Date:
FS#
Model 326
USFS Model 326
Inspection Form
UNIT DESIGNATION: _____________
FS#: _________
EQUIPT DESIGNATION (E#): __________
CONTRACT #:
CONTRACTOR: ____________________________
VIN: _____________________________
MILEAGE: ______________
TEST DRIVEN: Y
N
FUEL LEVEL: ________
INSPECTED BY: ________________________________
TITLE: ________________________________
This inspection form represents a checklist designed to assist the Forest Service and Contractor in assuring the
fire apparatus inspected is compliant with Forest Service national standard specifications. This form is not allinclusive and should not be utilized as a solicitation document.
INSPECTOR: When applicable, each item as listed should be thoroughly examined and tested to ensure
compliance. Check-marking of the item indicates that it is acceptable to the Government. Any deficiencies
shall be documented in the notes section, with a direct reference to the object and item number.
CHASSIS SPECIFICATIONS
International 7400 Series, 4 door Crew Cab, 4X2, 37,000 GVWR
Contractor furnished: ______
Government furnished: ______
1. ______185” wheelbase
2. ______74” cab to axle
3. ______front tow hooks
NOTES:
October 2011
Page 1
Date:
Model 326
FS#
4. ______20” front frame extension (length reduced as needed)
5. ______dual air brake system
6. ______exhaust system, vertical tailpipe and guard
7. ______alternator, 12 VDC, 200 amp
8. ______battery system, 3 1950 CCA, jump start stud remote mounted
9. ______engine, diesel, 330 HP
10. ______automatic Allison transmission
11. ______2 speed transfer case without PTO provision
12. ______70 gallon steel fuel tank
13. ______spare tire
CHASSIS ELECTRICAL
1. ______battery master switch, located on floorboard, driver’s side BRAND: _________________
2. ______battery ON indicator switch
3. ______ECM programming
4. ______back-up alarm
5. ______map light
6. ______ground lights, 4” LED, 2 each side under chassis steps
NOTES:
October 2011
Page 2
Date:
Model 326
FS#
TRAFFIC WARNING SYSTEMS
1. ______electric siren
2. ______speaker
3. ______forward upper Zone A/B/D Light Bar, 55”, mounted on cab roof
BRAND: _____________
____six (6) flashing LED modules, one at each corner, two forward-facing
____two forward-facing STEADY RED
____all red lenses
4. ______aft upper Zone B/D warning lights, 2 red LED, side-facing
5. ______upper Zone C warning light, 2 red LED, rear-facing; 1 amber LED, rear-facing on driver’s side
6. ______lower Zone A warning lights, 2 red LED, cab grill, forward-facing
7. ______forward lower Zone B/D warning lights, 2 red LED, chassis tilt hood, side-facing
8. ______aft lower Zone B/D warning lights, 2 red LED, side-facing, on beavertails
9. ______lower Zone C warning lights, 2 LED , rear-facing, housed with DOT lights
10. ______air horn, under hood, passenger’s side
11. ______headlight flasher (Wig Wag)
12. ______antennas, 4 bases
13. ______wiring, secured and protected
NOTES:
October 2011
Page 3
Date:
Model 326
FS#
CHASSIS ADDITIONS AND MODIFICATION
1. ______label indicating apparatus fluid types and quantities
2. ______seating capacity for 5
3. ______seats, 3 SCBA seats (OPTION), BRAND: _____________
4. ______seat belts, red, 3-point on 4 outboard seats, 2-point lap belt for rear center
5. ______seat belt warning label
6. ______vehicle height warning label
7. ______Final Stage Manufacturer Vehicle Certification
8. ______noise hazard warning label
9. ______air filter ember protection screen warning label
10. ______cab console, center, steel, black, with:
____2-1/2” discharge pressure gauge, 0-600 psi, backlit, BRAND____________
____mini display tank level gauge, BRAND_____________
____electronic siren controller, BRAND_______________
____map light
____12V power outlets, 4
NOTES:
October 2011
Page 4
Date:
Model 326
FS#
____3 switch panels, with 14 switches and pilot lights, numbered/function labeled:
1 – EMERGENCY MASTER
2 – LIGHT BAR
3 – WARN LIGHTS
4 – REAR AMBER
5 – WIG WAG
6 – HI/LO
