BOWSER-MORNER, INC. - GEOTECHNICAL LABORATORY
AASHTO/ISO 17025 ACCREDITED • AASHTO R 18 ACCREDITED • USACE VALIDATED
2013 Laboratory Testing Fees - Soil and Rock
Add 20% for samples recovered from C or D level hazard sites. Samples recovered from A or B sites will be considered on a case by case basis.
Sampling & Consultation
Sampling - Time
Sampling - Mileage
Consultation, Senior Geologist/Engineer
$60.00/Hour
$0.65/Mile
$130.00/Hour
Texture Plasticity, and Density Properties
1. Moisture Content (D 2216, T 265)
$9.70
2. Atterberg Limits
a. Plasticity Index (D 4318, T 89, T 90)
$92.00
b. Liquid Limit or Plastic Limit Only
$77.00
c. Shrinkage Limit (D 427, T 92)
$410.00
3. Specific Gravity (D 854, T 100)
$72.00
4. Particle-Size Analysis (jar sample, D 422, D 1140, T 88, T 311)
a. Sieve & Hydrometer (cohesive soils)
$144.00
b. Sieve Only - thru No. 200 (granular soils)
$87.00
c. Sieve Only - thru No. 635 Sieve
$128.00
d. Bank run samples (bag sample, long-graded)
$174.00
5. Compaction Characteristics
a. Standard Proctor - 5 Points (D 698, T 99)
$185.00
b. Modified Proctor - 5 Points (D 1557, T 180)
$185.00
c. One Point Verification (D 698, D 1557, T 99)
$82.00
d. Relative Density (D 4253 & D 4254)
$390.00
6. Unit Weight (includes Moisture Content & Extrusion)
a. Direct Measurement (D 7263 - Method B)
$67.00
b. Paraffin Method (D 7263 - Method A, T 233)
$82.00
Identification and Classification
7. USCS Classification (D 2487)
a. Cohesive Soils (incl. D 422, D 2216, D 4318)
$199.00
b. Granular Soils (incl. D 422, D 2216)
$92.00
8. Visual Description
a. Quick-jar
$32.00
b. Shelby Tube-log, moisture, extrusion
$52.00
Structural Properties
9. Unconfined Compression - incl. Extrusion, Unit Wt.,
Load Curve (D 2166, T 209)
$92.00
10. One-Dimensional Consolidation (D 2435, T 216) incl. Specific Gravity (D 854, T 100)
a. E log p curve, incl. Time-settlement curves
$580.00
b. Rebound and Reload - additional
$194.00
11. One-Dimensional Swell or Settlement Potential (D 4546)
a. Swell Pressure
$870.00
b. Percent Swell
$870.00
12. 3D Consolidation (Triaxial Method)
$1,230.00
13. California Bearing Ratio, CBR (D 1883, T 193), one point
$240.00
each additional point
$134.00
14. Direct Shear Testing, per 3 pts, incl. Extrusion, unit wt, & moisture
a. Direct Shear, Drained (D 3080, T 236)
$660.00
15. Triaxial Testing, per 3 points, incl. Extrusion, Unit Wt., and Moisture
a. Unconsolidated-Undrained (Q, UU), (D 2850, T 252)
$460.00
b. Consolidated-Undrained (R, CU, CUPP), (D 4767, T 297) includes:
back pressure saturation and pore pressure
$980.00
c. Remolding specimens, per set of 3
$310.00
Soil-Cement/Cement Treated Base/Lime-Stabilized Mixes
16. Mix Design (5 Percentages), incls 15 strength specimens, T 134
$1,860.00
17. Wet-Dry Durability (D 559, T 135) - 5 cement percentages
$1,440.00
18. Freeze-Thaw Durability (D 560, T 136) - 5 cement percentages
$1,440.00
19. Compressive Strength (D 558, T 220), per specimen
$62.00
Shipping Address:
4518 Taylorsville Road, Dayton, OH 45424
226 West Highland Ave., Springfield, IL 62704
3016 Commerce Sq. S., Birmingham, AL 35210
Contact Person:
Karl A. Fletcher, Manager
Bill Sheftick, Manager
Clark H. Lamb, Manager
Hydraulic Properties
20. Laboratory Hydraulic Conductivity (Permeability)
a. Flexible-Wall, Cohesive Soils (D 5084)
i. Undisturbed
ii. Remolded
iii. With confining pressure, additional
b. Rigid-Wall, granular soils , incl. Remolding
i. Constant Head (D 2434, T 215)
ii. Compaction Mold Method, Falling or Constant Head (D 5856)
21. Gradient Ratio (D 5101)
Physico-Chemical Properties
22. pH (D 4972, T 289)
23. a. CEC; EPA Method 9080A (Ammonium Acetate)
b. CEC; EPA Method 9081A (Sodium Acetate)
24. a. Percent Organic - Loss on Ignition (D 2974, T 267)
b. Wet Combustion; Potassium Dichromate (T 194)
25. Total Organic Carbon (EPA Method 9060A)
a. EPA Method 9060A
b. Walkley-Black Method
26. Resistivity, Lab (G 187, T 288)
27. Water Soluble Sulfate Ion (AASHTO T 290)
28. Water Soluble Chloride Ion (AASHTO T 291)
29. Sample Prep for items 23 & 24
30. Agricultural Analysis
31. X-Ray Diffraction/Mineralogy
32 Water-Soluble Sulfate Ion - Texas Method (ODOT) - incl's prep
MSE Wall Parameters
33. a. Sieve Analysis (ASTM C 136, D 422, D 1140, T 27, T 88)
b. Long-Graded Sieve (ASTM C 136, D 422, D 1140, T 27, T 88)
34. Compaction Characteristics, Std. Proctor (D 698 or T 99):
35. Direct Shear Testing, per 3 pts, incl. remolding (D 3080 or T 236)
36. Hydraulic Conductivity (Permeability), (D 2434 or T 215)
37. Resistivity, Lab (ASTM G 187 or AASHTO T 288)
38. pH (D 4972 or T 289)
39. Water Soluble Sulfate Ion (ASTM D 516, AASHTO T 290)
40. Water Soluble Chloride Ion (ASTM D 512, AASHTO T 291)
41. Sample Prep for items 34 & 35
