06 September 2011

advertisement
Australian Government
No. C 09 Tuesday 6 September 2011
Published by the National Industrial Chemicals
Notification and Assessment Scheme - NICNAS
Gazette
CHEMICAL
© Commonwealth of Australia 2011
ISBN 1035-9877
This work is copyright. Apart from any use as permitted under the Copyright Act 1968, no part may be reproduced by any
process without prior written permission from the Commonwealth available from the Attorney-General’s Department.
Requests and inquiries concerning reproduction and rights should be addressed to:
Commonwealth Copyright Administration
Copyright Law Branch
Attorney-General's Department
Robert Garran Offices
National Circuit
Canberra ACT 2600
email: Commonwealth.Copyright@ag.gov.au <mailto:Commonwealth.Copyright@ag.gov.au>
web: <http://www.ag.gov.au/cca>
The Industrial Chemicals (Notification and Assessment) Act 1989 (the Act) commenced on
17 July 1990. As required by Section 5 of the Act, a Chemical Gazette is published on the
first Tuesday in any month or on any days prescribed by the regulations.
CONTENTS
CONSULTATIONS
1
PUBLIC RELEASE OF DRAFT PRIORITY EXISTING CHEMICAL
REPORT FOR DIETHYL PHTHALATE
5
2
CALL FOR INFORMATION ON CHEMICALS OF SECURITY
CONCERN – A REMINDER
7
SPECIAL NOTICES
3
REMINDER OF NICNAS REGISTRATION RENEWAL 2011-12
8
4
ANNUAL REPORTING OBLIGATIONS
9
5
AMENDMENT OF NICNAS COSMETICS GUIDELINES
10
6
FUTURE MANAGEMENT OF CHEMICALS OF SECURITY
CONCERN
11
NEW CHEMICALS
SUMMARY REPORTS
7
LTD/1529
POLYISOCYANATE IN BAYHYDUR 401-70
12
8
LTD/1531
POLYMER IN SETAL 1606 BA-80
15
9
LTD/1537
POLYMER IN SYNOLAC PT30X
18
11
STD/1389
WESTON 705
21
12
STD/1394
UU
24
13
STD/1396
H-MI AMMONIUM SALT
26
14
PLC/996
VGP-27960
28
15
PLC/997
POLYMER 218
30
16
EX/163
CHEMICAL IN GYPTRON T-454 AND
GYPTRON KT-252
32
17
EX/164
POLYMER IN SAG TP-325
35
18
ACCESS TO FULL PUBLIC REPORTS
38
PERMITS ISSUED
19
COMMERCIAL EVALUATION CATEGORY PERMITS
39
20
EARLY INTRODUCTION PERMITS
40
21
LOW VOLUME CHEMICAL PERMITS
41
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES
22
NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES FIVE
YEARS AFTER ISSUING OF ASSESSMENT CERTIFICATES
42
23
NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING ON
THE AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES
AFTER ISSUING OF ASSESSMENT CERTIFICATES
45
5
1
PUBLIC RELEASE OF DRAFT PRIORITY EXISTING CHEMICAL REPORT
FOR DIETHYL PHTHALATE
In accordance with section 60E(1) of the Industrial Chemicals (Notification and Assessment) Act
1989 (the Act), as amended, notice is hereby given by the Director that the draft Priority Existing
Chemical (PEC) assessment report on Diethyl Phthalate (DEP) is now available for public
comment.
Under Section 60D of the Act, the draft PEC report was given to applicants for 28 days to enable
corrections of any errors. No requests for corrections were received. The report focuses on
assessment of risks for the public associated with potential exposure to DEP through the use of
children’s toys, child care articles and cosmetics.
A recommendation to reducing the risks identified for children and the general public from use of
DEP-containing cosmetics is made.
The draft report (hard or read-only electronic copy) can be obtained by contacting Ms Julie
Brown via phone (02) 8577 8870 or fax (02) 8577 8888 or e-mail to julie.brown@nicnas.gov.au
The draft report is also available on the NICNAS website at
http://www.nicnas.gov.au/consultations.asp.
Under Section 60E(2) of the Act, any requests to vary the draft report should be received in
writing to NICNAS by close of business (5:30 pm) on 4 October 2011. This is a statutory
deadline, which cannot be extended.
Submission format for variation requests
Any requests to vary the draft report must be made with respect to the draft report and be
accompanied by a completed application form (NICNAS Form 4a) which is available on the
NICNAS website at http://www.nicnas.gov.au/Forms/Existing_Chemicals/Form4a_PDF.pdf.
Applications should clearly outline any amendment or change(s) requested. All applications for
variation must identify the exact words, sentence or paragraph in the report to be varied and then
state replacement words, sentences or paragraphs. The rationale behind any request for variation
must be clearly explained, with references where relevant.
Requests for variation should be sent to: NICNAS, GPO Box 58, Sydney NSW 2001.
Briefings
Briefings on the findings and recommendations of the report will be held in Sydney and
Melbourne, between 21 and 23 September, depending on the level of interest. Please indicate
your interest in attending the briefing and preference of city in the attached sheet by
9 September 2011 via e-mail or fax to NICNAS.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
6
To:
Fax no:
e-mail:
By post:
Existing Chemicals Program
02 8577 8888
Trang.Pham@nicnas.gov.au
GPO Box 58 Sydney NSW 2001
CONFIRMATION OF ATTENDANCE AT THE NICNAS - DEP BRIEFINGS
Name:
Organisation:
Email address:
Phone: ______________________Fax:___________________
Attending the briefing:
Yes 
No
Please mark your preference below:
City:
Sydney 
Melbourne 
Date in September:
21 (Wednesday) 
Chemical Gazette
22 (Thursday) 
23 (Friday) 
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
7
2
CALL FOR INFORMATION ON CHEMICALS OF SECURITY CONCERN –
A REMINDER
The National Industrial Chemicals Notification and Assessment Scheme (NICNAS) published a
voluntary call for information on certain chemicals of potential security concern in the Chemical
Gazette of 2 August 2011.
NICNAS is collating information on these chemicals on behalf of the Commonwealth
Government Attorney-General’s Department (AGD). The information will primarily be used to
inform risk assessments on the chemicals.
This notice is a reminder that the closing date for the requested information is
13 September 2011.
The call for information can be accessed at: http://www.nicnas.gov.au/Consultations.asp
For further information, please contact Mr Phillip Sharp by phone: (02) 8577 8820, fax: (02)
8577 8888 or e-mail: phillip.sharp@nicnas.gov.au.
Please send the requested information to:
Ms Maureen Hardy
Science Strategy & International Programs
NICNAS
GPO Box 58
Sydney NSW 2001
e-mail: maureen.hardy@nicnas.gov.au
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
8
3
REMINDER OF NICNAS REGISTRATION RENEWAL 2011-12
All importers and manufacturers of relevant industrial chemicals for commercial purposes
must be registered with NICNAS prior to introducing these chemicals regardless of the
amount of industrial chemicals imported and / or manufactured.
The NICNAS registration year runs from 1 September to 31 August annually. The following
information relates to NICNAS registration renewals for 2011-12
RENEWAL DEADLINE
On 18 July 2011, NICNAS mailed Renewal Tax Invoices and an Application form for
renewal of registration/ non-renewal. The renewal deadline was 31 August 2011. If you have
not yet received an invoice, please contact NICNAS urgently on 1800 638 528.
Registration forms are available on the NICNAS website at:
www.nicnas.gov.au/Forms/Registration.asp
PENALTIES APPLY TO UNREGISTERED INTRODUCERS
The NICNAS registration for an introducer of relevant industrial chemicals lapsed if it was
not renewed by the 31 August 2011 deadline. Applications received after this date are
considered late renewal applications, and subject to a mandatory late renewal penalty. The
late renewal penalty is calculated at 15% of the total registration cost.
An introducer of industrial chemicals is not registered until ALL registration fees, including
late penalty fees (where applicable) have been paid.
It is an offence for a person to introduce (import and/or manufacture) relevant industrial
chemicals without a NICNAS registration in force. The legislation provides for severe
penalties for a person who introduces relevant industrial chemicals without a current
registration in place.
If you did not renew the NICNAS registration by 31 August 2011, you are advised not to
proceed with introducing relevant industrial chemicals until your NICNAS registration
obligations have been fulfilled as NICNAS has the ability to identify introducers who are in
breach of the legislation.

