SECTION 10440
INTERIOR SIGNAGE
Display hidden notes to specifier by using “Tools”/”Options”/“View”/”Hidden Text”.
PART 1 GENERAL
1.1
SECTION INCLUDES
A.
1.2
1.3
Interior integrated modular signage system for directional, control, and informational
signage.
RELATED SECTIONS
A.
Section 03300 - Cast-in-Place Concrete.
B.
Section 04220 - Concrete Unit Masonry.
C.
Section 08110 - Steel Doors and Frames.
D.
Section 08210 - Wood Doors.
E.
Section 09260 - Gypsum Board Systems.
F.
Section 09510 - Acoustical Ceilings.
G.
Section 09900 - Painting.
H.
Section 09960 - Vinyl Wall Covering.
REFERENCES
A.
ANSI A117.1: Providing Accessibility and Usability for Physically Handicap
People, 1986 edition.
B.
Department of Justice, Office of the Attorney General, "Americans with Disabilities
Act", Public Law 101-336, (ADA).
10440-1
1.4
C.
Federal Register Part II, Architectural and Transportation Barriers Compliance
Board, 36 CFR Part 1191: Americans with Disabilities Act (ADA) Accessibility
Guidelines for Buildings and Facilities; Amendment to Final Guidelines, September
6, 1991.
D.
Federal Register Part III, Department of Justice, Office of the Attorney General, 28
CFR Part 36: Nondiscrimination on the Basis of Disability by Public
Accommodations and in Commercial Facilities, Final Rule, July 26, 1991.
DEFINITIONS
A.
1.5
Terms:
1.
Braille: Grade 2 Braille including 189 part-word or whole word contractions
in addition to Grade 1 Braille 63 characters. Tactile is required whenever
braille is required.
2.
Non-tactile: Letters and numbers on signs with width-to-height ratio between
3:5 and 1:1 and stroke width ratio between 1:5 and 1:10 using upper case "X"
to calculate ratios. Use type styles with medium weight; upper and lower case
lettering is permitted; serif typestyles are permitted.
3.
Symbols: Symbol itself is not required to be tactile but equivalent verbal
description is required both in tactile letters and braille.
4.
Tactile: 1/32 inch (0.80 mm) raised capital letters without serifs at least 5/8
inch (16 mm) height and not more than 2 inches (51 mm) height based on
upper case "X". Braille is required whenever tactile is required.
SYSTEM DESCRIPTION
A.
Signage under this section is intended to include items for identification, direction,
control, and information of building where installed as complete integrated system
from a single manufacturer.
B.
ADA design requirements:
1.
Signage requiring tactile graphics:
a.
Wall mounted signs designating permanent rooms and spaces such as,
room numbers and restroom, department, office, and fire exit
identifications.
b.
Individually applied characters are prohibited.
2.
Signage not requiring tactile graphics but which are required to comply to other
ADA requirements include signs providing direction to or information about
function of space such as, directional signs (signs with arrow), informational
signs (operating hours, policies, etc.), regulatory signs (no smoking, do not
enter), and ceiling and projected wall mount signs.
3.
Excluded signage:
a.
Exterior signs.
b.
Building directories.
c.
Menus.
10440-2
d.
1.6
Temporary signs, include personnel signs and tenant identification; suite
numbers are not considered temporary.
C.
ADA performance requirements:
1.
Tactile graphics signs mounting requirements:
a.
Single doors: Mount 60 inches (1524 mm) to sign centerline above
finish floor and on wall adjacent to latch side of door.
b.
Openings: Mount 60 inches (1524 mm) to sign centerline above finish
floor adjacent opening.
c.
No wall space adjacent latch side of door, opening, or double doors:
Mount 60 inches (1524 mm) to sign centerline above finish floor on
nearest adjacent wall.
D.
ADA disclaimer:
APCO supports the goal of making facilities accessible and has developed guidelines
in an effort to promote voluntary compliance. APCO provides information and
guidelines on the Americans with Disabilities Act (ADA) on a voluntary basis,
having used extreme care and high standards to assure accuracy in interpretation of
the law. However, all information, either written or verbal, is strictly an
interpretation and is presented with no warranty either expressed or implied. APCO
officers, staff, representatives, and/or consultants assume no legal responsibility for
the accuracy of presentations, comments or other ADA information. Neither is
liability assumed for the outcome of decisions, contracts, commitments or
obligations made on the basis of this information. APCO guidelines are taken from
the Department of Justice's final rules implementing Title III of the Americans with
Disabilities Act, printed in the Federal Register, 28 CFR, Part 36, 26 July 1991.
APCO recommends that anyone affected by ADA obtain a copy of The Americans
with Disabilities Act and consult their legal counsel.
SUBMITTALS
A.
Submit under provisions of Section 01300.
B.
Product Data: Manufacturer's data sheets on each product to be used, including:
1.
Manufacturer's product literature indicating units and designs selected.
2.
Evidence of manufacturer's computerized data retrieval program for tracking of
project for sign typography, message strip requirements and other pertinent
data from schedule input to final computerized typography on finished product.
3.
Preparation instructions and recommendations.
4.
Storage and handling requirements and recommendations.
5.
Installation methods.
C.
Samples: One full size sign sample illustrating the design, construction, colors,
typestyles, mounting method and other details as specified. Provide sample in small
size sign.
1.
Samples will be returned for use in Project.
10440-3
2.
1.7
Samples will not be returned for use in Project.
D.
Shop Drawings:
1.
Indicate materials, sizes, configurations, and applicable substrate mountings.
2.
Typography sample for message strips and headers copy.
3.
Artwork for special graphics.
4.
Artwork for special headers.
E.
Signage Schedule: Complete with location of each sign and the required copy/text.
F.
Sign Program Maintenance Plan:
1.
Manufacturer shall provide details of software and system of color coated
paper sign inserts allowing client to update and maintain signage graphics inhouse.
2.
