Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16955 Rev A
SECTION 28 23 29
HDZ SERIES ANALOGUE TRUE DAY/NIGHT INDOOR/OUTDOOR HIGH SPEED PTZ CAMERA
PART 1 GENERAL
1.1
SECTION INCLUDES
A.
1.2
Provide a true day/night analogue indoor/outdoor high speed PTZ dome camera with 30x or
36x zoom lens for video surveillance; including design, supply, installation and
commissioning.
RELATED SECTIONS
NOTE TO SPECIFIER: Include related sections as appropriate if video surveillance system is integrated
to other systems.
1.3
A.
Section 26 05 00 – Common Work Results for Electrical, for interface and coordination with
building electrical systems and distribution.
B.
Section 28 05 13 – Conductors and Cables for Electronic Safety and Security, for cabling
between system servers, panels, and remote devices.
C.
Section 28 05 28 – Pathways for Electronic Safety and Security, for conduit and raceway
requirements.
D.
Section 28 23 00 – Video Surveillance Equipment, for interface with, and administration of
video recording devices and equipment.
E.
Section 28 23 23 – Video Surveillance Systems Infrastructure.
F.
Section 28 23 29 – Video Surveillance Remote Devices and Sensors.
REFERENCES
A.
Reference Standards: Provide systems that meet or exceed the requirements of the
following publications and organizations as applicable to the work of this Section:
1.
Canadian ICES-003
2.
Canadian Standards Association (CSA)
3.
Conformity for Europe (CE)
4.
Federal Communications Commission (FCC)
5.
Joint Photographic Experts Group (JPEG)
28 23 29-1
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
1.4
National Television Systems Committee (NTSC)
7.
Phase Alternating Line (PAL)
8.
Underwriters Laboratories Inc. (UL)
9.
IP Code (Ingress Protection Rating) per IEC 60529
SYSTEM DESCRIPTION
A.
B.
1.5
6.
Guide Specifications in CSI Format
800-16955 Rev A
The HDZ Series analogue indoor/outdoor PTZ dome camera shall use either:
1.
A flexible indoor enclosure that can be mounted quickly to a flat surface with one of
the mounting options, easily installed with the in-ceiling mounting bracket, wall mount
or pendant mount.
2.
A rugged, discreet, outdoor NEMA 4X and IP66-rated vandal-resistant enclosure that
can be easily installed directly to a ceiling, wall or roof with either the wall, ceiling or
parapet mounting accessories.
The HDZ Series analogue indoor/outdoor True Day/Night PTZ dome camera shall capture
video in 650 TVL horizontal resolution for clean, sharp images at 30 frames per second
(NTSC) and 25 frames per second (PAL). As a True Day/Night solution, the analogue PTZ
dome camera has a low light sensitivity of 0.08 lux (color) / 0.005 lux (B/W). The camera is
designed for a broad range of surveillance applications and features real-time wide dynamic
range to accommodate a wide variety of surveillance environments.
SUBMITTALS
A.
General: Submittals shall be made in accordance with the Conditions of the Contract and
Submittal Procedure Section.
B.
Manufacturer’s Product Data: Submit manufacturer’s data sheets indicating systems and
components proposed for use, including instruction manuals.
C.
Shop Drawings: Submit complete shop drawings including connection diagrams for
interfacing equipment, list of connected equipment, and locations for major equipment
components.
D.
Record Drawings: During construction maintain record drawings indicating location of
equipment and wiring. Submit an electronic version of record drawings not later than
Substantial Completion of the project.
E.
Operation and Maintenance Data: Submit manufacturer’s operation and maintenance data,
customized to the system installed. Include system and operator manuals.
F.
Field Tests: Submit results of field testing of every device including date, testing personnel,
retesting date (if applicable), and confirmation that every device passed field testing.
G.
Maintenance Service Agreement: Submit a sample copy of the manufacturer’s maintenance
service agreement, including cost and services for a one year period for Owner’s review.
Maintenance shall include, but not be limited to, labor and materials to repair the system,
tests and adjustments, and regular inspections.
28 23 29-2
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
1.6
QUALITY ASSURANCE
A.
Manufacturer: Minimum ten years experience in manufacturing and maintaining video
surveillance systems. Manufacturer shall provide toll-free technical assistance and support
available 24/7.
B.
Manufacture Location: Provide equipment assembled in Taiwan.
C.
Installer: Minimum two years experience installing similar systems, and acceptable to the
manufacturer of the video surveillance system.
D.
Regulatory Requirements:
1.
E.
F.
1.