42. Loss on Ignition (LOI) (ASTM D 2974, AASHTO T 267)
43. Plasticity Index (ASTM D 4318, AASHTO T 89, T 90)
44. 4-Cycle Magnesium Sulfate Soundness (req'd by FHWA)
Rock Mechanics
45. Compressive Strength (D 2938/ D 7012 Procedure C)
46. Splitting Tensile Strength (D 3967)
47. Indirect Diametrical Strength (Brazilian)
48. Density, Porosity, Void Ratio (D 7263)
49. Cut/Prep Core Specimen (D 4543)
50. Point Load Test (D 5731)
51. Cerchar Abrasivity Index
Rock Weathering (Riprap/Armor Stone)
52. Slake Durability ( D 4644)
53. Jar Slake Durability (KM 64-514)
54. Freeze Thaw (D 5312, CRD-C 144)
55. Wet Dry (D 5313, CRD-C 169)
56. Soundness-Slab Method (D 5240)
57. Petrographic Examination (C 295/ D 4992)
58. Specific Gravity/Absorption (D 6473)
59. Adsorption/Absorption Ratio
60. Sample Prep for items 54, 55, 56 (cut/ trim slabs) (D 5121)
$300.00
$330.00
$1,260.00
$46.00
$180.00
$180.00
$64.00
$166.00
$82.00
$82.00
$230.00
$72.00
$72.00
$62.00
$180.00
$220.00
$100.00
$87.00
$170.00
$185.00
$660.00
$300.00
$230.00
$46.00
$72.00
$72.00
$62.00
$64.00
$92.00
$350.00
$90.00
$130.00
$130.00
$70.00
$60.00
$40.00
$200.00
$100.00
$60.00
$900.00
$900.00
$900.00
$1,600.00
$130.00
$130.00
$350.00
Contact Information:
937-236-8805 ext 322, cell: 937-750-2400, fax: 937-233-2016, kfletcher@bowser-morner.com
217-544-8378, cell: 217-544-8378, fax: 217-744-7625, wsheftick@bowser-morner.com
205-956-8805, cell: 205-999-7792, fax: 205-956-8865, clamb@bowser-morner.com
Technical Director for all locations: James W. Fletcher, VP: cell: 937-974-2507 jfletcher@bowser-morner.com
6/4/2013
$330.00
$400.00
$52.00
BOWSER-MORNER, INC. - CONSTRUCTION MATERIALS LABORATORY
AASHTO/ISO 17025 ACCREDITED ● AASHTO R 18 ACCREDITED ● USACE VALIDATED
2013 MINERAL AGGREGATES TESTING FEES
Sampling & Consultation
Sampling - Time ASTM D75, AASHTO T 2)
Sampling - Mileage (ASTM D75, AASHTO T 2)
Consultation, Senior Geologist/Engineer
Common DOT & USACE Additional Quality Parameters
$60.00/Hour
$0.65/Mile
$130.00/Hour
27. ODOT Unsound Chert (ASTM C88, AASHTO T 104/ ODOT Supplement 1029)
$340.00
28. 50 Cycle Water Freeze-Thaw (AASHTO T 103)
$450.00
29. 25 Cycle Brine Freeze-Thaw (INDOT 209-94)
$450.00
30. Visual Deleterious (DOT Procedures/ASTM C294, 295 Guidelines)
Sample Preparation & Geologist Logging
1. Necessary Sample Preparation
a. soft pcs, chert, shale, F&E, etc.
a. Ledge Rock, etc., crush to test specimens
b. Rock Core, split & archive representative half
$60.00/Hour
$3.80/ft.
c. Rock Core, crush to test specimens
$3.80/ft.
d. Geologist Log
$3.80/ft.
e. Rock Core, log, split, crush (items 1b, 1c, & 1d)
$8.00/ft.
$240.00
b. IDOT Delet., incl's soft/unsound/lt. wt. chert
c. USACE Table 5 Deleterious Airfield Parameters
d. USACE Scratch Hardness CRD C-130
$120.00
31. Crush Count; Percent Crushed/ Fractured (D5821, T 335)
ASTM C 33 Table 1 Quality Parameters for Fine Aggregate
a. One-Face
$80.00
b. Two-Face
$100.00
2. Sieve Analysis; Gradation (ASTM C136, AASHTO T 27)
$72.00
32. Micro-Deval Abrasion (ASTM D6928, D7428, AASHTO T 327)
3. Material Passing No. 200 Sieve/Decantation (ASTM C117, AASHTO T 11)
$62.00
33. Flat & Elongated Particles (D4791)
4. Five Cycle Soundness (ASTM C88, AASHTO T 104)
$180.00
$340.00
b. Magnesium Sulfate (5 Size Fractions Max.)
$350.00
35. Unit Weight (ASTM C29, AASHTO T 19)
c. IDOT/ PennDOT Method (AASHTO T 104, Mod.)
$350.00
36. Specific Gravity and Absorption (ASTM C127, C128, AASHTO T 85, T 84)
5. Lightweight Particles @ 2.00 Gs (ASTM C123, AASHTO T 113); coal & lignite
7. Organic Impurities, a. Colormetric (ASTM C40, AASHTO T 21)
b. Effect of Organics, performed if C 40 > 3, ASTM C87, AASHTO T 71
8. Complete Quality Analysis (C 33) - Includes items 2 - 7 (except 7.b.), 35, 36:
$260.00
$80.00
34. Pore Index (KM 64-623)
a. Sodium Sulfate (5 Size Fractions Max.)
6. Clay Lumps & Friable Particles (ASTM C142, AASHTO T 112)
$350.00
$2,200.00
Aggregate Index Parameters
$66.00
$240.00
a. Short-graded
$90.00
$80.00
b. Long-graded
$144.00
$62.00
$2,000.00
37. Aggregate Durability Index (ASTM D3744, AASHTO T 210)
$800.00
(unit weight, specific gravity & absorption)
a. Fine Aggregate (ASTM C1252, AASHTO T 304)
$170.00
b. Coarse Aggregate (AASHTO T 326)
$170.00
39. Sand Equivalency (ASTM D2419, AASHTO T 176)
ASTM C 33 Table 3 Quality Parameters for Coarse Aggregate
$230.00
38.Uncompacted Voids Test (Angularity Index), incl. Spec. grav.
9. Sieve Analysis; Gradation (ASTM C136, AASHTO T 27)
$72.00
40. Insoluble Residue; Acid Solubility (ASTM D3042)
10. Material Passing No. 200 Sieve/Decantation (ASTM C117, AASHTO T 11)
$62.00
41. Moh's Hardness AWWA B100, Sec. 5.3.5.
11. Five Cycle Soundness (ASTM C88, AASHTO T 104)
a. Plus No. 4 Material
$98.00
$134.00
$70.00
a. Sodium Sulfate (5 Size Fractions Max.)
