Copyright 2004 and 2005 AIA
MASTERSPEC Short Form
09/04 (R 06/05)
SECTION 235100 - BREECHINGS, CHIMNEYS, AND STACKS
PART 1 - GENERAL
1.1
SUMMARY
A.
This Section includes the following:
1.
2.
3.
B.
1.2
Listed chimney liners.
Listed [single] [double]-wall [vents] [chimneys].
Listed [grease] [dishwasher] [grease and dishwasher] ducts.
See Division 23 Section "Draft Control Devices" for induced-draft and mechanical fans and for
motorized and barometric dampers.
SUBMITTALS
A.
Product Data: For the following:
1.
2.
3.
4.
5.
6.
B.
Chimney liners.
Type B and BW vents.
Type L vents.
Special gas vents.
Building-heating-appliance chimneys.
Grease ducts.
Shop Drawings: For vents, breechings, chimneys, and stacks.
sections, details, and attachments to other work.
Include plans, elevations,
PART 2 - PRODUCTS
2.1
LISTED CHIMNEY LINERS
A.
Available Manufacturers: Subject to compliance with requirements, manufacturers offering
products that may be incorporated into the Work include, but are not limited to, the following:
B.
Manufacturers: Subject to compliance with requirements, provide products by one of the
following:
C.
Basis-of-Design Product: Subject to compliance with requirements, provide [the product
indicated on Drawings] <Insert manufacturer's name; product name or designation> or a
comparable product by one of the following:
1.
2.
3.
American Metal Products; MASCO Corporation.
Deflect-O Corp.
Heat-Fab, Inc.
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 1
Copyright 2004 and 2005 AIA
4.
5.
6.
7.
8.
9.
10.
MASTERSPEC Short Form
09/04 (R 06/05)
Industrial Chimney Company.
Metal-Fab, Inc.
Selkirk Inc.; Selkirk Metalbestos and Air Mate.
Shook Manufactured Products, Inc.
Simpson Dura-Vent Co., Inc.; Subsidiary of Simpson Manufacturing Co.
Tru-Flex Metal Hose Corp.
<Insert manufacturer's name.>
D.
Description: [Straight] [Corrugated], single-wall chimney liner tested according to UL 1777
and rated for 1000 deg F (538 deg C) continuously, or 2100 deg F (1150 deg C) for 10 minutes;
with negative or positive flue pressure complying with NFPA 211.
E.
Straight Liner Materials: ASTM A 666, [Type 304] [Type 316] stainless steel.
F.
Corrugated Liner Materials: [ASTM A 240/A 240M, Type 321] [ASTM A 240/A 240M,
Type 430] [ASTM A 959, Type 29-4C] stainless steel.
G.
Accessories:
1.
2.
3.
2.2
Fittings: Tees, elbows, increasers, draft-hood connectors, metal caps with bird barriers,
adjustable roof flashings, storm collars, support assemblies, thimbles, firestop spacers,
and fasteners; fabricated from similar or compatible materials and designs.
Sealant: Manufacturer's standard high-temperature sealant.
Insulating Fill: Manufacturer's standard high-temperature insulation fill material in
annular space surrounding chimney liner including high-temperature, ceramic-fiber
insulation required to seal chimney at top and bottom.
LISTED TYPE B AND BW VENTS
A.
Available Manufacturers: Subject to compliance with requirements, manufacturers offering
products that may be incorporated into the Work include, but are not limited to, the following:
B.
Manufacturers: Subject to compliance with requirements, provide products by one of the
following:
C.
Basis-of-Design Product: Subject to compliance with requirements, provide [the product
indicated on Drawings] <Insert manufacturer's name; product name or designation> or a
comparable product by one of the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
American Metal Products; MASCO Corporation.
Cleaver-Brooks; Div. of Aqua-Chem Inc.
FAMCO.
Hart & Cooley, Inc.
Heat-Fab, Inc.
Industrial Chimney Company.
LSP Products Group, Inc.
Metal-Fab, Inc.
Schebler Co. (The).
Selkirk Inc.; Selkirk Metalbestos and Air Mate.
Simpson Dura-Vent Co., Inc.; Subsidiary of Simpson Manufacturing Co.
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 2
Copyright 2004 and 2005 AIA
12.
13.
14.
MASTERSPEC Short Form
09/04 (R 06/05)
Tru-Flex Metal Hose Corp.
Van-Packer Company, Inc.
<Insert manufacturer's name.>
D.