Indoor pendant dome operating temperatures shall be between 0°C (32°F) and 50°C
(122°F).
2.
Outdoor pendant dome operating temperatures shall be between −40°C (−40°F) and
50°C (122°F).
Power Requirements:
2.
Indoor in-ceiling and pendant dome:
a.
Input Voltage: 24 V AC ±10%, 50/60 Hz.
b.
Power Consumption: 20 W maximum.
Outdoor pendant and vandal-resistant rugged dome:
a.
Input Voltage: 24 V AC ±10%, 50/60 Hz.
b.
Power Consumption: 50 W maximum (with heater/blower).
DELIVERY, STORAGE, AND HANDLING
A.
1.8
Emissions: EU – EN61000-6-3; NA - FCC Part 15B, ICES-003.
Environmental Requirements (protecting the dome from direct sunlight in high temperature
environments is advised):
1.
1.7
Guide Specifications in CSI Format
800-16955 Rev A
Deliver materials in manufacturer’s labeled packages. Store and handle in accordance with
manufacturer’s requirements, in a facility with environmental conditions within recommended
limits.
WARRANTY
A.
Manufacturer’s Warranty: Submit manufacturer’s warranty of three (3) years from the
manufacture date code under normal use and service for the video surveillance system.
28 23 29-3
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16955 Rev A
PART 2 PRODUCTS
2.1
2.2
MANUFACTURER
A.
HDZ Series Camera Manufacturer: Honeywell HDZ Series analogue true day/night
indoor/outdoor PTZ dome camera, www.honeywell.com/security or
www.honeywellintegrated.com.
B.
Accepted Part Numbers:
HDZ30A – PTZ Analogue Dome, Indoor Pendant, 30x TDN NTSC, Clear Dome
2.
HDZ36AE – PTZ Analogue Dome, Outdoor Pendant, 36x TDN NTSC, Clear Dome
3.
HDZ30AX – PTZ Analogue Dome, Indoor Pendant, 30x TDN PAL, Clear Dome
4.
HDZ36AEX – PTZ Analogue Dome, Outdoor Pendant, 36x TDN PAL, Clear Dome
SYSTEM COMPONENTS
A.
2.3
1.
Indoor/Outdoor dome housing, camera scan unit, cabling, and an OSD menu that provides
complete control of the PTZ dome settings.
OPERATIONAL REQUIREMENTS
A.
The HDZ Series analogue true day/night indoor/outdoor PTZ dome camera system shall
meet or exceed the following camera specifications:
1.
Image Sensor: 1/4-inch Sony CCD
2.
Horizontal Resolution: 650 TVL
3.
Optical Zoom:
4.
a.
HDZ30A(X): 30x
b.
HDZ36AE(X): 36x
Focal Length:
a.
HDZ30A(X): 3.4–102.0 mm
b.
HDZ36AE(X): 3.4–122.4 mm
5.
Focus Mode: Auto/Manual
6.
Iris Control: Auto/Manual
7.
Minimum Illumination: 0.08 lux (color) / 0.005 lux (B/W) @ F1.6 (30 IRE)
8.
Shutter Speed: 1/1–1/10,000 seconds
9.
White Balance: Auto/Manual
10.
Signal-to-Noise Ratio: greater than 50 dB (AGC off)
28 23 29-4
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16955 Rev A
11.
Backlight Compensation: On/Off
12.
AGC: Auto/Manual (Max gain limit settings for Full Auto, Shutter Priority, and Iris
Priority modes)
B.
The HDZ Series analogue PTZ camera must be available with a 650 TVL super highresolution color/monochrome (true day/night) and wide dynamic range (WDR) advanced
digital signal processing (DSP) camera and a 30X optical zoom (3.4 mm to 102.0 mm) or
36X optical zoom (3.4 mm to 122.4 mm).
C.
The HDZ Series analogue PTZ wide dynamic range (WDR) and color/monochrome (true
day/night) camera shall utilize a 1/4" Sony CCD technology with a minimum horizontal
resolution of 650 TVL. The camera must provide sharp, detailed images down to 0.08 lux
color, and 0.005 lux monochrome. When switching to monochrome mode, the camera must
automatically remove the IR cut filter when necessary, which will increase the infrared
sensitivity. When enough ambient light is available to produce an acceptable color image,
the camera must automatically enable the IR cut filter. The camera must also utilize WDR
technology, allowing for detail to be captured accurately even in high contrast scenes.
D.
The HDZ Series analogue PTZ camera shall support video connection through BNC or UTP
cable. An optional UTP balun is included with the unit, if UTP video connection is required.
