OUTLINE SPECIFICATIONS
FOR
NEW JOHN KERR ELEMENTARY SCHOOL
&
FREDERICK DOUGLASS ELEMENTARY
SCHOOL EXPANSION
WINCHESTER PUBLIC SCHOOLS
WINCHESTER, VIRGINIA
1355 Beverly Road │ Suite 105 │McLean VA 22101 │ ph 703 903 9100 │ fx 703 903
9755 www.grimmandparker.com
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
TABLE OF CONTENTS
DIVISION 01 - GENERAL REQUIREMENTS
01 10 00
SUMMARY
DIVISION 03 - CONCRETE
03 30 00
CAST-IN-PLACE CONCRETE
DIVISION 04 - MASONRY
04 20 00
04 72 00
UNIT MASONRY ASSEMBLIES
CAST STONE MASONRY
DIVISION 05 - METALS
05
05
05
05
05
05
05
12
21
31
40
50
51
52
00
00
00
00
00
00
13
STRUCTURAL STEEL FRAMING
STEEL JOISTS
STEEL DECKING
COLD-FORMED METAL FRAMING
METAL FABRICATIONS
METAL STAIRS
PIPE AND TUBE RAILINGS
DIVISION 06 - WOOD, PLASTICS, AND COMPOSITES
06 10 00
06 20 00
06 41 00
ROUGH CARPENTRY
FINISH CARPENTRY
ARCHITECTURAL WOOD CASEWORK
DIVISION 07 - THERMAL AND MOISTURE PROTECTION
07
07
07
07
07
07
07
07
07
07
07
07
07
11
13
16
21
41
42
54
62
71
72
84
84
92
13
00
16
00
13
13
23
00
00
00
13
43
00
BITUMINOUS DAMPPROOFING
SELF-ADHERING SHEET WATERPROOFING
CRYSTALLINE WATERPROOFING
THERMAL INSULATION
METAL ROOF PANELS
METAL WALL PANELS
THERMOPLASTIC POLYOLEFIN (TPO) ROOFING
SHEET METAL FLASHING AND TRIM
ROOF SPECIALTIES
ROOF ACCESSORIES
PENETRATION FIRESTOPPING
FIRE RESISTIVE JOINT SYSTEMS
JOINT SEALANTS
DIVISION 08 - OPENINGS
08 11 10
08 14 16
08 17 13
STEEL DOORS AND FRAMES
FLUSH WOOD DOORS
INTEGRATED METAL DOOR OPENING ASSEMBLIES
Table of Contents
TOC - 1
Grimm + Parker Architects Project No. 21145.00
08
08
08
08
08
08
08
08
08
08
08
31
33
33
41
44
51
63
71
80
83
90
00
23
26
13
13
13
00
00
00
00
00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ACCESS DOORS AND FRAMES
OVERHEAD COILING DOORS
OVERHEAD COILING GRILLES
ALUMINUM FRAMED ENTRANCES AND STOREFRONTS
GLAZED ALUMINUM CURTAIN WALLS
ALUMINUM WINDOWS
METAL FRAMED SKYLIGHTS
DOOR HARDWARE
GLAZING
MIRRORS
LOUVERS
DIVISION 09 - FINISHES
09
09
09
09
09
09
09
09
09
09
09
09
09
09
21
22
30
51
52
54
64
65
68
84
91
91
93
96
16
16
00
00
50
50
66
00
00
00
13
23
00
00
GYPSUM BOARD ASSEMBLIES
NON LOAD-BEARING STEEL FRAMING
TILING
ACOUSTICAL TILE CEILINGS
INTERACTIVE ACOUSTICAL PANEL SYSTEM
FRP CEILING SYSTEM
WOOD ATHLETIC FLOORING
RESILIENT FLOORING
CARPETING
ACOUSTICAL ROOM COMPONENTS
EXTERIOR PAINTING
INTERIOR PAINTING
WOOD STAINS AND TRANSPARENT FINISHES
HIGH-PERFORMANCE COATINGS
DIVISION 10 - SPECIALTIES
10
10
10
10
10
10
10
10
10
10
10
11
14
21
21
22
28
44
50
56
73
75
01
00
13
23
26
00
00
00
13
00
00
VISUAL DISPLAY SURFACES
SIGNAGE
TOILET COMPARTMENTS
CUBICLE CURTAINS
OPERABLE PARTITIONS
TOILET ACCESSORIES
FIRE PROTECTION SPECIALTIES
LOCKERS
METAL STORAGE SHELVING
PROTECTIVE COVERS
FLAGPOLES
DIVISION 11 - EQUIPMENT
11
11
11
11
11
11
11
11
11
13
31
40
51
51
52
61
66
66
00
00
00
19
23
13
42
23
53
LOADING DOCK EQUIPMENT
APPLIANCES
FOOD SERVICE EQUIPMENT
BOOK THEFT PROTECTION EQUIPMENT
LIBRARY STACK SYSTEMS
PROJECTION SCREENS
PLATFORM CURTAINS
GYMNASIUM EQUIPMENT
GYMNASIUM DIVIDERS
Table of Contents
TOC - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
DIVISION 12 - FURNISHINGS
12
12
12
12
12
24
35
35
35
48
13
50
51
53
13
WINDOW SHADE SYSTEMS
EDUCATIONAL CASEWORK
MUSIC INSTRUMENT STORAGE CABINETS
LABORATORY CASEWORK
ENTRANCE FLOOR MATS
DIVISION 14 - CONVEYING EQUIPMENT
14 20 10
14 42 00
ELEVATORS
