EdgeGuard “Extreme” Pattern
Installation Instructions
EdgeGuard “Extreme” patterns are easy to install. However, to assure proper installation, it is IMPORTANT that
you read these directions thoroughly and then follow them carefully.
An experienced individual can install EdgeGuard on a windshield in 20 – 25 minutes. First time installers may take as
much as 1 hour. Do not install EdgeGuard on a cracked or severely pitted windshield.
The greatest challenge in installing EdgeGuard is in preventing minute particles of dirt from being trapped between the
EdgeGuard material and the windshield. If this happens, tiny pockets or gaps will form under the material. Although this
won’t affect the performance of the product, it will affect how it looks on the vehicle. Washing the car prior to installation,
especially around the windshield molding, is advised. EdgeGuard MUST be installed in a relatively clean, indoor
environment such as a garage.
The other important consideration in installing EdgeGuard is in removing all of the special EdgeGuard Application Solution
from between the windshield and the EdgeGuard material after it’s applied. If this is not done, the adhesive will not be
crystal clear in all areas of the application. Temperature is also a factor. For best results, EdgeGuard should be installed
at air and windshield temperatures between 50° and 95°F.
Below are detailed instructions – we strongly advise you read these at least once. To guide you through the actual
installation process, we’ve also provided a quick reference checklist.
After installation…
ü Do not wash your car (and preferably, don’t expose it to rain) for 48 hours.
ü Use care when removing ice and snow from your windshield. An ice scraper can scratch and even gouge the
EdgeGuard material.
ü Avoid using plastic solvents on your windshield as they may dissolve the EdgeGuard material.
Component Verification and Work Area Preparation
Check that you have all the following components available:
ü 4-piece EdgeGuard pattern*
ü Non-scratching white nylon scrub pad
ü Single edge stainless steel razor blade
ü Lint-Free cloths
ü EdgeGuard application solution
ü EdgeGuard installation squeegee
ü Glass cleaning solution
ü Paper towels
ü Masking or “Scotch” tape
*Note: Each piece of the EdgeGuard pattern is actually composed of 3 layers.
a. Top side (with part identification label attached) release film that will be removed and discarded.
b. High-impact, LEXAN® material with adhesive backing
c. Adhesive side release film that will be removed and discarded.
Park your vehicle in a clean, well lit, indoor environment where temperatures are between 50° and 95 °F.
Thoroughly wash your hands.
Arrange the installation kit components provided so that they are within easy reach as you carry out the installation.
Note: Depending on your height and the height of your vehicle, you might find a step stool or small ladder helpful in
installing EdgeGuard. It is much easier to use the squeegee while pressing downward vs. reaching while standing
on your toes.
EdgeGuard_Installation_Instructions_030314
EdgeGuard Installation Instructions
Page 2 of 4
Pattern Verification
Each “Extreme” EdgeGuard pattern has been designed and quality checked to fit the windshield of a specific vehicle
manufacturer’s make, model, and year. However, because of variations in the installation process of the molding that
surrounds the windshield at the factory, and in some cases, manufacturers making unannounced changes to the
dimensions of the molding that surrounds the windshield during a model year, there will be instances where the installer
will need to trim areas of the individual pieces that make up the EdgeGuard pattern.
Prior to removing the release films from either side of the EdgeGuard material, using several small pieces of tape, “test fit”
the 4 pieces of the EdgeGuard material by positioning each on your windshield and confirm they fit per the drawing
below. Trim the pieces as necessary and then set aside.
Windshield Surface Preparation
For best results, use a glass cleaning solution and paper towel to clean the painted area surrounding the windshield.
Using the windshield cleaning solution and non-scratching white nylon scrub pad provided, aggressively clean the
windshield and surrounding molding.
Before wiping the glass cleaning solution from the windshield, use the single edge razor blade provided to
thoroughly scrape off any foreign material from the outer 6 inches of the windshield surface. This is a critical
step!
Wipe the windshield clean with one of the blue lint free towels provided.