Description: Double-wall metal vents tested according to UL 441 and rated for 480 deg F (248
deg C) continuously for Type B, or 550 deg F (288 deg C) continuously for Type BW; with
neutral or negative flue pressure complying with NFPA 211.
E.
Construction: Inner shell and outer jacket separated by at least a 1/4-inch (6-mm) airspace.
F.
Inner Shell:
[ASTM B 209 (ASTM B 209M), Type 1100 aluminum] [ASTM B 209
(ASTM B 209M), Type 3003 aluminum] [ASTM B 209 (ASTM B 209M), Type 3105
aluminum] [ASTM A 666, Type 430 stainless steel].
G.
Outer Jacket: [Galvanized] [Aluminized] steel.
H.
Accessories: Tees, elbows, increasers, draft-hood connectors, terminations, adjustable roof
flashings, storm collars, support assemblies, thimbles, firestop spacers, and fasteners; fabricated
from similar materials and designs as vent-pipe straight sections; all listed for same assembly.
1.
2.
3.
4.
5.
2.3
Termination:
Termination:
Termination:
Termination:
Termination:
Stack cap designed to exclude minimum 90 percent of rainfall.
Round chimney top designed to exclude minimum 98 percent of rainfall.
Exit cone with drain section incorporated into riser.
Antibackdraft.
<Insert termination.>
LISTED TYPE L VENTS
A.
Available Manufacturers: Subject to compliance with requirements, manufacturers offering
products that may be incorporated into the Work include, but are not limited to, the following:
B.
Manufacturers: Subject to compliance with requirements, provide products by one of the
following:
C.
Basis-of-Design Product: Subject to compliance with requirements, provide [the product
indicated on Drawings] <Insert manufacturer's name; product name or designation> or a
comparable product by one of the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
American Metal Products; MASCO Corporation.
FAMCO.
Heat-Fab, Inc.
Industrial Chimney Company.
LSP Products Group, Inc.
Metal-Fab, Inc.
Schebler Co. (The).
Selkirk Inc.; Selkirk Metalbestos and Air Mate.
Simpson Dura-Vent Co., Inc.; Subsidiary of Simpson Manufacturing Co.
Tru-Flex Metal Hose Corp.
Van-Packer Company, Inc.
<Insert manufacturer's name.>
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 3
Copyright 2004 and 2005 AIA
MASTERSPEC Short Form
09/04 (R 06/05)
D.
Description: Double-wall metal vents tested according to UL 641 and rated for 570 deg F (300
deg C) continuously, or 1700 deg F (926 deg C) for 10 minutes; with neutral or negative flue
pressure complying with NFPA 211.
E.
Construction: Inner shell and outer jacket separated by at least a [1/4-inch (6-mm)] [1-inch
(25-mm)] [2-inch (50-mm)] [4-inch (100-mm)] airspace filled with high-temperature,
[ceramic-fiber] [mineral-wool] insulation.
F.
Inner Shell: ASTM A 666, [Type 304] [Type 316] stainless steel.
G.
Outer Jacket: [Galvanized] [Aluminized] [Stainless] steel.
H.
Accessories: Tees, elbows, increasers, draft-hood connectors, terminations, adjustable roof
flashings, storm collars, support assemblies, thimbles, firestop spacers, and fasteners; fabricated
from similar materials and designs as vent-pipe straight sections; all listed for same assembly.
1.
2.
3.
4.
2.4
Termination:
Termination:
Termination:
Termination:
Stack cap designed to exclude 90 percent of rainfall.
Round chimney top designed to exclude 98 percent of rainfall.
Exit cone with drain section incorporated into riser.
<Insert termination.>
LISTED SPECIAL GAS VENTS
A.
Available Manufacturers: Subject to compliance with requirements, manufacturers offering
products that may be incorporated into the Work include, but are not limited to, the following:
B.
Manufacturers: Subject to compliance with requirements, provide products by one of the
following:
C.
Basis-of-Design Product: Subject to compliance with requirements, provide [the product
indicated on Drawings] <Insert manufacturer's name; product name or designation> or a
comparable product by one of the following:
1.
2.
3.
4.
5.
Heat-Fab, Inc.
Metal-Fab, Inc.
Selkirk Inc.; Selkirk Metalbestos and Air Mate.
Z-Flex; Flexmaster Canada Limited.
<Insert manufacturer's name.>
D.
