)
m
DH
R
-2
00
(D
ep
th
Ra
ng
e
40
00
ROTARY DRILLING COMPANY
DHR-200 (Depth Range 4000 m)
Drawworks
TF 25 (Romanian) - 1 1/4" drilling line - 6032 BAYLOL EDDY Current Brake
Mast
KANIZSA-300 (DKG) - mast 42 m (137') max. hook load with 10 lines = 200 tons
(440917 lb)
Substructure
Rig floor height from ground: 4,9 m (16') clear height: 3,6 m (11,8') casing load
capacity: 300 tons (661375 lb) setback capacity: 240 tons (529100 lb)
Power
2xCat 3512 and 1x12VFES 17/27 engines mechanical compound for distributio
to mud pumps and drawworks
Mud Pumps
1x P-1300 triplex (Ganz) and 1x CA-700 (Ganz-Marep) pumps driven from compound
Rotary Table
MRS 27 1/2", driven by drawworks through catworks
Hook/Block
MC-200 (Romanian) 5 sheaves 200 tons (440917 lb) capacity
Swivel
CH-200 (Romanian) 200 tons (440917 lb) capacity
Blowout Equipment
1x20 3/4"-3000 PSI Cameron "U" single ram
1x13 5/8"-5000 PSI Cameron "U" double ram
1x13 5/8"-5000 PSI Hydril "GK" annular
1x11" -5000 PSI Hydril "GK" annular, as required
BOP control system: One complete set of Koomey hydraulic BOP accumulator
and control unit
1x4 1/16" choke - 2 1/16" kill line manifold 5000 PSI with two adjustable manual
choke with control. Drilling spools and adapters according to requirements
Mud Tanks
4 mud tanks: 120 m3 (756 bbls) complete with LP mixing system, mud agitators
2 water tanks: 86 m3 (542 bbls)
Solids Control
2x Linear Swaco shale shakers, 1x CT3-300 desander,
1x10x4" cones mud cleaner (SWACO), 1x SWACO degasser, centrifuges
(SWACO) as required
Drill pipe
5" OD 19,5 lbs/ft - grade E/G NC-50
3 1/2" OD 13,3 lbs/ft - grade E/G NC-38, as required
Drill Collars
30x8" OD x 2 13/16" ID spiral 6 5/8" REG
30x6 1/2" OD x 2 13/16" ID spiral NC-50
30x4 3/4" OD 2 1/4" ID spiral NC-38
24x5" HWDP NC-50
24x3 1/2" HWDP NC-38, as required
Cabins
1x driller office, 1x tool pusher office, 2x crew cabins
1x workshop, 1x material stock
Other Equipment
Instrumentation - Indication and registration of main drilling paramteres.
Emergency generator, compressor station, diesel fuel tank, casing stabbing board,
fork lift, gas flare, dog house, pipe rack, kelly spinner, power slip, ezy torque,
spinning wrench, as required.
ID
EC
O-
SB
S
DI
R-
55
06
ROTARY DRILLING COMPANY
IDECO-SBS DIR 5506 mobile drilling and workover rig (Depth range 1800 m)
Rig self propelled mechanical-hydraulic, drive-in type, a modification of the original
IDECO DIR 5525 Rambler Rig.
Equipped with hydraulic telescopic 103 ft mast, double drum drawworks, transmission,
engine, and rotary drive unitized on a carrier.
Drawworks
H 37 ED IDECO 1" drilling line, hydromatic brake: Model: 122, Fawick Airflex
Clutch Catworks: Foster-Model 27 breakout and make - up cat heads
Mast
KM 103-212 GH Kwik-lift, hydraulically raised, telescoped mast: 31,5 m (103')
max. hook load with 8 lines = 92,8 tons (204405 lb)
Substructure
Rig floor height from ground 3,80 m (12,7') clear height: 3,20 m (11,8') casing
load capacity: 92,8 tons (204405 lb)
setback capacity: 95 tons (209435 lb)
Power
1x Cat 3406 DITA 380 HP mechanical compound to drawworks
Mud Pumps
1xPZ-8 (Gardner Denver) triplex pump (stand by) Powered by D 398 CAT.