$340.00
b. Magnesium Sulfate (5 Size Fractions Max.)
$350.00
42 Methylene Blue Test (ODOT Supplement 1052/ AASHTO T 330)
$220.00
c. IDOT/ PennDOT Method (AASHTO T 104, Mod.)
$350.00
43. Stain Test (ASTM C641)
$260.00
12. Los Angeles Abrasion (ASTM C131, C535, AASHTO T 96)
$150.00
13. Lightweight Particles @ Gs 2.4 (ASTM C123, AASHTO T 113); lt wt chert
$240.00
14. Clay Lumps & Friable Particles (ASTM C142, AASHTO T 112)
$80.00
15. Complete Quality Analysis (C 33) - Includes items 9 - 14, 30a,
$1,200.00
b. Minus No. 4 Material, includeS prep
$160.00
Rock Mechanics
44. Compressive Strength (ASTM D2938, D7012 Procedure C)
$90.00
45. Splitting Tensile Strength (ASTM D3967)
$130.00
46. Indirect Diametrical Strength (Brazilian)
$130.00
31, 33, 35, 36 :unit weight, specific gravity, absorption,
47. Cut/Prep Core Specimen (ASTM D4543)
$60.00
% crushed, flat & elongated, deleterious
48. Density, porosity, void ratio (ASTM D7263)
$70.00
49. Point Load Test (ASTM D5731)
ASTM C 33 Optional Parameters
16. Aggregate Durability Factor Rapid Freeze-Thaw (C666, C215, AASHTO T 161, CRD-C C114)
$200.00
a. Procedure A, USACE, 300 cycles, Durability Factor (DF)
$2,500.00
b. Procedure B, DOT, 350 cycles, Expansion & Durability Factor (DF)
$2,500.00
51. Slake Durability ( ASTM D4644)
$600.00
52. Jar Slake Durability (KM 64-514)
c. each additional beam over 3 per set above
d. each additional cycle over 350 per set above
$6.00
$40.00
50. Cerchar Abrasivity Index
Rock Weathering (Riprap/Armor Stone)
$100.00
$60.00
53. Freeze Thaw - 5 slabs (ASTM D5312, CRD-C 144 ) - up to 40 cycles,
17. Alkali Silica Reactivity (ASR)
$900.00
additional cycles $10.00 ea.
a. 6 Month Mortar Bar Method (ASTM C227)
b . Chemical Method (ASTM C289)
$1,200.00
$900.00
54. Wet Dry - 5 slabs (ASTMD5313, CRD-C 169)
$900.00
55. Soundness-Slab Method (ASTM D5240)
$900.00
c. 16 Day Mortar Bar Method (ASTM C1260, AASHTO T 303)
$900.00
56. Petrographic Examination (ASTM C295/ D 4992)
d. Remediation Trials with Fly Ash, Slag (C 1567)
$900.00
57. Specific Gravity/Absorption (ASTM D6473)
$1,600.00
$130.00
e. FAA EB 70 Pot. Acetate Method (De-Icer) (C 1260)
$1,000.00
58. Adsorption/Absorption Ratio
$130.00
f. 3-Point Remediation Curve (C1567)
$2,500.00
59. Ethylene Glycol Breakdown (Expansive Clays) (CRD-C 148)
$600.00
g 12 Month(+) Prism Method (C 1293)
$2,300.00
60. Sample Prep for items 53, 54, 55 (cut/ trim slabs) (ASTM D5121)
$350.00
h. 13 Week ICAR Modified (C 1293)
$1,200.00
i. 3-Point Remediation Curve (C 1293)
$5,600.00
Chemistry
61. Basic Elemental Analysis (ASTM C25) incl.: Al 2O3, Fe2O3, Ca, CaO
18. Alkali Carbonate Reactivity (ACR)
CaCO3, Mg, MgO, MgCO3, SiO2
a. Rock-Cylinder Method (C 586)
$1,200.00
b. Prism Method (C 1105)
$2,200.00
19. Petrographic Examination (C 295)
$135.00
Additional Element Charge
$27.00
62. Loss on Ignition - LOI (ASTM C25)
$27.00
63. Calcium Carbonate Equivalent-CCE (ASTM C25)
$55.00
a. Coarse Aggregate
$1,900.00
(Total Neutralizing Power - TNP)
b. Fine Aggregate
$2,300.00
64. Limestone Reactivity Test (ABB-FGD)
20. Effect of Organics (ASTM C87, AASHTO T 71)
$2,000.00
65. Prep Bulk Sample, crush and or pulverize (ASTM C50)
Long-Graded (Base) Quality Parameters
66. Prep for Fine Aggregate, pulverize to - #60 (ASTM C50)
21. Sieve Analysis; Long-graded, with Decant (ASTM C117/ C136, AASHTO T 11/T 27)
$145.00
67. Water Soluble Chloride Ion (ASTM D1411, AASHTO T 291)
22. Five Cycle Soundness, Long-graded, 10 size Fractions (ASTM C88, AASHTO T 104)
$530.00
68. Water Extractable Chloride Ion (ASTM C1524)
23. Los Angeles Abrasion (ASTM C131, AASHTO T 96, grading A)
$150.00
69. Silicon Dioxide, SiO2 (ODOT/ ASTM C146)
24. Atterberg Limits: Liquid Limit, Plastic Limit, & Plasticity Index ( D4318, T 89, 90)
$92.00
70. MSHA Incombustable Content (LOI)
25. Standard Proctor (moisture vs. density curve) ASTM D698, AASHTO T 99
$185.00
(refer to 2013 Lime & Limestone Fees for additional chemistry parameters)
26. Modified Proctor (moisture vs. density curve) ASTM D1557, AASHTO T 180
$185.00
MSE Wall Select Backfill testing parameters are presented on the "2013 Soil & Rock Fee Schedule"
Shipping Address:
Contact Person:
$800.00
$60.00
$27.00
$180.00
$180.00
$90.00
$64.00
Contact Information:
4518 Taylorsville Road, Dayton, OH 45424
Karl A. Fletcher, 937-236-8805
Manager
ext 322, cell: 937-750-2400, fax: 937-233-2016, kfletcher@bowser-morner.com
226 West Highland Ave., Springfield, IL 62704
Bill Sheftick, Manager
217-544-8378, cell: 217-544-8378, fax: 217-744-7625, wsheftick@bowser-morner.com
3016 Commerce Sq. S., Birmingham, AL 35210
