RiT Technologies Ltd.
24 Raoul Wallenberg St.
Tel Aviv, 68719, Israel
Tel: +972-3-6455151
Fax: +972-3-6474115
RiT SMARTen Cabling SystemTM
Installation Registration Instructions
In order to properly register and certify an installed SMARTen Cabling System site, RIT
requires some information describing the project.
Please include the following with every request for registration/certification.
a. RiT SMART CLASSix Cabling System Registration Document (3 pages,
attached).
b. Appendix A - Horizontal Cabling Records (forms attached). Complete a
separate sheet for each and every wiring rack at the communications
centers.
c. The latest tester’s calibration certificate.
d. A complete list of all RiT materials used (a copy of the purchase
order/invoice/packing list will suffice).
e. A block diagram showing the general arrangement of the campus subsystem
of the network.
f. A block diagram showing the general arrangement of the vertical subsystem
of the network for each building.
g. Complete field test results of all links at the installation. Each record must
include at least the following parameters:
Copper Links
 Communications outlet ID
 Patch panel port ID
 Horizontal cable ID
 Wire map results
 Length results
Fiber Optic Links
 Communications outlet ID
 Patch panel port ID
 Horizontal/vertical cable ID
 Attenuation results:
Multi Mode: (i) at 850 nm
(ii) at 1300 nm
Single Mode: (i) at 1310 nm
(ii) at 1550 nm
 Attenuation results









NEXT loss results, pair-to-pair,measured from local end
NEXT loss results, pair-to-pair,measured from far end
NEXT loss results, power sum,measured from local end
NEXT loss results, power sum,measured from far end
ACR results, pair-to-pair
ACR results, power sum
ELFEXT results, pair-to-pair
ELFEXT results, power sum
Return Loss
Page 1 of 6
RiT Technologies Ltd.
24 Raoul Wallenberg St.
Tel Aviv, 68719, Israel
Tel: +972-3-6455151
Fax: +972-3-6474115
 Propagation delay
 Delay skew
If a non RiT certified cable is used for the horizontal links the following is required for
certification:
1. 300 meters sample of the used cable.
2. The cable manufacturer test results for PSANEXT & PSAACRF from an independent
approved testing laboratory.
Test results should be submitted by e-mail or on a CD within 60 days of completion of the
site testing in the original Field Cabling Tester format to Registration@rit.co.il.
The field tester must be Level III compliant and capable of performing all tests specified
under latest draft of EIA/TIA 568-B.2. Test results must comply with latest draft of 100
Ohm 4-pair Category 6A Cabling EIA/TIA 568-B.2-1, or latest draft of ISO/IEC 11801 2nd
edition.
The following is a partial list of Field Testers capable of providing “Auto Test” of Category
6A as per the above document:
 Fluke - DSP-4000, DTX1800
 Agilent - WireScope 350
RiT reserves the right to have an on-site inspection of the installation performed by a RiT
representative prior to issuing a Registered Installation Certificate.
Please do not hesitate to contact your local RiT representative or RiT’s Technical Support
Department (techsupp@rit.co.il) for further assistance.
Page 2 of 6
RiT Technologies Ltd.
24 Raoul Wallenberg St.
Tel Aviv, 68719, Israel
Tel: +972-3-6455151
Fax: +972-3-6474115
Page 1 of
RiT SMARTen Cabling SystemTM
Registration Form
Installation Site Details
Company:
Address:
Contact Person
Telephone
E-mail
Fax:
Type of Business (Government, Hospital, Financial, etc.):
Installer Details
Company:
Address:
Contact Person
Telephone
E-mail
Fax:
Page 3 of 6
RiT Technologies Ltd.
24 Raoul Wallenberg St.
Tel Aviv, 68719, Israel
Tel: +972-3-6455151
Fax: +972-3-6474115
Page 2 of
Supervised By (details of the RIT Certified Installer responsible for the installation)
Name:
RIT Certified Installer Certificate Number:
Date Of Issue:
Company:
Address:
Telephone
E-mail
Fax:
I hereby declare that all links at the installation have successfully passed all tests
specified in Paragraph e. of the cover page of this document:
Signature:
Date:
Inspected By (details of the RIT representative who inspected the installation)
Name:
Company:
Address:
Telephone
E-mail
Fax:
I hereby declare that I have inspected the installation and field test results, and
verified that they meet the SMARTen Cabling System requirements.
Signature:
Date:
Page 4 of 6
RiT Technologies Ltd.
24 Raoul Wallenberg St.
Tel Aviv, 68719, Israel
Tel: +972-3-6455151
Fax: +972-3-6474115
Page 3 of
1. Details of cabling tester used:
Type/Model:
Serial Number:
Copy of latest calibration certificate must be attached.
2. Is a PatchView system installed?

YES

No
If yes, how many scanners?:
3. What are the initial applications supported over this system (i.e. Voice, 10BaseT,
100BaseT, Gigabit Ethernet, Token Ring, etc.?)
3. List any non-RIT SMARTen Cabling System components used as part of the
cabling system:
Component
Reason for Use
5. Remarks
This section for use by RIT Personnel
Comments
Registered by:
Registration Number:
Signature:
Date:
Page 5 of 6
RiT Technologies Ltd.
24 Raoul Wallenberg St.
Tel Aviv, 68719, Israel
Tel: +972-3-6455151
Fax: +972-3-6474115
Page 4 of
Appendix A - Horizontal Cabling Records
A separate form should be completed for each and every wiring rack at the
communications center.
Campus Name / ID:______________
Building Name / ID:______________
Item
Communications Center Name / ID__________
Wiring Rack Name / ID___________________
Manufacturer
A. Communications
Outlets
B. Work-Area Cords
C. Baluns/Adapters
at Work-Area
D. Horizontal Cables
(Quantity in Km)
E. Patch Panels
F. Patch Cords
G. Baluns/Adapters at
Communications
Center
Page 6 of 6
Part Number
Total Quantity