For further information, please contact NICNAS on:

Free call: 1800 638 528

Phone: (02) 8577 8800

Fax: (02) 8577 8888

E-mail: registration@nicnas.gov.au

or visit our website at www.nicnas.gov.au
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
9
4
ANNUAL REPORTING OBLIGATIONS
Under sections 21AA and 40N of the Industrial Chemicals (Notification and Assessment) Act
1989, a person introducing a new industrial chemical under certain permits, certificates or
exemptions in a registration year is required to provide a report to the Director, NICNAS,
stating the name and quantity of the chemical that was introduced.
When are Reports Due?
Reports are to be submitted online at the end of the NICNAS Registration period (31 August
2011). The reporting deadline is 28 September 2011.
Permits and Certificates
Organisations who have been issued one of the following New Chemical Permits/Certificates
will need to submit an annual report. Chemical details and allowable quantity have been prepopulated in the online Annual Reporting Module to facilitate reporting:
Commercial Evaluation Permit (CEC); and/or
Low Volume Chemical Permit (LVC); and/or
Controlled Use Permit (CUP); and/or
Self Assessed Assessment Certificate (SAPLC).
Exemptions
Some low regulatory concern chemicals are exempt from notification to NICNAS even if
they are new industrial chemicals. Most exemption categories have an Annual Reporting
obligation. If your organisation has introduced (imported or manufactured) a new industrial
chemical under one of the exemption categories below you will need to submit an annual
report:
≤ 100 kg Cosmetic Exemption; and/or
≤ 1% Cosmetic Exemption; and/or
≤ 100 kg Non-Cosmetic Exemption; and/or
≤ 100 kg Research & Development Exemption; and/or
Transhipment Exemption.
Online Reporting (Enrolment Required)
The NICNAS Annual Reporting Module (ARM) has been developed to enable organisations
with annual reporting obligations to submit reports online via the following NICNAS website
address:
https://secure.nicnas.gov.au/arm/WebForms/SignIn.aspx.
How Do I Enrol for Online Reporting?
Enrol online via NICNAS website link
https://secure.nicnas.gov.au/arm/WebForms/SignIn.aspx.
Select the ENROL Button under the NEW ENROLMENT Section on the Home page &
submit your organisation’s details. Once your enrolment application has been received at
NICNAS, access will be activated & your Login Password confirmed by e-mail.
Annual Reporting Module User Guide (PDF
Frequently Asked Questions
Chemical Gazette
1.9MB);
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
10
5
AMENDMENT OF NICNAS COSMETICS GUIDELINES
NICNAS has made two changes to the NICNAS Cosmetic Guidelines in consultation with
the NICNAS Cosmetic Advisory Group.
The first change involves modifying the existing Part F of the Cosmetics Guidelines on
Prohibited or Restricted Cosmetic Chemicals in Australia. The list of prohibited or restricted
chemicals has been replaced by links to sources of information on chemicals that by law,
must not be used in cosmetics in Australia, or may be used with restrictions.
The revised Part F also includes links to useful information on cosmetic ingredients that are
prohibited or restricted in countries other than Australia.
The second change involves the creation of a new part G on a List of Sunscreening Agents
for Use in Cosmetic Products. The new Part G sets out the recommended UV filters and their
concentrations for cosmetic sunscreen products used on the skin. These include:


moisturising products for dermal application (e.g. skin care creams/lotions) with SPF
up to 15, sunbathing products with sun protection for a secondary purpose with SPF
up to 15, and untinted lip products (e.g. lip balms) with SPF, which were previously
regulated as therapeutic goods but have been regulated as cosmetics since 2007, and
other cosmetic products containing sunscreens such as tinted lip products (e.g.
lipsticks) with SPF and tinted bases/foundations with SPF.
The new Part G aligns the regulatory controls on UV filters between the therapeutic and
industrial chemicals regulatory frameworks.
The updated Cosmetics Guidelines can be found on the NICNAS website at
http://www.nicnas.gov.au/Current_Issues/Cosmetics/Cosmetic_Guidelines_PDF.pdf.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
11
6
FUTURE MANAGEMENT OF CHEMICALS OF SECURITY CONCERN
The Attorney-General’s Department is inviting business to participate in a survey about
chemicals of concern, particularly those that are precursors to home-made explosives.
If your business imports, distributes, transports, manufactures, handles or uses these
chemicals then this is your chance to contribute to Australia’s safety and security by having
your say on how these chemicals are managed in the future.
This includes universities, farmers, hardware stores, pool chemical suppliers and hairdressers.
The chemicals of concern (in certain forms and concentration) are:

