC
RNC
RS-232
S
SATV
SC
SCC
SCHED
SCNS
SCP
SCPP
SCPS
SH
SM
SMR
SMT
SN
SP
SPEC
SPKR
SPR
SR
SRR
STP
SUS
SV
TB
TBB
TBD
TC
TCP
TEL
TGB
TMGB
TP
TR
TYP
U
UGND
UON
UPP
UPS
USB
UTP
VB
VE
VGA
VGA+A
VGCB
VLAN
VMS
VOIP
VSS
VTC
VW
W
WM
WP
WAP
MONITORED LATCH
MULTIMODE FIBER OPTIC CABLE
MOTION REQUEST TO EXIT
MONITORED STRIKE
NEW
NEW LOCATION
NOT APPLICABLE
NON ACCESSIBLE CEILING SPACE
NORMALLY CLOSED CONTACT
NATIONAL ELECTRIC CODE
NORMALLY OPEN CONTACT
NETWORK SWITCH
NOT TO SCALE
NETWORK VIDEO RECORDER
OWNER
OVERRIDE BUTTON
ON CENTER
OUTSIDE DIAMETER
OWNER FURNISHED, CONTRACTOR INSTALLED
OWNER FURNISHED, OWNER INSTALLED
RESISTIVE NETWORK
OWNER PROVIDED EQUIPMENT
OPERATING ROOM
OPERATING ROOM INTEGRATION
OUTSIDE PLANT
OXYGEN
PUBLIC ADDRESS
PROTECTIVE DISTRIBUTION SYSTEM
POWER OVER ETHERNET
PATCH PANEL(S)
PAIR
PROJECTOR
POWER SUPPLY
POWER
REMOVE AND RELOCATE
REMOVE
RISER
REVISION
REQUEST TO EXIT SWITCH
RADIO FREQUENCY
RAISED FLOOR GROMMET
READER INTERFACE
ROOM
RIGID METALLIC CONDUIT
RIGID NONMETALLIC CONDUIT
TWO WAY SERIAL DATA STREAM
STATION
SATELLITE TELEVISION
SECURITY CONTRACTOR
SECURITY CAMERA
SCHEDULE
SECURITY CAMERA NETWORK SWITCH
SECURITY CONTROL PANEL
SECURITY CAMERA PATCH PANEL
SECURITY CAMERA POWER SUPPLY
SURFACE HOUSING
SINGLEMODE FIBER OPTIC CABLE
SURFACE METAL RACEWAY
SURFACE MOUNT
SERIAL NETWORK MODULE
SURGE PROTECTOR
SPECIFICATION
LOUDSPEAKER LEVEL AUDIO
SURFACE PLASTIC RACEWAY
SURFACE RACEWAY
SERVER ROOM
SHIELDED TWISTED PAIR
SUSPENDED
S-VIDEO
TERMINATION BLOCK(S)
TELECOMMUNICATIONS BONDING BACKBONE
TO BE DETERMINED
TELECOMMUNICATIONS CONTRACTOR
TEMPERATURE CONTROL PANEL
TELEPHONE
TELECOMMUNICATIONS GROUNDING BUSBAR
TELECOMMUNICATIONS MAIN GROUNDING BUSBAR
TWISTED PAIR
TELECOMMUNICATIONS ROOM (IDF, FD)
TYPICAL
UNIT
UNDERGROUND
UNLESS OTHERWISE NOTED
UNSHIELDED TWISTED PAIR PATCH PANEL
UNINTERRUPTIBLE POWER SUPPLY
UNIVERSAL SERIAL BUS
UNSHIELDED TWISTED PAIR
VOICE BACKBONE
VOICE
HD ANALOG VIDEO TYP 15 PIN D-SUB
HD ANALOG VIDEO TYP 15 PIN D-SUB & 3.5MM TRS
VOICE-GRADE COPPER BACKBONE
VIRTUAL LOCAL AREA NETWORK
VIDEO MANAGEMENT STATION
VOICE OVER INTERNET PROTOCOL
VIDEO SURVEILLANCE SYSTEM
VIDEO TELE-CONFERENCING
VIDEO WALL
WALL TELEPHONE
WALL MOUNTED
WEATHER PROOF
WIRELESS ACCESS POINT
AUDIOVISUAL
SYMBOL
AE
DESCRIPTION
SYMBOL
COMMON WORK / ELECTRICAL
SHEET#
TITLE
DESCRIPTION
T0.00
T0.01
T0.02
T2.01
T4.01
T4.02
T5.01
T5.02
TECHNOLOGY TITLE SHEET
TECHNOLOGY PROJECT NOTES
TECHNOLOGY SCHEDULES
TECHNOLOGY PLAN - LEVEL 03
TECHNOLOGY SPACE PLANS
TECHNOLOGY SPACE PLANS
TECHNOLOGY DETAILS
TECHNOLOGY DETAILS
STRUCTURAL BLOCKOUT
AUDIOVISUAL EQUIPMENT LOCATION
WxH
A
LOUDSPEAKER
FSD
CABLE PATHWAY FIRESTOPPING DEVICE
FPA
FIRE-RATED FLOOR PENETRATION ASSEMBLY
VIDEO DISPLAY
PROJECTION SCREEN
CP
CONTROL PANEL
IF
INTERFACE PLATE
GROUND
CONDUIT WITH BUSHING
CONDUIT WITH CAP
PROJECTOR
A
FIXED CAMERA
A
PAN - TILT - ZOOM CAMERA
CONDUIT UP
CONDUIT DOWN
CONDUIT / CABLE HOME RUN
LECTERN
SR
A
AUDIOVISUAL DEVICE
A
AUDIOVISUAL CEILING DEVICE
A
SURFACE RACEWAY
CONDUIT UNDERGROUND / FLOOR / SLAB
AUDIOVISUAL FIELD LOCATED DEVICE
OSP
OSP UNDERGROUND DUCTBANK
P
PULL BOX
U
UTILITY POLE
CS
CABLE SUPPORT PATHWAY
(J-HOOKS / STRAPS / SLINGS)
CT
CABLE TRAY
GROUNDING BUSBAR
DRAWING ANNOTATIONS
DEVICE BOX EMPTY
SYMBOL
DESCRIPTION
DEVICE BOX EMPTY (CEILING)
FLOOR BOX
XX##
OR
#
POKE THRU
E
ENCLOSURE
KEYNOTE
#
DRAWING NOTE
XX### OR (XX###)
WALL BOX
#
EQUIPMENT RACK
*
EQUIPMENT SCHEDULE ID
REVISION NUMBER
ENLARGED FLOOR PLAN, SCHEDULE, OR DETAIL CALLOUT
REFERENCE INDICATOR
*
#
REFERENCE SHEET NUMBER
#
MAINTENANCE HOLE
SECTION OR ELEVATION CALLOUT
*
#
A
D
REFERENCE INDICATOR
REFERENCE SHEET NUMBER
*
#
ROOM WALL ELEVATION CALLOUT
#
A,B,C,D
#
B
WALL ELEVATION REFERENCE
REFERENCE SHEET NUMBER
C
BREAK LINE
CONTINUANCE LINE
X
DETAIL FURNISH / INSTALL CALLOUT (ON DETAILS WHERE CALLOUTS
ARE USED, ASSUME EC FOR X AND Y WHERE NOT INDICATED FOR
COMPONENTS) UON IN TECHNOLOGY RESPONSIBILITY MATRIX)
Y
X INDICATES ENTITY (ABBREVIATED) RIMROCK RECOMMENDS BE
RESPONSIBLE FOR FURNISHING
Y INDICATES ENTITY (ABBREVIATED) RIMROCK RECOMMENDS BE
RESPONSIBLE FOR INSTALLING
TELECOM AREA BOUNDARY LINE
COMMUNICATIONS
TELECOM ROOM BOUNDARY LINE
SYMBOL
DESCRIPTION
FUTURE EQUIPMENT, RACK, OR ENCLOSURE OUTLINE
TE
COMMUNICATIONS EQUIPMENT LOCATION
SYMBOL
CR
TYPICAL WALL MOUNTED DEVICE NOTATION. EXAMPLE:
CABLE RUNWAY
A
CEILING-MOUNTED SPEAKER
A
WALL-MOUNTED SPEAKER
CABLE - END LOOP
CABLE - CONTINUOUS LOOP
TYPICAL POLE OR BOOM MOUNTED DEVICE NOTATION. EXAMPLE:
SYMBOL
TELECOM OUTLET
TELECOM OUTLET (CEILING)
T
COMMUNICATIONS DEVICE
T
COMMUNICATIONS CEILING DEVICE
T
COMMUNICATIONS FIELD LOCATED DEVICE
S
WALL-MOUNTED SECURITY CAMERA
S
POLE-MOUNTED SECURITY CAMERA
TYPICAL DEVICE OR EQUIPMENT NON-STANDARD HEIGHT
(TELECOM OUTLET EXAMPLE SHOWN)
+H
H
INDICATES DIMENSION OF DEVICE OR EQUIPMENT
CENTERLINE (UON) ABOVE FINISHED FLOOR
TYPICAL STATION CALLOUT
XY
X
INDICATES NUMBER OF VOICE/DATA PORTS/CABLES
Y
INDICATES NUMBER OF COAX PORTS/CABLES
(ASSUME 0 IF BLANK)
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
FURNISH
NOTES APPLY
TO ALL ENTITIES
COLOMBINE HALL AUDIOVISUAL UPGRADES
ENTITY
COMPONENT
SHEET LIST
LEGEND
UNIVERSITY OF COLORADO COLORADO SPRINGS
TECHNOLOGY RESPONSIBILITY MATRIX
TYPICAL ASSEMBLY NOTATION, INCLUDES:
2
- INFRASTRUCTURE: FLOOR BOX, POKE-THRU, WALL BOX,
SURFACE RACEWAY, ENCLOSURE, HOUSING, RACK, ETC.