7 – HORN/SIREN
8 – LEFT SCENE
9 – REAR SCENE
10 – RIGHT SCENE
11 – MAP LIGHT
12 – GROUND LIGHTS
13 – DIRECT LEFT
14 – CENTER OUT
15 – DIRECT RIGHT
11. ______center console aft storage
12. ______front tow hooks
13. ______front bumper extension, covered with diamondplate, support bracing
14. ______heat protective wrap, cab steps
15. ______hose storage tray, dimensions: _____”L X _____”W X _____”D
16. ______front fenders, rubber
17. ______mud flaps, no logos
18. ______chock block storage compartments
19. ______exhaust system
20. ______air lines, fuel lines ,electric harnesses protected
21. ______cabin air ember guard
22. ______transmission PTO
October 2011
Page 5
Date:
Model 326
FS#
APPARATUS BODY
1. ______body construction
framework of structural steel tubing
compartments installed from interior and permanently attached by welding
stainless steel fasteners
no sharp edges
structural seams fully seam welded
other seams caulked
2. ______body subframe
subframe of structural steel tubing
crossmembers, 2” X 3”
steel plate gussets
3. ______body mounting
4. ______drop moldings
5. ______vertical surfaces, covered with polished aluminum tread
6. ______grab handle, at rear on passenger’s side, mounted vertically
7. ______rear step, black dura-coat
8. ______rear step warning label
9. ______hose bed access ladder, pull-out, drop down step provided under bumper
10. ______driver’s side compartments
____forward of rear wheels, 39”W X 41”H X 14”D
____forward of rear wheel, lower, 39”W X 6”H X 19”D
____forward of rear wheel, foam system storage, 39”W X 10”H X 19”D
NOTES:
October 2011
Page 6
Date:
Model 326
FS#
driver’s side compartments cont.
____behind rear wheels, lower, 18.5”W X 22”H X 14”D
____over rear wheels, forward, 35.5”W X 31”H X 14”D
____over rear wheels, aft, 35.5”W X 31”H X 25”D
11. ______passenger’s side compartments
____forward of rear wheels, 39”W X 52”H X 14”D upper/24”D lower section
____forward of rear wheel, lower hose storage, 39”W X 6”H X 24”D
____behind rear wheels, lower, 18.5”W X 22”H X 14”D, vented
____over rear wheels, forward, 35.5”W X 31”H X 14”D
____over rear wheels, aft, 35.5”W X 31”H X 25”D
12. ______hose reel compartment, center rear, 40”W X 30”H X 27”D
13. ______dunnage compartments, 2 accessible from top, 56”L X 11”W X 14”D
14. ______compartments doors, aluminum overlap type, reflective striping
15. ______door latches, hardware, hold open devices
16. ______rear roll-up door
17. ______compartment floor mats, except in foam pump compartment
18. ______adjustable shelf channels
19. ______tool bracket mounting channels
20. ______weatherstripping
NOTES:
October 2011
Page 7
Date:
Model 326
FS#
21. ______compartment shelves, aluminum plate
____3 in driver’s side compartment forward of rear wheels
____2 each (4 total) in compartments above rear wheels on passenger’s side
22. ______I-Zone brackets
23. ______fenders and wheel wells
24. ______SCBA spare bottle storage, 4 locking compartments in wheel well (OPTION)
25. ______body scuff guards
26. ______hose bed, above water tank, removable extruded aluminum slat floor
27. ______hose bed dividers
28. ______hose bed cover
____gas strut
____4 handrails, two 18” long, directly ahead of ladder, two 24” long, one on each cover
____black fabric flap at rear of each cover section, secured with straps & metal buckles
____4 rope tie down brackets
____dura-coat non-skid surface
29. ______stainless steel body trim
30. ______hard suction hose storage, one each side of body
NOTES:
October 2011
Page 8
Date:
Model 326
FS#
PUMP AND PLUMBING
1. ______pump, Hale Model CBP, pump serial # _____________________
____pump body
____impellers
____pump shaft
____drive unit construction
The pump shall be capable of delivering 200 GPM minimum at 300 PSI output pressure from a 5 ft. lift through
24 ft. of 3” suction hose with a strainer and also from the apparatus water tank when installed on the
apparatus. This shall be measured through both the #19 and #3 rear discharges.