E.
The fully featured HDZ Series analogue PTZ camera supports the following built-in
Protocols:
1.
Maxpro Mode (default), baud rate 9600, parity even
2.
VCL, baud rate 9600, parity none
3.
Pelco D, baud rates 2400, 4800, or 9600, parity none
4.
Pelco P, baud rates 2400, 4800, or 9600, parity none
F.
The HDZ Series analogue PTZ camera shall be comprised of a high-speed pan/tilt assembly
using precision stepper motors with a high-strength belt drive, resulting in quiet and accurate
operation.
G.
The HDZ Series analogue PTZ camera shall transmit images with 480K effective pixels
(NTSC) or 570K effective pixels (PAL) at 30 frames per second (NTSC) and 25 frames per
second (PAL).
H.
The HDZ Series analogue PTZ camera shall include, as standard, an OSD menu that
provides complete control of the PTZ dome settings. The OSD menu shall be available
through a connected monitor and keyboard/controller.
I.
The HDZ Series analogue PTZ camera shall feature OSD menus for programming dome
parameters. A minimum of the following menus must be available:
1.
Language
a.
English
b.
Czech
c.
German
d.
Spanish
28 23 29-5
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
2.
3.
4.
e.
French
f.
Italian
g.
Portuguese
h.
Russian
i.
Simple Chinese
j.
Traditional Chinese
k.
Dutch
l.
Polish
m.
Turkish
n.
Japanese
Guide Specifications in CSI Format
800-16955 Rev A
Display Options
a.
ID Display
b.
Pan azimuth and the tilt elevation display (PT Position display)
c.
Zoom Msg.
d.
Title Display
e.
Title Zone Display
f.
Time and Date Display
Diagnostic Options
a.
Restore Default Settings
b.
System Reset
Camera Options
a.
Zoom and Focus
b.
Exposure Control
c.
White Balance
d.
Backlight
e.
Flip – Mechanical/Image/Off
f.
Image Inverse
g.
Speed by zoom
h.
WDR
i.
2D NR/3D NR
j.
Auto Calibration
28 23 29-6
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
k.
5.
J.
Guide Specifications in CSI Format
800-16955 Rev A
Motion Detection
Function Programming
a.
Program Alarms
b.
Program a Mimic tour
c.
Program a Preset position
d.
Program a Preset tour
e.
Program a Auto pan
f.
Program Privacy zone
g.
Program Home
The HDZ Series analogue PTZ camera shall include, as standard, the following PTZ
features and functions:
1.
Manual pan speeds must range from 0.5º to 200º per second, and manual tilt speeds
must range from 0.5º to 84º per second.
2.
Provides for three (3) auto focus modes: PTZ trigger focus, Zoom trigger focus, and
Continuous auto focus. When the scene requires extra-fine control, the dome must
allow the operator to override the auto focus settings. Auto iris with manual override
must also be standard.
3.
Sixteen (16) mimic or learned tours. The user shall perform a series of pan, tilt, zoom
movements that the dome must “learn”. When the pattern is recalled, the dome
automatically repeats the movements. The duration of each mimic tour can be up to
one hundred (100) seconds.
4.
Support for up to sixteen (16) programmable preset tours, each with up to thirty-two
(32) preprogrammed positions. Each position can include a preset position, the speed,
and the dwell time (dwell time defines the time the dome rests before going to the next
preset position). The tour can be programmed to run continuously until halted by the
operator.
5.
In order to quickly identify the specific PTZ an operator is viewing, the HDZ Series
analogue PTZ camera shall contain title display and ID display options to display the
camera information on-screen.
6.
Sixteen (16) programmable Dynamic Privacy Zones to block sensitive areas from
viewing/recording.
7.
Incorporates flash memory to protect the programming for the privacy zones if power
is lost. The flash memory shall retain the programming for a minimum of twenty (20)
years. If the privacy zones have been programmed and the unit loses power, the
video will remain blank until the PTZ dome finds its index position to prevent any area
behind programmed privacy zones from being visible when power is restored.
8.
Supports auto-homing to activate a preset tour, mimic tour, or a preset position after a
specified period of inactivity, programmable from one (1) to one hundred and twentyeight (128) minutes.
28 23 29-7
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
2.4
Guide Specifications in CSI Format
800-16955 Rev A
9.
Able to display the pan azimuth and the tilt elevation/declination, in degrees, on the
video. Users must have the ability to turn the coordinates on or off.
10.