IF
- SERVICES: DEVICES AND/OR CABLING AS
SHOWN ASSOCIATED WITH INFRASTRUCTURE.
(FLOORBOX WITH INTERFACE PLATE AND
TELECOM OUTLET EXAMPLE SHOWN).
SYMBOL/DEVICE CONGESTION NOTATION INCLUDES:
LEGEND NOTES
ISSUE RECORD
No
2
2. SUBSCRIPTS ADJACENT SYMBOLS ELSEWHERE ON DRAWINGS INDICATE ADDITIONAL INFORMATION REGARDING APPLICATION
OF DEVICE OR EQUIPMENT. REFER TO ABBREVIATIONS, DRAWING ANNOTATIONS, SCHEDULES, AND SPECIFICATIONS FOR
ADDITIONAL SYMBOL SUBSCRIPT INFORMATION.
3. MULTIPLE SUBSCRIPTS ADJACENT A SYMBOL SIGNIFY MULTIPLE DEVICE TYPES OR MULTIPLE INSTALLATION REQUIREMENTS
FOR ONE OR MORE DEVICES. MULTIPLE SUBSCRIPTS REPRESENTING DIFFERENT DEVICE TYPES ADJACENT A SYMBOL IS
EQUIVALENT TO MULTIPLE DEVICES LOCATED AT THE SAME OR APPROXIMATE PLAN LOCATION, BUT AT DIFFERENT
ELEVATIONS. THE FIRST SUBSCRIPTS (STARTING FROM THE LEFT OR TOP) IS ASSOCIATED WITH THE DEVICE AT THE HIGHEST
ELEVATION, THE SECOND SUBSCRIPT IS ASSOCIATED WITH THE DEVICE AT THE NEXT HIGHEST ELEVATION, ETC.
Description
Date
LEADER INDICATOR: USED TO IDENTIFY INTENDED
LOCATION OF SYMBOL(S) THAT WOULD OTHERWISE
OVERLAP OR CREATE CONGESTION WITH OTHER
SYMBOLOGY.
1. NOT ALL ITEMS LISTED IN THIS LEGEND ARE USED ON TECHNOLOGY DRAWINGS.
A
TARGET INDICATOR: USED TO IDENTIFY INTENDED
LOCATION OF LEADER ARROWHEAD TERMINATION THAT
WOULD OTHERWISE OVERLAP OR CREATE CONGESTION
WITH OTHER SYMBOLOGY.
A
X
WALL
X
CONGESTION INDICATOR: USED TO IDENTIFY
ARRANGEMENT OF CONGESTED DEVICES.
X INDICATES CONGESTION TYPE:
H HORIZONTAL
V VERTICAL (ALONG SAME STUD OR STUD CAVITY)
B BOTH HORIZONTAL AND VERTICAL
-- SINGLE ITEM (NOT ALIGNED)
Client:
RIMROCK CONTACTS
Arvada Office
5420 Ward Road, Suite 200
Arvada, CO 80002
Phone: 303.422.7400
Colorado Springs Office
10807 New Allegiance Drive, Suite 400
Colorado Springs, CO, CO 80921
Phone: 719.533.1112
PROJECT MANAGER
Andy Burkart
719.886.2459
andy.burkart@rimrockgroup.com
CONSTRUCTION ADMINISTRATOR
Andy Burkart
719.886.2459
andy.burkart@rimrockgroup.com
UCCS
Project #:
81515004
Designed By:
RIMROCK
Drawn By:
RIMROCK
Approved By:
RIMROCK
Scale:
NONE
TECHNOLOGY TITLE
SHEET
100% CONSTRUCTION DOCUMENTS
10/23/2015
T0.00
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
GENERAL NOTES
GENERAL
AUDIOVISUAL
A
PROJECT NOTES INDICATE GENERAL REQUIREMENTS FOR WORK INDICATED ON THE
DRAWINGS. APPLICABLE PROJECT NOTES SHALL BE CONSIDERED PART OF GENERAL NOTES
FOR EACH SHEET.
A
PROJECT NOTES INDICATE GENERAL REQUIREMENTS FOR WORK INDICATED ON THE
DRAWINGS. APPLICABLE PROJECT NOTES SHALL BE CONSIDERED PART OF GENERAL NOTES
FOR EACH SHEET.
B
UNLESS OTHERWISE NOTED IN THE PROJECT NOTES, THE GENERAL REQUIREMENTS OF THE
PROJECT NOTES SHALL GOVERN WORK INDICATED ON THE DRAWINGS, UNLESS SPECIFIC
NOTATION ELSEWHERE ON THE DRAWINGS INDICATES DIFFERENT REQUIREMENTS, IN WHICH
CASE THE DIFFERENT REQUIREMENTS INDICATED ELSEWHERE SHALL GOVERN.
B
REVIEW ALL NOTES FOR ALL TRADES TO ASSURE FULL COORDINATION BETWEEN ALL TRADES.
C
SPEAKER LOCATIONS SHOWN ARE APPROXIMATE. COORDINATE SPEAKER LOCATIONS WITH
OTHER CEILING DEVICES. ENSURE THAT FINAL SPEAKER LOCATIONS MEET THE SOUND
REINFORCEMENT INTENT FOR THE TARGET AREA.
WORK SHALL COMPLY WITH THE GOVERNING REQUIREMENTS LISTED IN THE SPECIFICATIONS.
E
IF DISCREPANCIES OR CONFLICTS ARE DISCOVERED IN THE CONSTRUCTION DOCUMENTS, THE
CONTRACTOR SHALL NOTIFY THE ENGINEER IN WRITING AND WAIT FOR INSTRUCTION PRIOR TO
PROCEEDING WITH WORK RELATED TO DISCREPANCIES OR CONFLICTS.
F
SUBSTITUTIONS OF PRODUCT AND DEVIATIONS FROM METHODS OF CONSTRUCTION SPECIFIED
SHALL BE CONSIDERED AT SUBMITTAL REVIEW. SUCH SUBSTITUTIONS USED FOR BID SHALL BE
AT THE SOLE RISK OF CONTRACTOR, AND AS SUCH ARE SUBJECT TO REJECTION WITHOUT
CONSIDERATION.
G
RECORD DRAWINGS SHALL BE MAINTAINED ON SITE PER SPECIFICATIONS SHOWING
ADDITIONS, CHANGES, DELETIONS THROUGHOUT CONSTRUCTION.
H
I
PROVIDE SEISMIC BRACING AS REQUIRED BY THE GOVERNING REQUIREMENTS.
DRAWING ELEMENTS SHOWN IN GRAY ARE TO BE INSTALLED AS PART OF A DIFFERENT BID
PACKAGE OR PROVIDED BY OTHERS. WHERE SUCH ELEMENTS AFFECT THE CONTRACTORS
WORK, COORDINATE DEPENDENCIES WITH APPLICABLE OTHERS IN A TIMELY MANNER, BEFORE
SUCH DEPENDENCIES ARISE IN THE FIELD.
J
THIS PROJECT SHALL BE ACTIVELY MANAGED BY THE CONTRACTOR'S PROJECT MANAGER
WHICH SHALL NOT ALSO BE THE CONTRACTOR'S FOREMAN OR BE INVOLVED IN TECHNICAL
WORK IN THE FIELD. DOWNTIME, DELAYS OR NON-SCHEDULED OUTAGES DUE TO THE
CONTRACTOR'S FAILURE TO ACTIVELY MANAGE THE WORK, INCLUDING BUT NOT LIMITED TO
EFFECTIVELY PLANNING, SEQUENCING, SCHEDULING, AND EXECUTING THE WORK WILL NOT BE
ACCEPTABLE AT ANY TIME.
K
WORK REQUIRING UTILITY AND/OR TECHNOLOGY SYSTEM OUTAGES SHALL BE COORDINATED
WITH THE OWNER IN ADVANCE AND PRE-APPROVED IN WRITING.
L
COORDINATION IS REQUIRED PRIOR TO ROUGH-IN. DRAWINGS ARE DIAGRAMMATIC AND SHALL
NOT BE SCALED FOR BOX, DEVICE AND/OR EQUIPMENT LOCATIONS. LOCATIONS INDICATED
ARE APPROXIMATE AND DO NOT REPRESENT THE ACTUAL FIELD CONDITION OR FINAL
LOCATION. FURTHERMORE, REQUIREMENTS FOR ROUGH-IN BOXES, EQUIPMENT DIMENSIONS,
MOUNTING/HEIGHTS, SUPPORTS, FACEPLATES, CONDUIT ROUTING, AND/OR INTERFACES MAY
VARY. COORDINATE FINAL LOCATIONS AND REQUIREMENTS WITH ACTUAL FIELD CONDITIONS,
SHOP DRAWINGS, RESPECTIVE TRADE(S), ARCHITECT, AND/OR OWNER PRIOR TO ROUGH-IN.
M
WHERE COORDINATION DICTATES THAT FINAL LOCATIONS VARY SIGNIFICANTLY FROM THAT
SHOWN ON THE DRAWINGS, THE CONTRACTOR SHALL NOTIFY THE ENGINEER AND AWAIT
APPROVAL PRIOR TO ELECTRICAL ROUGH-IN.
N
IDENTIFY AND COORDINATE WITH OTHER TRADES LOCATION AND SIZE OF REQUIRED OPENINGS
IN NEW CONCRETE OR MASONRY PRIOR TO THE FORMING AND POURING OF CONCRETE OR
CONSTRUCTION OF MASONRY. OPENINGS MAY NOT BE INDICATED ON DRAWINGS.
O
CONTRACTOR SHALL COORDINATE ALL PENETRATIONS, OPENINGS, FASTENERS,
CONNECTIONS, HANGERS, AND SUPPORTS WITH STRUCTURAL DRAWINGS AND ENGINEER
PRIOR TO COMMENCEMENT OF WORK. WHEN LOCATING AND SIZING ALL PENETRATIONS
THROUGH THE STRUCTURAL SLABS REFER TO THE STRUCTURAL DETAILS DEPICTING
ALLOWABLE LOCATIONS AND OPENINGS. THE CONTRACTOR SHALL PREPARE A DRAWING(S) OF
ALL PENETRATIONS AND COORDINATE THIS DRAWING(S) WITH THE GENERAL CONTRACTOR
AND ALL OTHER TRADES TO VERIFY THAT THE LOCATIONS OF TECHNOLOGY REQUIRED
PENETRATIONS DO NOT CONFLICT WITH PENETRATIONS REQUIRED BY ALL OTHER TRADES.