Manufacturer shall provide details of an Online Reordering & Maintenance
Application whereby the client can submit sign reorders online and store
relevant project information such as sign type drawings, message schedules and
product instructions.
G.
Contract close out:
1.
Furnish appropriate checklist for aiding in reordering after Date of Substantial
Completion. Maintain computer schedule program for five years for ordering
new signage required by Owner.
2.
Maintenance data and cleaning requirements for exterior surfaces.
3.
Furnish one complete SignWord Pro software package Windows 3.0 or
Windows 95 or later, Windows NT 4.0 or later in Owner selected format for
PC type computer.
QUALITY ASSURANCE
A.
Manufacturer Qualifications:
1.
Work required under this section from manufacturer regularly engaged in work
of this type and scope for a minimum of 5 years.
2.
Maintain computer link between schedule input and computerized typography
production.
B.
Installer Qualifications: Trained and authorized by manufacturer for installations of
required scope and product.
C.
Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and
application workmanship.
1.
Finish areas designated by Architect.
2.
Do not proceed with remaining work until workmanship, graphics, and
installation are approved by Architect.
3.
Refinish mock-up as required to produce acceptable work.
10440-4
1.8
1.9
DELIVERY, STORAGE, AND HANDLING
A.
Package signs to prevent damage during shipment, handling, storage and installation.
Products are to remain in their original packaging (unless otherwise specified) until
removal is necessary for installation.
B.
If installation site is not ready for signage upon delivery, store signs in a dry, airconditioned environment.
C.
Handle signage in accordance with manufacturer’s instructions.
D.
Store and dispose of solvent-based materials, and materials used with solvent-based
materials, in accordance with requirements of local authorities having jurisdiction.
PROJECT CONDITIONS
A.
Maintain environmental conditions (temperature, humidity, and ventilation) within
limits recommended by manufacturer for optimum results. Do not install products
under environmental conditions outside manufacturer's absolute limits.
1.10 SEQUENCING AND SCHEDULING
A.
Schedule system installation after room finishes and fixtures have been completed.
1.11 WARRANTY
A.
Product Warranty: Provide manufacturer’s warranty against defects in materials and
workmanship for a period of one year.
PART 2 PRODUCTS
2.1
2.2
MANUFACTURERS
A.
Acceptable Manufacturer: APCO Signs; 388 Grant St. S.E., Atlanta, GA 30312.
ASD. Toll Free Tel: (877) 988-2726. Tel: (404) 688-9000. Fax: (404) 577-3847.
Email: sales@apcosigns.com. Web: http://www.apcosigns.com.
B.
Substitutions: Not permitted.
C.
Requests for substitutions will be considered in accordance with provisions of
Section 01600.
ACCEPTABLE PRODUCT
A.
FullView low-profile modular sign system as manufactured by APCO Signs.
10440-5
2.3
SYSTEM REQUIREMENTS
A.
General:
1.
Sign system shall feature solutions for all required sign types, including but not
limited to wall mounted personnel signs, work station personnel signs, primary
room identification, directories, directionals, overhead signs, projection wall
signs, free standing signs, restroom signs, regulatory and information signs,
stair signs and changeable slide conference room signs. All signs within the
system must feature the same family of components and convey a uniform look
throughout.
B.
Features:
1.
Updatability: Signs shall allow for easy updating of message inserts without
the need to replace the entire sign assembly. System shall offer a solution for
easy in-house updating of laser printed sign inserts for all sign types, including
personnel signs, directories and directional signs.
2.
Mounting: Signs shall accommodate installation via fully concealed
mechanical fasteners.
3.
Vandal Resistance: System must offer an option for a concealed locking
method to increase level of vandal resistance.
C.
Graphics and Typography: As selected from manufacturer’s standards. Reference
sign drawings.
D.
Colors and Finishes: As selected from manufacturer’s standards. Reference sign
drawings.
E.
ADA Compliance: Sign system shall comply with all current and applicable ADA
regulations, including requirements regarding which sign types require Braille/tactile
features, character heights, color contrast and installation locations and mounting
heights within the facility.
F.
Materials and Construction:
1.
Frames/Holders: Sign frame/holder assemblies shall be comprised of extruded
aluminum and/or aluminum composite materials and shall feature an overall
depth of 7/16” (12mm) or less.
2.
Braille / Tactile Components: PETG-backed photopolymer with raised
characters and Braille of minimum 1/32 inch (0.8 mm) depth/thickness.
Braille/tactile plaques shall contain a minimum of 40% recycled content.
3.
Substrate for Optional Decorative Laminate Backers: Any decorative laminate
backers such as Formica or Wilsonart shall be pressure adhered to
SiennaCORE, a natural fiber thermoset composite backer with a minimum
50% recycled content and comprised of materials from FSC certified sources.
Non-thermoset composite substrates such as PVC or acrylic will not be
accepted.
10440-6
4.
2.4
Fasteners: Signs shall be able to accommodate fully concealed mechanical
fasteners.
SIGN SYSTEM COMPONENTS
A.
Product: Low-Profile FullView Signs as Designed Using APCO Online Design
Studio: Reference drawings for location of colors, finishes, sizes and details.
1.
Low profile aluminum FullView sign holders with a wide range of graphics
inserts and display options. Reference drawings for colors, finishes, typestyles
and other details. Reference sign schedule for exact messages.
2.
Frame Configuration / Orientation:
a.
Vertical Configuration (Edge Profiles at Left/Right of Sign)
3.
Frame Assembly Type
a.
Standard (with Locking Pin. Inserts removed with suction cup tool)
b.
Inner-Access (Window pocket assembly. Inserts removed with sticky
note or similar)
4.
Aluminum Frame Edge Profile Shape
a.
Square (FVST-S)
b.
Radius (FVST-R)
c.
Bevel (FVST-B)
d.
Contour (FVST-C)
e.
Contour Ribbed (FVST-CR)
5.
Aluminum Frame Finish:
a.
Satin anodized aluminum finish.
b.
Bronze anodized aluminum finish.
c.