WHEELCHAIR LIFTS
Table of Contents
TOC - 3
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 01 10 00 - SUMMARY
PROJECT INCLUDES
1.1 PROJECT DESCRIPTION
A. Project Location: Winchester, Virginia.
B.
Project Summary: Design and construction of a new 687 student John Kerr Elementary School
and an expansion to Frederick Douglass Elementary School.
1.2 PAYMENT PROCEDURES
A. Application for Payment: AIA G702 with G703, Continuation Sheet.
B.
Payment Application Time: Submit to Architect pencil copy for review one week prior to
end-of-month pay requisition meeting for period covering current month.
1.3 TESTING
A. Testing Agency: Independent testing agency engaged and paid for by Owner.
B.
Contractor Responsibilities: Quality-control services specified and required by authorities
having jurisdiction.
1.4 COORDINATION
A. Coordination: Coordination of site work, utilities, and building construction.
B.
Schedule: Critical path method (CPM) project schedule.
C.
All construction and work shown on the complete set of drawings is assumed to be new,
furnished and installed by the contractor, unless noted otherwise (U.N.O.).
1.5 FIELD ENGINEERING
A. Underground Utilities: Verification and location of underground utilities, facilities, and
equipment.
B.
Layout: Layout for site improvements, utilities, and structures.
1.6 PROJECT MEETINGS
A. Pre-Construction Conference: Attendance by Owner, Architect, Contractor, Engineers, major
subcontractors, and suppliers.
B.
Pre-installation Conferences: Before each construction activity that requires coordination with
other construction.
C.
Progress Meetings: Bi-weekly; attendance by Owner, Architect, Contractor, Engineers,
applicable subcontractors, and suppliers.
D. Coordination Meetings: At regular intervals, in addition to specific meetings held for other
purposes.
E.
Clarification of the Contract Documents: CSI Form 13.2A, "Request for Interpretation."
1.7 SUBMITTALS
A. Project Submittals: Reproducible plus six copies of shop drawings; six copies for product
data; and three representative units for samples.
B.
Record Documents: As-built drawings, record specifications, maintenance manuals, and final
property survey.
SUMMARY
01 10 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
1.8 TEMPORARY FACILITIES
A. Temporary Utility Service: New temporary utility services.
B.
Temporary Facilities: Temporary construction, support facilities, and security measures.
C.
Temporary Office Equipment: Telephones, facsimile (fax) machine, computer, and digital
camera available for use by Architect.
END OF SECTION
SUMMARY
01 10 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 03 30 00 - CAST-IN-PLACE CONCRETE
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Plant-mixed Cast-in-Place Concrete
1. Footings and foundations.
2. Foundation walls.
3. Slabs-on-grade.
4. Formed elevated slabs.
1.2 QUALITY ASSURANCE
A. Standards: ACI 318, Building Code Requirements for Reinforced Concrete, and CRSI Manual
of Standard Practice.
B.
Testing: Independent testing laboratory.
C.
Floor Flatness and Levelness Tolerances:
1.
Subfloors Under Thin Floor Coverings: ASTM E 1155, minimum local values of
flatness, F (F) 24; and levelness, F (L) 17; for slabs-on-grade.
2.
Subfloors Under Carpet: ASTM E 1155, minimum local values of flatness F (F) 17; and
levelness, F (L) 15.
