Name …………………………………………….
CCNA2 EOC2 Revision Guide
1. What command will take you into privileged EXEC mode from user EXEC
mode?
Router>privileged
Router#privileged
Router>enable
Router#enable
Router>edit
Router#edit
2
2. What actions will return you to the privileged EXEC mode from the interface
configuration mode? (Choose 2)
The command end
The command exit
The command stop
The keystrokes Ctrl-X
The keystrokes Ctrl-Z
The keystrokes Esc
2
3. Which CLI session cannot be used for initial configuration?
Console
AUX
Telnet
All of the above
None of the above
2
4.
(C2600–G40–FZ)
From the above show version screenshot, what can be deduced about the
IOS? (Select 4)
The platform is C2600
The platform is G40
The features include 40bit encryption
The features include managed modems
The image runs in ROM
The image runs in Flash
The image is compressed
dgooch
1
4
CCNA2 EOC2 Revision Guide
5. How can you repeat the previous command entry at the CLI? (Choose 2)
Press Enter
Press the up arrow key
Press Ctrl-P
Press Ctrl-Z
Press Esc
Press Tab
2
6. Which of the following is the global configuration mode?
Router>
Router#
Router#(config)
Router#(config-if)
2
7. During initial setup what is the purpose of the letter(s) in square brackets at the
CLI?
It is the default answer if the Enter key is pressed.
It indicates what you must type into the CLI
It is an abbreviation of an IOS command
It serves no purpose
2
8. During router initialization, Bootstrap – Load IOS – Load Configuration, what
might happen if no configuration file is found in NVRAM? (Choose 2)
Configuration file is loaded from TFTP server
Configuration file is loaded from Flash
Configuration file is loaded from RAM
Configuration file is loaded from ROM
Router enters initial configuration mode
Router initialization fails
2
9. What happens if the backup configuration file is deleted and the router
reloaded?
The router reboots in ROM monitor mode
The router ceases to function
The router enters user EXEC mode
The router enters initial configuration mode
The router enters privileged EXEC mode
The router enters Boot ROM mode
The router operates normally
dgooch
2
CCNA2 EOC2 Revision Guide
2
10. What does the command cl? return as output if issues at the Router# prompt?
cl? with the caret (^) symbol below the question mark (?)
All commands available in privileged EXEC mode beginning with cl
All commands available in user EXEC mode beginning with cl
A list of all commands available in user EXEC mode
A list of all commands available in privileged EXEC mode
2
11. Select the true statements (Choose 3)
A password is mandatory to enter privileged EXEC mode
Passwords are set in the user EXEC mode
All monitoring must be performed in the user EXEC mode
enable secret takes precedence over enable password
show flash will display the file name of the active IOS
show version will display the file name of the active IOS
The router enters setup mode after deleting the running configuration
A DB9 – RJ45 and a crossover cable is used for a console connection
3
12. What will be the effect of performing the keystroke Esc-F?
Move to beginning of the command line
Move to the end of the command line
Move forward one word
Move back one word
2
13. What will be the effect of typing clo followed by Tab at the privileged EXEC
command prompt?
There will be an error message generated
The command prompt is displayed again
The command clock is displayed at the prompt
The caret (^) symbol will appear below the letter o in clo
2
14. What is the default number of command lines stored in the history buffer?
8
10
16
32
50
64
128
256
dgooch
2
3
CCNA2 EOC2 Revision Guide
15. What is the maximum number of command lines that can be stored in the
history buffer?
8
10
16
32
50
64
128
256
2
16. What is true concerning the pressing of the Ctrl-N key sequence at the
command prompt? (Choose 2)
Recalls the most recent command in the history buffer
The previous 10 commands are displayed
Disables the advanced editing features
Has the same effect as pressing the up arrow key
Has the same effect as pressing the down arrow key
Has the same effect as pressing the right arrow key
Has the same effect as pressing the left arrow key
2
17. What information is NOT displayed when using the show version command?
Configuration register setting
Bootstrap ROM version
Boot ROM version
Interface IP settings
IOS version and descriptive information
Last restart method
System image file and location
Router up time
Router platform
2
18. What can we determine if the dollar ($) symbol is seen on the command line?
There is an error in the entry
Not all of the command is visible
Has the same purpose as the question (?) symbol
Indicates the history buffer is full
/39
dgooch
4
2
%
CCNA2 EOC2 Revision Guide