P
PENETRATION OF CONCRETE AND STRUCTURAL ELEMENTS SHALL BE AVOIDED WHERE
POSSIBLE. OBTAIN WRITTEN APPROVAL FROM STRUCTURAL ENGINEER/ARCHITECT PRIOR TO
SUCH NECESSARY PENETRATIONS.
Q
PROVIDE SLEEVES FOR LOCATIONS WHERE CABLE PASSES THROUGH WALLS, FLOORS, OR
FOUNDATIONS. SLEEVES SHALL BE SIZED TO SUPPORT CABLES PER NEC FILL RATIOS AND
TIA/EIA 569 CABLE CAPACITY STANDARDS PLUS <25 PERCENT> FUTURE EXPANSION.
R
PROVIDE CABLE PATHWAY FIRESTOPPING DEVICES FOR LOCATIONS WHERE CABLE WILL
PENETRATE FIRE RATED BARRIERS. REFER TO ARCHITECTURAL DRAWINGS FOR WALL TYPE
INFORMATION. PROVIDE CABLE PATHWAY FIRESTOPPING DEVICE(S) IN SUFFICIENT QUANTITY
SUCH THAT THE COMBINED USEABLE CROSS SECTIONAL AREA OF THE DEVICE(S) MATCHES OR
EXCEEDS THE CROSS SECTIONAL AREA OF CABLE TRAY TO BE SERVED.
S
FOR EACH CABLE PATHWAY FIRESTOPPING LOCATION SHOWN FEEDING CABLE TRAY, PROVIDE
CABLE PATHWAY FIRESTOP DEVICE(S) IN SUFFICIENT QUANTITY SUCH THAT THE COMBINED
USEABLE CROSS-SECTIONAL AREA OF THE DEVICE(S) IS GREATER THAN OR EQUAL TO THE
CROSS-SECTIONAL AREA OF CABLE TRAY TO BE SERVED. FOR ALL OTHER FIRESTOP
LOCATIONS, PROVIDE CABLE PATHWAY FIRESTOP DEVICE(S) IN SUFFICIENT QUANTITY SUCH
THAT THE COMBINED USEABLE CROSS-SECTIONAL AREA OF THE DEVICE(S) IS GREATER THAN
THE CROSS-SECTIONAL AREA OF ALL CABLES TO PASS THROUGH THE DEVICES, PLUS THE
ADDITIONAL AMOUNT (PERCENTAGE) REQUIRED BY THE SPECIFICATIONS OR ELSEWHERE FOR
FUTURE EXPANSION.
T
PER NEC REQUIREMENTS, TECHNOLOGY ITEMS SHALL NOT BE SECURED TO OR SUPPORTED BY
SUSPENDED CEILING SYSTEM (INCLUDING SUPPORTS WIRES), HANGERS FOR CABLE
SUPPORTS SHALL BE INDEPENDENT (DEDICATED). PER NEC REQUIREMENTS, WIRE HANGERS
SHALL BE SUPPORTED AT BOTH ENDS AND DISTINGUISHABLE FROM SUSPENDED CEILING
SYSTEM SUPPORT WIRE. IN EXPOSED STRUCTURAL CEILING SPACES, WIRE SHALL NOT BE
USED AS A HANGER FOR SUPPORT.
U
HANGERS AND SUPPORTS SHALL BE PROVIDED AT INTERVALS PER THE NEC, SHALL BE
ATTACHED TO STRUCTURE AND NOT BE ATTACHED TO OTHER BUILDING SYSTEMS AND THEIR
ASSOCIATED SUPPORTS. CABLE SUPPORTS SHALL BE MOUNTED AT VARYING INTERVALS NOT
TO EXCEED 5 FEET AND ROUTED PARALLEL AND PERPENDICULAR TO BUILDING LINES. CABLE
SUPPORTS SHALL NOT SHARE CABLES OF DIFFERENT TECHNOLOGY SYSTEMS OR EXCEED 50
PERCENT OF THE MANUFACTURER'S RECOMMENDED FILL. INCLUDE CABLE SUPPORT ROUTING
ON RECORD DRAWINGS.
V
CABLE DAMAGED BY THE CONTRACTOR SHALL BE REPLACED BY THE CONTRACTOR WITHIN 4
HOURS OF THE DAMAGING EVENT, AT NO ADDITIONAL COST TO THE OWNER.
W
COORDINATE WITH AUDIOVISUAL EQUIPMENT SUPPLIER AND SHOP DRAWINGS TO FINALIZE ALL
STRUCTURAL SUPPORT REQUIREMENTS AND LOCATIONS FOR DISPLAYS, PROJECTORS AND
PROJECTION SCREENS PRIOR TO ROUGH-IN.
X
SPEAKER LOCATIONS SHOWN ARE APPROXIMATE. COORDINATE SPEAKER LOCATIONS WITH
OTHER CEILING DEVICES. ENSURE THAT FINAL SPEAKER LOCATIONS MEET THE SOUND
REINFORCEMENT INTENT FOR THE TARGET AREA.
COMMON WORK / ELECTRICAL
A
PROJECT NOTES INDICATE GENERAL REQUIREMENTS FOR WORK INDICATED ON THE
DRAWINGS. APPLICABLE PROJECT NOTES SHALL BE CONSIDERED PART OF GENERAL NOTES
FOR EACH SHEET.
B
EVERY CONTRACTOR IS RESPONSIBLE FOR REVIEWING THE GENERAL NOTES - GENERAL
SECTION FOR PROJECT NOTES THAT APPLY TO MORE THAN ONE TRADE AS WELL AS ALL
OTHER NOTES PROVIDED FOR OTHER TRADES FOR FULL COORDINATION BETWEEN ALL
TRADES.
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
D
COLOMBINE HALL AUDIOVISUAL UPGRADES
EXAMINE THE CONTRACT DOCUMENTS IN THEIR ENTIRETY, INCLUDING BUT NOT LIMITED TO
GENERAL AND SUPPLEMENTAL REQUIREMENTS, DRAWINGS AND SPECIFICATIONS OF OTHER
DIVISIONS, AND ADDENDA, FOR EQUIPMENT OR WORK WHICH MAY AFFECT WORK UNDER THIS
SECTION, REGARDLESS OF WHETHER SUCH REQUIREMENTS OR WORK ARE SPECIFICALLY
INDICATED IN THIS SECTION.
UNIVERSITY OF COLORADO COLORADO SPRINGS
C
ISSUE RECORD
No
Description
Client:
Date
UCCS
Project #:
81515004
Designed By:
RIMROCK
Drawn By:
RIMROCK
Approved By:
RIMROCK
Scale:
NONE
TECHNOLOGY PROJECT
NOTES
100% CONSTRUCTION DOCUMENTS
10/23/2015
T0.01
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
DETAIL INDEX
ACCESSIBLE: EASY ACCESS. ACCESS ATTAINED WITHOUT REQUIRING EXTENSIVE REMOVAL
OF OTHER MATERIALS TO GAIN ACCESS.
B
ACCESSIBLE CEILING: ACOUSTICAL TILE HANGING CEILINGS (“HARD-LID” CEILINGS (CONCEALED
SPINE OR SHEETROCK/GYPSUM CEILINGS), EVEN WHEN PROVIDED WITH ACCESS PANELS, ARE
NOT CONSIDERED AN ACCESSIBLE CEILING.)
C
BY OTHERS: A PARTY OR ENTITY OTHER THAN THE CONTRACTOR. THE CONTRACTOR SHALL
ENGAGE THE GENERAL CONTRACTOR, ARCHITECT, AND/OR OWNER TO DETERMINE THIS PARTY
OR ENTITY FOR CONSIDERATION OF PRICING AND/OR EXECUTION OF THE WORK.
D
COMMUNICATIONS (OR TECHNOLOGY) GROUNDING SYSTEM: INCLUDES (BUT IS NOT LIMITED
TO) PROVIDING A PERMANENT GROUNDING AND BONDING INFRASTRUCTURE FOR THE
COMMUNICATIONS CABLING SYSTEM.
E
ELECTRICAL FOR COMMUNICATIONS SYSTEMS ALSO REFERED TO AS COMMUNICATIONS (OR
TECHNOLOGY) PATHWAY SYSTEM: INCLUDES (BUT IS NOT LIMITED TO) DEVICE BOXES, PULL
BOXES, CONDUIT, CABLE TRAY, DUCT/DUCTBANK, AND OTHER PATHWAY AND RACEWAY
COMPONENTS NECESSARY TO PROVIDE PATHWAY FOR, SUPPORT, AND ROUTE
COMMUNICATIONS CABLES.
F
G
H
SHEET
TA-CRS - CEILING RECESSED SCREEN DETAIL
TA-CSD - CEILING SPEAKER DETAILS
TA-IFB - BACK BOX DETAIL FOR AV WALL INTERFACE REQUIRING BACKING
TA-IFER - BACK BOX DETAIL FOR AV EQUIPMENT RACK
TA-IFW - BACK BOX DETAIL FOR AV WALL INTERFACE
TA-PMD - PROJECTOR MOUNT DETAILS
TA-TTIF - TABLE TOP INTERFACE DETAIL
TA-VCW - BACK BOX DETAIL FOR AV DEVICE CONTROL
T5.01
T5.01
T5.01
T5.01
T5.01
T5.02
T5.01
T5.01
AUDIOVISUAL
SYMBOL
AE
A
SUBSCRIPT
AUDIOVISUAL EQUIPMENT LOCATION
SHARED RACK SPACE (TYP TR)
CONCEALED: HIDDEN FROM SIGHT IN INTERSTITIAL BUILDING SPACES, CHASES, FURRED
SPACES, SHAFTS, CRAWL SPACES, ETC.