Clark H. Lamb, Manager
205-956-8805, cell: 205-999-7792, fax: 205-956-8865, clamb@bowser-morner.com
Technical Director for all locations: James W. Fletcher, VP: cell: 937-974-2507 jfletcher@bowser-morner.com
BOWSER-MORNER, INC. - GEOTECHNICAL LABORATORY
AASHTO/ISO 17025 ACCREDITED • AASHTO R 18 ACCREDITED • USACE VALIDATED
2013 Laboratory Testing Fees - Bituminous (Asphalt) Materials
Sampling & Consultation
Sampling - Time (AASHTO T 40, T 168)
Sampling - Mileage (AASHTOTt 40, T 168)
Consultation, Senior Geologist/Engineer
Bituminous Mixtures (Asphaltic Concrete)
$60.00/Hour
$0.65/Mile
$130.00/Hour
12. Thickness of Asphalt Cores
$30.00
(ASTM D 3549)
13. Abson Recovery, Includes Viscosity
$2,000.00
(ASTM D 1856)
14 Release Agent Test
Aggregate Analysis
$400.00
(ODOT Procedure)
1. Gradation (ASTM C 136, T 27)
$72.00
2. Decantation (ASTM C 117, T 11)
$62.00
3. Specific Gravity and Absorption
$90.00
(ASTM C 127, C 128, T 85, T 84)
4. Percent Crushed (ASTM d 5821)
a. One-Face
$80.00
b. Two-Face
$100.00
Mix Design
15. Job Mix Formula Verification
Quote
16. Marshall Mix Design (JMF)
Quote
17. Retained Tensile (AASHTO T 283)
Quote
Liquid AC
Bituminous Mixtures (Asphaltic Concrete)
5. Molding Marshall Pills from Hot Mix
$360.00
Sample: Density, Stability & Flow
set of 3
(Field Sample) (ASTM D 1559, D 2726, AASHTO T 166, T 245)
6. Density, Stability, & Flow Only
$48.00
(Specimens brought in from field)
(ASTM D 1559, D2726, AASHTO T 166, T 245)
7. Extraction & Gradation (ASTM D 2172, D 5444, AASHTO T 164, T 30)
- Includes Ash Correction (AASHTO T 111)
a. Centrifuge (Method A)
$90.00
$90.00
20. Float Test (ASTM D 139, AASHTO T 50)
$140.00
21. Kinematic Viscosity (ASTM D 2170, AASHTO T 201)
$140.00
22. Vacuum Viscosity (ASTM D 2171, AASHTO T 202)
$140.00
23. Flash Point (ASTM D 92, AASHTO T 48)
$170.00
24. Solubility (ASTM D 2042, AASHTO T 44)
$140.00
25. Thin Film (ASTM D 1754, AASHTO T 179)
$300.00
26. Ductility (ASTM D 113, AASHTO T 51)
$300.00
27. Spot Test (AASHTO T 102)
$160.00
28. Softening Point (ASTM D 36, AASHTO T 53)
$160.00
$150.00
b. Reflux (Method B)
$240.00
c. Reflux without gradation, %AC only
$140.00
8. Max. Theoretical Specific Gravity, Rice
$130.00
(ASTM D 2041, AASHTO T 209)
9. Moisture & Volatile Distillates
18. Penetration (ASTM D 5, AASHTO T 49)
19. Specific Gravity (ASTM D 70, AASHTO T 228)
$410.00
(ASTM D 1461, AASHTO T 110)
Emulsified Asphalts (ASTM D 244, AASHTO T 59)
29. Water Content (by distillation)
$200.00
30. Residue & Oil Distillate
$200.00
31. Residue by Evaporation
$140.00
32. Particle Charge
$140.00
33. Saybolt Furol Viscosity
$170.00
34. Demulsibility
$170.00
10. Specific Gravity & Density-SSD Specimens (ASTM D 2726, AASHTO T 166) 35. Settlement
$140.00
a. Marshall Pills
$44.00
36. Cement Mixing
$170.00
b. Cores; Trimmed & Tested
$54.00
37. Sieve Test
$140.00
11. Specific Gravity & Density-Paraffin (ASTM D 1188, AASHTO T 275)
a. Marshall Pills
$64.00
b. Cores; Trimmed & Tested
$74.00
Shipping Address:
4518 Taylorsville Road, Dayton, OH 45424
Contact Person:
Karl A. Fletcher, Manager
Contact Information:
937-236-8805 ext 322, cell: 937-750-2400, fax: 937-233-2016, kfletcher@bowser-morner.com
226 West Highland Ave., Springfield, IL 62704
Bill Sheftick, Manager
217-544-8378, cell: 217-544-8378, fax: 217-744-7625, wsheftick@bowser-morner.com
3016 Commerce Sq. S., Birmingham, AL 35210
Clark H. Lamb, Manager
205-956-8805, cell: 205-999-7792, fax: 205-956-8865, clamb@bowser-morner.com
Technical Director for all locations: James W. Fletcher, VP: cell: 937-974-2507 jfletcher@bowser-morner.com
6/4/2013
BOWSER-MORNER, INC. - CONSTRUCTION MATERIALS LABORATORY
AASHTO/ISO 17025 ACCREDITED ● AASHTO R 18 ACCREDITED ● USACE VALIDATED
2013 Filter Media & Frac Sand Testing Fees
Sampling & Consultation
Frac Sand (API RP 19C, 56, 58, 60; ISO 13503-2)
Sampling - Time ASTM D50, D75
$60.00/Hour
Sampling - Mileage ASTM D50, D75
14. Sieve Analysis (API RP 19C sec. 6; RP 56-60 sec. 5, ISO 13503-2 sec. 6)
$82.00
15. Sphericity & Roundness (API RP 19C sec. 7, RP 56-60 sec. 6,
$92.00
$0.65/Mile
Consultation, Senior Geologist/Engineer
$130.00/Hour
ISO 13503-2 sec. 7)
(Krumbien/Sloss Index)
Sample Preparation (if required)
1. Necessary Sample Preparation (BMI SOP)
$60.00/Hour
a. Ledge Rock, etc., crush to test specimens
16. Acid Solubility, 12:3 HCl:HF (API RP 19C sec. 8; RP 56-60 sec. 7,
$140.00
ISO 13503-2 sec. 8)
b. Rock Core, split & archive representative half
$3.80/ft.
c. Rock Core, crush/reduce to test specimens
$3.80/ft.
d. Geologist Log
$3.80/ft.
e. Rock Core, log, split, crush (items 1b, 1c, & 1d)
$8.00/ft.
