S-1-1
Instructions to Authors for JSED2015
Taro Mizumoto1 * and Jiro Muroran2
1
Department of Materials Science and Engineering, Muroran Institute of Technology,
Mizumoto 27-1, Muroran 050-8585, Japan
2
Applied Physics and Chemistry, The University of Electro-Communications,
Chofugaoka 1-5-1, Chofu, Tokyo 182-8585, Japan
Email: mizumoto@mmm.muroran-it.ac.jp
1. Introduction.
These are the guidelines for preparation of papers for JSED2015 [1]. Please use this document as a
template and adhere strictly to the following guidelines and formatting requirements [1,2].
2. Paper layout
The paper size (page size) should be A4 (width 210 mm and height 297 mm). The total length
should be two pages or four pages. Page numbers should not be included. The main body should be
typed in a single-spaced column with margins as in Table 1.
Table 1. Page dimensions
Parameters
Values
Top margin
30 mm
Bottom margin
25 mm
Left and right margins
25 mm
Column width
160 mm
3. Fonts, alignment, indentation, and spacing
The typeface (font) should be Times New Roman for all components except mathematical
formulae. The font size should be 11 pt unless otherwise stated.
The title should be boldfaced in 16 pt, and centered. The first letter of each word should be in
uppercase, except for articles and prepositions. A blank line should be inserted before the title for the
program number, one should also be inserted after the title.
The authors’ names should be in 14 pt and centered. Place an asterisk after the corresponding
author’s name. Place superscripted Arabic numerals after authors’ names to indicate their affiliations;
no Arabic numerals are necessary if there is only one affiliation. A blank line should be inserted after
the authors’ names.
The authors’ affiliations and address should be in 10 pt and centered. Place a superscripted,
upright Arabic numeral before each affiliation to indicate the correspondences between authors and
affiliations.
The corresponding author’s e-mail address should be placed in the line beneath the affiliations.
Two blank lines should be inserted after the e-mail address.
The main body of the text should be justified to both the left and right margins of the column. The
first line of each paragraph should be indented by 6 mm.
4. Headings
Headings should be boldfaced in 11 pt. The first letter of the first word only should be in
uppercase. A blank line should be inserted before each of the first-level headings, but none after the
first-level headings.
5. Figures, tables, and equations
All figures and tables should be referred to in the following way: “Figure 1,” “Figures 1 and 2,” or
“Tables 1–3.” Place figure captions below the figures and table captions above the table. Captions
should be centered.
Equations should be centered and numbered consecutively with Arabic numerals enclosed in
parentheses, as follows.
(1)
(2)
Be sure that symbols in equations are clearly defined.
Figure 1. A typical seismic event
References
---The list of references should be placed at the end of the paper, in order of citation in the main
text. References should be referred to in the text by Arabic numerals enclosed in square brackets, as
[1], [1, 2], [1–3], and so on.
[1] Block, L. V., Cheng, C. H., Fehler, M. C. and Phillipe, W. S., 1994, Seicmic imaging using
microearthquakes induced by hydraulic fracturing: Geophysics, 59, 102–112.
[2] Childers, D. G., Skinner, D. P. and Kemerait, R. C., 1977, The cepstrum -A guide to processing:
Proceedings of IEEE, 65, 1428–1443.
Instructions for making paper
Please refer to this paper sample ( or rewrite the paper sample)
Documents must be written on A4 by Microsoft Word and Adobe Acrobat.
Documents must be 2 pages or 4 pages including figures and tables.
Please send the documents to
Secretary Office E-mail: jsed2015@mmm.muroran-it.ac.jp
Not later than December 27, 2014
The names of the two files (MS Word and Adobe Acrobat) should include author’s name (e.g.
“mizumoto.doc” and “mizumoto.pdf” <author’s name +.doc or .pdf>)