STANDARD (WALL)
TYPE A
TYPE B
TYPE C
LOUDSPEAKER (CEILING)
STANDARD ACT (REPLACEMENT
OR CUT-IN)
N
NON-ACCESSIBLE CEILING
P
PENDANT
S
SUB-WOOFER
DS
VIDEO DISPLAY (CEILING)
PLENUM ACT CEILING
A
ACT CEILING
DS
DIGITAL SIGNAGE
E
EXPOSED
N
NON-ACCESSIBLE CEILING
K
GOVERNING AUTHORITY: ENTITIES OR THEIR REPRESENTATIVES CHARGED WITH FORMATION
AND/OR ENFORCEMENT OF GOVERNING REQUIREMENTS, SUCH AS THE AUTHORITY HAVING
JURISDICTION (AJH).
PROJECTION SCREEN
STANDARD (WALL)
L
M
INSTALL: TO PLACE IN FINAL POSITION IN FULLY OPERABLE, TESTED CONDITION.
PROVIDE: TO FURNISH AND INSTALL, COMPLETE, TESTED AND READY FOR INTENDED USE.
N
ROUGH-IN: PROVIDE THE COMMUNICATIONS PATHWAY SYSTEM, INCLUDING (BUT NOT LIMITED
TO) DEVICE BOXES, PULL BOXES, WALL BOXES, FLOOR BOXES, POKE-THROUGH DEVICES,
CONDUIT, ENCLOSURES, CABLE TRAY, DUCTS/DUCTBANKS, MAINTENANCE HOLES, HAND
HOLES, AND OTHER PATHWAYS AND ITEMS INDICATED (OR AS REQUIRED) FOR ROUTING,
SUPPORTING, AND INSTALLING COMMUNICATIONS CABLES, DEVICES, OR EQUIPMENT WHICH
SHALL BE PROVIDED BY OTHERS OR PROVIDED UNDER A SUBSEQUENT SET OF CONTRACT
DOCUMENTS.
PROJECTION SCREEN (CEILING)
RECESSED
C
SUSPENDED
CP
PHASING SCHEDULE
317
3/21/16 THRU 3/27/16
322, 325
NOTES
SCD 3/23/16 4PM
3
5/16/16 THRU 6/12/16
323, 324, 333
3A
5/16/16 THRU 5/21/16
334
SCD 5/18/16 4PM
3B
6/6/16 THRU 6/11/16
329
SCD 6/8/16 4PM
DETAILS
ID
TA-IFWB
FSD
CABLE PATHWAY FIRESTOPPING DEVICE
TE-WFS
FS102
FPA
FIRE-RATED FLOOR PENETRATION ASSEMBLY
TE-FFS
FS110
GROUND
CONDUIT WITH BUSHING
CONDUIT WITH CAP
TA-CSD
TA-CSD
CONDUIT UP
CONDUIT / CABLE HOME RUN
SURFACE RACEWAY
OSP
TA-PMD
TA-PMD
TA-WMS
CONTROL PANEL
STANDARD (BACKBOX)
A
TYPE A
T
TABLE TOP / TOUCH PANEL
INTERFACE PLATE
STANDARD (WALL)
B
TYPE B
C
TYPE C
F
STANDARD, FLOOR
T
TABLE TOP / FURNITURE
OSP UNDERGROUND DUCTBANK
P
PULL BOX
U
UTILITY POLE
CS
SHORT THROW (INTERACTIVE)
SHORT THROW (PRESENTATION)
TYPE B
TA-CRS
TA-CSS
PROJECTOR (CEILING)
PLENUM ACT CEILING
A
ACT CEILING
E
EXPOSED
N
NON-ACCESSIBLE CEILING
2) SIGNIFICANT COMPLETION DATE (SCD) SHALL BE 5 BUSINESS DAYS PRIOR TO END OF GIVEN
PROJECT PHASE UNLESS OTHERWISE NOTED.
PROJECTOR LIFT
CEILING MOUNTED
A
FIXED CAMERA (CEILING)
(NO SUBSCRIPT)
A
TYPE A
A
PAN - TILT - ZOOM CAMERA
(NO SUBSCRIPT)
A
TYPE A
A
PAN - TILT - ZOOM CAMERA (CEILING)
(NO SUBSCRIPT)
A
TYPE A
CABLE TRAY (DEPTH x WIDTH)
(NO SUBSCRIPT)
TA-IFCP
TA-IFCP
TA-IFW
DEVICE BOX EMPTY
(NO SUBSCRIPT)
AV
AUDIOVISUAL
TA-FIF
TA-TIF
FF
S
SEP
TA-WPD
FURNITURE FEED
SECURITY
SITE EMERGENCY PHONE
DEVICE BOX EMPTY (CEILING)
(NO SUBSCRIPT)
AV
AUDIOVISUAL
TA-PMD
TA-PMD
TA-PMD
TA-PMD
S
JS001
JS010
TE-BJ, TE-CT,
TE-CTUB,
TE-CR
CT201
SECURITY
GB020
GB010
TE-CR
TE-CR,
TA-DETAILS
TE-CR
TS-SD
TE-CR
TA-IFB
TE-CR,
TA-DETAILS
TS-SD
FLOOR BOX
FB4
FB6
FB8
FB10
FBF
TA-PL
POKE THRU
PT6
PT8
PTF
TA-IFB
TA-IFB
E
(NO SUBSCRIPT)
4-GANG
6-GANG
8-GANG
10-GANG
FURNITURE FEED
TE-FB
TE-FB
TE-FB
TE-FB
TE-FB
TE-FB
6-INCH
8-INCH
FURNITURE FEED
CB001
CB004
CB006
CB008
CB010
CB015
CB023
CB025
ENCLOSURE
S
LECTERN
AUDIOVISUAL CEILING BOX
SECURITY CEILING ENCLOSURE
TA-PE
TS-SD
WALL BOX
(NO SUBSCRIPT)
A
TE-CR
GROUNDING BUSBAR
TGB
GROUND BUS
TMBG
MAIN GROUND BUS
NOTES:
1) CONFIRM ALL DATES WITH UCCS PROJECT MANAGEMENT.
MH400
CABLE SUPPORT PATHWAY
(NO SUBSCRIPT)
J
J-HOOKS
PROJECTOR
A
B
SR100
CONDUIT UNDERGROUND / FLOOR / SLAB
TA-PMD
TA-PMD
CT-DxW
IF
12/21/15 THRU 1/8/16
DESCRIPTION
WxH
TC SERIES
SR
EXPOSED: NOT CONCEALED AND NOT INSTALLED UNDERGROUND.
FURNISH: TO PURCHASE, SUPPLY, AND DELIVER TO THE PROJECT MATERIALS IN NEW AND
OPERABLE CONDITION, READY FOR INSTALLATION.
2
SUBSCRIPT
STRUCTURAL BLOCKOUT (WIDTH x HEIGHT)
STANDARD (WALL)
DIGITAL SIGNAGE
I
J
1
SYMBOL
VIDEO DISPLAY
CONTRACT DOCUMENTS: THE AGREEMENT (INCLUDING OTHER DOCUMENTS LISTED IN THE
AGREEMENT), CONDITIONS OF THE CONTRACT (GENERAL, SUPPLEMENTARY AND OTHER
CONDITIONS), AND THE CONSTRUCTION DOCUMENTS.
PHASE
ID
CONDUIT DOWN
CONSTRUCTION DOCUMENTS: COLLECTIVE TERM FOR THE ENTIRE SET OF BOUND OR
UNBOUND MATERIAL DESCRIBING THE CONSTRUCTION AND SERVICES REQUIRED, INCLUDING
ALL DRAWINGS, SPECIFICATIONS, ADDENDA ISSUED PRIOR TO EXECUTION OF THE CONTRACT,
AND MODIFICATIONS ISSUED AFTER EXECUTION OF THE CONTRACT (SUCH AS CHANGE
ORDERS, CONSTRUCTION CHANGE DIRECTIVES, SUPPLEMENTAL INSTRUCTIONS, ETC.).
