BeveLED
3315
DOWNLIGHT
®
Trimless
Innfinite Coloor+
PROJECT INFORMATION
™
PROJECT
DATE
TYPE
1" Regress
™
BeveLED In
nfifinnite Color+ Recessed Trimless Downlight - Illuminate your space with any color available in the spectrum with BeveLED
Infinite Color+. Tune the light from saturated blue, violet, green, yellow, orange, and red, to any of a wide variety of perfect architectural whites with
DMX512 controls. Infinite opportunities abound for hospitality, entertainment, and cultural lighting applications, or any other project requiring full
color and white light flexibility.
1" Regress
1" Regress
Bevel Finish
Color
31⁄2" x 31⁄2"
41⁄2" x 41⁄2"
HOW TO SPECIFY
Ordering Example: Specify trim code and housing code to order: Example : 3315W - B1 - SF - 10 - LSLD4 - 9032 - WRGB1 - 30KS - 60 - NC - 277V - DMX1M - RJ - CB27
TRIM ORDERING INFORMATION
3315
3315
Square
Trimless
Downlight
1" Regress
™
BEVEL STYLE
OPTION
–
______
W
EML
–
Wet location 1
Integral
Emergency
Test Switch 2
B1 1” Regress Bevel,
Painted Die Cast
SF
Wet location, use with
B1 trims only. N/A with
millwork.
In
nfinite Color+ Spectrum
B1 BEVEL FINISH
–
10
13
21
28
RAL
SF Solite Frosted
(provided
standard)
SF Solite Frosted
AB1 1” Regress Bevel,
(provided
Black Anodized Finish
standard)
AC1 1” Regress Bevel,
Clear Matte Anodized Finish
1
2
LENS
White
Statuary Bronze
Black
Metalized Grey
Custom Color
(specify RAL #)
(Leave blank for AB1 and
AC1 Bevel Styles)
Relative Output (W/nm)
TRIM
1
0.8
0.6
0.4
0.2
0
400
450
500
550
600
650
700
750
wavelength (nm)
Independently mix white light with color in any combination
imaginable to create a uniquely personal light source.
Use with NC housing only
HOUSING ORDERING INFORMATION
HOUSING
CODE
WATTAGE
LSLD4 –
LSLD4
9032
9032 32W LED,
1375
Lumen
Maximum
ENGINE
CODE
PRIMARY
WHITE
– WRGB1 –
30KS
WRGB1
30KS 3000K,
80+ CRI
REFLECTOR
–
HOUSING TYPE
–
VOLTAGE
–
NC New Construction
60 60° beam
80 80° beam NCSM1 Narrow Width
1-1/4” ceiling max
NCSM2 Narrow Width
2-1/4” ceiling max
CP Chicago Plenum
IC Insulation-Contact
Rated / Airtight
120V
277V
CABLING
DIMMING DRIVER
–
ACCESSORIES
–
–
RJ RJ45 Jacks
CB27 27” C-Channel Bars
DMX1M EldoLED DMX 0.1%
dimming, manual
WR Splice Connection CB52 52” C-Channel Bars
addressing using
XL XLR5 Connectors 3
EML Emergency battery 4
RDM protocol, 8 bit
EMLW Emergency battery,
DMX2M EldoLED DMX 0.1%
wet location 4
dimming, manual
addressing using
MLXX Millwork adapter 5
RDM protocol, 16 bit
XX=Specify Color
(10, 13, 21, 28, RAL)
Millwork not wet
listed
See emergency solutions
chart for EM options with
these housings
3 Requires above ceiling
access; N/A with IC or CP
housings.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
4
For use with NC housings only.
5
ML not for use with NCSM1
housings.
© 2015. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 09/24/2015
DOWNLIGHT
BeveLED Innfinite Coloor+ Trimless
™
3315
TRIM INFORMATION
3315 Emergency Solutions
EM
Integral
Remote
Inverter
Housing
SERVICE
Test Switch Test Switch By Others
NCSM*
N/A
X
NC
Through aperture
X
NC Wet Location Through aperture
X
CP
N/A
X
IC
N/A
X
1" Regress
31⁄2" x 31⁄2"
EM fixtures that are
provided with an integral
test switch are shipped
with a hole in the
glass lens for access.
Refer to “EMERGENCY
SOLUTIONS” chart to find
out which fixtures have an
integral test switch.