Rotary Table
LR-175, 17 1/2" rotary table driven by drawworks
Hook/Block
IDECO shorty UTB-110-3-24 4 sheaves, 110 tons (242504 lb) capacity
Swivel
IDECO TL-120, 120 tons (264550 lb) capacity
Blowout Equipment
1x11"-5000 PSI Cameron "U" double ram
1x11"-5000 PSI Hydril "GK"annular
1x7 1/16"-5000 PSI Cameron "U" double ram
BOP control system: One complete set of Koomey hydraulic BOP accumulator
and control unit
One complete set of Cameron 4 1/16"x5000 PSI WP choke and kill manifold
Mud Tanks
3 mud tanks: 90 m3 (567 bbls) complete with LP mixing system, mud agitators
2 water tanks: 86 m3 (542 bbls)
Solids Control
2x Ganz double deck as required
Drill pipe
3 1/2" 13,3 lbs/ft grade F/G NC-38
2 7/8" 10,4 lbs/ft grade E/G NC-31
2 3/8" 6,65 lbs/ft grade E/G NC-26
Drill Collars
24x4 3/4" OD x 2 1/4" ID NC-38
24x3 1/2" OD x 1 1/2" ID NC-26
Cabins
1x driller office, 1x tool pusher office, 1x crew cabin
1x workshop, 1x material stock
Other Equipment
Instrumentation-indication and registration of main workover parameters,
compressor station, diesel fuel tank, gas flare, pipe racks, power slip, spinning
wrench etc. Sandline dia: 5/8", drum capacity: 4,800 m (15749')
80
6
DI
RSB
S
ID
EC
O-
IDECO-SBS DIR-806 mobile drilling and heavy workover rig
A self propelled machanical-hydraulic, drive-in rambler rig, complete in all respect for
drilling operations, with drawworks, mast, rig engines and ritary drive unitized on a self
propelled, tyre mounted carrier.
Drawworks
IDECO H-1000, 1 1/8" drilling line, auxiliary brake: Parmac 22 DP
spinning cat head: Forster 27B
Mast
IDECO-SBS KM 112 358 AGH, telescoped - mast 34 m (112'). max hook
load with 10 lines = 160 tons, (352733 lb) set back capacity: 95 tons
(209435 lb)
Substructure
Rig floor height from ground 3,80 m (12,7')
clear height: 3,6 m (11') casing load capacity: 200 tons (440917 lb)
setback capacity: 95 tons (209435 lb)
Power
2x Cat 3406 B DITA 480 HP each mechanical compound to drawworks
[compound: Allison converter CLBT 5861]
Mud Pumps
2x PZ-8 (Gardner Denver) triplex pumps (stand by), D-398 Powered
Rotary Table
IDECO 205 20,5" rotary table driven by drawworks
Hook/Block
IDECO shorty UTB-160-5-30/ 5 sheaves, 160 tons (352733 lb) capacity
Swivel
IDECO TL-200 200 tons (440917 lb) capacity
Blowout Equipment
1x13 5/8"-5000 PSI Cameron "U" double ram
1x13 5/8"-5000 PSI Cameron "A" double ram
1x11" -5000 PSI Cameron "U" double ram
1x11" -5000 PSI Hydril "GK" annular
1x7 1/16"-5000 PSI Cameron "U" double ram
BOP control system: One complete set of Koomey hydraulic BOP
accumulator and control unit. One complete set of Cameron
4 1/16"x5000 PSI WP choke and kill manifold
Mud Tanks
4 mud tanks: 120 m3 (75 bbls) complete with LP mixing system, mud agitators
2 water tanks: 86 m3 (542 bbls)
Solids Control
1x Baroid double deck and 1x ultra Cagle shale shakers, 1x CT2-300 desander,
1x10x4" cones mud cleaner (SWACO), 1x SWACO degasser, centrifuges
(SWACO) as required
Drill pipe
5" OD 19,5 lbs/ft grade E/G NC-50
3 1/2" OD 13,3 lbs/ft grade E/G NC-38,
Drill Collars
30x8" OD x 2 13/16" ID spiral 6 5/8" REG
30x6 1/2"x 2 13/16" ID spiral NC-50
30x4 3/4" OD 2 1/4" ID spiral NC-38
24x5" HWDP NC-50
Cabins
1x driller office, 1x tool pusher office, 1x crew cabin
1x workshop, 1x material stock
Other Equipment
Instrumentation-indication and registration of main workover parameters,
compressor station, diesel fuel tank, gas flare, pipe rack, power slip, spinning wrench,
hydraulic cathead, sand line dia 5/8", drum capacity
4800 m.