17. Turbidity (API RP 19C sec 9; RP 56-60 sec. 8, ISO 13503-2 sec. 9)
$110.00
18. Bulk, Apparent, & Absolute Density (API RP 19C sec 10,
$90.00
ISO 13503-2 sec. 10)
19. Crush Resistance Test (API RP 19C sec. 11, RP 56-60 sec 9,
$1,000.00
ISO 13503-2 sec 11) (up to six stress levels)
Granular Filter Media (AWWA B 100)
2. Sieve Analysis; Gradation (AWWA B100, sec. 5.3.4) (ASTM C 136)
20. Loss on Ignition (LOI) (API RP 19C sec 12, ISO 13503-2 sec 12)
$62.00
includes Effective Size (D10) & Uniformity Coefficient (UC)
a. Coarse, + No. 4 sieve (support gravel)
$82.00
b. Fine, - No. 4 sieve (sand & anthracite)
$82.00
21. X-Ray Diffraction, Sand Mineralogy (API RP 56-60, sec. 10)
$160.00
Chemistry
3. Decantation (percent minus No. 200, 0.075 mm) (ASTM C 117)
$62.00
4. Gravel Shape (AWWA B 100, sec. 5.3.2)
$82.00
22. Basic Elemental Analysis (ASTM C 25) incl.: Al 2O3, Fe2O3, Ca, CaO
(% fractured, flat, or elongated)
a. CaCO3, Mg, MgO, MgCO3, SiO2
$135.00
b. Additional Element Charge
$27.00
5. Specific Gravity (ASTM C 127, 128, AWWA B 100, sec. 5.3.3)
$88.00
23. % Silica Dioxide, SiO2, High Purity Silica Materials (ASTM C 146)
6. Acid Solubility (AWWA B 100, sec. 5.3.1)
$95.00
24. Prep Bulk Sample, crush and or pulverize (C 50)
$60.00
25. Prep for Fine Aggregate, pulverize to - #60 (C 50)
$27.00
7. Moh's Hardness (AWWA B100, sec. 5.3.5)
a. Plus No. 4 Material
$100.00
$70.00
b. Minus No. 4 Material, include prep
$160.00
8. Percent of Organic Impurities by Heavy Media (Gs @ 2.0)
$300.00
Misc. Parameters
26. Friability (Paint Can Method)
$100.00
(AWWA B 100, sec. 4.1.1.1 (3) note, ASTM C 123)
9. Organic Impurities by Colorimetric (ASTM C 40)
27. Micro Photographs
$30.00
28. Unit Weight (ASTM C 29)
$66.00
$64.00
(AWWA B100, sec. 4.1.1.2 & 4.1.1.3 notes.)
10. Heavy Media Separation (ASTM C 123)
AWWA B100 Tables 3 and 4 are presented for your convenience in order to
a. Sand/Anthracite Separation at 2.00 Gs
$340.00
b. Anthracite/Anthracite Separation at 1.45 & 1.95 Gs
$420.00
obtain test samples that will be in compliance with the applicable test methods.
AWWA B100 Table 4 Sampling of Bagged Filter Material
11. Caustic Solubility (ASTM D 1109)
$140.00
12. Loss on Ignition (LOI) (ASTM D 2974)
$62.00
13. Phase Determinations & Calcs.(Unit Weight, Porosity,
Void Ratio)
$160.00
(ASTM C 29, C 127, C 128, D 7263)
AWWA B100 Table 3 Minimum Size of Composite Sample
Max Size of Particles
Minimum Sample Size
Lot Size* (number of bags)
Minimum Sample Sizes
More than
Less than or equal to
(number of bags)
2
8
2
9
15
3
16
25
5
26
50
8
51
90
13
91
150
20
151
280
32
50
2 1/2-in.
63.0 mm
100 lbs
45.0 kg
281
500
1 1/2-in.
37.5 mm
70 lbs
32.0 kg
501
1,200
80
1-in.
25.4 mm
50 lbs
23.0 kg
1,201
3,200
125
3/4-in.
19.0 mm
30 lbs
14.0 kg
3,201
10,000
200
1/2-in.
12.5 mm
30 lbs
9.0 kg
10,001
35,000
315
9.5 mm
10 lbs
4.5 kg
35,001
150,000
500
3/8 & smaller
* AWWA B100, section 5.2.3 Table 4 note: Lot size at the producer's plant is the number of bags produced in a batch. Lot size at the jobsite is the number of bags of a particular
production batch delivered to the project site.
Shipping Address:
4518 Taylorsville Road, Dayton, OH 45424
Contact Person:
Karl A. Fletcher, Manager
Contact Information:
937-236-8805 ext 322, cell: 937-750-2400, fax: 937-233-2016, kfletcher@bowser-morner.com
226 West Highland Ave., Springfield, IL 62704
Bill Sheftick, Manager
217-544-8378, cell: 217-544-8378, fax: 217-744-7625, wsheftick@bowser-morner.com
3016 Commerce Sq. S., Birmingham, AL 35210
Clark H. Lamb, Manager
205-956-8805, cell: 205-999-7792, fax: 205-956-8865, clamb@bowser-morner.com
Technical Director for all locations: James W. Fletcher, VP: cell: 937-974-2507 jfletcher@bowser-morner.com
6/4/2013
BOWSER-MORNER, INC. - CONSTRUCTION MATERIALS LABORATORY
AASHTO/ISO 17025 ACCREDITED ● AASHTO R 18 ACCREDITED ● USACE VALIDATED
2013 CONCRETE TESTING FEES
Sampling & Consultation
Concrete Chemical Analysis
Sampling - Time
$60.00/Hour
Sampling - Mileage
$0.65/Mile
Consultation, Senior Geologist/Engineer
$130.00/Hour
Concrete Mix Design
*** DOT QCQA Mixes Quoted by Project ***
1. Complete Mix Design - Includes:
26. Acid Soluble Chloride Ion (C 1152)
$180.00
27. Water Soluble Chloride Ion (C 1218)
a. whole core
$180.00
b. profile (gradient), % per inch x 6-inches
$455.00
28. Acid Soluble Chloride Ion (T 260, sec. 5.2)
$180.00
29. Water Soluble Chloride Ion (T 260, sec. 5.3)
$180.00
$800.00/1st mix
Aggregate Gradation, Specific Gravity,
$600.00/ea
Five Cylinders Per Mix (standard 0.1 cu yd trial mix)
Basic Concrete Aggregate Tests (for complete aggregate
addl. mix
2. Verification Mix - Submitted by Client (5 Cylinders)
$600.00/mix
3. Airfield W/Cm Point (0.75 cu yd trial mix), includes
$3000.00/pt.