Description: Double-wall metal vents tested according to UL 1738 and rated for 480 deg F (248
deg C) continuously, with positive or negative flue pressure complying with NFPA 211.
E.
Construction: Inner shell and outer jacket separated by at least a 1/2-inch (13-mm) airspace.
F.
Inner Shell: ASTM A 959, Type 29-4C stainless steel.
G.
Outer Jacket: [Aluminized] [Stainless] steel.
H.
Accessories: Tees, elbows, increasers, draft-hood connectors, terminations, adjustable roof
flashings, storm collars, support assemblies, thimbles, firestop spacers, and fasteners; fabricated
from similar materials and designs as vent-pipe straight sections; all listed for same assembly.
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 4
Copyright 2004 and 2005 AIA
1.
2.
3.
4.
2.5
Termination:
Termination:
Termination:
Termination:
MASTERSPEC Short Form
09/04 (R 06/05)
Stack cap designed to exclude minimum 90 percent of rainfall.
Round chimney top designed to exclude minimum 98 percent of rainfall.
Exit cone with drain section incorporated into riser.
<Insert termination.>
LISTED BUILDING-HEATING-APPLIANCE CHIMNEYS
A.
Available Manufacturers: Subject to compliance with requirements, manufacturers offering
products that may be incorporated into the Work include, but are not limited to, the following:
B.
Manufacturers: Subject to compliance with requirements, provide products by one of the
following:
C.
Basis-of-Design Product: Subject to compliance with requirements, provide [the product
indicated on Drawings] <Insert manufacturer's name; product name or designation> or a
comparable product by one of the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
American Metal Products; MASCO Corporation.
Cleaver-Brooks; Div. of Aqua-Chem Inc.
FAMCO.
Hart & Cooley, Inc.
Heat-Fab, Inc.
Industrial Chimney Company.
LSP Products Group, Inc.
Metal-Fab, Inc.
Schebler Co. (The).
Selkirk Inc.; Selkirk Metalbestos and Air Mate.
Simpson Dura-Vent Co., Inc.; Subsidiary of Simpson Manufacturing Co.
Tru-Flex Metal Hose Corp.
Van-Packer Company, Inc.
<Insert manufacturer's name.>
D.
Description: Double-wall metal vents tested according to UL 103 and rated for 1000 deg F (538
deg C) continuously, or 1700 deg F (926 deg C) for 10 minutes; with neutral or negative flue
pressure complying with NFPA 211.
E.
Construction: Inner shell and outer jacket separated by at least a [1/2-inch (25-mm)] [1-inch
(50-mm)] [2-inch (50-mm)] [3-inch (75-mm)] [4-inch (100-mm)] annular space[ filled with
high-temperature, ceramic-fiber insulation].
F.
Inner Shell: ASTM A 666, [Type 304] [Type 316] stainless steel.
G.
Description: Double-wall metal vents tested according to UL 103 and UL 959 and rated for
1400 deg F (760 deg C) continuously, or 1800 deg F (982 deg C) for 10 minutes; with positive
or negative flue pressure complying with NFPA 211.
H.
Construction: Inner shell and outer jacket separated by at least a [1-inch (25-mm)] [2-inch (50mm)] [3-inch (75-mm)] [4-inch (100-mm)] annular space filled with high-temperature,
ceramic-fiber insulation.
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 5
Copyright 2004 and 2005 AIA
MASTERSPEC Short Form
09/04 (R 06/05)
I.
Inner Shell: ASTM A 666, [Type 304] [Type 316] stainless steel.
J.
Description: Double-wall metal vents tested according to UL 103 and rated for 1000 deg F (538
deg C) continuously, or 2100 deg F (1150 deg C) for 10 minutes; with neutral or negative flue
pressure complying with NFPA 211.
K.
Construction: Inner shell and outer jacket separated by at least a [1-inch (25-mm)] [1-1/2-inch
(38-mm)] [2-inch (50-mm)] [4-inch (100-mm)] annular space filled with high-temperature,
ceramic-fiber insulation.
L.
Inner Shell: [ASTM A 666, Type 304] [ASTM A 666, Type 316] [ASTM A 240/A 240M,
Type 430] stainless steel.
M.
Outer Jacket: [Galvanized] [Aluminized] [Stainless] steel.
N.
Accessories: Tees, elbows, increasers, draft-hood connectors, terminations, adjustable roof
flashings, storm collars, support assemblies, thimbles, firestop spacers, and fasteners; fabricated
from similar materials and designs as vent-pipe straight sections; all listed for same assembly.