1.3 PRODUCTS
A. Concrete Design Mixes, ASTM C 94, 28 Day Compressive Strength:
1.
Columns, Foundations, and Footings: 3000 psi.
2.
Slabs on Grade: 3500 psi.
3.
Concrete on Metal Deck: 3000 psi.
4.
Formed Elevated Slabs: 5000 psi.
5.
Walls: 4000 psi.
B. Formwork: Plywood or metal panel formwork sufficient for structural and visual
requirements.
1.
Special forms for textured finish concrete.
2.
Metal, plastic or paper tubes for cylindrical columns and supports.
C. Reinforcing Materials:
1.
Reinforcing Bars: ASTM A 615, Grade 60, deformed.
2.
Steel Wire: ASTM A 82.
3.
Steel Wire Fabric: ASTM A 185 welded.
4.
Concrete Reinforcing Fibers:
a. 100 percent virgin polypropylene fibrillated fibers specifically manufactured for use as
concrete reinforcement, containing no reprocessed olefin materials.
b. Fibrous concrete reinforcement shall conform to ASTM C1116 Type 3.
c. Physical Characteristics:
1) Specific Gravity: 0.91.
2) Tensile Strength: 70 to 100 ksi.
3) Fiber lengths 1/2 inch or 3/4 inch.
d. Flexural toughness parameters defined in ASTM C1018 shall equal or exceed the
requirements for Performance Level 1.
CAST-IN-PLACE CONCRETE
03 30 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
D. Concrete Materials: ASTM C 150, Type I, Portland cement; ASTM C 33 normal weight
aggregates; potable water.
1. ASTM C 33, normal weight aggregates.
2. ASTM C 330, light weight aggregates.
a. Fly ash not permitted; blast furnace slag to be incorporated for recycled content.
E. Concrete Admixtures: Containing less than 0.1 percent chloride ions.
1. Air-Entraining Admixture: ASTM C 260, for exterior exposed concrete and foundations
exposed to freeze-thaw.
2. Water-Reducing Admixture: ASTM C 494, Type A, for placement and workability.
F. Auxiliary Materials:
1. Vapor Retarder:
a. WVTR less than or equal to 0.006 gr/ft2/hr as tested by ASTM E 96.
b. ASTM E 1745 Class A (Plastics)
c. Provide standard accessories and tape for complete system.
d. Vapor Barrier Products:
1) Stego Wrap (15-mil) Vapor Barrier by STEGO INDUSTRIES LLC.
2. Nonslip Aggregate Finish: Fused aluminum oxide granules or crushed emery.
3. Curing Materials: Clear, waterborne, membrane-forming curing, dissipating; and clear,
waterborne, membrane-forming curing and sealing compound
4. Bonding Compound: Polyvinyl acetate or acrylic base.
5. Epoxy Adhesive: ASTM C 881, two-component material.
6. Waterstops: Self-expanding bentonite strip.
G. Concrete Finishes For Formed Surfaces:
1. Surfaces Not Exposed To View: As-cast form finish.
2. Surfaces Exposed To View: Smooth form finish.
H. Concrete Finishes for Monolithic Slabs:
1. Trowel finish for surfaces to be exposed to view or covered with resilient flooring, carpet,
tile, or other thin finish system.
2. Trowel and fine broom finish for surfaces to receive thin-set ceramic or quarry tile.
3. Nonslip broom finish for exterior concrete platforms, steps, and ramps.
I. Floor and Slab Treatments: Penetrating liquid floor treatment on exposed interior concrete
floors.
1. Location: Horizontal concrete surfaces remaining exposed (without additional finish
material).
END OF SECTION
CAST-IN-PLACE CONCRETE
03 30 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 04 20 00 - UNIT MASONRY ASSEMBLIES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Unit Masonry Construction:
1.
Brick and concrete block cavity walls.
2.
Concrete block non-bearing partitions.
3.
Concrete block bearing partitions.
4.
High density prefinished concrete masonry units.
1.2 QUALITY ASSURANCE
A. Standards: ACI 530.1, Specifications for Masonry Structures.
B.
Fire Performance: ASTM E 119.
C.
High Density Units: ASTM C90-96
D. Testing: Independent testing laboratory.
E.
Field-Constructed Mock-Up: Typical exterior masonry construction.
1.3 PRODUCTS
A. Face
1.
2.
3.
4.
5.
