Shenzhen HAC Telecom Technology Co., Ltd
HAC-ADSB Manual
V1.00
I. Using Method of HAC-ADSB (Tag)
1. Dimension of HAC-ADSB (Tag) www.rf-module-china.com
TEL: +86-755-23981078
Shenzhen HAC Telecom Technology Co., Ltd
2. Working mode of HAC-ADSB : (Tag)
1).The ex-factory state of HAC-ADSB is sleeping state, it does not send wireless signal, it is low power-consumption. It is convenient for transportation and stock.
2). Press the ‘Start’ button for 3s, the tag starts and enters into working mode, it will send ID information every 4s, and the working time is less than 1.5ms, the rest time is sleeping. The red LED will flicker once for every data transmission. The sending interval can be set by users. The temperature sampling period is 2mins per time.
3) During the working time or after power on, press ‘Start’ button for 3s AGAIN, the tag will enter into setting mode. Users can change the ID, sending interval, RV1, RV2. After finishing setting, it will exit the setting mode immediately. If there is no setting within
30s, it will exit the setting mode automatically.
II. Using Method of HAC-ADM
1. Dimension of HAC-ADM www.rf-module-china.com
TEL: +86-755-23981078
Shenzhen HAC Telecom Technology Co., Ltd
2. Pin Definition of HAC-ADM
PIN DEFINATION Input/Output description
1 VCC In power , 3.0~3.6V
2 TXD Out Serial data output
3
5
RXD
RESET
In
In
Serial data input
Low level reset
10 GND
Do not need connect other pins ground
3. Antenna
1 ) PCB antenna 2 ) whip antenna 3 ) external antenna
4. HAC-ADM-MU can use USB port to charge. On the same time, it will transfer USB port to a virtual serial port. You need to install the driver of USB to virtual serial port. The driver software is: PL2303_Prolific_DriverInstaller_v130.exe.
You can refer to
PL2303_Prolific_DriverInstaller_v130_releasenote.txt
to know more about how to install the
USB to serial port driver. www.rf-module-china.com
TEL: +86-755-23981078
Shenzhen HAC Telecom Technology Co., Ltd
After the installation, the device manager of PC will add a new serial port, and then you can use ScomAssistant to receive the information send from the RFID . (please install the
Terminal.exe for ScomAssistant). Serial port: 38400bps, 8N1
III. Serial Data Protocol
Serial port output:
The serial port of HAC-ADM-MU (The receiver) outputs the information of HAC-ADSB
(the tag) with 38400bps & 8N1 data format. The protocol of information is shown as following (Hex):
24 UID1 UID0 ID3 ID2 ID1 ID0 S V RV1 RV2 TMP1 TMP2 TS RSSI CS
24: Frame head
UID1 UID0: C ategory ID number
ID3 ID2 ID1 ID0 : ID number of HAC-ADSB
S : Reservation
V : Voltage of battery
VCC= (BV/256)*3.45
, if the battery is lower than 2.5V, it is under-voltage.
RV1: Setting word by Users, default value: 00
RV2: Setting word by Users, default value: 00
TMP1: High-byte for temperature data
TMP2: Low-byte for temperature data
Temperature = ( (TMP1<<8|TMP2)-500 ) /10
TS: Serial number of transmitting
RSSI: The strength of transmitting signal, dBm with symbol
CS: The low byte of the previous data check sum www.rf-module-china.com
TEL: +86-755-23981078
Shenzhen HAC Telecom Technology Co., Ltd
Input protocol for serial port setting command (Hex):
26 ID3 ID2 ID1 ID0 TPN ID_3 ID_2 ID_1 ID_0 CS
26: Frame head
ID3 ID2 ID1 ID0: ID of HAC-ADSB
TPN=0xFF: Close wireless
TPN=0x02: Change Sending interval ID_0 effective ( 1s~256s )
TPN=0x03: Change RV1, RV2 ID_1, ID_0 effective
CS: The low byte of the previous data check sum
IV. Technical Specs
Modulation : QPSK
Spread spectrum : DSSS
Working frequency: 2.475GHz
Transmitting power: 4dBm
Receiving sensitivity: -97 dBm
Bandwidth of channel: 2MHz
Working temperature: -40 ℃~ 80 ℃
Life time: 5 years
Transmitting distance: 100 meters www.rf-module-china.com
TEL: +86-755-23981078