ID
EC
O-
SB
S
DI
R
-3
79
ROTARY DRILLING COMPANY
IDECO-SBS DIR-379
A self propelled machanical-hydraulic, drive-in rambler rig, complete in all respect for
drilling operations, with drawworks, mast, rig propelled, tyre mounted carrier.
Drawworks
H 35 ED IDECO 1" drilling line, Brake: PARKERSBURG 15" B
Mast
KM 90-180 GHA hydraulically raised telescoped up mast: 27 m (88,5')
Substructure
Rig floor height from ground: 3 m (10')
Clear height: 2,5 m (8'), Casing load capacity: 130 tons (286596 lb)
setback capacity: 95 tons (209435 lb)
Power
1 DEUTZ F12L 714, 265 HP mechanical compound to drawworks.
Mud Pumps
PAH-275 (Gardner Denver) triplex pump (Stand by) Powered by CAT-3408
Rotary Table
IDECO LR-175, 17 1/2" rotary table driven by drawworks.
Hook/Block
IDECO UTB-100-3-24, 4 sheaves, 100 tons (220458 lb) capacity
Swivel
IDECO TL 120, 120 tons (264550 lb) capacity
Blowout Equipment
1x7 1/16"-5000 PSI Cameron "U" double ram
1x7 1/16"-3000 PSI Hydril "GK" annular BOP
BOP control system: One complete set of Koomey hydraulic BOP accumulator
and control unit
One complete set of Cameron 4 1/16"x5000 PSI WP choke and kill manifold
Mud Tanks
3 active tanks: 90 m3 (567 bbls) complete with LP mixing system, mud agitators
2 water tanks: 86 m3 (542 bbls)
Solids Control
2x Ganz double deck as required
Drill pipe
2 7/8" 10,4 lbs/ft Grade E/G NC-31
2 3/8" 6,65 lbs/ft Grade E/G NC-26
Drill Collars
24x4 3/4" OD x 2 1/4" ID NC-38
24X3 1/2" OD x 1 1/2" ID NC-26
Cabins
1x driller office, 1x tool pusher office, 1x crew cabin
1x workshop, 1x material stock
Other Equipment
Instrumentation - indication and registration of main drilling parametres,
compressor station, diesel fuel tank, gas flare, pipe racks, power slips, spinning
wrench, as required. Sandline dia: 5/8", capacity 3500 m (11483,5') service
platform: 650 mm (2') - 3000 mm (10')
ID
EC
O-
SB
S
DI
R
-1
10
ROTARY DRILLING COMPANY
IDECO-SBS DIR-110
A self propelled machanical-hydraulic, drive-in rambler rig, complete in all respect for
drilling and workover operations, with drawworks, mast, rig engine and rotary drive unitized
on a self propelled, tyre mounted carrier.