RPM
PSI
Free Flow
150
300
400
GPM
2. ______PTO shift
3. ______pump shift indicator lights
____”PUMP ENGAGED”
____”OK TO PUMP”
____”OK TO PUMP AND ROLL”
4. ______rear mounted pump operator’s panel
5. ______pump/plumbing compartment, accessible through floor of hose reel compartment
6. ______pump panel lights
NOTES:
October 2011
Page 9
Date:
Model 326
FS#
VALVES, CONTROLS, GAUGES & PLUMBING
1. ______on pump operator’s control panel
____pump performance acceptance test plate
____pump operator’s instruction plate
____test gauge connections
____pump panel labeling
____master discharge pressure gauge, 4-1/2”, 0-600 PSI, backlit
____master intake pressure gauge, 4-1/2”, 30-0-150 PSI, backlit
____master drain
____engine status center
____remote throttle control
____automatic pump override
____water tank level sight gauge
____water tank level electronic gauges
____foam tank level gauge
2. ______pump cooler/by-pass line
3. ______gauge drains, behind pump panel
4. ______priming pump
5. ______pressure relief valve
NOTES:
October 2011
Page 10
Date:
Model 326
FS#
6. ______discharge location:
____2-1/2” #19 water only, at rear
____1-1/2”, #3, plumbed to foam system, driver’s side between cab and body
____1-1/2”, #3, plumbed to foam system, passenger’s side between cab and body
____1-1/2”, #3, plumbed to foam system, passenger’s side, front bumper
____2”, #20, to isolate mid-passenger’s side & front bumper discharge piping
____two 1-1/2”, #3, with 2” plumbing & 1’1/2” valves, with foam, at rear
7. ______intake location:
____3”, #8, at rear
8. ______brass caps and chains
9. ______tank fill
10. ______tank to pump line
11. ______direct tank fill/drain
12. ______back back fill
13. ______check valves, #2, #17, #19, drains for winterization
14. ______hose reel
15. ______foam proportioning system
16. ______foam upload system, 3-way valve to select “tank fill,” “flush,” “switch off”
NOTES:
October 2011
Page 11
Date:
Model 326
FS#
WATER TANK
1. ______construction
____material, polypropylene
____lifting eyes on top of tank
____combination vent and manual fill tower
____sump
____tank outlets
2. ______clean out plug
3. ______tank capacity, 600 gallons
4. ______foam tank, 25 gallon capacity, fill tower lid labeled
BODY ELECTRICAL
1. ______wiring loomed, color coded and function labeled at 6” intervals
2. ______wiring securely fastened with metal clamps and nylon wire ties
3. ______rear DOT lighting
____tail lights, brake lights
____turn signal lights
____back-up lights
4. ______license plate bracket and light
5. ______rear upper marker lights
NOTES:
October 2011
Page 12
Date:
Model 326
FS#
6. ______cluster/clearance lights and reflectors
____3 red LED marker lights, at rear, below hose bed exit threshold
____2 red LED marker lights, on vertical surface of rear step, side-facing
____2 red reflectors, one each side, lower rear corner of compt doors, side-facing
____2 red reflectors, one each side, lower corners, above rear step, rear-facing
____2 amber reflectors, one each side, corners compt doors, forward compt. side-facing
7. ______rear directional light bar, provided at rear, 39” wide, 14 lamps
8. ______scene lights
____upper rear passenger’s side, rear-facing
____upper passenger’s side, centered front to rear, side-facing
____upper driver’s side, centered front to rear, side-facing
9. ______compartment lights
____4 each compartment, 2” diameter, 2 each side wall, one above shelf, one below
____one 4” diameter, recess mounted in the inside door panel, all compartments
10. ______hose bed lighting, two 4” diameter, inside surface of hosebed cover, one each side
11. ______electrical system performance test certification/documentation
NOTES:
_____
October 2011
Page 13
Date:
Model 326
FS#
APPARATUS FINISH
1. ______compartment interiors, finish painted with Zolatone (Apollo Gray color)
2. ______apparatus body color, Forest Service green
3. ______striping
4. ______lettering
____”FIRE” in stripe, 4” white
____unit & equipment designators, both sides, 8” white
____at rear, “USDA,” “FOREST SERVICE,” 3” green
____at rear, “FIRE,” unit & equipt designators in 4” green
____unit designator, passenger’s side front bumper, 6” white
____equipment designator, driver’s side front bumper, 6” white
____equipment designators on roof, 18” black
5. ______Government furnished door decals
6. ______truck identification plate
EQUIPMENT
1. ______manuals and drawings
2. ______road kit
____fire extinguisher
____set of warning triangle reflectors
____12 ton hydraulic jack with handle
3. ______wheel chocks
4. ______tool holders
October 2011
Page 14
Date:
Model 326
FS#
5. ______nozzle kit
____six ¾” GHT
____seven 1” NPSH
____two 1-1/2” NPSH
____eleven 1-1/2” NH
____two 2-2/1” NH
____one 2-1/2” NH quick release
NOTES:
October 2011
Page 15