41⁄2" x 41⁄2"
HOUSING INFORMATION
New Construction
Universal Style Housing - NC
Chicago Plenum - CP
IC / Airtight - IC
73/8"
81/2"
/8"-1"
5
7"
/8"-1"
5
7"
13"
13"
185/8" (Plan View)
185/8" (Plan View)
22 /8" (Plan View)
221/8" (Plan View)
1
83/8"
New Construction - Narrow Width
53/4"
43/4"
X"
NCSM1: 5/8" - 11/4"
NCSM2:11/4" - 21/4"
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
19" (Plan View)
22(Plan View)
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2015. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 09/24/2015
DOWNLIGHT
BeveLED Innfinite Coloor+ Trimless
™
3315
SPECIFICATIONS
TRIM: 4-1/2" square aperture with a 1" regressed bevel
retained by two mounting clips. Die cast aluminum bevel
is available in white, statuary bronze, black, and metalized
grey finishes. Also available in black or clear matte bevel,
with painted flange. Custom color flanges available (provide
RAL#).
CABLING: The DMX512 driver is provided with two twisted
pair cabling for connection with communication controls.
Data cables must be run in series between fixtures. Choose
your preferred method of connection when specifying. To
avoid signal transmission problems, a DMX link terminator
should be used in the last fixture in a series. NOTE:
Communication cables and AC power lines must not be run
TRIM LENS: Trim is shipped with integral frosted solite lens
in the same conduit.
standard.
• RJ Cabling Option: fixture is provided with a DMX512
REFLECTOR: Interchangeable precision injection molded
interface board inside the junction box with RJ45 jacks for
reflector optimized for 60° or 80° beam distribution.
use with CAT5 cable terminated with RJ45 connectors.
For USAI Lighting fixtures with RJ45/CAT5 connections,
FIELD REPLACEABLE LIGHT ENGINE: Available in 1 lumen
the following ANSI/TIA/EIA-568 pin out standard is used.
package: typical power draw is 23 input watts with 1150
Link termination dip switch is provided at the connector
delivered lumens. Maximum power draw is 32 input watts
with up to 1375 delivered lumens. Engine is field replaceable board; no separate link termination device is required. See
dimming compatibility pages for drawings and more details
through the aperture without tools.
on this configuration.
COLOR: BeveLED Infinite Color+ is capable of creating
any color desired in the spectrum, from saturated blue,
violet, green, yellow, orange, and red, to a wide variety of
architectural whites. All color change is digitally controlled
through the DMX interface of your choice.
RATED LIFE: Based on IESNA LM80-2008 50,000 hours at
70% lumen maintenance (L70).
THERMAL MANAGEMENT: Proprietary high performance
aluminum die cast heatsink for maximum LED life. Ambient
temperatures at fixture location should not exceed 40°C
during normal operation.
• WR Cabling Option: no interface board is supplied; cables
must be spliced inside the junction box for connection. The
data cable used must meet the following requirements:
• type: shielded, 2-conductor twisted pair
• maximum capacitance between conductors: 30 pF/ft
FIELD REPLACEABLE DIMMING DRIVER: Solid state
• maximum capacitance between conductor and
electronic constant current DMX512 8-bit driver with a
shield: 55 pF/ft
high power factor provided standard. Specify 120V or 277V.
• maximum resistance: 0.02 ohms/ft
Driver complies with IEEE C62.41 surge protection. Specify
• normal impedance: 100-140 ohms
DXM1M for 8-bit communication controls; specify DMX2M
• conductive core: 24 AWG is recommended
for 16-bit communication controls. All driver options require
remote device management (RDM) communication protocol If 3-wire data cables are preferred, we suggest a Belden
for addressing.
9841 or equivalent cable which meets the specifications for
EIA RS-485 applications. Do not use standard microphone
cables: they cannot transmit DMX512 data reliably over
long distances. NOTE: DMX link termination device (by
others) should be used on last fixture in line on a circuit to
avoid signal loss.
EMERGENCY: Fixtures provided with an integral
test switch are provided with a hole in the glass
lens as per the drawing above. Fixtures provided
with a remote test switch are provided with a 24”
lead length for location of the test switch. Fixtures
that have no USAI EM option may be connected to
an inverter (by others) for emergency lighting. See
emergency solutions chart for more information on
EM test switches and servicing.
MOUNTING: Butterfly brackets and adjustable
nailer bars with integral nails provided. Nailer bars
are extendible from 14” to 24” centers.
HOUSING: All-Ways Square® (covered by US
Pat. No: US 7,832,889) housing allows alignment of
square aperture (up to 20° rotation) after housing
installation and prior to finish ceiling installation.
Fabricated of 20 ga. galvanized steel with thru wire
J-box, 4 in 4 out at min. 90°C, #12 AWG thru branch
circuit wiring. NCSM housing can NOT be used with
thru-branch circuit wiring.
MAXIMUM CEILING THICKNESS: As per drawings
above.