PROJECT PHASING SCHEDULE
DATES
ROOMS
DETAILS
LOUDSPEAKER
A
B
C
A
DESCRIPTION
COMMON WORK / ELECTRICAL
VIDEO DISPLAY
AUDIOVISUAL DEVICE
ALS
ASSISTIVE LISTENING
AP
WIRELESS ACCESS POINT
TRANSCEIVER
S
SCREEN SWITCH
VC
VOLUME CONTROL
WM
WIRELESS MIC ANTENNA
A
AUDIOVISUAL CEILING DEVICE
ALS
ASSISTIVE LISTENING
AP
WIRELESS ACCESS POINT
TRANSCEIVER
M
MICROPHONE
WM
WIRELESS MIC ANTENNA
A
AUDIOVISUAL FIELD LOCATED DEVICE
DM
DUAL-ELEMENT BOUNDARY
MICROPHONE
M
MICROPHONE
TM
TRI-ELEMENT BOUNDARY
MICROPHONE
WC
WEB CAM
EQUIPMENT RACK
AUDIOVISUAL (FLOOR)
W
AUDIOVISUAL (WALL)
TA-DWB
TA-IFER
TA-IFWR
HAND HOLE
(NO SUBSCRIPT)
MAINTENANCE HOLE
(NO SUBSCRIPT)
TE-MH,
TE-MHCE
MH100
DETAILS
ID
COMMUNICATIONS
SYMBOL
T E
CR-X
SUBSCRIPT
DESCRIPTION
COMMUNICATIONS EQUIPMENT LOCATION
(NO SUBSCRIPT)
CABLE RUNWAY (X INDICATES MINIMUM WIDTH IN INCHES)
(NO SUBSCRIPT)
TC-CR,
TC-CRAD
A
ALTERNATE SPACING
TC-CR,
TC-CRAD
ER200
ER201
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
A
DETAIL
COLOMBINE HALL AUDIOVISUAL UPGRADES
GENERAL
DEVICE SCHEDULE
UNIVERSITY OF COLORADO COLORADO SPRINGS
TERMS AND DEFINITIONS
CABLE - END LOOP
(NO SUBSCRIPT)
CABLE - CONTINUOUS LOOP
(NO SUBSCRIPT)
TELECOM OUTLET
(NO SUBSCRIPT)
AC
ABOVE COUNTER
AV
AUDIOVISUAL
DS
E
ELEC
ELV
EP
F
FACP
K
LCP
MECH
POS
S
SR
VND
W
WAP
DIGITAL SIGNAGE
EMERGENCY INFORMATION
BOARD
ELECTRICAL EQUIPMENT
ELEVATOR EQUIPMENT
EMERGENCY BLUE PHONE
FURNITURE MOUNTED
FIRE ALARM CONTROL PANEL
KIOSK
LIGHTING CONTROL PANEL
MECHANICAL/HVAC EQUIPMENT
POINT OF SALE
SECURITY CAMERA
SURFACE RACEWAY
VENDING MACHINE
WALL TELEPHONE
WIRELESS ACCESS POINT
TELECOM OUTLET (CEILING)
(NO SUBSCRIPT)
AV
AUDIOVISUAL
DS
E
S
WAP
DIGITAL SIGNAGE
EMERGENCY INFORMATION
BOARD
SECURITY CAMERA
WIRELESS ACCESS POINT
TE-CR
TE-CR
TE-CR,
TA-DETAILS
TE-CR,
TA-DETAILS
TE-CR
ISSUE RECORD
No
Description
Date
TE-CR
TE-CR
TE-CR
TE-CR
TE-CR
TE-CR
TE-CR
TE-CR
TS-CD
TE-CR
TE-CR
TE-CR
TE-CR
TE-CR,
TA-DETAILS
TE-CR,
TA-DETAILS
TE-CR
Client:
UCCS
Project #:
81515004
Designed By:
RIMROCK
Drawn By:
RIMROCK
Approved By:
RIMROCK
Scale:
NONE
TS-CD
TE-CR
TECHNOLOGY
SCHEDULES
T
COMMUNICATIONS DEVICE
(NO SUBSCRIPT)
T
COMMUNICATIONS CEILING DEVICE
(NO SUBSCRIPT)
100% CONSTRUCTION DOCUMENTS
10/23/2015
T
COMMUNICATIONS FIELD LOCATED DEVICE
(NO SUBSCRIPT)
T0.02
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
DEMOLITION NOTES
A
ABANDON ALL EXISTING COPPER AND FIBER AUDIOVISUAL CABLING. PROVIDE STAINLESS
STEEL BLANK COVER FOR OUTLET BOX AT LECTERN. REMOVE CABLING FROM EXISTING
PROJECTOR POLE MOUNT AND AMX TELEVISION MANAGER AND LEAVE NEATLY COILED AT
PROJECTOR LOCATION ABOVE CEILING. REMOVE AND RETURN AUDIO AMPLIFIER (LOCATED
NEAR PROJECTOR ABOVE CEILING), CEILING SPEAKERS, AMX TELEVISION MANAGER,
PROJECTOR, AND SCREEN TO OWNER. REUSE EXISTING PROJECTOR POLE AND PROJECTOR
MOUNTING HARDWARE. REMOVE AND DISPOSE OF PODIUM.
KEYNOTES
313
UP
314
316B
312B
312A
316
UNIVERSITY OF COLORADO COLORADO SPRINGS
316A
312
315
312C
312D
312E
312F
304
317
T-4.02
307
304A
T4.02
DN
308
320
312H
303
318
1
312G
305
301
300A
302
UP
310
321
335
1
1
1
T4.01
T4.01
T4.01
1
T4.01
TE04
TE04
T-4.01
TE04
T-4.01
TE04
T-4.01
T-4.01
333
334
323
322
328
1
T4.01
325
324
T-4.01
T-4.01
TE04
331
329
1
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
337
PROVIDE OUTLET BOXES FOR AUDIOVISUAL, TELECOMMUNICATIONS, AND
ELECTRICAL SERVICES TO LECTERN AT THIS LOCATION. REFER TO DETAIL TA-IFER
FOR RECOMMENDED LAYOUT AND ASSUMED TELECOMMUNICATION AND ELECTRICAL
REQUIREMENTS TO BE CONFIRMED BY OWNER. REFER TO RISER DIAGRAM ON
TECHNOLOGY SPACE PLAN FOR ADDITIONAL INFORMATION AND REQUIREMENTS FOR
AUDIOVISUAL OUTLET BOXES.
COLOMBINE HALL AUDIOVISUAL UPGRADES
DN
TE04
1
T4.01
T4.01
T-4.01
TE04
ISSUE RECORD
326
DN
TE04
330
No
327
Description
Date
338
Client:
N
1
TECHNOLOGY PLAN - LEVEL 03
T2.01
8'
4'
0
1/8" = 1'-0"
8'
UCCS
Project #:
81515004
Designed By:
RIMROCK
Drawn By:
RIMROCK
Approved By:
RIMROCK
Scale:
As indicated
TECHNOLOGY PLAN LEVEL 03
100% CONSTRUCTION DOCUMENTS
10/23/2015
T2.01
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
GENERAL NOTES
A
TE03
TA02
REVIEW ALL CONTRACT DOCUMENTS FOR PROJECT REQUIREMENTS. TECHNOLOGY SPACE
PLANS MAY NOT BE PROVIDED FOR ALL SYSTEMS AND ARE NOT EXHAUSTIVE. INFORMATION
PROVIDED IS PROGRAMMATIC; SOME ANCILLARY EQUIPMENT MAY BE SHOWN HEREIN FOR
CLARITY, BUT NOT ALL ANCILLARY EQUIPMENT IS SPECIFIED. PROVIDE ALL COMPONENTS
NECESSARY FOR A FULLY FUNCTIONAL SYSTEM(S) READY FOR THE OWNERS USE.
REQUIREMENTS FOR POWER, MOUNTING, CABLE MANAGEMENT, COOLING, AND OTHER
MISCELLANEOUS COMPONENTS REQUIRED FOR A FULLY FUNCTIONING SYSTEM ARE ASSUMED
AND SHALL BE PROVIDED BY THE CONTRACTOR.
SA
1 W
6
TE05
A
IF
IF
B
TE03
PROVIDE EMPTY 4 11/16" DEVICE BOX WITH SINGLE GANG MUD RING AND BLANK
COVER PLATE FOR FUTURE CAMERA INTERFACE ADJACENT TO SCREEN. LOCATE
IMMEDIATELY ABOVE WRITING SURFACE APPROXIMATELY (7) SEVEN FEET (6) SIX
INCHES AFF. LOCATE TO SIDE OF SCREEN NEAREST LECTERN APPROXIMATELY (1)
ONE FOOT FROM EDGE OF SCREEN.
TE05
AS ROOM LAYOUTS VARY, LOCATIONS SHALL BE REVIEWED AND CONFIRMED DURING
THE MANDATORY CONSTRUCTION KICKOFF MEETING PRIOR TO PERFORMING ANY
WORK. REFER TO RISER DIAGRAM ON TECHNOLOGY SPACE PLAN AND DETAIL
TA-IFER FOR GENERAL INFORMATION AND REQUIREMENTS. THE TYPICAL ORDER OF
OUTLET BOXES FROM FRONT TO BACK OF THE ROOM SHALL BE: SCREEN SWITCH,
TELEPHONE OUTLET, DATA OUTLET, AV INTERFACE PLATES, THEN ELECTRICAL
OUTLET.
T4.01
A
2
TOUCHPANEL 7"
*
TSW-752
POE
CC
CC
16:10 ELECTRIC
RECESSED
SCREEN
*
60" x 96"
TENSIONED
ADVANTAGE 113"
DIAGONAL
CC
SCREEN SWITCH
*
AS REQUIRED
TABLE STAND KIT
FOR TSW-750
TSW-750-TTK-X-S
TO NETWORK
BY OTHERS
POE SWITCH 5
PORT
CEN-SW-POE-5
IP
HDBT
HDBT
TO NETWORK
BY OTHERS
IP
PROJECTOR
*
G6470WU
IP
TO NETWORK
BY OTHERS
VGA
LL LR
HDMI
N
1
CLASSROOM ENLARGED FLOOR PLAN
SMART
LECTURN
CABLE POCKET
T4.01
4'
2'
0
1/4" = 1'-0"
4'
MIC
LM
LM
DETAIL
AV-D1
SPKR
8 OHM
DIGITALMEDIA
PRESENTATION
SYSTEM
*
DMPS3-4k-150-C
CV
LL LR
ASSISTED
LISTENING
SYSTEM
(OFOI)
AUDIO AMPLIFIER
*
DCi 2 | 300
LM
INTERFACE
PLATE
CUSTOM
As Required
HDMI DA &
EXTRACTOR HDMI
*
HD-DA-2
WALL SURFACE
LOUDSPEAKER
*
CDD5x
HDMI
TO NETWORK
BY OTHERS
IP
COMPUTER
(OFCI)
USB
TO NETWORK
BY OTHERS
IP
TO NETWORK
BY OTHERS
IP
DOCUMENT
CAMERA
*
VZ-3
APPLE TV
*
APPLE TV
HDMI
HDMI
SMART LECTERN
MT-400-UCCS-MAPLE-NATURAL -7302
2
CLASSROOM PRESENTATION WALL ELEVATION
5
T4.01
CLASSROOM AUDIOVISUAL ONE-LINE DIAGRAM
T4.01
4'
2'
0
1/4" = 1'-0"
4'
CEILING
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
CENTER PROJECTOR SCREEN AND SPEAKER ON EXISTING PROJECTOR MOUNT
LOCATION. AS ROOM LAYOUTS VARY, LOCATIONS SHALL BE REVIEWED AND
CONFIRMED DURING THE MANDATORY CONSTRUCTION KICKOFF MEETING PRIOR TO
PERFORMING ANY WORK. TYPICAL LOCATION SHALL BE APPROXIMATELY FIVE FEET
FROM PRESENTATION WALL. USE CEILING MOUNT WITH TILE BRIDGE AND SAFETY
CABLE AS REQUIRED.