hydrogen peroxide

sodium chlorate

nitric acid

potassium chlorate

sodium perchlorate

potassium perchlorate

ammonium perchlorate

sodium nitrate

potassium nitrate

nitromethane

sodium azide.
The online survey (external website) is open between 1 and 21 September 2011.
More information
Find out more about government policy towards chemicals of security concern (external
website).
Contact
Online survey queries
Email: chemicalsecurity@au.pwc.com
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
12
7
PUBLICATION SUMMARY REPORT
Polyisocyanate in Bayhydur 401-70
Summary Report
Reference No: LTD/1529
Bayer MaterialScience Pty Ltd (ABN 18 086 237 765) of 17-19 Wangara Road, Cheltenham
VIC 3129 and PPG Industries Australia Pty Ltd (ABN 82 055 500 939) of McNaughton Road
Clayton VIC 3169 have submitted a limited notification statement in support of their
application for an assessment certificate for Polyisocyanate in Bayhydur 401-70. The notified
polymer is intended to be used as a component of hardener products for water based coatings.
Up to 100 tonnes of the notified polymer will be imported per annum for each of the first five
years.
Hazard Classification
Based on the information provided, the notified polymer is classified as hazardous according
to the Approved Criteria for Classifying Hazardous Substances [NOHSC:1008(2004)] with
the following risk phrase:

Xn; R42 May cause sensitisation by inhalation
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified polymer is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified polymer is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
Based on the reported use pattern, the notified polymer is not considered to pose an
unreasonable risk to the environment.
Recommendations
Regulatory Controls
Hazard Classification and Labelling

Safe Work Australia, should consider the following health hazard classification for
the notified polymer:

Conc. ≥ 1%: R42 may cause sensitisation by inhalation
Health Surveillance

As the notified polymer contains isocyanate functional groups, employers should
carry out health surveillance for any worker who has been identified in the workplace
risk assessment as having a history of isocyanate sensitivity, asthma or other
pulmonary condition and who may be adversely affected by isocyanate exposure.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
13
Control Measures
Occupational Health and Safety

Employers should implement the following isolation and engineering controls to
minimise occupational exposure to the notified polymer during reformulation and use
of products containing the notified polymer:

Ventilation systems including local exhaust ventilation when inhalation
exposure could occur, where possible.

Automated processes, where possible.

Ventilated spray booths during spray application, where possible.

Spray application to occur in well-ventilated areas when spray booths cannot be
used.

Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer during reformulation
and use of products containing the notified polymer:

Keep containers securely sealed and check regularly for spills and leaks.

Avoid inhalation of vapours, mists and aerosols.

Avoid contact with skin and eyes.

Wash hands after handling the notified polymer, or containers and equipment
containing it.

Spray application should be carried out in accordance with the Safe Work Australia
National Guidance Material for Spray Painting [NOHSC (1999)].

Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer during
reformulation and use of products containing the notified polymer:

Isocyanate-resistant gloves

Coveralls

Safety glasses

Appropriate respiratory protection for any process where inhalation exposure
may occur.

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

Atmospheric monitoring should be conducted to measure workplace concentrations of
isocyanates during reformulation and use of products containing the notified polymer.
Employers should ensure that the exposure standard for isocyanates [NOHSC:
1003(1995)] is not exceeded for all areas where the notified polymer will be handled.

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)] workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
14
Disposal

The notified polymer should be disposed of to landfill.
Emergency procedures

Spills or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the polymer under secondary notification provisions
based on changes in certain circumstances. Under Section 64 of the Industrial Chemicals
(Notification and Assessment) Act (1989) the notifier, as well as any other importer or
manufacturer of the notified polymer, have post-assessment regulatory obligations to notify
NICNAS when any of these circumstances change. These obligations apply even when the
notified polymer is listed on the Australian Inventory of Chemical Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(1) of the Act; if
 the polymer has a number-average molecular weight of less than 1000;
or
(2)
Under Section 64(2) of the Act; if
 the function or use of the polymer has changed from a component of hardener
products, or is likely to change significantly;
 the amount of polymer being introduced has increased from 100 tonnes per
annum, or is likely to increase, significantly;
 the polymer has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the polymer on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
Material Safety Data Sheet
The MSDS of a product containing the notified polymer provided by the notifier was
reviewed by NICNAS. The accuracy of the information on the MSDS remains the
responsibility of the applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
15
8
PUBLICATION SUMMARY REPORT
Polymer in Setal 1606 BA-80
Summary Report
Reference No: LTD/1531
Nuplex Industries (Aust) Pty Ltd (ABN: 25 000 045 572) of 49-61 Stephen Road, Botany,
NSW 2019 has submitted a limited notification statement in support of their application for
an assessment certificate for Polymer in Setal 1606 BA-80. The notified chemical is intended
to be used as a component of paint products. Up to 15 tonnes of the notified polymer will be
imported per annum for each of the first five years.
Hazard Classification
As no toxicity data were provided for the notified polymer, it cannot be classified according
to the Approved Criteria for Classifying Hazardous Substances [NOHSC:1008(2004)].
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified polymer is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified polymer is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
On the basis of the assessed use pattern, the notified polymer is not considered to pose an
unreasonable risk to the environment.
Recommendations
Control Measures
Occupational Health and Safety

Employers should implement the following engineering controls to minimise
occupational exposure to the notified polymer:

Spray booths (or other ventilation) during application

Given the appreciable proportion of low molecular weight species, employers should
ensure that the following personal protective equipment is used by workers to
minimise occupational exposure to the notified polymer:

Gloves, goggles, overalls

Respiratory protection during spray applications

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

Spray applications should be carried out in accordance with the Safe Work Australia
National Guidance Material for Spray Painting [NOHSC (1999)] or relevant State
and Territory Codes of Practice.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
16

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the Approved Criteria for Classifying Hazardous
substances [NOHSC:1008(2004)] workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified polymer should be disposed of to landfill.
Emergency procedures