Painted Finish: Manufacturer’s Standard.
d.
Painted Finish: Custom Color.
6.
Core Sign Types: Other sign types, including ceiling and freestanding signs
may be included within the Project. See Signage Schedule and/or drawings for
details.
a.
Sign Type - eFV-A, ID - 3 inches h by 8-1/2 inches w (75 mm
by 216 mm), Description - Personnel Sign-SM.
b.
Sign Type - eFV-A2, 5-1/2 inches h by 8-1/2 inches w (140 mm by 216
mm), Description - Personnel Sign/ADA-LG.
c.
Sign Type - eFV-B, ID – 6-1/2 inches h by 8-1/2 inches w
(165 mm by 216 mm), Description - Room/Dept ID.
d.
Sign Type - eFV-C, ID - 3-1/2 inches h by 8-1/2 inches w (89
mm by 216 mm), Description - Mech/Elec/Etc. ID.
e.
Sign Type - eFV-D, ID – 9.68 inches h by 8-1/2 inches w
(245 mm by 216 mm), Description - Conf/Meeting Room.
f.
Sign Type - eFV-E, ID - 8-1/2 inches h by 8-1/2 inches w
(216 mm by 216), Description - Restroom Sign.
g.
Sign Type - eFV-F, ID - 6 inches h by 6 inches w (152
mm by 152 mm), Description - Room Number/ADA-SM.
h.
Sign Type - eFV-G, ID - 4-1/2 inches h by 8-1/2 inches w
(114 mm by 216 mm), Description - In Case of Fire.
10440-7
i.
7.
8.
Sign Type - eFV-H, ID - 8-1/2 inches h by 8-1/2 inches w
(216 mm by 216 mm), Description - Stair Sign.
j.
Sign Type – eFV-J, ID - 8-1/2 inches h by 8-1/2 inches w (26
mm by 216 mm), Description - Regulatory Sign.
k.
Sign Type - eFV-K, ID - 11 inches h by 11 inches w (279 mm
by 279 mm), Description - Emergency Plan.
l.
Sign Type - eFV-L, ID - 11 inches h by 8-1/2 inches w (279
mm by 216 mm), Description - Meetings/Notices Sign.
m.
Sign Type - eFV-M, ID - 17 inches h by 11 inches w (432 mm by 279
mm), Description - Primary Directional.
n.
Sign Type - eFV-M2, ID - 11 inches h by 17 inches w (279
mm by 432 mm), Description - Secondary Directional.
o.
Sign Type - eFV-N, ID - 22 inches h by 17 inches w (559 mm by 432
mm), Description - Directory.
Elements2 Decorative Backer Shape/Style:
a.
Shape/Style: Modular System Only with No Decorative Backer.
b.
Shape/Style: Arc1
c.
Shape/Style: Arc2
d.
Shape/Style: Arc3
e.
Shape/Style: Arc4
f.
Shape/Style: Scroll1
g.
Shape/Style: Scroll2
h.
Shape/Style: Scroll3
i.
Shape/Style: Scroll4
j.
Shape/Style: Ortho1
k.
Shape/Style: Ortho2
l.
Shape/Style: Ortho3
m.
Shape/Style: Ortho4
n.
Shape/Style: Blade1
o.
Shape/Style: Blade2
p.
Shape/Style: Blade3
q.
Shape/Style: Blade4
r.
Shape/Style: Peak1
s.
Shape/Style: Peak2
t.
Shape/Style: Curve1
u.
Shape/Style: Cloud1
Elements2 Decorative Backer Finishes/Patterns – Top Layer.
a.
Modular System Only – No Backers.
b.
Top Layer: L05 Zito.
c.
Top Layer: L03 Ginkgo.
d.
Top Layer: L04 Natural Leaves.
e.
Top Layer: L02 Coastal Grass.
f.
Top Layer: L01 Bamboo Rings.
g.
Top Layer: ACF Cool Frost.
h.
Top Layer: W01 Walnut.
i.
Top Layer: F04 Victorian Mahogany.
10440-8
9.
j.
Top Layer: F03 Cognac Maple.
k.
Top Layer: F02 Cherry Birch.
l.
Top Layer: W02 Monticello Maple.
m. Top Layer: F01 Amber Maple.
n.
Top Layer: F18 Glass Plastique.
o.
Top Layer: F19 Skylark Boomerang.
p.
Top Layer: F17 Charcoal Bloomberg.
q.
Top Layer: F16 Beluga Beige.
r.
Top Layer: F20 Tangle Seaweed.
s.
Top Layer: F21 Tangle Wheat.
t.
Top Layer: F09 Ubatuba Granite.
u.
Top Layer: F08 Labrador Granite.
v.
Top Layer: F07 Jamocha Granite.
w. Top Layer: W07 Mystique Night.
x.
Top Layer: F06 Colorado Slate.
y.
Top Layer: W06 Mystique Dusk.
z.
Top Layer: W04 Antique Topaz.
aa. Top Layer: W08 Sandy Topaz.
bb. Top Layer: W05 Greystone.
cc. Top Layer: W03 Amber Fusion.
dd. Top Layer: F05 Carrara Envision.
ee. Top Layer: W11 Saffron Tigris.
ff. Top Layer: W10 Natural Tigris.
gg. Top Layer: W09 Green Tigris.
hh. Top Layer: F14 Seagrass Strand.
ii.
Top Layer: F15 Wheat Strand.
jj.
Top Layer: F10 Bamboo Cane.
kk. Top Layer: F12 Cotton Paper.
ll.
Top Layer: F13 Fallen Leaves.
mm. Top Layer: F11 Burnished Glaze.
nn. Top Layer: Solid Color #1:
oo. Top Layer: Solid Color #2:
Elements2 Decorative Backer Finishes/Patterns – Bottom Layer.
pp. Bottom layer: L05 Zito.
qq. Bottom layer: L03 Ginkgo.
rr. Bottom layer: L04 Natural Leaves.
ss. Bottom layer: L02 Coastal Grass.
tt.