COLOMBINE HALL AUDIOVISUAL UPGRADES
TA02
UNIVERSITY OF COLORADO COLORADO SPRINGS
KEYNOTES
2
BASE BID:
PROVIDE FLEX CONDUITS FOR NEW AV,
TELECOM AND POWER OUTLETS
+90"
(2) 1-INCH CONDUITS
ADD ALTERNATE #1
(2) 1-INCH CONDUITS
A S
+48"
(2) 1 1/4-INCH CONDUITS
PROVIDE HARD CONDUITS FOR NEW AV,
TELECOM AND POWER OUTLETS
ISSUE RECORD
(2) 1 1/4-INCH CONDUITS
No
(REF. DETAIL TA-IFER)
+18" IF
FLOOR
RISER GENERAL NOTES
C. ADDITIONAL CONDUITS FOR TELECOMM OR POWER MAY BE REQUIRED.
REFERENCE DEVICE DETAILS AND TELECOMM AND ELECTRICAL PLANS.
RISER DRAWING NOTES
1. REFERENCE DETAIL TA-IFER FOR GENERAL LAYOUT INFORMATION AND
ASSUMED ELECTRICAL AND TELECOMM REQUIREMENTS TO BE CONFIRMED
BY OWNER. LOCATE OUTLET BOXES SERVING LECTERN LOCATION PER
KEYNOTE ON TECHNOLOGY FLOOR PLANS. PROVIDE A BLANK PLATE FOR
ONE OF THE BOXES TO BE LEFT AS SPARE FOR FUTURE USE.
DESCRIPTION
TYPE
A
A. ALL MEASUREMENTS ARE TO CENTER UNLESS OTHERWISE NOTED.
B. STUB ALL CONDUITS TO ACCESSIBLE CEILING SPACE OF SAME ROOM
UNLESS OTHERWISE ILLUSTRATED/NOTED IN RISER DIAGRAM.
S
MANUFACTURER
PART NUMBER
SPECIAL RQMTS
2 CHANNEL AUDIO AMPLIFIER
CROWN
DCi 2 | 300
WALL SURFACE LOUDSPEAKER
MARTIN
CDD5x
DOCUMENT CAMERA
WOLFVISION
VZ-3
DIGITALMEDIA PRESENTATION SYSTEM
CRESTRON
DMPS3-4k-150-C
HDMI DA & EXTRACTOR
CRESTRON
HD-DA-2
PROJECTOR
EPSON
G6470WU
APPLE TV
APPLE
APPLE TV
16:10 ELECTRIC RECESSED SCREEN
DA-LITE
60" x 96" TENSIONED ADVANTAGE 113" DIAGONAL
SCREEN SWITCH
DA-LITE
AS REQUIRED
TOUCHPANEL 7"
CRESTRON
TSW-752
TABLE STAND KIT FOR TSW-750
CRESTRON
TSW-750-TTK-X-S
POE SWITCH 5 PORT
CRESTRON
CEN-SW-POE-5
SMART LECTERN
ATF
MT-400-UCCS-MAPLE-NATURAL-7302
POWER CONDITIONER
FURMAN
P-8 PRO II
INTERFACE PLATE CUSTOM
RCI CUSTOM
As Required
SPEAKON
NEUTRIK
As Required
ETHERCON CAT6A SHIELDED
NEUTRIK
As Required
For Digital Media
Net Connect Cable XG620 4pr 23 AWG CMP Yellow Jacket
AMP
4-1499416-7
For Digital Media
DISPLAY POLE MOUNTING HARDWARE
CHIEF
AS REQUIRED
REUSE EXISTING
PROJECTOR MOUNT
CHIEF
RPAU
(5) REUSE EXISTING, (2) NEW
MOUNTING BRACKET AS REQ.
Client:
AS REQUIRED
T4.01
UCCS
Project #:
81515004
Designed By:
RIMROCK
Drawn By:
RIMROCK
Approved By:
RIMROCK
Scale:
3
Date
EQUIPMENT SCHEDULE
+18" IF
1
Description
As indicated
CLASSROOM RISER DIAGRAM
TECHNOLOGY SPACE
PLANS
100% CONSTRUCTION DOCUMENTS
10/23/2015
T4.01
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
GENERAL NOTES
A
A
A
W
TE02
B
1 6
IF
IF
IF
TE02
REVIEW ALL CONTRACT DOCUMENTS FOR PROJECT REQUIREMENTS. TECHNOLOGY SPACE
PLANS MAY NOT BE PROVIDED FOR ALL SYSTEMS AND ARE NOT EXHAUSTIVE. INFORMATION
PROVIDED IS PROGRAMMATIC; SOME ANCILLARY EQUIPMENT MAY BE SHOWN HEREIN FOR
CLARITY, BUT NOT ALL ANCILLARY EQUIPMENT IS SPECIFIED. PROVIDE ALL COMPONENTS
NECESSARY FOR A FULLY FUNCTIONAL SYSTEM(S) READY FOR THE OWNERS USE.
REQUIREMENTS FOR POWER, MOUNTING, CABLE MANAGEMENT, COOLING, AND OTHER
MISCELLANEOUS COMPONENTS REQUIRED FOR A FULLY FUNCTIONING SYSTEM ARE ASSUMED
AND SHALL BE PROVIDED BY THE CONTRACTOR.
TE05
TE01
A
TE03
KEYNOTES
TA01
CENTER SPEAKER ON SCREEN AND LOCATE SPEAKER OUT OF LINE OF SIGHT FROM
SEATED POSITION IN BACK ROW TO THE TOP OF PROJECTION SCREEN.
TA03
PROJECTOR SCREEN AND SWITCH ARE EXISTING TO REMAIN.
TE01
PROVIDE SPEAKER OUTLET BOXES WITH APPROPRIATE BACKING (AS REQUIRED)
FOR CEILING SURFACE MOUNTED SPEAKERS. CENTER MIDDLE OUTLET BOX
HORIZONTALLY ON SCREEN. LOCATE ALL THREE OUTLET BOXES (4) FOUR FEET
FROM WEST (PRESENTATION) WALL. LOCATE LEFT AND RIGHT OUTLET BOXES (4)
FOUR FEET FROM SIDE WALL. PROVIDE BACKING (AS REQUIRED) IMMEDIATELY
ADJACENT TO BOX AND EXTEND EAST (TOWARD CENTER OF ROOM) AS FAR AS
DRYWALL SLOPE CONTINUES, APPROXIMATELY (7) SEVEN FEET FROM WEST
(PRESENTATION) WALL.
TE02
LOCATE OUTLET BOX AS HIGH AS POSSIBLE ON WALL. COORDINATE LOCATION WITH
AV CONTRACTOR PRIOR TO PERFORMING ANY WORK.
TE03
PROVIDE EMPTY 4 11/16" DEVICE BOX WITH SINGLE GANG MUD RING AND BLANK
COVER PLATE FOR FUTURE CAMERA INTERFACE ADJACENT TO SCREEN. LOCATE
IMMEDIATELY ABOVE WRITING SURFACE APPROXIMATELY (7) SEVEN FEET (6) SIX
INCHES AFF. LOCATE TO SIDE OF SCREEN NEAREST LECTERN APPROXIMATELY (1)
ONE FOOT FROM EDGE OF SCREEN.
TE05
AS ROOM LAYOUTS VARY, LOCATIONS SHALL BE REVIEWED AND CONFIRMED DURING
THE MANDATORY CONSTRUCTION KICKOFF MEETING PRIOR TO PERFORMING ANY
WORK. REFER TO RISER DIAGRAM ON TECHNOLOGY SPACE PLAN AND DETAIL
TA-IFER FOR GENERAL INFORMATION AND REQUIREMENTS. THE TYPICAL ORDER OF
OUTLET BOXES FROM FRONT TO BACK OF THE ROOM SHALL BE: SCREEN SWITCH,
TELEPHONE OUTLET, DATA OUTLET, AV INTERFACE PLATES, THEN ELECTRICAL
OUTLET.