Drawworks
IDECO-SBS Hydrair H35 CK drilling line 1" Brake Parkersburg 15"
Mast
IDECO-SBS KM 90 120 GH telescoped up. Height: 27,4 m (90')
Substructure
Rig floor height from ground: 3 m (10')
Clear height: 2,5 m (8'), Casing load capacity: 130 tons (286596 lb),
setback capacity: 95 tons (209435 lb)
Power
1x Cat. D-3306-B-DITA, 310 HP mechanical compound to drawworks Compound:
Allison CLT-754 transmission
Mud Pumps
PAH-275 (Gardner-Denver) triplex pump (Stand by), Powered by CAT 3408
Rotary Table
IDECO LR-175, 17 1/2" rotary table driven by drawworks
Hook/Block
IDECO UTB-75-2-24, 2 sheaves, 75 tons (165344 lb) capacity
Swivel
IDECO TL 120, 120 tons (264550 lb) capacity
Blowout Equipment
1x7 1/16"-5000 PSI Cameron "U" double ram
1x7 1/16"-3000 PSI Hydril "GK" annular BOP
BOP control system: One complete set of Koomey hydraulic BOP accumulator
and control unit
One complete set of Cameron 4 1/16"x5000 PSI WP choke and kill manifold
Mud Tanks
3 active tanks: 3x32=96 m3 (605 bbls) 86 m3 (542 bbs) water tank
capacity
Solids Control
2x Ganz double deck as required
Drill pipe
2 7/8" 10,4 lbs/ft Grade E/G NC-31
2 3/8" 6,65 lbs/ft Grade E/G NC-26
Drill Collars
24x4 3/4" OD x 2 1/4" ID NC-38
24X3 1/2" OD x 1 1/2" ID NC-26
Cabins
1x driller office, 1x tool pusher office, 1x crew cabin
1x workshop, 1x material stock
Other Equipment
Instrumentation - indication and registration of main drilling paramteres,
Compressor station, diesel fuel tank, gas flare, pipe rack, power slips, spinning
wrench, as required. Sandline dia 5/8", capacity: 3500 m (11483,5') service
platform: 650 mm (2') - 3000 mm (10')
IRI/IDECO ED 1200 - RIG 3
Drawworks
MODEL: IRI/IDECO type ED-1200,
two (2) DC motors type GE 752AR / 1000 HP each,
Continuous Power: 1200 HP,
Drum grooved for 1 1/4 “ drilling line,
Electric Brake: Baylor Model 5032
Mast
Model: IRI/IDECO HMF 142-650,
Height: 142’ (43.3 m), Base width: 21’ (6.4 m)
Static hook load capacity with 10 lines: 650,000 lbs (295 T)
Substructure
IRI/IDECO type swing-up,
Substructure height: 30’ (9 m)
Rotary table load capacity: 650,000 lbs (295 T)
Set Back load capacity: 350,000 lbs (159 T)
Total load capacity (set back + rotary) 1,000,000 lbs (454 T)
Power
Four (4) Diesel Engines: Caterpillar 3512,
Four (4) AC Generators: KATO 1200 KVA / 600 V / 50 Hz
SCR System: ROSS HILL Three (3) SCR
Mud Pumps
Two (2) IDECO T - 1300
Each Pump Powered by: two (2) DC motors type GE 752AR / 1000 HP each
Maximum Working pressure: 5,000 PSI (350 at)
Rotary Table
IRI/IDECO LR275 driven from drawworks
Opening 27 1/2”, Load rating 1,400,000 lbs (517 T)
Hook/Block
Travelling Block + Hook: IRI/IDECO type UTB-360-5-50
Rated capacity: 790,000 lbs (360 T)
Crown Block: IRI/IDECO Load Capacity: 820,000 lbs (372 T)
Swivel
IRI/IDECO type TL-300,
Load capacity: 600,000 lbs (275 T)
Working pressure: 5,000 PSI (350 at)
Blowout Equipment
Annular Preventer: Cameron type D 13 5/8”, 5,000 PSI (350 at)
Ram Preventers:
One (1) Single Ram 13 5/8” Cameron type U, 10,000 PSI (700 at)
One (1) Double Ram 13 5/8” Cameron type U, 10,000 PSI (700 at)
Choke manifold: Cameron 10,000 PSI (700 at)
BOP Accumulator: Koomey type 80 model MQ 200-11 SB3
Mud Tanks
Active Tanks: Three (3) total capacity: 1125 bbls. (180 m3)
Reserve Tanks: One (1) total capacity: 375 bbls. (60 m3)
Trip Tank: One (1) total capacity: 40 bbls. (6.5 m3)
Solids Control
Linear Motion Shale Shakers: Three (3) SWACO type ALS
Desander: SWACO type 2-12
Mud Cleaner: SWACO
Vacuum Degasser: SWACO
Other Equipment
M/D TOTCO Instrumentation, Automatic Driller (Satelite), Set of Fishing Tools,
Make Up Cathead (Foster 37-AH), Break Out Cathead (Foster 24-AH)
IR
I/I
DE
CO
ED
12
00
-R
IG
3
ROTARY DRILLING COMPANY