Bottom layer: L01 Bamboo Rings.
uu. Bottom layer: ACF Cool Frost.
vv. Bottom layer: W01 Walnut.
ww. Bottom layer: F04 Victorian Mahogany.
xx. Bottom layer: F03 Cognac Maple.
yy. Bottom layer: F02 Cherry Birch.
zz. Bottom layer: W02 Monticello Maple.
aaa. Bottom layer: F01 Amber Maple.
bbb. Bottom layer: F18 Glass Plastique.
10440-9
ccc. Bottom layer: F19 Skylark Boomerang.
ddd. Bottom layer: F17 Charcoal Bloomberg.
eee. Bottom layer: F16 Beluga Beige.
fff. Bottom layer: F20 Tangle Seaweed.
ggg. Bottom layer: F21 Tangle Wheat.
hhh. Bottom layer: F09 Ubatuba Granite.
iii. Bottom layer: F08 Labrador Granite.
jjj. Bottom layer: F07 Jamocha Granite.
kkk. Bottom layer: W07 Mystique Night.
lll. Bottom layer: F06 Colorado Slate.
mmm.
Bottom layer: W06 Mystique Dusk.
nnn. Bottom layer: W04 Antique Topaz.
ooo. Bottom layer: W08 Sandy Topaz.
ppp. Bottom layer: W05 Greystone.
qqq. Bottom layer: W03 Amber Fusion.
rrr. Bottom layer: F05 Carrara Envision.
sss. Bottom layer: W11 Saffron Tigris.
ttt. Bottom layer: W10 Natural Tigris.
uuu. Bottom layer: W09 Green Tigris.
vvv. Bottom layer: F14 Seagrass Strand.
www.
Bottom layer: F15 Wheat Strand.
xxx. Bottom layer: F10 Bamboo Cane.
yyy. Bottom layer: F12 Cotton Paper.
zzz. Bottom layer: F13 Fallen Leaves.
aaaa. Bottom layer: F11 Burnished Glaze.
bbbb. Bottom layer: Solid Color #1:
cccc. Bottom layer: Solid Color #2:
B.
Graphics:
1.
Type Sizes: Selected from manufacturer's standard sizes indicated in
SCHEDULE for particular units; meet ADA requirements for letter proportions
and sizes.
2.
Typography: Reference signage schedule and drawings for details. Font(s)
selected from manufacturer’s standards unless otherwise specified. All text
and graphics shall be a true representation of the typeface(s) and/or graphics
specified. Letter spacing and interline spacing shall be set by the manufacturer.
a.
Helvetica Regular (HR)
b.
Futura (FUT)
c.
Optima (O)
d.
Frutiger (F55)
e.
Typeface(s) as indicated in SCHEDULES Article and Drawings.
3.
Type Code(s): Uppercase.
4.
Type Code(s): Initial caps.
5.
Type Code(s): Combination.
6.
Type Code(s): Indicated in SCHEDULES Article.
7.
Imprint Colors: Selected by Architect from manufacturer's standard 40 non
10440-10
8.
9.
10.
glare screening ink colors per unit and indicated in SCHEDULE; color contrast
background colors in accord with ADA requirements.
Copy/Message List: Indicated in SCHEDULE.
Reference drawings and Signage Schedule for details.
All text and graphics shall be a true representation of typeface(s) and/or
graphics specified.
C.
Low-Profile FullView Signs as Custom Specified and Designed: Reference drawings
for location of colors, finishes, sizes and details. Reference signage schedule for sign
text.
1.
Desk/Counter-Top Signs – Vertical Frame Configuration
(Edge Profiles at Left/Right of Sign)
a.
Holder Size: 3 inches h by 6 inches w (75mm by 152mm), FV0306(V).
b.
Holder Size: 3 inches h by 8-1/2 inches w (75mm by 216mm),
FV0385(V).
c.
Holder Size: 4 inches h by 4 inches w (102mm by 102mm), FV0404(V).
d.
Holder Size: 6 inches h by 6 inches w (152mm by 152mm), FV0606(V).
e.
Holder Size: 8-1/2 inches h by 8-1/2 inches w (216mm by 216mm),
FV8585(V).
f.
Holder Size: 11 inches h by 8-1/2 inches w (279mm by 216mm),
FV1185(V).
g.
Assembly Type
1)
Standard
2)
Inner-Access
.Desk Sign Insert: Non-glare clear lens with subsurface graphics insert.
1)
Subsurface laser printed paper insert.
2)
Subsurface inkjet printed insert with protective laminate.
i.
Desk Sign Insert: Solid color insert with silkscreen printed graphics.
j.
Desk Sign Insert: Decorative wood laminate insert.
k.
Desk Sign Insert: Decorative metal insert.
2.
Desk/Counter-Top Signs – Horizontal Frame Configuration
(Edge Profiles at Top/Bottom of Sign)
a.
Holder Size: 3 inches h by 6 inches w (75mm by 152mm), FV0306(H).
b.
Holder Size: 3 inches h by 8-1/2 inches w (75mm by 216mm),
FV0385(H).
c.
Holder Size: 4 inches h by 4 inches w (102mm by 102mm), FV0404(H).
d.
Holder Size: 6 inches h by 6 inches w (152mm by 152mm), FV0606(H).
e.
Holder Size: 8-1/2 inches h by 8-1/2 inches w (216mm by 216mm),
FV8585(H).
f.
Holder Size: 11 inches h by 8-1/2 inches w (279mm by 216mm),
FV1185(H).
g.
Assembly Type:
1)
Standard
2)
Inner-Access
h.
Desk Sign Insert: Non-glare clear lens with subsurface graphics insert.
1)
Subsurface laser printed paper insert.
10440-11
3.
4.
2)
Subsurface inkjet printed insert with protective laminate.
i.
Desk Sign Insert: Solid color insert with silk screen printed graphics.
j.
Desk Sign Insert: Decorative wood laminate insert.
k.
