Bluetooth 2.0+EDR module
BM-MP-CS-05 Preliminary Datasheet
Data Sheet
www.usi.com.tw
May 2007 Rev 1.0b
Introduction
The Bluetooth Class 2 Module (model number
BM-MP-CS-05) is a small SMT module with
integrated capability of FM radio. This readyto-use Class2 Bluetooth module provides a
fully compliant Bluetooth system V2.0+EDR for
data and voice communications. The EDR
specification provides up to 3Mbits/s
throughput. With its tiny size 6.5x5.7x1.4mm
the module is suitable for smart handheld
devices such as mobile phones and PDA.
To improve the performance of both Bluetooth
and 802.11b/g co-located systems, especially
for handheld devices such as mobile phone
and PDA, the module provides the capability to
support a variety of hardware signalling: 2-wire
activity signalling and 3-wire (IEEE)
coexistence scheme, AFH, and host passing
channel information.
Features
l Fully compliant with Bluetooth v2.0
system
l Enhanced Data Rate(EDR) compliant
for both 2Mbps & 3Mbps modulation
modes
The FM radio can be simultaneously operated
with Bluetooth. It supports both US/Europe
(87.5MHz to 108MHz) and Japanese (76MHz
to 90MHz) FM band. It also supports RDS
(Radio Data System in Europe or Radio
Broadcast Data System in US).
l
With small size suitable for compact
system integration. Low power
consumption, extend the battery life.
Applications
l
Support for 802.11b/g Coexistence:
Channel skipping, AFH, priority
signalling, channel signalling, and host
passing..
l
Superior Performance on mobile
phone band rejection - 150db
l
l
Cellular phones
Personal Digital Assistant
All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI.
Bluetooth+FM Module (BM-MP-CS-05) Preliminary Datasheet
General Description
Features
Standards
Frequency Band
Sensitivity
Output Power
RF Port Impedance
FM Sensitivity
Temperature
Operating Voltage
Power Consumption
Data Rate
Interface
Dimensions
Description
Fully compliant with BluetoothTM 2.0+EDR Standard
2.402GHz ~ 2.480GHz
-83.0 dBm (typ)
0 dBm (typ) with power control (Maxi mum Power measurement is from
chip set)
50+/-10Ohm
-105dbm
Condition: Fmod = 1kHz, Δf = 22.5kHz, (S+N)/N= 26dB, BAF = 300Hz to
15kHz, A-weighted, de-emph = 50μs, fIN = 76 to 108MHz
Operating temperature: -30 °C to +70 °C
Storage temperature: -40 °C to +85 °C
3.3V DC +/- 10%
Basic Data rate:
Asynchronous:723.2kbps/57.6kbps (1x)
Synchronous:433.9kbps/433.9kbps (1x)
Enhance Data Rate:
2Mbps (p/4 DQPSK)
3Mbps (8DPSK)
Asynchronous:723.2kbps/57.6kbps (1x)
Synchronous:433.9kbps/433.9kbps (1x)
38 pin LGA (Land Grid Array)
Length: 6.5 mm, Width: 5.7 mm, Height: 1.4 mm
Recommended Footprint –
(Top View)
All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI.
1
Bluetooth+FM Module (BM-MP-CS-05) Preliminary Datasheet
Pin-assignment
Pin
Name
1
GND
2
FM
3
GND
4
AIO_1
5
I2C_Data
I2C Data
6
I2C_CLK
I2C Clock
7
Sleep-CLK
32.768KHz clock input for watchdog timer
8
AUDIO_R
Right channel output for FM analog output
9
AUDIO_L
Left channel for FM analog output
10
RST#
Reset if low and last at least 5ms
11
GND
Ground
12
UART RX
UART data input, active high
13
UART RTS
UART request to send, active low
14
UART CTS
UART clear to send, active low
15
UART RX
UART data output, active high
16
SPI_PCM#_SEL
17
GND
18
XTAL1
Crystal connection
19
XTAL2
Crystal connection
20
GND
21
VDD_BT
*
22
PCM_SYNC;
23*
PCM_CLK;
SPI_CS#
SPI_CLK
*
24
*
25
Description
Ground
FM receiver input
Ground
Analog input/output line, can be digitally programmed
Control line to select PCM (low) or SPI (high)
Ground
Ground
+3.3V
Synchronous data sync;
Chip select for SPI devices, active low
Synchronous data clock;
SPI clock
PCM_OUT;
Synchronous data output;
SPI_MISO
SPI output
PCM_IN;
Synchronous data input;
SPI_MOSI
SPI input
26
PIO_0
Programmable digital input/output line
27
PIO_1
Programmable digital input/output line
28
PIO_2
Programmable digital input/output line
29
PIO_3
Programmable digital input/output line
30
GND
31
PIO_4
Ground
32
GND
33
RF_OUT
34
GND
35
PIO_5
Programmable digital input/output line
36
PIO_6
Programmable digital input/output line
Programmable digital input/output line
Ground
Bluetooth RF TX/RX
Ground
All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI.
2
Bluetooth+FM Module (BM-MP-CS-05) Preliminary Datasheet
37
PIO_7
Programmable digital input/output line
38
PIO_10
Programmable digital input/output line
*
Note: PCM and SPI interfaces share the same pins. The interface is selected by SPI_PCM#_SEL.
Electrical Characteristics
Absolute Maximum Ratings
Rating
Storage Temperature
Supply Voltage: VDD
Min
Max
-40 °C
-0.40V
+85 °C
+3.60V
Recommended Operating Conditions
Operating Condition
Min
Operating Temperature Range*
-30 °C
Supply Voltage: VDD
+3.0V
Input/Output Terminal Characteristics
Digital Terminals
Min
Max
+70 °C
+3.60V
Typ
Max
Unit
-0.4
0.7VDD
-
+0.4
VDD+0.4
V
V
VDD-0.4
-
0.4
-
V
V
Min
Typ
Max
Unit
VIL input logic level low
VIH input logic level high
0.7VDD
-
0.3VDD
-
V
V
Input leakage current
VSS < VIN< VDD
CI Input capacitance
-1
2.5
1
-
5
10
µA
pF
Output levels to correctly terminated USB
Cable
VOL output logic level low
VOH output logic level high
0
2.8
-
0.2
VDD
V
V
Input Voltage
VIL input logic level low
VIH input logic level high
Output Voltage
VOL output logic level low, (lO = 4.0mA),
VOH output logic level high, (lO = -4.0mA),
USB Terminals
Input threshold
All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI.
3
Bluetooth+FM Module (BM-MP-CS-05) Preliminary Datasheet
For Additional information, please contact the following:
Universal Scientific Industrial Co., Ltd.
Headquarters
141, Lane 351, Taiping Road, Sec. 1, Tsao-Tuen , Taiwan,
Http://www.usi.com.tw
Tel: + 886-49-2350876, 2325876
Fax: +886-49-3439561, 2337360, 2351093
E-mail:usi@ms.usi.com.tw
All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI.
4