Displays date and time in the video for viewing/recording. Users must have the ability
to turn it on/off. The HDZ analogue PTZ Series shall allow users to enter an
alphanumeric camera ID/name and insert the ID/name in to the video for viewing on a
monitor (add text overlay on video). In addition, a digital zoom label shall be available
on the video to display the current digital zoom magnification when zoom in/out. Users
must have the ability to turn both IDs/names on or off.
K.
The HDZ Series analogue PTZ camera must provide the option of restoring all displays,
alarms, camera settings, and diagnostic settings to factory default with an OSD menu
command or a camera board factory reset button.
L.
The HDZ Series analogue PTZ camera shall include four (4) on-board alarm inputs for
normally open or normally closed dry contacts. The dome shall have the ability to go to a
preset position, start a preset tour, start an autopan line, or start a mimic tour when an alarm
occurs. The dome must insert “A” and the alarm pin number to the video signal display for
viewing on the monitor until the alarm returns to its normal state. When more than one alarm
occurs, the latest alarm will be performed.
M.
The HDZ Series analogue PTZ camera shall include two (2) on-board alarm outputs for
normally open or normally closed dry contacts. The dome shall have the ability to perform
the relay out signal to the alarm equipment.
N.
The HDZ Series analogue PTZ camera shall be available in indoor configurations designed
for installation of in-ceiling bracket and pendant mount configurations. The bottom domes
must be designed to blend in with building aesthetics and shall be constructed of vacuumformed, optically-graded acrylic available in smoke and clear finishes. Trim rings must be
available in white finishes.
O.
The HDZ Series analogue PTZ camera shall be available in a pendant housing specifically
designed for installation in an outdoor environment, with an integral resistive type
thermostat-controlled 24 V AC heater and blower to maintain a sufficient operating
temperature. The pendant housing shall be IP66 rated. The bottom domes shall be designed
to blend in with building aesthetics and shall be constructed of vacuum-formed, opticallygraded acrylic available in smoke and clear finishes. Available mounting options shall
include pendant, wall, roof, and parapet, as well as pole and corner adapters.
P.
The HDZ Series analogue PTZ camera shall be available with Vandal Proof Acrylic/bubble
for indoor or outdoor environments with tamper-resistant screws. The Acrylic/bubble shall be
designed to blend in with building aesthetics and shall be constructed of optically-graded
acrylic available in smoke and clear finishes. The unit shall have an Industry standard 1.5"
NPT connections that shall work with all existing Honeywell PTZ mounts and brackets. The
PTZ dome should be protected from direct sunlight in hot climates.
HDZ SERIES INTEGRATIONS
A.
The following mounting options are compatible with the HDZ Series analogue PTZ camera:
1.
HDZINBKT – In-Ceiling Bracket for HDZ Series
2.
HDVWM1 – Indoor Only Wall Mount
28 23 29-8
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
B.
C.
2.5
Guide Specifications in CSI Format
800-16955 Rev A
3.
HDXWM2 – Indoor and Outdoor Wall Mount
4.
HDXSM1 – Half Swan Neck Pole Mount
5.
HDPRM2 – Parapet and Roof Mount
6.
HDCM1 – Ceiling Mount for Indoor Pendant (Not for outdoor use)
7.
HDXPMA2 – Pole Mount Adapter for HDXWM2
8.
HDXCMA1 – Corner Mount Adapter for HDXWM2
The following optional accessories are compatible with the HDZ Series analogue PTZ
camera:
1.
HDZVRSMKAC – Smoked Polycarbonate Vandal Proof Acrylic for HDZ Series
2.
HDZVRCLRAC – Clear Polycarbonate Vandal Proof Acrylic for HDZ Series (repair
purposes only)
3.
HDZIK10AC – Clear IK10 Vandal Proof Acrylic for HDZ Series
4.
517082-7130 – In-Ceiling PTZ Support Plate
The following recorders and devices are compatible with the HDZ Series Analogue PTZ
camera:
1.
MAXPRO® NVR Hybrid XE, SE, PE – Entry to Enterprise Level Hybrid Network Video
Recorders
2.
Fusion Hybrid DVR – Full-featured Hybrid Digital Video Recorder
3.
HVE Encoders – Network Audio/Video Encoder
4.
Rapid Eye – 4, 8, and 16 Channel Hybrid Digital Video Recorder
5.
HRDP – Digital Video Recorder
6.
HREP II – Digital Video Recorder
7.
HVBPIT44 – Protocol Translator
8.
HVBGPIO – Protocol Translator
9.
MegaPIT – Protocol Interface Translator
10.