Desk Sign Insert: Decorative metal insert.
Workstation Signs – Vertical Frame Configuration
(Edge Profiles at Left/Right of Sign)
a.
Holder Size: 3 inches h by 6 inches w (75mm by 152mm), FV0306(V).
b.
Holder Size: 3 inches h x 8-1/2 inches w (75mm by 216mm),
FV0385(V).
c.
Holder Size: 4 inches h x 4 inches w (102mm by 102mm), FV0404(V).
d.
Holder Size: 6 inches h x 6 inches w (152mm by 152mm), FV0606(V).
e.
Assembly Type:
1)
Standard
2)
Inner-Access
f.
Holder Attachment Method to Workstation: Formed aluminum clip to fit
over the top of workstation.
g.
Holder Attachment Method to Workstation: Concealed PinMount for
fabric panel surfaces.
h.
Workstation Sign Insert: Non-glare clear lens with subsurface graphics
insert.
1)
Subsurface laser printed paper insert.
2)
Subsurface inkjet printed insert with protective laminate.
i.
Workstation Sign Insert: Solid color insert with silk screen printed
graphics.
j.
Workstation Sign Insert: Decorative wood laminate insert.
k.
Workstation Sign Insert: Decorative metal insert.
Workstation Signs – Horizontal Frame Configuration
(Edge Profiles at Top/Bottom of Sign)
a.
Holder Size: 3 inches h by 6 inches w (75mm by 152mm), FV0306(H).
b.
Holder Size: 3 inches h x 8-1/2 inches w (75mm by 216mm),
FV0385(H).
c.
Holder Size: 4 inches h x 4 inches w (102mm by 102mm), FV0404(H).
d.
Holder Size: 6 inches h x 6 inches w (152mm by 152mm), FV0606(H).
e.
Assembly Type:
1)
Standard
2)
Inner-Access
f.
Holder Attachment Method to Workstation: Formed aluminum clip to fit
over the top of workstation.
g.
Holder Attachment Method to Workstation: Concealed PinMount for
fabric panel surfaces.
h.
Workstation Sign Insert: Non-glare clear lens with subsurface graphics
insert.
1)
Subsurface laser printed paper insert.
2)
Subsurface inkjet printed insert with protective laminate.
i.
Workstation Sign Insert: Solid color insert with silk screen printed
graphics.
10440-12
5.
j.
Workstation Sign Insert: Decorative wood laminate insert.
k.
Workstation Sign Insert: Decorative metal insert.
Wall Mount Signs – Vertical Configuration
(Edge Profiles at Left/Right of Sign)
a.
Holder Size: 4 inches h by 4 inches w (102mm by 102mm), FV0404(V).
b.
Holder Size: 6 inches h by 4 inches w (152mm by 102mm), FV0604(V).
c.
Holder Size: 8 inches h by 4 inches w (203mm by 102mm), FV0804(V).
d.
Holder Size: 3 inches h by 6 inches w (75mm by 152mm), FV0306(V).
e.
Holder Size: 6 inches h by 6 inches w (152mm by 152mm), FV0606(V).
f.
Holder Size: 7.062 inches h by 6 inches w (179mm by 152mm),
FV0706(V)SL, with Slider Band.
g.
Holder Size: 8 inches h by 6 inches w (203mm by 152mm), FV0806(V).
h.
Holder Size: 9 inches h by 6 inches w (229mm by 152mm),
FV0906(V)A2.0SL, with ADA and Slider Band.
i.
Holder Size: 10 inches h by 6 inches w (254mm by 152mm),
FV1006(V).
j.
Holder Size: 3 inches h by 8-1/2 inches w (75mm by 216mm),
FV0385(V).
k.
Holder Size: 4-1/2 inches h by 8-1/2 inches w (114mm by 216mm),
FV4585(V).
l.
Holder Size: 5-1/2 inches h by 8-1/2 inches w (140mm by 216mm),
FV5585(V).
m. Holder Size: 6-1/2 inches h by 8-1/2 inches w (165mm by 216mm),
FV6585(V).
n.
Holder Size: 8-1/2 inches h b 8-1/2 inches w (216mm by 216mm),
FV8585(V).
o.
Holder Size: 9.68 inches h by 8-1/2 inches w (246mm by 216mm),
FV9685(V)SL, with Slider Band
p.
Holder Size: 11 inches h by 8-1/2 inches w (279mm by 216mm),
FV1185(V).
q.
Holder Size: 12 inches h by 8-1/2 inches w (305mm by 216mm),
FV1285(V)A2.5SL, with ADA and Slider Band.
r.
Holder Size: 14 inches h by 8-1/2 inches w (356mm by 216mm),
FV1485(V).
s.
Holder Size: 15 inches h by 8-1/2 inches w (381mm by 216mm),
FV1585(V)A3.0SL, with ADA and Slider Band.
t.
Holder Size: 8-1/2 inches h by 11 inches w (216mm by 279mm),
FV8511(V).
u.
Holder Size: 11 inches h by 11 inches w (279mm by 279mm),
FV1111(V).
v.
Holder Size: 12 inches h by 11 inches w (305mm by 279mm),
FV1211(V).
w. Holder Size: 14 inches h by 11 inches w (356mm by 279mm),
FV1411(V).
x.
Holder Size: 17 inches h by 11 inches w (432mm by 279mm),
FV1711(V).
10440-13
y.
6.
Holder Size: 8-1/2 inches h by 14 inches w (216mm by 356mm),
FV8514(V).
z.