Spills or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the chemical under secondary notification
provisions based on changes in certain circumstances. Under Section 64 of the Industrial
Chemicals (Notification and Assessment) Act (1989) the notifier, as well as any other
importer or manufacturer of the notified chemical, have post-assessment regulatory
obligations to notify NICNAS when any of these circumstances change. These obligations
apply even when the notified chemical is listed on the Australian Inventory of Chemical
Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(1) of the Act; if
 the polymer has a number-average molecular weight of less than 1000;
or
(2)
Under Section 64(2) of the Act; if
 the function or use of the polymer has changed from a component of paint
products, or is likely to change significantly;
 the amount of polymer being introduced has increased from 15 tonnes per annum,
or is likely to increase, significantly;
 the polymer has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the polymer on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
17
Material Safety Data Sheet
The MSDS of a product containing the notified polymer provided by the notifier was
reviewed by NICNAS. The accuracy of the information on the MSDS remains the
responsibility of the applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
18
9
PUBLICATION SUMMARY REPORT
Polymer in Synolac PT30X
Summary Report
Reference No: LTD/1537
International Sales & Marketing Pty Ltd (ABN 36 467 259 314) of 262 Highett Rd, Highett
VIC 3190 has submitted a limited notification statement in support of their application for an
assessment certificate for Polymer in Synolac PT30X. The notified polymer is intended to be
used as a component of enamel paints. Up to 1000 tonnes of the notified polymer will be
imported per annum for each of the first five years.
Hazard Classification
As no toxicity data were provided, the notified polymer cannot be classified according to the
Approved Criteria for Classifying Hazardous Substances (NOHSC, 2004).
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified polymer is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified polymer is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
On the basis of the assessed use pattern, the notified polymer is not considered to pose an
unreasonable risk to the environment.
Recommendations
Control Measures
Occupational Health and Safety

Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer:

Avoid contact with skin and eyes

Do not inhale vapours/mists

Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer:

Overalls

Gloves

Goggles

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
19

Spray applications should be carried out in accordance with the Safe Work Australia
National Guidance Material for Spray Painting [NOHSC (1999)] or relevant State
and Territory Codes of Practice.

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)] workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified polymer should be disposed of to landfill.
Emergency procedures

Spills or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the chemical under secondary notification
provisions based on changes in certain circumstances. Under Section 64 of the Industrial
Chemicals (Notification and Assessment) Act (1989) the notifier, as well as any other
importer or manufacturer of the notified chemical, have post-assessment regulatory
obligations to notify NICNAS when any of these circumstances change. These obligations
apply even when the notified chemical is listed on the Australian Inventory of Chemical
Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(1) of the Act; if
 the polymer has a number-average molecular weight of less than 1000;
or
(2)
Under Section 64(2) of the Act; if
 the function or use of the polymer has changed from a component of surface
coatings, or is likely to change significantly;
 the amount of polymer being introduced has increased from 1000 tonnes per
annum, or is likely to increase, significantly;
 the polymer has begun to be manufactured in Australia;
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
20
 additional information has become available to the person as to an adverse effect
of the polymer on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
Material Safety Data Sheet
The MSDS of a product containing the notified polymer provided by the notifier was
reviewed by NICNAS. The accuracy of the information on the MSDS remains the
responsibility of the applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
21
10
PUBLICATION SUMMARY REPORT
Weston 705
Summary Report
Reference No: STD/1389
Chemtura Australia Pty Ltd (ABN 18 005 225 507) of Level 7, 435 King William Street,
Adelaide SA 5000 has submitted a standard notification statement in support of their
application for an assessment certificate for Weston 705. The notified chemical is intended
to be used as an additive up to 0.5% in the production of rubber and plastics. Up to 10 tonnes
of the notified chemical will be imported per annum for each of the first five years.
Hazard Classification
Based on the data provided the notified chemical is not classified as hazardous according to
the Approved Criteria for Classifying Hazardous Substances [NOHSC:1008(2004)].
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified chemical is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified chemical is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
On the basis of the assessed use pattern, the notified chemical is not considered to pose an
unreasonable risk to the environment.
Recommendations
Control Measures
Occupational Health and Safety

Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as introduced for
formulation:

Avoid contact with skin and eyes

Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced for
formulation:

Impervious gloves

Safety glasses

Impervious clothing

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

A copy of the MSDS should be easily accessible to employees.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
22

If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)] workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified chemical should be disposed of to landfill.
Emergency procedures

Spills or accidental release of the notified chemical should be handled by physical
containment, collection and subsequent safe disposal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the chemical under secondary notification
provisions based on changes in certain circumstances. Under Section 64 of the Industrial
Chemicals (Notification and Assessment) Act (1989) the notifier, as well as any other
importer or manufacturer of the notified chemical, have post-assessment regulatory
obligations to notify NICNAS when any of these circumstances change. These obligations
apply even when the notified chemical is listed on the Australian Inventory of Chemical
Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(2) of the Act; if
 the function or use of the chemical has changed from a plastic and rubber additive
at up to 0.5% or is likely to change significantly;
 the amount of chemical being introduced has increased from 10 tonnes per annum,
or is likely to increase, significantly;
 the chemical has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the chemical on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
23
Material Safety Data Sheet
The MSDS of the notified chemical provided by the notifier was reviewed by NICNAS. The
accuracy of the information on the MSDS remains the responsibility of the applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
24
11
PUBLICATION SUMMARY REPORT
UU
Summary Report
Reference No: STD/1394
Mark Sensing Australia Pty. Ltd. (ABN 27 005 481 961) of 31 Jersey Road Bayswater VIC
3153 has submitted a standard notification statement in support of their application for an
assessment certificate for UU. The notified chemical is intended to be used as colour
developer for thermal paper. Up to 10 tonnes of the notified chemical will be imported per
annum for each of the first five years.
Hazard Classification
Based on the submitted data, the notified chemical is not classified as hazardous according to
the Approved Criteria for Classifying Hazardous Substances [NOHSC:1008(2004)].
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified chemical is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified chemical is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
On the basis of the PEC/PNEC ratio and the assessed use pattern, the notified chemical is not
considered to pose an unreasonable risk to the environment.
Recommendations
Control Measures
Occupational Health and Safety

Employers should implement the following engineering controls to minimise
occupational exposure to aerosols (particles) of the notified chemical during
reformulation:

Local Exhaust Ventilation

Enclosed and automated systems

Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to aerosols (particles) of the notified
chemical during reformulation:

Respiratory protection

Service personnel should wear cotton or disposable gloves and ensure adequate
ventilation is present during cleaning processes involving the notified chemical and
during routine maintenance and repairs.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
25

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)] workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified chemical should be disposed of to landfill.
Emergency procedures