Brick:
Size: Modular.
Color to be selected from manufacturer’s full range of colors.
Grade: ASTM C 216, Grade SW, Type FBX for general exposed use.
Special Shapes: As required by building configuration.
Bond Pattern: Running bond.
B. Concrete Masonry Units:
1.
Hollow and Solid Load-Bearing Concrete Masonry Units: ASTM C 90, 1900 psi
compressive strength, medium weight.
2.
Size: Face dimension of 7-5/8 inches high by 15-5/8 inches long by width required for
application.
3.
Special Shapes: As required by building configuration.
4.
Bond Pattern: Running Bond.
C. High Density Masonry Units:
1.
All units shall conform to ASTM C90-96.
2.
All units shall have a Ground Face finish, or as noted on the drawings.
3.
All units shall have an Integral Water-Repellant Admixture mixed in
during production.
4.
Basis-of-Design: Prairie Stone by Northfield Block Co.
D. Mortar and Grout:
1.
Portland Cement-Lime Mix: Packaged blend of portland cement complying with ASTM
C 150, Type I or Type III, and hydrated lime complying with ASTM C 207.
2.
Mortar Aggregate: Natural color, ASTM C 144.
3.
Color: Colored pigmented mortar.
4.
Selection: To be selected by Architect.
5.
Grout Aggregate: ASTM C 404.
E. Reinforcing Steel:
1. Reinforcing Bars: ASTM A 615, Grade 60.
UNIT MASONRY ASSEMBLIES
04 20 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
F. Joint Reinforcing: Welded wire with deformed side rods.
1.
Steel Wire: 9 gage galvanized steel.
2.
Type: Ladder or truss type.
G. Ties and Anchors:
1.
Bent Wire Ties: Galvanized steel.
2.
Masonry to Steel Frame: Anchor with crimped wire anchor section for welding to steel.
3.
Adjustable Masonry Veneer Anchors: Screw-attached two-piece galvanized triangular or
rectangular wire tie and metal anchor, Hohmann and Barnhard, Inc., DW-10 with 5" V
tie, hot dipped galvanized, 16" O.C. horizontal and 16" O.C. vertically.
4.
Anchor Bolts: ASTM A 307, Grade A, galvanized.
5.
Post installed Anchors: Expansion anchors.
H. Masonry Accessories:
1.
Cavity Drainage Material: Nylon, high-density polyethylene (HDPE), or polyester in a
90% woven mesh.
2.
Rubberized - Asphalt Flashing: Manufactures standard composite flashing product
consisting of a pliable and highly adhesive rubberized-asphalt compound, bonded to a
high density, cross laminated polyethylene film to produce an overall thickness of 0.030
inches.
3.
Nonmetallic expansion joint strips.
4.
Preformed control joint gaskets.
5.
Bond breaker strips.
6.
Polypropylene honeycomb head weeps.
END OF SECTION
UNIT MASONRY ASSEMBLIES
04 20 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 04 72 00 - CAST STONE MASONRY
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Cast stone units.
1.2 QUALITY ASSURANCE
A. Manufacturer: Member of the Cast Stone Institute.
B.
Compressive Strength: Not less than 6500 psi at 28 days.
C.
Average Water Absorption: Not exceed 6 percent by dry weight.
1.3 PRODUCTS
A. Cast Stone: Fed. Spec. SS-S-721, Type I, (smooth finish panels), reinforced with steel rods.
1.
Portland Cement: ASTM C150, Type I
2.
Cement - Portland Type I or Type III white meeting ASTM C 150.
3.
Aggregate: Graded and washed natural sands, or manufactured granite, quartz or
limestone sands meeting ASTM C 33.
4.
Air Entrainment: ASTM C 260; Wet cast mixtures shall contain 5 to 7 percent air
entrainment.
5.
Mix to contain integral water repellant accepted by manufacturer.
6.
Steel Reinforcing Bars: ASTM A615, Grade 40; deformed bars.
7.
Color: ASTM C 979, custom.
1.4 MANUFACTURERS
A. Arban Precast Stone, Ltd.
B.
Continental Cast Stone Manufacturing, Inc.
C.
RockCast by Reading Rock, Inc.
D. York.
E.
Kerckhoff: D.C. Kerckhoff Co.
F.
Russell: W.N. Russell & Co.