Holder Size: 11 inches h by 17 inches w (279mm by 432mm),
FV1117(V).
aa. Holder Size: 14 inches h by 17 inches w (356mm by 279mm),
FV1417(V).
bb. Holder Size: 17 inches h by 17 inches w (432mm by 432mm),
FV1717(V)MF.
cc. Holder Size: 22 inches h by 17 inches w (559mm by 432mm),
FV2217(V)MF.
dd. Holder Size: 24 inches h by 18 inches w (610mm by 457mm),
FV2418(V)MF.
ee. Holder Size: 36 inches h by 18 inches w (914mm by 457mm),
FV3618(V)MF.
ff. Holder Size: 22 inches h by 22 inches w (559mm by 559mm),
FV2222(V)MF.
gg. Holder Size: 30 inches h by 22 inches w (762mm by 559mm),
FV3022(V)MF.
hh. Assembly Type
1)
Standard
2)
Inner-Access (maximum size – 17 inch h by 11 inch w)
ii.
Holder Attachment Method to Wall Surface: Concealed mechanical
fasteners. (Not compatible with FullView Inner-Access assembly)
jj.
Holder Attachment Method to Wall Surface: Double-sided vinyl tape.
kk. Holder Attachment Method to Wall Surface: Double-sided vinyl tape and
silicon adhesive.
ll.
Wall Mount Sign Insert: Non-glare clear lens with subsurface graphics
insert.
1)
Subsurface laser printed paper insert.
2)
Subsurface inkjet printed insert with protective laminate.
mm. Wall Mount Sign Insert: Solid color insert with silk screen printed
graphics
nn. Wall Mount Sign Insert: Solid color photopolymer Braille/tactile plaque
at bottom of sign with 1/16” divider bar.
oo. Wall Mount Sign Insert: Solid color photopolymer Braille/tactile plaque
& Slider Band combo at bottom of sign with 1/16” divider bar.
pp. Wall Mount Sign Insert: Solid color photopolymer Braille/tactile plaque.
qq. Wall Mount Sign Insert: Clear photopolymer Braille/tactile plaque with
subsurface graphics insert.
rr. Wall Mount Sign Insert: Slider Band.
ss. Wall Mount Sign Insert: Decorative wood laminate insert.
tt.
Wall Mount Sign Insert: Decorative metal insert at bottom of sign.
Wall Mount Signs – Horizontal Configuration
(Edge Profiles at Top/Bottom of Sign)
a.
Holder Size: 3 inches h by 6 inches w (75mm by 152mm), FV0306(H).
10440-14
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
l.
m.
n.
o.
p.
q.
r.
s.
t.
u.
v.
w.
x.
y.
Holder Size: 3 inches h by 8-1/2 inches w (75mm by 216mm),
FV0385(H).
Holder Size: 4 inches h by 4 inches w (102mm by 102mm), FV0404(H).
Holder Size: 4 inches h by 6 inches w (102mm by 152mm), FV0406(H).
Holder Size: 4 inches h by 8 inches w (102mm by 203mm), FV0408(H).
Holder Size: 4 inches h by 8-1/2 inches w (102mm by 216mm),
FV0485(H).
Holder Size: 4 inches h by 12 inches w (102mm by 305mm),
FV0412(H).
Holder Size: 6 inches h by 6 inches w (152mm by 152mm), FV0606(H).
Holder Size: 6 inches h by 8 inches w (152mm by 203mm), FV0608(H).
Holder Size: 6 inches h by 8-1/2 inches w (152mm by 216mm),
FV0685(H).
Holder Size: 6 inches h by 12 inches w (152mm by 305mm),
FV0612(H).
Holder Size: 6 inches h by 17 inches w (152mm by 432mm),
FV0617(H).
Holder Size: 8-1/2 inches h by 11 inches w (216mm by 279mm),
FV8511(H).
Holder Size: 8-1/2 inches by 14 inches w (216mm by 356mm),
FV8514(H).
Holder Size: 8-1/2 inches by 17 inches w (216mm by 432mm),
FV8517(H).
Holder Size: 11 inches by 8-1/2 inches w (279mm by 216mm),
FV1185(H).
Holder Size: 11 inches h by 11 inches w (279mm by 279mm),
FV1111(H).
Holder Size: 11 inches h by 17 inches w (279mm by 432mm),
FV1117(H).
Assembly Type
1)
Standard
2)
Inner-Access (maximum size – 11 inch h by 17 inch w)
Holder Attachment Method to Wall Surface: Concealed mechanical
fasteners. (Not compatible with FullView Inner-Access assembly)
Holder Attachment Method to Wall Surface: Double-sided vinyl tape.
Holder Attachment Method to Wall Surface: Double-sided vinyl tape &
silicon adhesive.
Wall Mount Sign Insert: Non-glare clear lens with subsurface graphics
insert.
1)
Subsurface laser printed paper insert.
2)
Subsurface inkjet printed insert with protective laminate.
Wall Mount Sign Insert: Solid color insert with silk screen printed
graphics
Wall Mount Sign Insert: Solid color photopolymer Braille/tactile plaque
with silk screen printed graphics.
10440-15
z.
7.
8.
Wall Mount Sign Insert: Solid color photopolymer Braille/tactile band
laminated to non-glare clear lens with subsurface graphics insert.
aa. Wall Mount Sign Insert: Clear photopolymer Braille/tactile plaque with
subsurface graphics insert.
bb. Wall Mount Sign Insert: Decorative wood laminate insert.
Projection Wall Mount Signs - Double-Sided – Standard Assembly –
Vertical Configuration – (Edge Profiles at Left/Right of Sign)
a.
Holder Size: 6 inches h by 6 inches w (152mm by 152mm),
FV0606(V)PWM.
b.
Holder Size: 8-1/2 inches h by 8-1/2 inches w (216mm by 216mm),
FV8585(V)PWM.
c.
Holder Size: 11 inches h by 8-1/2 inches w (279mm by 216mm),
FV1185(V)PWM.
d.
Holder Size: 11 inches h by 11 inches w (279mm by 279mm),
FV1111(V)PWM.
e.
Holder Size: 17 inches h by 11 inches w (432mm by 279mm),
FV1711(V)PWM.
f.
Projection Wall Mount Sign Insert: Non-glare clear lens with subsurface
graphics insert.
1)
Subsurface laser printed paper insert.
2)
Subsurface inkjet printed insert with protective laminate.
g.