S
A
T4.02
A
2
TE01
TE01
A
TE02
S TA03
A
A
TE02
A
TOUCHPANEL 7"
*
TSW-752
N
1
POE
CC
CC
FILM SCREENING CLASSROOM ENLARGED FLOOR PLAN
TABLE STAND
KIT
FOR TSW-750
TSW-750-TTK-X-S
T4.02
4'
2'
0
1/4" = 1'-0"
4'
CC
(EXISTING)
TO NETWORK
BY OTHERS
IP
SCREEN SWITCH
*
AS REQUIRED
(EXISTING)
POE SWITCH 5
PORT
CEN-SW-POE-5
HDBT
HDBT
TO NETWORK
BY OTHERS
16:10 ELECTRIC
RECESSED
SCREEN
*
57.5" x 92"
TENSIONED
ADVANTAGE 109"
DIAGONAL
IP
PROJECTOR
*
G6470WU
IP
TO NETWORK
BY OTHERS
VGA
LL LR
HDMI
SMART
LECTURN
CABLE POCKET
SPKR
8 OHM
TA01
CV
LL LR
MIC
ASSISTED
LISTENING
SYSTEM
(OFOI)
LM (FROM HD-XSP)
LM
DETAIL
AV-D1
DIGITALMEDIA
PRESENTATION
SYSTEM
*
DMPS3-4k-150-C
HDMI
SURROUND
SOUND
PROCESSOR
*
HD-XSP
LM (QTY. 8)
8 CHANNEL AUDIO
AMPLIFIER
*
DCi 8 | 300
L/R/C & SURROUND
(QTY. 7)
HDMI
TO NETWORK
BY OTHERS
IP
WALL SURFACE
LOUDSPEAKER
*
CDD5x
SPKR
COMPUTER
(OFCI)
8 OHM
USB
TO NETWORK
BY OTHERS
DOCUMENT
CAMERA
*
VZ-3
IP
INTERFACE
PLATE
CUSTOM
As Required
HDMI
CEILING
SUBWOOFER
*
CONTROL 312CS
CEILING SUB WOOFER BACKBOX
MTC-300BB12
CEILING SUB WOOFER GRILLE
MTC-300SG12
RS232
2
BLU-RAY PLAYER
*
DN-500BD
FILM SCREENING CLASSROOM PRESENTATION WALL ELEVATION
T4.02
4'
2'
0
1/4" = 1'-0"
HDMI
4'
HDMI SWITCHER 4K
*
HD-MD4X1-4K-3
HDMI
HDMI
TO NETWORK
BY OTHERS
IP
IP
APPLE TV
*
APPLE TV
CEILING
(1) 3/4-INCH CONDUIT
A
(1) 3/4-INCH CONDUIT
A
1
+90"
SMART LECTERN
MT-400-UCCS-MAPLE-NATURAL -7302
BASE BID:
PROVIDE FLEX CONDUITS FOR NEW AV,
TELECOM AND POWER OUTLETS
4
(2) 1-INCH CONDUITS
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
2
A
COLOMBINE HALL AUDIOVISUAL UPGRADES
TA03
UNIVERSITY OF COLORADO COLORADO SPRINGS
TA01
FILM SCREENING CLASSROOM ONE-LINE DIAGRAM
T4.02
(2) 1 1/4-INCH CONDUITS
ADD ALTERNATE #1
PROVIDE HARD CONDUITS FOR NEW AV,
TELECOM AND POWER OUTLETS
(2) 1 1/4-INCH CONDUITS
(2) 1 1/4-INCH CONDUITS
(REF. DETAIL TA-IFER)
+18" IF
FLOOR
+18" IF
+18" IF
ISSUE RECORD
2
No
Description
Date
EQUIPMENT SCHEDULE
DESCRIPTION
TYPE
RISER GENERAL NOTES
A. ALL MEASUREMENTS ARE TO CENTER UNLESS OTHERWISE NOTED.
S
B. STUB ALL CONDUITS TO ACCESSIBLE CEILING SPACE OF SAME ROOM
UNLESS OTHERWISE ILLUSTRATED/NOTED IN RISER DIAGRAM.
C. ADDITIONAL CONDUITS FOR TELECOMM OR POWER MAY BE REQUIRED.
REFERENCE DEVICE DETAILS AND TELECOMM AND ELECTRICAL PLANS.
RISER DRAWING NOTES
1. REFER TO ENLARGED FLOOR PLAN AND RELEVENT KEYNOTES FOR
SPEAKER OUTLET BOX QUANTITY AND LOCATION INFORMATION.
AUDIOVISUAL CONTRACTOR SHALL REVIEW SPEAKER MOUNTING BRACKET
AND WIRE MANAGEMENT AND COORDINATE EXACT REQUIREMENTS WITH
OWNER.
2. REFERENCE DETAIL TA-IFER FOR GENERAL LAYOUT INFORMATION AND
ASSUMED ELECTRICAL AND TELECOMM REQUIREMENTS TO BE CONFIRMED
BY OWNER. PROVIDE A BLANK PLATE FOR ONE OF THE BOXES TO BE LEFT
AS SPARE FOR FUTURE USE.
3
T4.02
FILM SCREENING CLASSROOM RISER DIAGRAM
A
MANUFACTURER
PART NUMBER
SURROUND SOUND PROCESSOR
CRESTRON
HD-XSP
8 CHANNEL AUDIO AMPLIFIER
CROWN
DCi 8 | 300
CEILING SUBWOOFER
JBL
CONTROL 312CS
CEILING SUB WOOFER - BACKBOX
JBL
MTC-300BB12
CEILING SUB WOOFER - GRILLE
JBL
MTC-300SG12
WALL SURFACE LOUDSPEAKER
MARTIN
CDD5x
DOCUMENT CAMERA
WOLFVISION
VZ-3
BLU-RAY PLAYER
DENON
DN-500BD
HDMI SWITCHER - 4K
CRESTRON
HD-MD4X1-4K-3
DIGITALMEDIA PRESENTATION SYSTEM
CRESTRON
DMPS3-4k-150-C
PROJECTOR
EPSON
G6470WU
APPLE TV
APPLE
APPLE TV
TOUCHPANEL 7"
CRESTRON
TSW-752
TABLE STAND KIT FOR TSW-750
CRESTRON
TSW-750-TTK-X-S
POE SWITCH 5 PORT
CRESTRON
CEN-SW-POE-5
SPECIAL RQMTS
MOUNTING BRACKET AS REQ.
Client:
SMART LECTERN
ATF
MT-400-UCCS-MAPLE-NATURAL-7302
POWER CONDITIONER
FURMAN
P-8 PRO II
INTERFACE PLATE CUSTOM
RCI CUSTOM
As Required
SPEAKON
NEUTRIK
As Required
ETHERCON CAT6A SHIELDED
NEUTRIK
As Required
For Digital Media
Net Connect Cable XG620 4pr 23 AWG CMP Yellow Jacket
AMP
4-1499416-7
For Digital Media
DISPLAY POLE MOUNTING HARDWARE
CHIEF
AS REQUIRED
REUSE EXISTING
PROJECTOR MOUNT
CHIEF
RPAU
REUSE EXISTING
AS REQUIRED
UCCS
Project #:
81515004
Designed By:
RIMROCK
Drawn By:
RIMROCK
Approved By:
RIMROCK
Scale:
As indicated
TECHNOLOGY SPACE
PLANS
100% CONSTRUCTION DOCUMENTS
10/23/2015
T4.02
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
BASE BID:
PROVIDE FLEX CONDUITS FOR NEW AV,
TELECOM AND POWER OUTLETS
ADD ALTERNATE #1
PROVIDE HARD CONDUITS FOR NEW AV,
TELECOM AND POWER OUTLETS
INSULATED THROAT
BUSHING
INSULATED THROAT
BUSHING
AV CABLING
STUB CONDUIT
6-INCHES INTO
ACCESSIBLE
CEILING UNLESS
OTHERWISE
NOTED
INSULATED THROAT
BUSHING
AV CABLING
AVC AVC
AVC AVC
BEND RADIUS = 6
x INTERNAL
DIAMETER
BEND RADIUS = 6
x INTERNAL
DIAMETER
BEND RADIUS = 6
x INTERNAL
DIAMETER
CEILING LEVEL
(REF:
ARCHITECTURAL)
STUB CONDUIT
6-INCHES INTO
ACCESSIBLE CEILING
UNLESS OTHERWISE
NOTED
STUB CONDUIT
6-INCHES INTO
ACCESSIBLE CEILING
UNLESS OTHERWISE
NOTED
CEILING LEVEL
(REF:
ARCHITECTURAL)
CEILING LEVEL
(REF:
ARCHITECTURAL)
WALL
(REF:
ARCHITECTURAL)
WALL
(REF:
ARCHITECTURAL)
#
TELECOM OUTLET BOX
4 11/16 - INCH SQUARE
MIN 2 1/8 - INCH DEEP BOX
FRAMING
MUDRING
(REF: TABLE FOR SIZE)
FRAMING
(REF: ARCHITECTURAL)
AV OUTLET BOX
4 11/16 - INCH SQUARE
MIN 2 1/8 - INCH DEEP BOX
FLOOR
(REF:
ARCHITECTURAL)
SEE AV
RISER
DIAGRAM
TELECOM OUTLET BOX
4 11/16 - INCH SQUARE
MIN 2 1/8 - INCH DEEP BOX
SEE AV
RISER
DIAGRAM
TYPE
BOX
MUDRING
--
2
2
A
2
1
--
--
--
BACK BOX DETAIL FOR AV WALL INTERFACE REQUIRING BACKING
A
SCALE: NONE
FLOOR
(REF:
ARCHITECTURAL)
MATCH TO
LIGHT
SWITCH
MOUNTING
HEIGHT
2 GANG
MUDRING
GANG SIZE
TA-IFB
#
FLOOR
(REF:
ARCHITECTURAL)
16" O.C.
TYP.
DUPLEX POWER
RECEPTACLE
(REF: ELECTRICAL)
AV OUTLET BOX
4 11/16 - INCH SQUARE
MIN 2 1/8 - INCH DEEP BOX
16" O.C.
TYP.
SEE AV
RISER
DIAGRAM
DETAIL GENERAL NOTES
1 GANG
MUDRING
A
A
TA-IFW
BACK BOX DETAIL FOR AV WALL INTERFACE
IF
SCALE: NONE
TA-IFER
2 GANG
MUDRING
A. LOCATIONS SHALL BE REVIEWED AND
CONFIRMED DURING THE MANDATORY
CONSTRUCTION KICKOFF MEETING. REFER
TO RISER DIAGRAM AND TECHNOLOGY
FLOOR PLAN FOR ADDITIONAL
INFORMATION AND REQUIREMENTS.