Spills or accidental release of the notified chemical should be handled by physical
containment, collection and subsequent safe removal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the chemical under secondary notification
provisions based on changes in certain circumstances. Under Section 64 of the Industrial
Chemicals (Notification and Assessment) Act (1989) the notifier, as well as any other
importer or manufacturer of the notified chemical, have post-assessment regulatory
obligations to notify NICNAS when any of these circumstances change. These obligations
apply even when the notified chemical is listed on the Australian Inventory of Chemical
Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(2) of the Act; if
 the function or use of the chemical has changed from as a colour developer for
thermal paper, or is likely to change significantly;
 the amount of chemical being introduced has increased from up to 10
tonnes/annum, or is likely to increase, significantly;
 the chemical has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the chemical on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
26
12
PUBLICATION SUMMARY REPORT
H-MI Ammonium Salt
Summary Report
Reference No: STD/1396
Hewlett Packard Australia Pty Ltd (ABN: 74 004 394 763) of 33 Burwood Highway Forest
Hill VIC 3131 has submitted a standard notification statement in support of their application
for an assessment certificate for H-MI Ammonium Salt. The notified chemical is intended to
be used as a dye component for inkjet printer inks. Up to one tonne of the notified chemical
will be imported per annum for each of the first five years.
Hazard Classification
Based on the submitted data, the notified chemical is not classified as hazardous according to
the Approved Criteria for Classifying Hazardous Substances (NOHSC, 2004).
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified chemical is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified chemical is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
On the basis of the PEC/PNEC ratio and the assessed use pattern, the notified chemical is not
considered to pose an unreasonable risk to the environment.
Recommendations
Control Measures
Occupational Health and Safety

Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as introduced:

Avoid contact with eyes;

Printers should be located in well-ventilated areas.

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

Service personnel should wear cotton or disposable gloves and ensure adequate
ventilation is present when removing spent inkjet printer inks cartridges containing
the notified chemical and during routine maintenance and repairs.

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified chemical/polymer are classified as
hazardous to health in accordance with the Approved Criteria for Classifying
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
27
Hazardous Substances [NOHSC:1008(2004)] workplace practices and control
procedures consistent with provisions of State and Territory hazardous substances
legislation must be in operation.
Disposal

The notified chemical should be disposed of to landfill.
Emergency procedures

Spills or accidental release of the notified chemical should be handled by physical
containment, collection and subsequent safe disposal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the chemical under secondary notification
provisions based on changes in certain circumstances. Under Section 64 of the Industrial
Chemicals (Notification and Assessment) Act (1989) the notifier, as well as any other
importer or manufacturer of the notified chemical, have post-assessment regulatory
obligations to notify NICNAS when any of these circumstances change. These obligations
apply even when the notified chemical is listed on the Australian Inventory of Chemical
Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(2) of the Act; if
 the function or use of the chemical has changed from a dye component for inkjet
printer inks contained within sealed cartridges, or is likely to change significantly;
 the amount of chemical being introduced has increased from one tonne/annum, or
is likely to increase, significantly;
 the chemical has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the chemical on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
No additional secondary notification conditions are stipulated.
Material Safety Data Sheet
The MSDS of the product containing the notified chemical provided by the notifier was
reviewed by NICNAS. The accuracy of the information on the MSDS remains the
responsibility of the applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
28
13
PUBLICATION SUMMARY REPORT
VGP-27960
Summary Report
Reference No: PLC/996
Dupont (Australia) Ltd (ABN 59000716469) of 7 Eden Park Drive, Macquarie Park NSW
2113 has submitted a polymer of low concern (PLC) notification statement in support of their
application for an assessment certificate for VGP-27960. The notified polymer is intended to
be used as a component of refinish automotive paints. Up to 70 tonnes of the notified
polymer will be imported per annum for each of the first five years.
Hazard Classification
No toxicological data were submitted. The notified polymer meets the PLC criteria and can
therefore be assumed to be of low hazard.
Human Health Risk Assessment
Based on the assumed low hazard and the assessed use pattern, the notified polymer is not
considered to pose an unreasonable risk to the health of workers and the public.
Environmental Risk Assessment
Based on the assumed low hazard and the assessed use pattern, the notified polymer is not
considered to pose an unreasonable risk to the environment.
Health and Safety Recommendations

No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself. However, these should be
selected on the basis of all ingredients in the formulation.

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

A copy of the MSDS should be easily accessible to employees.

Spray application should be carried out in accordance with the Safe Work Australia
National Guidance Material for Spray Painting [NOHSC (1999)].

If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)], workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified polymer should be disposed of to landfill.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
29
Emergency Procedures

Prevent from entering into soil, ditches, sewers, waterways and/or groundwater.

Spills and/or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the polymer under secondary notification provisions
based on changes in certain circumstances. Under Section 64 of the Industrial Chemicals
(Notification and Assessment) Act (1989) the notifier, as well as any other importer or
manufacturer of the notified polymer, have post-assessment regulatory obligations to notify
NICNAS when any of these circumstances change. These obligations apply even when the
notified polymer is listed on the Australian Inventory of Chemical Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(1) of the Act; if
 the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
(2)
Under Section 64(2) of the Act; if
 the function or use of the notified polymer has changed from a component of
automotive paint, or is likely to change significantly;
 the amount of notified polymer being introduced has increased, or is likely to
increase, significantly;
 the notified polymer has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the chemical on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
Material Safety Data Sheet
The MSDS of the components of the notified polymer were provided by the applicant. The
accuracy of the information on the MSDS remains the responsibility of the applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
30
14
PUBLICATION SUMMARY REPORT
Polymer 218
Summary Report
Reference No: PLC/997
Ezi Floor Products (Vic) Pty Ltd (ABN 22 087 581 520) of Wareca, Unit 9, 1866 Princes
Highway, Clayton VIC 3168 and Bonakemi Australia Pty Ltd (ABN 35 096 221 448) of c/o
Nexia Court & Co, Level 29, 264-278 George Street, Sydney NSW 2000 have submitted a
polymer of low concern (PLC) notification statement in support of their application for an
assessment certificate for Polymer 218. The notified polymer is intended to be used as a
component in waterborne coating products, primarily floor finishes. Up to 5.5 tonnes of the
notified polymer will be imported per annum for each of the first five years.
Hazard Classification
No toxicological data were submitted. The notified polymer meets the PLC criteria and can
therefore be assumed to be of low hazard.
Human Health Risk Assessment
Based on the assumed low hazard and the assessed use pattern, the notified polymer is not
considered to pose an unreasonable risk to the health of workers and the public.
Environmental Risk Assessment
Based on the assumed low hazard and the assessed use pattern, the notified polymer is not
considered to pose an unreasonable risk to the environment.
Health and Safety Recommendations

No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself. However, these should be
selected on the basis of all ingredients in the formulation.