schedule, see 2012 Laboratory Testing Fees-Mineral Aggregates)
30. Sieve Analysis; Gradation (C 136, T 27)
(24) 6x12 cyls & (24) 6x6x20 beams, tested 6 ea. at
a. Coarse Aggregate (6 Sieves)
$72.00
3, 7, 14, & 28-days. Usually performed at 3 different W/Cm ratios
b. Fine Aggregate (6 Sieves)
$72.00
4. Water Cement Ratio Curve (3 Points)
$1600.00/set
31. Material Passing No. 200 Sieve/Decantation (C 117, T 11)
5. Time of Set, Penetration Resistance (C 403, T 197)
$180.00/set
32. Unit Weight (C 29, T 19)
6. Mix Design Using Retarder w/ Setting Time
$80.00/Hour
33. Los Angeles Abrasion (C131/C535, T 96)
$40.00 each
34. Specific Gravity and Absorption (C127/128, T 85/ T 84)
7. Additional Cylinders in Mix Design
8. Restrained Expansion Type K Concrete (C 878)
$1000.00/set of 3
9. Bleeding Test - as part of mix design (C 232, T 158)
$120.00
10. Concrete Mix Water Proof Test, (C 1602, T 26), incls control & test
mixes, time of sets, strengths, water sp gr, & % solids
$62.00
$66.00
$150.00
$90.00
35. Complete Quality Analysis (C 33) Includes: Soundness, LA Abrasion,
Deleterious Substances, Gradation, Unit Wt, Specific Gravity,
% Crushed, etc. See "Mineral Aggregates Fee Schedule"
$1,400.00
Concrete Physical Analysis
11. Length of Cores - Vernier Method (C174, T 148)
$44.00
12. Specific Gravity, Absorption, Voids (C642)
$54.00
13. Compressive Strength
a. Coarse Aggregate (20% Discount)
$1,200.00
b. Fine Aggregate (20% Discount)
$800.00
c. DOT Parameters, Additional
$200.00
36. Alkali Silica Reactivity (ASR)
a. 6 Month Mortar Bar Method (C 227)
$1,200.00
b . Chemical Method (C 289)
$900.00
$900.00
a. Cylinders (C 39, T 24)
$17.00
c. 14 Day Mortar Bar Method (C 1260, T 303)
b. Drilled Cores-Trimmed & Tested (C 42)
$58.00
d. Remediation Trials with Fly Ash, Slag (C 1567)
c. Modulus of Elasticity (C 469)
$95.00
e. FAA EB 70 Pot. Acetate Method (De-Icer) (C 1260)
$1,000.00
14. Flexural Strength
$900.00
f. 3-Point Remediation Curve (C1567)
$2,500.00
a. Center Point Load (C 293, T 177)
$50.00
g 12 Month(+) Prism Method (C 1293)
$2,300.00
b. Third Point Load (C 78, T 97)
$50.00
h. 13 Week ICAR Modified (C 1293)
$1,200.00
15. Splitting Tensile Strength (C 496, T 198)
$82.00
i. 3-Point Remediation Curve (C 1293)
$5,600.00
16. Creep in Compression
37. Alkali Carbonate Reactivity (ACR)
a. Creep Test Only-includes 5 control
& 5 test specimens (C 512)
$3400.00/set
b. AWWA Pipe Certification-includes
C512, C192, C39, C469, Report
17. Abrasion Resistance by Sandblasting (C 418)
18. Moisture Content
a. Rock-Cylinder Method (C 586)
$1,200.00
b. Prism Method (C 1105)
$2,200.00
38. Petrographic Examination (C 295)
$5000.00/mix
$1,000.00
a. Coarse Aggregate
$1,900.00
b. Fine Aggregate
$2,300.00
$20.00
19. Concrete Durability Factor Rapid Freeze-Thaw (C 666 A & B, T 161 CRD-C 114)
Concrete Sealer/Admixture Testing
a. Procedure A, USACE, 300 cycles, Dur. Factor
$2500.00/set of 3
39. Chloride Ion Permeability (C 1202, T 277)
b. Procedure B, DOT, 350 cycles, Expansion & DF
$2500.00/set of 3
40. Chloride Ion Penetration (T 259), controls & trials
c. beams already cast, mix not req'ed
$2000.00/set of 3
41. Scaling Resistance - 50 cycles (C 672), con. & trials
$2200.00/ set of 4
$600.00/ea.