1.
2.
3.
4.
2.6
Termination:
Termination:
Termination:
Termination:
Stack cap designed to exclude minimum 90 percent of rainfall.
Round chimney top designed to exclude minimum 98 percent of rainfall.
Exit cone with drain section incorporated into riser.
<Insert termination.>
LISTED GREASE DUCTS
A.
Available Manufacturers: Subject to compliance with requirements, manufacturers offering
products that may be incorporated into the Work include, but are not limited to, the following:
B.
Manufacturers: Subject to compliance with requirements, provide products by one of the
following:
C.
Basis-of-Design Product: Subject to compliance with requirements, provide [the product
indicated on Drawings] <Insert manufacturer's name; product name or designation> or a
comparable product by one of the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
American Metal Products; MASCO Corporation.
FAMCO.
Heat-Fab, Inc.
Industrial Chimney Company.
LSP Products Group, Inc.
Metal-Fab, Inc.
Schebler Co. (The).
Selkirk Inc.; Selkirk Metalbestos and Air Mate.
Simpson Dura-Vent Co., Inc.; Subsidiary of Simpson Manufacturing Co.
Tru-Flex Metal Hose Corp.
Van-Packer Company, Inc.
<Insert manufacturer's name.>
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 6
Copyright 2004 and 2005 AIA
MASTERSPEC Short Form
09/04 (R 06/05)
D.
Description: Double-wall metal vents tested according to UL 1978 and rated for 500 deg F (260
deg C) continuously, or 2000 deg F (1093 deg C) for 30 minutes; with positive or negative duct
pressure and complying with NFPA 211.
E.
Construction: Inner shell and outer jacket separated by at least a [1-inch (25-mm)] [2-inch (50mm)] [3-inch (75-mm)] [4-inch (100-mm)] annular space filled with high-temperature,
ceramic-fiber insulation.
F.
Inner Shell: ASTM A 666, [Type 304] [Type 316] stainless steel.
G.
Outer Jacket: [Aluminized] [Stainless] steel where concealed. Stainless steel where exposed.
H.
Accessories: Tees, elbows, increasers, hood connectors, terminations, adjustable roof flashings,
storm collars, support assemblies, thimbles, firestop spacers, and fasteners; fabricated from
similar materials and designs as vent-pipe straight sections; all listed for same assembly.
Include unique components required to comply with NFPA 96 including cleanouts, transitions,
adapters and drain fittings.
PART 3 - EXECUTION
3.1
APPLICATION
A.
Listed Chimney Liners: High-efficiency boiler or furnace vents in masonry chimney,
dishwasher exhaust, or Type II commercial kitchen hood.
B.
Listed Type B and BW Vents: Vents for certified gas appliances.
C.
Listed Type L Vents: Vents for low-heat appliances.
D.
Listed Special Gas Vents: Condensing gas appliances.
E.
Listed Building-Heating-Appliance Chimneys: Dual-fuel boilers, oven vents, water heaters,
and exhaust for engines. Fireplaces and other solid-fuel-burning appliances.
F.
Listed Grease Ducts: Type I commercial kitchen grease duct.
3.2
INSTALLATION OF LISTED VENTS AND CHIMNEYS
A.
Locate to comply with minimum clearances from combustibles and minimum termination
heights according to product listing or NFPA 211, whichever is most stringent.
B.
Seal between sections of positive-pressure vents and grease exhaust ducts according to
manufacturer's written installation instructions, using sealants recommended by manufacturer.
C.
Support vents at intervals recommended by manufacturer to support weight of vents and all
accessories, without exceeding appliance loading.
D.
Slope breechings down in direction of appliance, with condensate drain connection at lowest
point piped to nearest drain.
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 7
Copyright 2004 and 2005 AIA
MASTERSPEC Short Form
09/04 (R 06/05)
E.
Lap joints in direction of flow.
F.
After completing system installation, including outlet fittings and devices, inspect exposed
finish. Remove burrs, dirt, and construction debris and repair damaged finishes.
G.
Clean breechings internally, during and after installation, to remove dust and debris. Clean
external surfaces to remove welding slag and mill film. Grind welds smooth and apply touchup
finish to match factory or shop finish.
H.
Provide temporary closures at ends of breechings, chimneys, and stacks that are not completed
or connected to equipment.
END OF SECTION 235100
BREECHINGS, CHIMNEYS, AND STACKS
235100 - 8