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)], workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified polymer should be disposed to landfill.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
31
Emergency Procedures

Prevent from entering into soil, ditches, sewers, waterways and/or groundwater.

Spills and/or accidental release of the product containing the notified polymer should
be handled by physical containment, collection and subsequent safe disposal.
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the polymer under secondary notification provisions
based on changes in certain circumstances. Under Section 64 of the Industrial Chemicals
(Notification and Assessment) Act (1989) the notifier, as well as any other importer or
manufacturer of the notified polymer, have post-assessment regulatory obligations to notify
NICNAS when any of these circumstances change. These obligations apply even when the
notified polymer is listed on the Australian Inventory of Chemical Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(1) of the Act; if
 the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
(2)
Under Section 64(2) of the Act; if
 the function or use of the notified polymer has changed from component of
waterborne coating, or is likely to change significantly;
 the amount of notified polymer being introduced has increased, or is likely to
increase, significantly;
 the notified polymer has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the chemical on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
Material Safety Data Sheet
The MSDS of product containing the notified polymer was provided by the applicant. The
accuracy of the information on the MSDS remains the responsibility of the applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
32
15
PUBLICATION SUMMARY REPORT
Chemical in Gyptron T-454 and Gyptron KT-252
Summary Report
Reference No: EX/163
Champion Technologies Pty Ltd (ABN: 22 008 079 614) of Suite 1, 5 Brodie-Hall Drive,
Technology Park, Bentley, WA 6102 has submitted a standard notification statement in
support of their application for an assessment certificate for Chemical in Gyptron T-454 and
Gyptron KT-252. The notified chemical is intended to be used as scale inhibitor used in oil
and gas production. Up to 15 tonnes of the notified chemical will be imported per annum for
each of the first five years.
Since the assessment certificate has been granted for the above notified chemical, Brenntag
Pty Ltd (ABN: 24 050 029 000) of Bldg 25, 270 Ferntree Gully Road, NOTTING HILL, VIC
3168 has submitted an application for extension of the assessment certificate, together with a
written agreement of the holder of the original certificate (Champion Technologies Pty Ltd)
for importing up to 17 tonnes of the notified chemical per annum for use as scale inhibitor
used in oil and gas production.
Hazard Classification
Based on the available data on the analogue chemical, the notified chemical is not classified
as hazardous according to the Approved Criteria for Classifying Hazardous Substances
(NOHSC, 2004).
Eye irritation scores are not available for the studies conducted with the analogue chemical.
Therefore the notified chemical can not be classified as an eye irritant using the Approved
Criteria.
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified chemical is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified chemical is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
On the basis of the PEC/PNEC ratio and the reported use pattern and the total import volume,
the notified chemical is not expected to pose a risk to the environment.
Recommendations
Control Measures
Occupational Health and Safety

Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical:
 Avoid skin and eye contact
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
33


Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical:
 Safety goggles or face shield, gloves and protective clothing
Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)] workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified chemical should be disposed of to landfill.
Emergency procedures

Spills or accidental release of the notified chemical should be handled by physical
containment, collection and subsequent safe disposal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the chemical under secondary notification
provisions based on changes in certain circumstances. Under Section 64 of the Industrial
Chemicals (Notification and Assessment) Act (1989) the notifier, as well as any other
importer or manufacturer of the notified chemical, have post-assessment regulatory
obligations to notify NICNAS when any of these circumstances change. These obligations
apply even when the notified chemical is listed on the Australian Inventory of Chemical
Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(2) of the Act; if
 the function or use of the chemical has changed from a scale inhibitor used at <
12% in oil and gas production, or is likely to change significantly;
 the amount of chemical being introduced has increased from 17 tonnes per annum,
or is likely to increase, significantly;
 the chemical has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the chemical on occupational health and safety, public health, or the
environment.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
34
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
No additional secondary notification conditions are stipulated.
Material Safety Data Sheet
The MSDS of a product containing the notified chemical provided by the notifier was
reviewed by NICNAS. The accuracy of the information on the MSDS remains the
responsibility of the applicant.
Extension Application
The extension applicant has provided an MSDS for a product containing the notified
chemical. The accuracy of the information on the MSDS remains the responsibility of the
extension applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
35
16
PUBLICATION SUMMARY REPORT
Polymer in SAG TP-325
Summary Report
Reference No: EX/164
Momentive Performance Materials Australia Pty Ltd (ABN 47 105 651 063) of Level 2 600
Victoria Street Richmond VIC 3121 and A.S. Harrison & Co Pty Ltd (89 000 030 437) of 75
Old Pittwater Road Brookvale NSW 2100 have submitted a polymer of low concern (PLC)
notification statement in support of their application for an assessment certificate for Polymer
in SAG TP-325. The notified polymer is intended to be used as a component of a diesel fuel
additive package. Up to 10 tonnes of the notified polymer will be imported per annum for
each of the first five years.
Since the assessment certificate has been granted for the above notified polymer, Connell
Bros Company Australasia Pty Ltd (ABN: 53 079 159 327) of 3/32 Windorah Street,
Stafford, QLD 4053 has submitted an application for extension of the assessment certificate,
together with a written agreement of the holders of the original certificate (Momentive
Performance Materials Australia Pty Ltd and A.S. Harrison & Co Pty Ltd) for importing up
to 10 tonnes of the notified polymer per annum for use as a component of a diesel fuel
additive package.
Hazard Classification
No toxicological data were submitted. The notified polymer meets the PLC criteria and can
therefore be considered to be of low hazard.
Human Health Risk Assessment
Under the conditions of the occupational settings described, the notified polymer is not
considered to pose an unreasonable risk to the health of workers.
When used in the proposed manner, the notified polymer is not considered to pose an
unreasonable risk to public health.
Environmental Risk Assessment
Based on the reported use pattern, the notified polymer is not considered to pose a risk to the
environment.
Recommendations
Control Measures
Occupational Health and Safety

Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer when introduced in
products at high concentrations (> 50%):
 Avoid skin and eye contact
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
36

Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer when introduced
in products at higher concentrations (> 50%):
 Safety goggles
 Coveralls
 Impervious gloves

Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.

A copy of the MSDS should be easily accessible to employees.