G. Stafford Stone Works.
END OF SECTION
CAST STONE MASONRY
04 72 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
CAST STONE MASONRY
04 72 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 05 12 00 - STRUCTURAL STEEL
FRAMING PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Structural steel framing members, support members and struts.
B.
Base plates, shear stud connectors and expansion joint plates.
C.
Grouting under base plates.
1.2 QUALITY ASSURANCE
A. Fabricate structural steel members in accordance with AISC “Steel Construction Manual”.
B.
Comply with Section 10 of AISC “Code of Standard Practice for Steel Buildings and Bridges”
for architecturally exposed structural steel.
C.
Design connections not detailed on the drawings under the direct supervision of a Professional
Structural Engineer experienced in design of this work and licensed in the Commonwealth of
Virginia.
1.3 PRODUCTS
A. Steel Angles and Plates: ASTM A 36/A 36M.
B.
Steel W Shapes and Tees: ASTM A 992/A 992M.
C.
Cold-Formed Structural Tubing: ASTM A 500, Grade B.
D. Hot-Formed Structural Tubing: ASTM A 501, seamless or welded.
E.
Pipe: ASTM A 53/A 53M, Grade B, Finish Black.
F.
Shear Stud Connectors: Made from ASTM A 108 Grade 1015 Bars.
G. High-Strength Structural Bolts, Nuts and Washers: ASTM A 325 (ASTM A 325M), Type 1,
medium carbon, plain.
H. High-Strength Structural Bolts: ASTM A 490 (ASTM A 490M), with matching ASTM A 563
(ASTM A 563M) nuts and ASTM F 436 washers; Type 1 alloy steel.
I.
Grout: Non-shrink, non-metallic aggregate type, complying with ASTM C 1107/C 1107M and
capable of developing a minimum compressive strength of 7,000 psi at 28 days.
END OF SECTION
STRUCTURAL STEEL FRAMING
05 12 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
STRUCTURAL STEEL FRAMING
05 12 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 05 21 00 - STEEL JOISTS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Steel joists for roof framing.
1.2 QUALITY ASSURANCE
A. Standards: Steel Joist Institute Standard Specifications.
1.3 PRODUCTS
A. Steel
1.
2.
3.
Materials:
Types: K-series, LH-series and DLH-series open web steel joists.
Steel: SJI specifications for chord and web sections.
Steel Bearing Plates: ASTM A 36.
B. Auxiliary Materials:
1.
Unfinished Threaded Fasteners: ASTM A 307, Grade A.
2.
Steel Prime Paint: SJI specifications.
END OF SECTION
STEEL JOISTS
05 21 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
STEEL JOISTS
05 21 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 05 31 00 - STEEL DECKING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Galvanized steel roof deck; 1-1/2 inches.
B.
Composite steel floor deck; 3 inches.
C.
Non-composite steel form deck; 9/16 inches and 1-1/2 inches.
D. Acoustical roof deck.
1.2 QUALITY ASSURANCE
A. Standards: AISI, Specification for the Design of Cold-Formed Steel Structural Members; and
SDI Design Manual for Composite Decks, Form Decks, and Roof Decks.
B.
Approvals: UL label and FM listing.
1.3 PRODUCTS
A. Steel Materials and Finish:
1.
Prime-Painted Steel sheet: ASTM A 611.
2.
Galvanized Steel Sheet: ASTM A 653, Structural Steel (SS), Grade 33, G60 zinc coating.
3.
Steel Shapes: ASTM A 36.
4.
Shear Connectors: Headed stud type, ASTM A 108.
5.
Sheet Metal Accessories: ASTM A 526, commercial quality, galvanized.
6.
Galvanizing Repair: ASTM A 780.
7.
Paint: Baked-on rust-inhibitive paint.
B. Auxiliary Materials:
1.
Metal cover plates.
2.
Metal closure strips.
END OF SECTION
STEEL DECKING
05 31 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
STEEL DECKING
05 31 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 05 40 00 - COLD-FORMED METAL FRAMING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Exterior and interior load-bearing wall framing.
B.
Exterior lateral force-resisting framing.
1.2 QUALITY ASSURANCE
A. Standards: AISI, Specification for Design of Cold-Formed Steel Structural Members.
B.
Deflection Criteria: L/360 for non-load bearing curtainwalls.
C.
Fabrication Tolerances: 1/8 inch in 10 feet.
D. Erection Tolerances: 1/16 inch.
1.3 DESIGN DELAGATION
A. Engineering design of cold-formed metal framing by Contractor.
1.4 PRODUCTS
A. Cold-Formed Metal Framing Materials:
1.