Apply a liberal amount of the special EdgeGuard Application Solution to the perimeter of the windshield, and starting at
the top, use the squeegee provided to remove as much of the Application Solution as possible. The windshield should
now be as clean as it’s ever been. Do NOT take a break. The longer you wait, the more dust will accumulate on your
windshield – increasing the chances of tiny unsightly pockets forming under the EdgeGuard material.
2
EdgeGuard Installation Instructions
Page 3 of 4
EdgeGuard Material Installation
1. Attach a small piece of tape to the corner of the top side (side with
identification label attached) of the EdgeGuard material labeled
“Passenger’s side” and using the tape as a handle, remove the
release film (See Fig. 1).
2. Attach another small piece of tape to the corner of the adhesive
side of the same piece of EdgeGuard material and peel back a
small amount (approx. ½’’) of the release film.
3. Before removing the protective backing from the adhesive side,
spray both sides of the material with the Application Solution to
avoid static electricity. Grip the EdgeGuard material by the edges
(See Fig. 2) to avoid touching the adhesive surface. Now carefully
peel off the protective backing from the adhesive side of the
material by using the piece of tape (See Fig. 1) and liberally spray
the adhesive side with the Application Solution (See Fig. 2)
NEVER allow the adhesive side of the EdgeGuard material to
come in contact with anything but the application solution and
your windshield. Always hold the material by the edges only.
4. Using the Application Solution, lightly spray the area where the
EdgeGuard material is to be placed, carefully lay the pattern onto
the windshield (adhesive side down) and slide the pattern into
position (See Fig. 3). Pattern should be positioned approximately
1/8’’ from the windshield’s molding and should never overlap any
other EdgeGuard pieces. (See Fig. 4)
5. While holding the EdgeGuard material in place with one hand,
gently squeegee the Application Solution out from beneath the
material by working from the center of the piece and squeegeeing
outward (See Fig. 5). Repeat this process with increased squeegee
pressure until moisture and air bubbles are no longer visible. You
may need to lightly spray the EdgeGuard material with the
Application Solution to keep the squeegee from grabbing or
skipping. Again, the goal is to remove all the remaining moisture
from between the EdgeGuard material and your windshield,
providing for a securely installed piece.
6. Blot up any residual liquid from around the EdgeGuard material
using a lint free towel.
7. Repeat steps 1 - 6 for the remaining 3 pieces of EdgeGuard
material, starting with piece labeled “Driver’s Side”.
8. After all the pieces are in place, look for any bubbles and press
them out with the squeegee.
9. Allow to dry for a minimum of 2 hours out of direct sunlight.
Congratulations! Your installation is now complete!
3
EdgeGuard Installation Instructions
Page 4 of 4
EdgeGuard Consumer Installation Quick Reference Checklist
IMPORTANT:
This checklist is provided as an aid in the proper installation of EdgeGuard. It is NOT a substitute for reading the detailed
instructions provided. It is critical that you read the detailed instructions provided AT LEAST ONCE before referring to
this checklist while you carry out the actual installation.
If you have any questions, please contact us at (toll free) 877-388-2300 or sales@edgeguard.com.
2
Description
Component Verification and Work Area Preparation
All components on hand (see checklist on page 1)
Vehicle in well lit, enclosed environment
Hands washed
Components arranged
Pattern Verification
EdgeGuard material is proper size for windshield – see drawing below
Surface Preparation
Clean windshield, molding, and surrounding painted area – use razor over outer 6 inches
Wipe dry with lint free towel
Clean windshield again, without razor and dry with lint free towel
Spray with Application Solution and squeegee off starting at the top
EdgeGuard Material Installation
Remove top side release film
Begin to peel back adhesive side release film – liberally spray both sides of EdgeGuard
material using the EdgeGuard Application Solution
Make note of adhesive side – remove release film – spray adhesive side
Spray area of windshield where material is to be placed with Application Solution
Place EdgeGuard material on windshield
Squeegee application solution from beneath material
Blot up any remaining application solution
Repeat for remaining pieces
Blot up all remaining application solution
Squeegee out any remaining bubbles
Allow to dry for a minimum of 2 hours out of direct sunlight
4