If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the Approved Criteria for Classifying Hazardous
Substances [NOHSC:1008(2004)], workplace practices and control procedures
consistent with provisions of State and Territory hazardous substances legislation
must be in operation.
Disposal

The notified polymer should be disposed of to landfill.
Emergency procedures

Spills and/or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Regulatory Obligations
Secondary Notification
This risk assessment is based on the information available at the time of notification. The
Director may call for the reassessment of the polymer under secondary notification provisions
based on changes in certain circumstances. Under Section 64 of the Industrial Chemicals
(Notification and Assessment) Act (1989) the notifier, as well as any other importer or
manufacturer of the notified polymer, have post-assessment regulatory obligations to notify
NICNAS when any of these circumstances change. These obligations apply even when the
notified polymer is listed on the Australian Inventory of Chemical Substances (AICS).
Therefore, the Director of NICNAS must be notified in writing within 28 days by the notifier,
other importer or manufacturer:
(1)
Under Section 64(1) of the Act; if
 the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
(2)
Under Section 64(2) of the Act; if
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
37
 the function or use of the notified polymer has changed from a component of a
lubricant or a diesel fuel additive package, or is likely to change significantly;
 the amount of notified polymer being introduced has increased, or is likely to
increase, significantly;
 the notified polymer has begun to be manufactured in Australia;
 additional information has become available to the person as to an adverse effect
of the chemical on occupational health and safety, public health, or the
environment.
The Director will then decide whether a reassessment (i.e. a secondary notification and
assessment) is required.
Material Safety Data Sheet
The MSDS of the imported products containing the notified polymer provided by the notifier
were reviewed by NICNAS. The accuracy of the information on the MSDS remains the
responsibility of the applicant.
Extension Application:
The extension applicant has provided an MSDS for a product containing the notified
polymer. The accuracy of the information on the MSDS remains the responsibility of the
extension applicant.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
38
17
ACCESS TO FULL PUBLIC REPORT
NICNAS publishes a Full Public Report for each new chemical assessed. These reports
are available for inspection at our NICNAS office by appointment only at Level 7, 260
Elizabeth St, SURRY HILLS NSW 2010.
Reports can also be viewed and downloaded free of charge from our website at
http://www.nicnas.gov.au/. Copies of these reports may also be requested, free of charge,
by contacting the Administration Section of NICNAS by phone: (02) 8577 8800 or fax:
(02) 8577 8888.
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
39
18
COMMERCIAL EVALUATION CATEGORY PERMIT
The permits listed in Table 1 were issued to import or manufacture the following chemicals
for commercial evaluation under section 21G of the Industrial Chemicals (Notification and
Assessment) Act 1989.
Table 1
Commercial Evaluation Category Permits
PERMIT
COMPANY
COMPANY
CHEMICAL OR
HAZARDOUS
NUMBER
NAME
POSTCODE
TRADE NAME
SUBSTANCE
784
SCHLUMBER
GER
AUSTRALIA
PTY LTD
6000
Poly(oxy-1,2ethanediyl),
alpha-sulfoomega-hydroxy, C11-14isoalkyl ethers,
C13-rich,
sodium salts
Yes
QUANTITY
USE
PERIOD
APPROVED
168 kg
Stabilizer
for a
cement
additive
2 yrs
N.D.: not determined; insufficient data available to effect a health effects classification under Approved Criteria
[NOHSC:1008(2004)]
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
40
19
EARLY INTRODUCTION PERMITS FOR NON-HAZARDOUS INDUSTRIAL
CHEMICALS
The permits listed in Table 2 were issued to import or manufacture the following chemicals
prior to the issue of their respective assessment certificates under section 30A of the Act.
Table 2
Early Introduction Permits
PERMIT
NUMBER
COMPANY
NAME
CHEMICAL OR
TRADE NAME
USE
760
International
Sales &
Marketing Pty
Ltd
Tego Flow 425
Component of printing ink &
coating for metal primer
761
Nuplex
Industries
(Aust) Pty Ltd
Polymer in Polyplex
8383
Ingredient for polymer composite
in fabrication of ducts, membrane
systems and road surfacing
762
DuPont
(Australia)
Ltd
Perfluorinated Polymer
in Capstone FS-81
Dirt and soil repellent in paints and
carpet products
764
Ricoh
Australia Pty
Ltd
Polymer in SD2-K Ink
Component of commercial printing
ink
765
Fujifilm
Australia Pty
Ltd
Polymer in UVIVID
FLEXO JD Ink Series
Component of ink for flexographic
printers
766
Reschem
Technologies
Pty Ltd
Polymer in NeoCryl
XK-62
Component of coatings
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
41
20
LOW VOLUME CATEGORY PERMITS
The permits listed in Table 3 were issued to import or manufacture the following chemicals
under section 21U of the Industrial Chemicals (Notification and Assessment) Act 1989. Low
Volume Category Permits are approved for 36 months.
Table 3
Low Volume Category Permits
PERMIT
NUMBER
COMPANY
NAME
COMPANY
POSTCODE
CHEMICAL OR TRADE
NAME
HAZARDOUS
SUBSTANCE
USE
935
(Renewal)
International
Flavors and
Fragrances
(Australia) Pty Ltd
3175
IDM Ketal
No
Component of
fragrance oil
936
Symrise Pty Ltd
2099