CEILING CUT OUT: Millwork: 4-13/16” x 4-13/16”
All others: 5-1/2” x 5-1/2”
LISTINGS: Dry/Damp. Wet location option available
with B1 trim only. Millwork is not wet listed. NRTL/
CSA-US tested to UL standards. IBEW union made.
WARRANTY: 5 years
NOTES:
• Not for use in corrosive environment.
• Use of pressure washer voids warranty.
• Not for use in acoustical ceiling tiles.
PHOTOMETRICS: Consult factory or website for IES
files. Tested in accordance with IESNA LM79-2008.
• XL Cabling Option: fixture is provided with a DMX512
interface board on the junction box with standard 5-pin
XLR5 jacks which accept XLR5 connectors for DMX
communication. Any standard XLR cable can be used for
this option. Link termination dip switch is provided at the
connector board; no separate link termination device is
required. NOTE: This cabling option requires above ceiling
access.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2015. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 09/24/2015
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DMX1M, DMX2M
®
BeveLED Innfinite Coloor+
™
DIMMING DRIVER WIRING SCHEMES:
DMX1M: EldoLED DMX dimming with manual addressing, 8-bit (Dims down to 0%)
DMX2M: EldoLED DMX dimming with manual addressing, 16-bit (Dims down to 0%)
Choose from WR (splice connection), RJ (RJ45 jacks) and XL (XLR5 connectors) cabling options,
and refer to corresponding wiring diagram below:
4 BLUE
3
DMX (-)
GREEN/ WHITE
2 ORANGE
DMX (+) 1
BLUE / WHITE
5
GREEN
6
BROWN / WHITE
7
ORANGE/WHITE
BROWN
8 SHIELD
CAT 5 CABLE
RJ CABLING OPTION
RJ-45 CONNECTORS
DMX DATA IN
DMX DATA OUT
ON
DMX+
ON
DMXSHIELD
TURN ON DIP SWITCH
TO TERMINATE LAST
FIXTURE ON DMX BUS
OFF
OFF
LOAD
LINE
V+
DRIVER
NEUTRAL
V-
GROUND
WR OPTION
DMX DATA IN
DMX DATA OUT
DMX+ BLUE
DMX+
DMX- WHITE
DMX-
SHIELD-
SHIELD
• WR Cabling Option: no interface board is supplied; cables
must be spliced inside the junction box for connection. The
data cable used must meet the following requirements:
• type: shielded, 2-conductor twisted pair
• maximum capacitance between conductors: 30 pF/ft
• maximum capacitance between conductor and
shield: 55 pF/ft
• maximum resistance: 0.02 ohms/ft
• normal impedance: 100-140 ohms
• conductive core: 24 AWG is recommended
LOAD
DRIVER
LINE
NEUTRAL
V+
V+
V-
V-
If 3-wire data cables are preferred, we suggest a Belden
9841 or equivalent cable which meets the specifications for
EIA RS-485 applications. Do not use standard microphone
cables: they cannot transmit DMX512 data reliably over
long distances. NOTE: DMX link termination device (by
others) should be used on last fixture in line on a circuit to
avoid signal loss.
GROUND
XL CABLING OPTION
NOTE: This cabling option requires above ceiling access.
4.75"
XLR CABLE
5 PIN XLR CONNECTORS
MALE FEMALE
DMX DATA IN
1.-10"
DMX DATA OUT
XLR CONNECTORS WHEN XLR5 IS
SELECTED LEAVE CLEARANCE FOR
J-BOX TO SLIDE TO APERTURE
Off
DMX+
On
DMX-
Termination
1-1/8"
SHIELD
TERMINATION
LOAD
TURN ON DIP
SWITCH TO
TERMINATE
LAST FIXTURE
ON DMX BUS
V+
LINE
DRIVER
NEUTRAL
V-
GROUND
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2014. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-265
®
BeveLED Innfinite Coloor+
™
DIMMING DRIVER WIRING SCHEMES:
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DMX1M, DMX2M
DMX MUST BE DAISY CHAINED IN SINGLE LINE
CORRECT !
INCORRECT !
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
NOTES FOR DRIVERS:
1. DMX signal cable must NOT be run in same conduit as high voltage AC power lines.
2. Fixtures must be daisy chained in one serial line using Data in and Data out
3. Maximum of 32 DMX devices on a single DMX bus
4. Maximum of 1600 ft serial communication link distance
5. To avoid signal loss, DMX signal terminator should be used on last fixture in line. For RJ
and XL cabling options, this is provided through a dip-switch on the connector board. For
WR cabling options, this device (120 ohm resistor) is provided by others.
6. For best results when using WR cabling option use communication data splices.
7. Default state for fixtures off. Luminaire will not light until DMX signal is received.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2014. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-265