a. each additional sealer/admixture, additional trial
$1200.00/ set of 2
d. each additional beam over 3 per set above
e. each additional cycle over 350 per set above
20. Drying Shrinkage - set of 3 prisms (C 157, T 160)
21. Chloride Ion Permeability (C 1202, T 277)
$6.00
$180.00
b. each additional cycle over 50 per set above
$580.00
$2200.00/ set of 4
$30.00/cycl/ set of 2
Supplies
$180.00
22. Chloride Ion Penetration (T 259)
$2200.00/ set of 4
42. Cylinder Molds
23. Scaling Resistance - 50 cycles (C 672)
$2200.00/ set of 4
43. Retaining Caps
$300.00/set
44. Pad Caps
$30.00 each
45. Slump Rod & Cone
46. Capping Compound
$100.00/set
$100.00/bag
24. Cut/Prep Core Specimen
25. Petrographic Examination (C 856)
Shipping Address:
4518 Taylorsville Road, Dayton, OH 45424
$60.00
Quote
Contact Person:
Karl A. Fletcher, Manager
$80.00/case
Contact Information:
937-236-8805 ext 322, cell: 937-750-2400, fax: 937-233-2016, kfletcher@bowser-morner.com
226 West Highland Ave., Springfield, IL 62704
Bill Sheftick, Manager
217-544-8378, cell: 217-544-8378, fax: 217-744-7625, wsheftick@bowser-morner.com
3016 Commerce Sq. S., Birmingham, AL 35210
Clark H. Lamb, Manager
205-956-8805, cell: 205-999-7792, fax: 205-956-8865, clamb@bowser-morner.com
Technical Director for all locations: James W. Fletcher, VP: cell: 937-974-2507 jfletcher@bowser-morner.com
6/4/2013
BOWSER-MORNER, INC. - CONSTRUCTION MATERIALS LABORATORY
AASHTO/ISO 17025 ACCREDITED ● AASHTO R 18 ACCREDITED ● USACE VALIDATED
2013 Laboratory Testing Fees - Stone and Masonry
Sampling & Consultation
Cement Mortar
Sampling - Time
$60.00/Hour
Sampling - Mileage
$0.65/Mile
Consultation, Senior Geologist/Engineer
$130.00/Hour
Concrete Masonry Units (Block) ASTM C 55 & C 90
1. Compressive Strength and Absorption (C 140)
$280.00/set of 6
2. Linear Shrinkage (C 426)
$550.00/set of 3
25. Mortar Mix Design - Includes gradation of sand,
strength cubes and water retention
$900.00 each
26. Time of Set, Vicat (C 191, T 131)
$160.00 each
27. Mortar Cube Compressive Strength (C 109, T 106)
$34.00 each
28. Drying Shrinkage (C 596)
$620.00/set
29. Expansion (C 1038)
$620.00/set
3. Fire Rating; NCMA & UL 618; Equivalent Thickness
Architectural Cast Stone ASTM C 1364
a. with strength & absorption (additional)
$100.00/set of 3
30. Compressive Strength (C 1194)
b. without strength & absorption
$240.00/set of 3
30. Absorption & Bulk Density (C 1195)
4. Prisms (C 1314)
$160.00/set
$160.00/set
32. Freeze Thaw (C 1364 sec. 5.4/ C 666 A)
a. 2-High
$260.00/set of 3
b. 3-High
$320.00/set of 3
c. Filled Cores, Additional
$120.00/set of 3
5. Bond Strength (C 952)
$410.00/set of 3
6. Freeze Thaw (C1262)
$1230.00/set of 5
7. Stain Test (C 641)
$260.00 each
8. Infrared Study to detect presence of Admixtures,
$3000.00/study
incls calibration curve
$2600.00/set
33. Linear Shrinkage (C 426)
$580.00/set
Dimension Stone (ASTM spec designations detailed below)
34. Absorption & Density (C 97)
$60.00 each
35. Modulus of Rupture (C 99)
$80.00 each
36. Compressive Strength (C 170)
$80.00 each
37. Abrasion Resistance (C 241)
$520.00 each
38. Flexural Strength (C 880)
9. Compressive Strength and Absorption (C 140)
$280.00/set of 6
10. Freeze-Thaw Durability (C 1262)
$80.00 each
39. Flexural Modulus of Elasticity (C 1352)
Concrete Retaining Wall Units ASTM C 1372
$1230.00/set of 5
40. Petrographic Examination (C 1721)
41. Free Silica for classification of "quartz-based" stone
$80.00 each
$1600.00 each
$150.00 each
(C 25, sec. 8)
Concrete Paving Units ASTM C 936
11. Compressive Strength and Absorption (C 140)
$280.00/set of 6
Note: Dimension stone testing is usually performed in sets of 3 or 5 depending
12. Freeze-Thaw Durability (C 1645)
$1230.00/set of 3
on the test parameter. In addition, some tests are performed wet, dry, parallel,
13. Abrasion Resistance (C 418)
$1000.00/set of 3
to the rift, and/or perpendicular to the rift.
Clay Masonry Units (Brick) ASTM C 216
ASTM Standard Specifications for Dimension Stone:
14. Compressive Strength (C 67)
$260.00/set of 5
C 503
Marble Dimension Stone
15. Absorption & Saturation Coefficient (C 67)
$260.00/set of 5
C 568
Limestone Dimension Stone
16. Modulus of Rupture; Flexure (C 67)
$270.00/set of 5
C 615
Granite Dimension Stone
17. Initial Rate of Absorption; Suction (C 67)
$84.00/set of 5
C 616
Quartz-Based Dimension Stone
18. Efflorescence (C 67)
$84.00/set of 5
C 629
Slate Dimension Stone
19. Freeze Thaw (C 67)
$2200.00/set of 5
C 1526
Serpentine Dimension Stone
20. Bond Strength (C 952)
$310.00/ set of 3
C 1527
Travertine Dimension Stone
Masonry Grout
21. Laboratory Trial Mix
Please contact us for a complete listing of number of test specimens
$870.00 each
22. Prism Compressive Strength (C 1019)
$34.00 each
23. Cube Compressive Strength (C 109)
$34.00 each
24. Grout Expansion/Shrinkage (C 1090)
$1200.00 each
Shipping Address:
4518 Taylorsville Road, Dayton, OH 45424
and dimensions required for the above testing
Members of the National Concrete Masonry Association (NCMA)
with NCMA Certified Laboratory Technicians
Contact Person:
Contact Information:
Karl A. Fletcher, Manager
937-236-8805 ext 322, cell: 937-750-2400, fax: 937-233-2016, kfletcher@bowser-morner.com
226 West Highland Ave., Springfield, IL 62704
Bill Sheftick, Manager
217-544-8378, cell: 217-544-8378, fax: 217-744-7625, wsheftick@bowser-morner.com
3016 Commerce Sq. S., Birmingham, AL 35210
Clark H. Lamb, Manager
205-956-8805, cell: 205-999-7792, fax: 205-956-8865, clamb@bowser-morner.com
Technical Director for all locations: James W. Fletcher, VP: cell: 937-974-2507 jfletcher@bowser-morner.com
6/4/2013
BOWSER-MORNER, INC. - CONSTRUCTION MATERIALS LABORATORY
AASHTO/ISO 17025 ACCREDITED ● AASHTO R 18 ACCREDITED ● USACE VALIDATED
2013 Laboratory Testing Fees - Lime & Limestone Chemical and Physical Testing (Non-Construction Uses)
Sampling & Consultation
Scrubber Stone Parameters
Sampling - Time ASTM D50, D75, AASHTO T 2
$60.00/Hour
Sampling - Mileage ASTM D50, D 75, AASHTO T 2
$0.65/Mile
Consultation, Senior Geologist/ Engineer/ Chemist
$130.00/Hour
15. Wet Sieve Analysis (C110, sec. 22)
Bulk Sample Preparation (rock core &/or large pieces)
1. Ledge Rock, etc., crush to test specimens
$82.00
16. Elemental Analysis (C25/ C 1271) per each element:
$60.00/Hour
a. calcium, reported as Ca, CaO, CaCO3
$27.00
b. magnesium, reported as Mg, MgO, MgCO3
$27.00
c. iron, reported as Fe, Fe2O3
$27.00
d. aluminum, reported as Al, Al2O3
$27.00
2. Rock Core, split & archive representative half
$3.80/ft.
e. silicon, reported as Si, SiO2
$27.00
3. Rock Core, crush to test specimens
$3.80/ft.
f. sulfur, reported as S, SO3
$27.00
g. residual oxides
$27.00
4. Geologist Log
$3.80/ft.