Projection Wall Mount Sign Insert: Solid color insert with silk screen
printed graphics.
h.
Projection Wall Mount Sign Insert: Decorative wood laminate insert.
i.
Projection Wall Mount Sign Insert: Decorative metal insert.
Overhead Signs – Standard Assembly - Horizontal Configuration
(Edge Profiles at Top/Bottom of Sign)
a.
Holder Size: 8 inches h by 24 inches w (203mm by 610mm),
FV0824(H).
b.
Holder Size: 8 inches h by 36 inches w (203mm by 914mm),
FV0836(H).
c.
Holder Size: 8 inches h by 48 inches w (203mm by 1219mm),
FV0848(H).
d.
Holder Size: 12 inches h by 24 inches w (305mm by 610mm),
FV1224(H).
e.
Holder Size: 12 inches h by 36 inches w (305mm by 914mm),
FV1236(H).
f.
Holder Size: 12 inches h by 48 inches w (305mm by 1219mm),
FV1248(H).
g.
Holder Size: 12 inches h by 60 inches w (305mm by 1524mm),
FV1260(H).
h.
Holder Attachment Method to Ceiling Surface: Flush Mount via Modular
Aluminum Bracket.
i.
Holder Attachment Method to Ceiling Surface: Suspended via Wire.
j.
Holder Attachment Method to Ceiling Surface: Wall Mount (SingleSided).
10440-16
k.
9.
10.
11.
Ceiling Sign Insert: Non-glare clear lens with subsurface graphics insert.
1)
Subsurface inkjet printed insert with protective laminate.
l.
Ceiling Sign Insert: Solid color insert with silkscreen printed graphics.
m. Ceiling Sign Insert: Decorative wood laminate insert.
n.
Ceiling Sign Insert: Decorative metal insert.
Kiosks: Double-Sided Kiosk with Aluminum Edge Profiles, Updatable Display
Options and a Powder-Coated Steel Baseplate
a.
Holder/Kiosk Width(s) - 11 inches (279 mm) (FVKSK11):
1)
48 inches (1219 mm) Height.
2)
60 inches (1524 mm) Height.
b.
Holder/Kiosk Size(s) - 17 inches (432 mm) (FVKSK17):
1)
60 inches (1524 mm) Height.
2)
66 inches (1676 mm) Height.
3)
72 inches (1829 mm) Height. (recommended anchor mounting to
floor surface)
c.
Holder/Kiosk Size(s) - 22 inches (559 mm) (FVKSK22):
1)
66 inches (1676 mm) Height.
2)
72 inches (1829 mm) Height (recommended anchor mounting to
floor surface).
3)
84 inches (2134 mm) Height (recommended anchor mounting to
floor surface).
d.
Kiosk Sign Insert: Non-glare clear lens with subsurface graphics insert.
1)
Subsurface laser printed paper insert.
2)
Subsurface inkjet printed insert with protective laminate.
e.
Kiosk Sign Insert: Solid color insert with silk screen printed graphics.
f.
Kiosk Sign Insert: Literature Holder(s).
g.
Kiosk Sign Insert: Optional decorative wood laminate insert.
h.
Kiosk Sign Insert: Optional decorative metal insert.
FullView Aluminum Holder Finish:
a.
Satin anodized aluminum.
b.
Bronze anodized aluminum
c.
Painted Finish:
1)
Manufacturer’s Standard: Refer to drawings and schedule.
2)
Custom Color: Refer to drawings and schedule.
Elements2 Decorative Backer Shape/Style:
a.
Shape/Style: Modular System Only with No Decorative Backer.
b.
Shape/Style: Arc1
c.
Shape/Style: Arc2
d.
Shape/Style: Arc3
e.
Shape/Style: Arc4
f.
Shape/Style: Scroll1
g.
Shape/Style: Scroll2
h.
Shape/Style: Scroll3
i.
Shape/Style: Scroll4
j.
Shape/Style: Ortho1
k.
Shape/Style: Ortho2
10440-17
12.
l.
Shape/Style: Ortho3
m.
Shape/Style: Ortho4
n.
Shape/Style: Blade1
o.
Shape/Style: Blade2
p.
Shape/Style: Blade3
q.
Shape/Style: Blade4
r.
Shape/Style: Peak1
s.
Shape/Style: Peak2
t.
Shape/Style: Curve1
u.
Shape/Style: Cloud1
Elements2 Decorative Backer Finishes/Patterns – Top Layer.
d.
Modular System Only – No Backers.
e.
Top Layer: L05 Zito.
f.
Top Layer: L03 Ginkgo.
g.
Top Layer: L04 Natural Leaves.
h.
Top Layer: L02 Coastal Grass.
i.
Top Layer: L01 Bamboo Rings.
j.
Top Layer: ACF Cool Frost.
k.
Top Layer: W01 Walnut.
l.
Top Layer: F04 Victorian Mahogany.
m. Top Layer: F03 Cognac Maple.
n.
Top Layer: F02 Cherry Birch.
o.
Top Layer: W02 Monticello Maple.
p.
Top Layer: F01 Amber Maple.
q.
Top Layer: F18 Glass Plastique.
r.
Top Layer: F19 Skylark Boomerang.
s.
Top Layer: F17 Charcoal Bloomberg.
t.
Top Layer: F16 Beluga Beige.
u.
Top Layer: F20 Tangle Seaweed.
v.
Top Layer: F21 Tangle Wheat.
w. Top Layer: F09 Ubatuba Granite.
x.
Top Layer: F08 Labrador Granite.
y.
Top Layer: F07 Jamocha Granite.
z.
Top Layer: W07 Mystique Night.
aa. Top Layer: F06 Colorado Slate.
bb. Top Layer: W06 Mystique Dusk.
cc. Top Layer: W04 Antique Topaz.
dd. Top Layer: W08 Sandy Topaz.
ee. Top Layer: W05 Greystone.
ff. Top Layer: W03 Amber Fusion.
gg. Top Layer: F05 Carrara Envision.
hh. Top Layer: W11 Saffron Tigris.
ii.