Benzoic acid, 2-[[3-(4hydroxyphenyl)-1oxopropyl]amino]-
No
Component of
hair and skin
care products
937
Canon Australia Pty
Ltd
2113
CIM-26
ND
Component of
inkjet printer
ink
N.D.: not determined; insufficient data available to effect a health effects classification under Approved Criteria
[NOHSC:1008(2004)]
Chemical Gazette
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
42
21
NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE AUSTRALIAN
INVENTORY OF CHEMICAL SUBSTANCES FIVE YEARS AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 14(1) of the Industrial Chemicals (Notification
and Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 4
Chemicals Eligible for Listing on the Australian Inventory of Chemical Substances
CHEMICAL NAME
Hexanedioic acid, polymer with 3hydroxy-2-(hydroxymethyl)-2methylpropanoic acid and 1,3isobenzofurandione, benzoate
1,3-Isobenzofurandione, polymer with
2,2-dimethyl-1,3-propanediol, 2,5furandione and 1,2-propanediol,
benzoate
Hexanedioic acid, polymer with 1,4cyclohexanedimethanol, 2-ethyl-2(hydroxyethyl)- 1,3-propanediol, and
hexahydro-1,3-isobenzofurandione,
3,5,5-trimethylhexanoate
1,3-Benzenedicarboxylic acid, 5sulfo-, 1,3-bis[2-(2hydroxyethoxy)ethyl] ester, sodium
salt (1:1), polymer with 1,3benzenedicarboxylic acid, 1,4cyclohexanedimethanol and 2,2'oxybis[ethanol]
1,3-Benzenedicarboxylic acid, 5sulfo-, 1,3-bis[2-(2hydroxyethoxy)ethyl] ester, sodium
salt (1:1), polymer with 1,3benzenedicarboxylic acid and 2,2'oxybis[ethanol]
2-Propenoic acid, 2-methyl-, methyl
ester, polymer with butyl 2propenoate, 1,4cyclohexanedimethanol, 1,3diisocyanato-2-methylbenzene, 2,4diisocyanato-1-methylbenzene,
ethenylbenzene, hydrazine, .alpha.hydro-.omega.-hydroxypoly(oxy-1,4butanediyl), 3-hydroxy-2(hydroxymethyl)-2-methylpropanoic
acid, 1-isocyanato-2-[(4Chemical Gazette
MOLECULAR FORMULA
CAS
NUMBER
(C8H4O3.C6H10O4.C5H10O4)x.xC7H6
O2
1312793-17-1
(C8H4O3.C5H12O2.C4H2O3.C3H8O2)x
.xC7H6O2
1312793-19-3
C9H18O2.x(C8H16O2.C8H10O3.C6H14
O3.C6H10O4)x
193293-23-1
(C16H22O11S.C8H16O2.C8H6O4.C4H1
0O3.Na)x
138533-16-1
(C16H22O11S.C8H6O4.C4H10O3.Na)x
904302-13-2
(C15H10N2O2.C15H10N2O2.C9H6N2O
2.C9H6N2O2.C8H16O2.C8H8.C7H12O2
.C5H10O4.C5H8O2.(C4H8O)nH2O.H4
N2)x.xC6H15N
1313803-47-2
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
43
isocyanatophenyl)methyl]benzene and
1,1'-methylenebis[4isocyanatobenzene], compd. with
N,N-diethylethanamine
2-Propenoic acid, 2-methyl-, polymer
with butyl 2-methyl-2-propenoate,
butyl 2-propenoate, N-(1,1-dimethyl3-oxobutyl)-2-propenamide and
methyl 2-methyl-2-propenoate,
ammonium salt
1,2,3,4-Butanetetracarboxylic acid
Fatty acids, tall-oil, 2-mercaptoethyl
esters, reaction products with
dichlorodimethylstannane, 2mercaptoethyl oleate, sodium sulfide
(Na2S) and trichloromethylstannane
Hexanedioic acid, polymer with 2aminoethanol, N-(2-aminoethyl)-1,2ethanediamine and
(chloromethyl)oxirane
1,3-Benzenedicarboxylic acid,
polymer with 2-butyl-2-ethyl-1,3propanediol, 2,2-dimethyl-1,3propanediol, 2-ethyl-2(hydroxymethyl)-1,3-propanediol,
1,6-hexanediol and
.alpha.,.alpha.’,.alpha."-1,2,3propanetriyltris[.omega.hydroxypoly[oxy(methyl-1,2ethanediyl)]], compd. with 2(dimethylamino)ethanol
Starch, ether with N-(2-carboxyethyl)N-(2-hydroxyethyl)-.beta.-alanine,
sodium salt
Formaldehyde, telomer with 1,3benzenedimethanamine, 1,3benzenediol and ethenylbenzene
Propanoic acid, 2[[(dodecylthio)thioxomethyl]thio]2-Propenoic acid, 2-methyl-, polymer
with butyl 2-propenoate,
ethenylbenzene and 2-propenoic acid,
potassium salt, tert-Bu
benzenecarboperoxoate-initiated
2-Propenoic acid, 2-methyl-, polymer
with butyl 2-propenoate,
ethenylbenzene and 2-propenoic acid
Beeswax, reaction products with 3-(2hydroxyethoxy)propyl groupterminated di-Me siloxanes
Chemical Gazette
(C9H15NO2.C8H14O2.C7H12O2.C5H8
O2.C4H6O2)x.xH3N
298793-17-6
C8H10O8
1703-58-8
Unspecified
201687-58-3
(C6H10O4.C4H13N3.C3H5ClO.C2H7N
O)x
264879-27-8
(C9H20O2.C8H6O4.C6H14O3.C6H14O2
.C5H12O2.(C3H6O)n(C3H6O)n(C3H6
506414-09-1
O)nC3H8O3)x.xC4H11NO
C8H15NO5.xNa.xUnspecified
905822-76-6
(C8H12N2.C6H6O2.CH2O)x.C8H8
710292-85-6
C16H30O2S3
558484-21-2
Unspecified
852920-53-7
(C8H8.C7H12O2.C4H6O2.C3H4O2)x
25120-19-8
Unspecified
467448-42-6
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
44
2-Propenoic acid, 2-methyl-, methyl
ester, polymer with .alpha.-(2-methyl1-oxo-2-propen-1-yl)-.omega.hydroxypoly(oxy-1,2-ethanediyl)
Chemical Gazette
(C5H8O2.(C2H4O)nC4H6O2)x
72892-39-8
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
45
23
NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 13B of the Industrial Chemicals (Notification and
Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 5
Chemicals Eligible for Immediate Listing on the Australian Inventory of Chemical
Substances
CHEMICAL NAME
Neodecanoic acid, 2-oxiranylmethyl ester,
polymer with 2,2-dimethyl-1,3propanediol, 2-ethyl-2-(hydroxymethyl)1,3-propanediol, hexahydro-1,3isobenzofurandione and 2-oxepanone
1H-Pyrrole-2,5-dione, 1,1'-(4-methyl-1,3phenylene)bisEthanol, 2-(2,4-diaminophenoxy)-, sulfate
(1:1)
1,4-Benzenedicarboxylic acid, polymer
with 1,4-butanediol, (2E)-2-butenedioic
acid, decanedioic acid, ethenylbenzene, 2ethylhexyl 2-propenoate, hexanedioic acid,
1,6-hexanediol and 2-propenoic acid, tertBu peroxide-initiated
Chemical Gazette
MOLECULAR FORMULA
CAS
NUMBER
(C13H24O3.C8H10O3.C6H14O3.C6
H10O2.C5H12O2)x
1262847-84-6
C15H10N2O4
6422-83-9
C8H12N2O2.H2O4S
70643-20-8
Unspecified
1207435-29-7
Commonwealth of Australia Gazette
No. C 09, 06 September 2011
Download