5. Rock Core, log, split, crush (items 2, 3, & 4)
$8.00/ft.
17. Calcium Carbonate Equivalent - CCE (C 25, sec. 33)
$55.00
(Total Neutralizing Power - TNP)
18. Loss on Ignition - LOI (C25, sec. 19)
Test Specimen Preparation (+ No. 4 reduced to - No. 60 mesh)
$27.00
6. Prep Bulk Sample (+ No. 4), crush and or pulverize (C 50)
$60.00
19. Limestone Reactivity Test (ABB-FGD, Alstom SOP)
7. Prep for Fine Aggregate (-#4), pulverize to - #60 (C 50)
$27.00
20. Acid Insoluble (C 25)
Aglime Quality Parameters
8. Wet Sieve Analysis (C110, sec. 22)
$82.00
$800.00
$27.00
21. Available Lime Index, Rapid Sugar (C 25, sec. 28)
$55.00
22. Carbon Dioxide, CO 2, by Schroetter's Alkalimeter
$75.00
23. Bond Work Index (BWI) - subcontracted to Metso or SGS
9. Elemental Analysis (C 25/ C 1271) per each element:
$1,350.00
ASTM C 110 Physical Test Parameters
a. calcium, reported as Ca, CaO, CaCO3
$27.00
24. Apparent Loose & Packed Density (sec. 19 & 20)
b. magnesium, reported as Mg, MgO, MgCO3
$27.00
25. Hunter Dry Brightness (sec. 12)
$200.00
c. iron, reported as Fe, Fe2O3
$27.00
26. Limestone Grindability (sec. 13)
$140.00
d. aluminum, reported as Al, Al2O3
$27.00
27. Particle Size by Sieve & Hydrometer (sec. 17)
$120.00
e. silicon, reported as Si, SiO2
$27.00
28. Residue & Sieve Analysis (sec. 15)
$120.00
f. residual oxides
$27.00
29. Settling Rate (sec. 14)
$120.00
$55.00
30. Specific Gravity (sec. 21)
10. Calcium Carbonate Equivalent - CCE (C 25, sec. 33)
(Total Neutralizing Power - TNP)
11. Loss on Ignition - LOI (C25, sec. 19)
$27.00
$50.00
$82.00
31. Water Retention (sec. 7)
$82.00
32. Wet Sieve Analysis (sec. 22)
$82.00
12. Relative Neutralizing Value (RNV) - Indiana Method
NC
33. Slaking Rate, Reactivity (sec. 11)
13. Effective Neutralizing Power (ENP) - Ohio Method
NC
34. Decrepitation Index (BGS TR WG/92/29)
$220.00
35. Oil Absorption, Coleman-Gardner Method (ASTM D 1483)
$120.00
(items 12. RNV & 13. ENP are calculations based upon items 8 & 10)
14. Acid Insoluble (C 25)
$27.00
$320.00
Other Common Elements (usually trace)
36. phosphorus, reported as P, P2O3
$27.00
37. sulfur, reported as S, SO3
$27.00
The following table recommends the number and weight of increments for
38. potassium, reported as K, K2O
$27.00
general purpose sampling and are based upon a 1000-ton lot size. To deter-
39. sodium, reported as Na, Na2O
$27.00
mine the number of increments recommended for a specific lot size use the
following equation: N2 = N1 [specific lot size (tons) / 1000 tons] 1/2
40. titanium, reported as Ti, TiO2
$27.00
41. manganese, reported as Mn, MnO2
$27.00
The following table describes the level of crushing and/or pulverizing required
where:
in order to prepare a proper test specimen for laboratory analysis:
N1 = minimum increments required, per 1000 ton lot, and
N2 = increments required for specified lot size
Levels of Preparation for Laboratory Testing
ASTM C 50 Table 1 - Recommended Number & Weight of Increments
as-submitted
for General Purpose Sampling
Particle Size
- 1/4 in.
minimum number of increments
+ 1/4 in. by - 3/4 in.
+ 3/4 in
crush to - No. 4
pulverize to - No. 60
rock core
$3.80/ ft
$27.00 ea. Interval
ledge rock
$60.00 ea.
$27.00 ea. sample
10
10
10
stockpile + No. 4
$60.00 ea.
$27.00 ea. sample
minimum weight of increment, lb
5
10
15
stockpile - No. 4
not applicable
$27.00 ea. sample
total minimum sample weight, lb
50
100
150
pulverized >#60
not applicable
$27.00 ea. sample
pulverized <#60
not applicable
not applicable (no charge)
Refer to ASTM C 50, "Sampling, Sample Preparation, Packaging, and Marking
of Lime and Limestone Products" for more detailed information and guidance.
Shipping Address:
4518 Taylorsville Road, Dayton, OH 45424
Contact Person:
Karl A. Fletcher, Manager
(total prep charge = crush fee plus pulverizing fee)
Contact Information:
937-236-8805 ext 322, cell: 937-750-2400, fax: 937-233-2016, kfletcher@bowser-morner.com
226 West Highland Ave., Springfield, IL 62704
Bill Sheftick, Manager
217-544-8378, cell: 217-544-8378, fax: 217-744-7625, wsheftick@bowser-morner.com
3016 Commerce Sq. S., Birmingham, AL 35210
Clark H. Lamb, Manager
205-956-8805, cell: 205-999-7792, fax: 205-956-8865, clamb@bowser-morner.com
Technical Director for all locations: James W. Fletcher, VP: cell: 937-974-2507 jfletcher@bowser-morner.com
6/4/2013