HJC4000 – UltraKey Touch Keyboard/Controller
SYSTEM HARDWARE
A.
The HDZ Series analogue PTZ camera shall have the following mechanical specifications:
1.
Indoor unit using the In-Ceiling bracket:
a.
Unit Dimensions (H x Dia.): 9.1" x 10.0" (231.5 mm x 254.0 mm)
b.
Unit Weight: 6.83 lb (3.1 kg)
c.
Lower Dome Diameter: 5.8" (148.0 mm)
28 23 29-9
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
2.
3.
B.
Indoor Pendant unit:
a.
Unit Dimensions (H x Dia.): 10.8" x 7.5" (275.1 mm x 191.5 mm)
b.
Unit Weight: 4.85 lb (2.2 kg)
c.
Lower Dome Diameter: 7.5" (191.5 mm)
Outdoor Pendant unit:
a.
Unit Dimensions (H x Dia.): 10.7" x 7.5" (270.5 mm x 191.5 mm)
b.
Unit Weight: 5.73 lb (2.6 kg)
c.
Lower Dome Diameter: 7.5" (191.5 mm)
The HDZ Series analogue PTZ camera shall have the following electrical specifications:
1.
2.
C.
Indoor In-Ceiling and Indoor Pendant dome:
a.
Input Voltage: 24 V AC ±10%, 50/60 Hz
b.
Power Consumption: 20 W maximum
Outdoor Pendant and Vandal-Resistant Rugged dome:
a.
Input Voltage: 24 V AC ±10%, 50/60 Hz
b.
Power Consumption: 50 W maximum (with heater/blower)
The HDZ Series analogue PTZ camera shall be designed to meet the following
environmental conditions:
1.
Indoor In-Ceiling and Indoor Pendant dome:
a.
2.
Operating Temperature: 32°F to 122°F (0°C to 50°C)
Outdoor Pendant and Vandal-Resistant Rugged dome:
a.
2.6
Guide Specifications in CSI Format
800-16955 Rev A
Operating Temperature: –40°F to 122°F (–40°C to 50°C)
3.
Relative Humidity: 10%-90%, non-condensing
4.
Emissions: EU – EN61000-6-3; NA - FCC Part 15B, ICES-003
5.
Immunity: CE - EN50130-4
6.
Safety: EU - EN60950-1, EN60950-22
NA – UL/CSA 60950-1, UL/CSA 60950-22
MANUFACTURER SUPPORT
A.
Manufacturer shall provide customer service, pre-sales applications assistance, after-sales
technical assistance, access to online technical support, and online training using Web
conferencing.
B.
Manufacturer shall provide 24/7 technical assistance and support by means of a toll-free
telephone number at no extra charge.
28 23 29-10
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16955 Rev A
PART 3 EXECUTION
3.1
EXAMINATION
A.
3.2
3.3
INSTALLATION
A.
All components of the camera system shall be thoroughly tested before shipping to the
project location.
B.
Camera system shall be installed, programmed, and tested in accordance with
manufacturer’s installation instructions.
1.
Coordinate interfaces with Owner’s representative where appropriate.
2.
Provide conduit, cable and wire for a complete and reliable installation. Obtain
Owner’s approval for exact location of the camera and all boxes, conduit, cable, and
wiring runs prior to installation.
3.
Install conduit, cable, and wire parallel and square with building lines, including raised
floors areas. Do not exceed forty percent (40%) fill in conduits. Gather wires and tie to
create an orderly installation.
4.
Coordinate with other trades to provide proper sequencing of installation.
FIELD COMMISSIONING AND CERTIFICATION
A.
3.4
Examine site conditions prior to installation. Notify Architect and Owner in writing if
unsuitable conditions are encountered. Do not start installation until site conditions are
acceptable.
Field Commissioning: Test dome camera system as recommended by manufacturer,
including the following:
1.
Conduct complete inspection and testing of equipment, including verification of
operation with connected equipment.
2.
Test devices and demonstrate operational features for Owner’s representative and
authorities having jurisdiction, as applicable.
3.
Correct deficiencies until satisfactory results are obtained.
4.
Submit written copies of test results.
TRAINING
A.
Conduct on-site system administrator and security/surveillance operator training, with the
number of sessions and length of sessions as recommended by the video surveillance
28 23 29-11
Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera
www.honeywell.com/security
Guide Specifications in CSI Format
800-16955 Rev A
system manufacturer. Training shall include, but not limited to camera administration,
provisioning, configuration, operation, and diagnostics.
END OF SECTION
28 23 29-12