BACK BOX DETAIL FOR AV LECTERN LOCATIONS
SCALE: NONE
CONDUIT
EC EC
TO STRUCTURE
INSULATED THROAT
BUSHING
HANGER WIRE
TILE BRIDGE
AVC AVC
LOUDSPEAKER
CABLE
LOUDSPEAKER
CUTOUT AREA
AVC AVC
4" x 4"
ELECTRICAL BOX
AVC AVC
AIRCRAFT CABLE
TO STRUCTURE
EC EC
BEND RADIUS = 6
x INTERNAL
DIAMETER
AVC AVC
LOUDSPEAKER
CABLE
TRIM RING
AVC AVC
AVC AVC
AV CABLING
STUB CONDUIT
6-INCHES INTO
ACCESSIBLE CEILING
UNLESS OTHERWISE
NOTED
CEILING LEVEL
(REF:
ARCHITECTURAL)
LOUDSPEAKER
CUTOUT AREA
EXTRON AAP SCHEDULE
Qty
1
1
1
1
TA-TTIF
Part #
Model Name
60-300-02
70-103-18
60-1346-02
70-092-72
AAP 102
One XLR 3-pin Male to Solder Cups, One XLR 3-pin Female to Solder Cups - Neutrik
USB PowerPlate 200 AAP (Single-space)
Three RCA Female to Solder Cup (Silkscreen)
LOUDSPEAKER
ACCESSIBLE CEILING
(REF: ARCHITECTURAL)
AVC AVC
TABLE TOP INTERFACE DETAIL
LOUDSPEAKER
AVC AVC
NON-ACCESSIBLE CEILING
(REF: ARCHITECTURAL)
WALL
(REF:
ARCHITECTURAL)
N
A
A
ACCESSIBLE CEILING
NON-ACCESSIBLE CEILING
AV OUTLET BOX
4 11/16 - INCH SQUARE
MIN 2 1/8 - INCH DEEP BOX
IF T
SCALE: NONE
ATTACH TO
STRUCTURE
THREADED
ROD
UNISTRUT
STRUCTURAL
SUPPORT ONE
FOOT LONGER
THAN CASE
CEILING FAN
TYPE DEVICE
BOX
THREADED ROD
CONDUIT
1 GANG
MUDRING
EC EC
CONNECT
POWER TO
SCREEN OR LOW
VOLTAGE
CONTROLLER AS
REQUIRED
(REF:
ELECTRICAL)
MOUNT TO
UNISTRUT
SUPPORT
AVC AVC
CEILING
(REF: ARCHITECTURAL)
LOUDSPEAKER
CABLE
AVC AVC
FACEPLATE
AIRCRAFT CABLE
AVC AVC
FORGED
EYE BOLT
AVC AVC
CEILING
(REF:
ARCHITECTURAL)
CEILING RECESSED SCREEN DTL.
SCALE: NONE
DETAIL GENERAL NOTES
MATCH TO
LIGHT
SWITCH
MOUNTING
HEIGHT
A. LOCATE ELECTRICAL BOX AND CONDUIT
OUTSIDE OF LOUDSPEAKER CUTOUT AREA.
COORDINATE WITH AUDIO VISUAL CONTRACTOR
PRIOR TO CONDUIT INSTALLATION.
AVC AVC
SCREEN BOTTOM OF
VIEWABLE
AREA SHALL
BE 48" AFF
UON. PROVIDE
EXTRA DROP
AS REQUIRED.
B. MOUNT EYE BOLT ONTO CUSTOM
MANUFACTURED DEVICE BOX FACEPLATE.
FACEPLATE MADE OF 1/8-INCH ALUMINUM WITH
1/2-INCH PASS THRU HOLE FOR CABLE SET OFF
CENTER.
ISSUE RECORD
LOUDSPEAKER
A
AVC AVC
AVC AVC
TA-CRS
FLOOR
(REF:
ARCHITECTURAL)
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
WALL
(REF:
ARCHITECTURAL)
GC GC
UNIVERSITY OF COLORADO COLORADO SPRINGS
BACKING
BOARD
COLOMBINE HALL AUDIOVISUAL UPGRADES
AV OUTLET BOX
MIN 2 1/8 - INCH DEEP BOX
P
PENDANT CEILING
TA-CSD
CEILING SPEAKER DETAILS
SCALE: NONE
C. UTILIZE THEATER GRADE RIGGING HARDWARE
INCLUDING BUT NOT LIMITED TO: AIRCRAFT
CABLE, CABLE CLIPS, CABLE THIMBLES AND EYE
BOLTS.
A
A
N
A
No
P
TA-VCW
BACK BOX DETAIL FOR AV DEVICE CONTROL
SCALE: NONE
A S
Description
Date
A VC
Client:
UCCS
Project #:
81515004
Designed By:
RIMROCK
Drawn By:
RIMROCK
Approved By:
RIMROCK
Scale:
As indicated
TECHNOLOGY DETAILS
100% CONSTRUCTION DOCUMENTS
10/23/2015
T5.01
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
1
ATTACH TO
STRUCTURE
PLENUM ENCLOSURE
(REF AV TECHNOLOGY PLANS)
EC EC
AVC AVC
ATTACH TO
STRUCTURE
ATTACH TO
STRUCTURE
THREADED
ROD
EDGE-PROTECTED
BUNDLED CABLE INLET
CAVITY ON EACH SIDE
OF BOX, FILLED WITH
FLAME RETARDANT
FOAM SEAL
KNOCKOUT
#
FOR TELECOM
ATTACH TO
STRUCTURE
AV CABLING
ATTACH TO
STRUCTURE
DUPLEX POWER
RECEPTACLE
(REF: ELECTRICAL)
C. USE RIGID CONDUIT FOR ALL OUTLET BOXES.
D. MOUNT PROJECTOR IN SUCH A WAY AS NOT TO BE
OBSTRUCTED BY LIGHT FIXTURES, SPRINKLER
HEADS, ETC.
POLE MOUNT
UNI-STRUT
STRUCTURAL
SUPPORT FRAME
AVC AVC
POLE MOUNT
UNI-STRUT
STRUCTURAL
SUPPORT FRAME
AVC AVC
UNI-STRUT
STRUCTURAL
SUPPORT FRAME
AV CABLING
AVC AVC
TELECOM OUTLET BOX
4 11/16 - INCH SQUARE #
1 GANG MUD RING
MIN 2 1/8 - INCH DEEP BOX
POLE MOUNT
CEILING TILE
(REF: ARCHITECTURAL)
DUPLEX POWER
RECEPTACLE
(REF: ELECTRICAL)
CEILING GRID
(REF: ARCHITECTURAL)
DUPLEX POWER
RECEPTACLE
(REF: ELECTRICAL)
FIXED CEILING
(REF: ARCHITECTURAL)
TELECOM OUTLET BOX
4 11/16 - INCH SQUARE #
1 GANG MUD RING
MIN 2 1/8 - INCH DEEP BOX
CEILING TILE
(REF: ARCHITECTURAL)
ESCUTCHEON RING
POLE
ESCUTCHEON RING
TELECOM OUTLET BOX
4 11/16 - INCH SQUARE #
1 GANG MUD RING
MIN 2 1/8 - INCH DEEP BOX
AVC AVC
AVC AVC
POLE
PROJECTOR MOUNT
AVC AVC
AVC AVC
PROJECTOR
B. COORDINATE WITH ARCHITECT AND AUDIOVISUAL
CONTRACTOR FOR PROJECTOR PLACEMENT PRIOR
TO INSTALLING PROJECTOR STRUCTURAL SUPPORT.
THREADED
ROD
CEILING GRID
(REF: ARCHITECTURAL)
POWER
(REF: ELECTRICAL)
ATTACH TO
STRUCTURE
FRONT VIEW
AVC AVC
#
AVC AVC
AV OUTLET BOX
4 11/16 - INCH SQUARE
2 GANG MUD RING
MIN 2 1/8 - INCH DEEP BOX
POLE
FRONT VIEW
#
A
FRONT VIEW
PROJECTOR MOUNT
NOT SHOWN
N
F. MOUNT PROJECTOR AS CLOSE TO THE CEILING AS
POSSIBLE. REFER TO GENERAL NOTES D AND E
AND ARCHITECTURAL DRAWINGS.
DETAIL DRAWING NOTES
1. REUSE EXISTING PROJECTOR MOUNTING
STRUCTURE. PROVIDE NEW TELECOM OUTLET
BOX.
#
NON-ACCESSIBLE CEILING
ACCESSIBLE CEILING
AV OUTLET BOX
4 11/16 - INCH SQUARE
2 GANG MUD RING
MIN 2 1/8 - INCH DEEP BOX
POLE
AVC AVC
AVC AVC
PROJECTOR MOUNT
NOT SHOWN
AVC AVC
E. DIGITAL KEYSTONE CORRECTION SHALL NOT BE
USED. PROJECTOR SHALL BE LOCATED AND
ADJUSTED FIRST BY MOUNT THEN BY OPTICAL
ADJUSTMENT(S) SO THE IMAGE IS FREE OF ANY
KEYSTONING OR OTHER DISTORTION AND FILLS
PROJECTION SCREEN/AREA.
PROJECTOR MOUNT
NOT SHOWN
E
EXPOSED CEILING
FRONT VIEW
CEILING
PLATE
#
AVC AVC
PLENUM CEILING
BOTTOM VIEW
TA-PMD
PROJECTOR MOUNT DETAILS
SCALE: NONE
SCREEN
BOTTOM VIEW
SCREEN
BOTTOM VIEW
SCREEN
#
#
A #
N #
E
AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80918
THREADED ROD
MOUNTING KIT
THREADED ROD
A. UNI-STRUT FRAMEWORK SHOULD BE PROVIDED TO
ALLOW PROJECTOR TO BE MOUNTED ANYWHERE IN
FRONT HALF OF THROW RANGE OF SPECIFIED
PROJECTOR AND LENS.
COLOMBINE HALL AUDIOVISUAL UPGRADES
THREADED ROD
DETAIL GENERAL NOTES
ATTACH TO
STRUCTURE
UNIVERSITY OF COLORADO COLORADO SPRINGS
ATTACH TO
STRUCTURE
ISSUE RECORD
No
Description
Client:
Project #:
Designed By:
Drawn By:
Approved By:
Scale:
Date
UCCS
81515004
Designer
Author
Approver
NONE
TECHNOLOGY DETAILS
100% CONSTRUCTION DOCUMENTS
10/23/2015
T5.02
© Copyright BCER Engineering Inc.
Copyright reserved. All parts of this drawing are the exclusive
property of BCER Engineering and shall not be used or
reproduced in any manner without express written consent.
Download