Top Layer: W10 Natural Tigris.
jj.
Top Layer: W09 Green Tigris.
kk. Top Layer: F14 Seagrass Strand.
ll.
Top Layer: F15 Wheat Strand.
10440-18
13.
mm. Top Layer: F10 Bamboo Cane.
nn. Top Layer: F12 Cotton Paper.
oo. Top Layer: F13 Fallen Leaves.
pp. Top Layer: F11 Burnished Glaze.
qq. Top Layer: Solid Color #1:
rr. Top Layer: Solid Color #2:
Elements2 Decorative Backer Finishes/Patterns – Bottom Layer.
ss. Bottom layer: L05 Zito.
tt.
Bottom layer: L03 Ginkgo.
uu. Bottom layer: L04 Natural Leaves.
vv. Bottom layer: L02 Coastal Grass.
ww. Bottom layer: L01 Bamboo Rings.
xx. Bottom layer: ACF Cool Frost.
yy. Bottom layer: W01 Walnut.
zz. Bottom layer: F04 Victorian Mahogany.
aaa. Bottom layer: F03 Cognac Maple.
bbb. Bottom layer: F02 Cherry Birch.
ccc. Bottom layer: W02 Monticello Maple.
ddd. Bottom layer: F01 Amber Maple.
eee. Bottom layer: F18 Glass Plastique.
fff. Bottom layer: F19 Skylark Boomerang.
ggg. Bottom layer: F17 Charcoal Bloomberg.
hhh. Bottom layer: F16 Beluga Beige.
iii. Bottom layer: F20 Tangle Seaweed.
jjj. Bottom layer: F21 Tangle Wheat.
kkk. Bottom layer: F09 Ubatuba Granite.
lll. Bottom layer: F08 Labrador Granite.
mmm.
Bottom layer: F07 Jamocha Granite.
nnn. Bottom layer: W07 Mystique Night.
ooo. Bottom layer: F06 Colorado Slate.
ppp. Bottom layer: W06 Mystique Dusk.
qqq. Bottom layer: W04 Antique Topaz.
rrr. Bottom layer: W08 Sandy Topaz.
sss. Bottom layer: W05 Greystone.
ttt. Bottom layer: W03 Amber Fusion.
uuu. Bottom layer: F05 Carrara Envision.
vvv. Bottom layer: W11 Saffron Tigris.
www.
Bottom layer: W10 Natural Tigris.
xxx. Bottom layer: W09 Green Tigris.
yyy. Bottom layer: F14 Seagrass Strand.
zzz. Bottom layer: F15 Wheat Strand.
aaaa. Bottom layer: F10 Bamboo Cane.
bbbb. Bottom layer: F12 Cotton Paper.
cccc. Bottom layer: F13 Fallen Leaves.
dddd. Bottom layer: F11 Burnished Glaze.
eeee. Bottom layer: Solid Color #1:
10440-19
Bottom layer: Solid Color #2:
D.
2.5
Graphics:
1.
Type sizes: Selected from manufacturer's standard sizes indicated in
SCHEDULE for particular units; meet ADA requirements for letter proportions
and sizes.
2.
Typography: Reference signage schedule and drawings for details. Font(s)
selected from manufacturer’s standards unless otherwise specified. All text
and graphics shall be a true representation of the typeface(s) and/or graphics
specified. Letter spacing and interline spacing shall be set by the manufacturer.
a.
Helvetica Regular (HR)
b.
Futura (FUT)
c.
Optima (O)
d.
Frutiger (F55)
e.
Typeface(s) as indicated in SCHEDULES Article and Drawings.
3.
Type Code(s): Uppercase.
4.
Type Code(s): Initial caps.
5.
Type Code(s): Combination.
6.
Type Code(s): Indicated in SCHEDULES Article.
7.
Imprint Colors: Selected by Architect from manufacturer's standard 40 non
glare screening ink colors per unit and indicated in SCHEDULE; color contrast
background colors in accord with ADA requirements.
8.
Copy/Message List: Indicated in SCHEDULE.
9.
Reference drawings and Signage Schedule for details.
10. All text and graphics shall be a true representation of typeface(s) and/or
graphics specified.
FABRICATION
A.
Shop assembly:
1.
Fabricate units to configurations indicated on reviewed shop drawings.
2.
Provide copy on inserts, and covers required on reviewed shop drawings and in
accord with ADA requirements.
3.
Provide additional blank paper as specified.
4.
Include instruction sheets for removal and replacement inserts and installation.
PART 3 EXECUTION
3.1
3.2
EXAMINATION
A.
Do not begin installation until substrates have been properly prepared.
B.
If substrate preparation is the responsibility of another installer, notify Architect of
unsatisfactory preparation before proceeding.
PREPARATION
10440-20
3.3
3.4
A.
Clean surfaces thoroughly prior to installation.
B.
Prepare surfaces using the methods recommended by the manufacturer for achieving
the best result for the substrate under the project conditions.
INSTALLATION
A.
Install products in accordance with manufacturer’s instructions, in locations and with
mounting methods as specified in sign and location drawings.
B.
Square, plumb and level all installed products.
C.
Install all signage in accordance with the Americans with Disabilities Act
Accessibility Guidelines (ADAAG) and any applicable local regulations and/or
codes.
D.
Upon completion of the work, sign installer shall remove any unused products,
materials, packaging and debris from the installation site.
CLEANING
A.
3.5
3.6
Clean all exposed surface not more than 48 hours prior to Date of Substantial
Completion in accordance with manufacturer’s written cleaning instructions.
PROTECTION
A.
Protect installed products until completion of project.
B.
Touch-up, repair or replace damaged products before Substantial Completion.
SIGN SCHEDULES
A.
Refer to Signage Schedule and Drawings for sizes, locations, sign types, layouts,
typography specifications, sign text/copy and sign graphics.
END OF SECTION
10440-21