Stud Type: C-shaped or SIGMA load-bearing steel studs.
2.
Steel Sheet: ASTM A 653/A 653M, structural steel, zinc coated, Grade 33.
3.
Coating: G60.
B. Auxiliary Materials:
1.
Fasteners.
2.
Electrodes for welding.
3.
Galvanizing repair, ASTM A 780.
END OF SECTION
COLD-FORMED METAL FRAMING
05 40 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
COLD-FORMED METAL FRAMING
05 40 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 05 50 00 - METAL FABRICATIONS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Metal
1.
2.
3.
4.
5.
6.
7.
Fabrications:
Ladders.
Loose bearing and leveling plates.
Loose steel lintels.
Miscellaneous steel trim.
Shelf and relieving angles.
Pipe bollards.
Rough hardware.
1.2 QUALITY ASSURANCE
A. Design Engineering: Registered engineer in the Commonwealth of Virginia.
1.3 PRODUCTS
A. Ferrous Materials:
1.
Steel Plates, Shapes and Bars: ASTM A 36.
2.
Steel Tubing: ASTM A 500 or A 501.
3.
Uncoated Structural Steel Sheet: ASTM A 611 or A 570.
4.
Uncoated Steel Sheet: ASTM A 366 or A 569.
5.
Galvanized Steel Sheet, Structural Quality: ASTM A 446, Grade A, G90.
6.
Galvanized Steel Sheet, Commercial Quality: ASTM A 526, G90.
7.
Steel Pipe, Black Finish: ASTM A 53.
8.
Steel Pipe, Galvanized Finish: ASTM A 53.
9.
Gray Iron Castings: ASTM A 48, Class 30.
10. Malleable Iron Castings: ASTM A 47, Grade 32510.
11. Reinforcing Bars: ASTM A 615, Grade 60.
12. Brackets, Flanges, and Anchors: Cast or formed metal.
13. Concrete Inserts: Threaded or wedge type.
14. Welding Rods and Bare Electrodes: AWS specifications.
15. Zinc-Coating: Hot-dip galvanized coating for materials in exterior assemblies or exterior
walls.
B. Fasteners:
1.
Bolts and Nuts: Hexagon head type, ASTM A 307, Grade A.
2.
Lag Bolts: Square head, FS FF-B-561.
3.
Machine Screws: Cadmium plated steel, FS FF-S-92.
4.
Wood Screws: Flat head carbon steel, FS FF-S-111.
5.
Plain Washers: Round carbon steel, FS FF-W-92.
6.
Drilled-In Expansion Anchors: FS FF-S-325.
7.
Toggle Bolts: Tumble-wing type, FS FF-B-588.
8.
Lock Washers: Spring type carbon steel, FS FF-W-84.
9.
Zinc-Coating: Fasteners in exterior assemblies or exterior walls.
C. Auxiliary Materials:
1.
Nonshrink Metallic Grout: CE CRD-C621.
2.
Nonshrink Nonmetallic Grout: CE CRD-C621.
METAL FABRICATIONS
05 50 00 - 1
Grimm + Parker Architects Project No. 21145.00
3.
4.
5.
6.
7.
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
Interior Anchoring Cement: Hydraulic expansion cement.
Exterior/Interior Anchoring Cement: Erosion-resistant hydraulic expansion cement.
Shop Primer: Alkyd primer, FS TT-P-645.
Galvanizing Repair Paint: SSPC - Paint 20.
Bituminous Paint: Asphalt mastic, SSPC - Paint 12.
1.4 FABRICATIONS
A. Miscellaneous Framing and Supports:
1.
Steel framing and supports for countertops, mechanical and electrical equipment,
and applications where framing and supports are not specified in other Sections.
2.
Support angles for elevator door sills.
3.
Galvanize where indicated.
4.
Prime with zinc-rich primer where indicated.
B. Loose steel lintels, galvanized at exterior walls and field painted.
C. Loose bearing and leveling plates, galvanized.
D. Steel weld plates and angles not specified in other Sections, for casting into concrete.
E. Miscellaneous Steel Trim: Steel angle corner guards and loading-dock edge angles. 1.
Galvanize exterior locations.
F. Metal Ladders including Elevator Pit Ladders: Steel. 1.
Prime interior locations with zinc-rich primer.
G. Metal Bollards: Schedule 40 steel pipe galvanized and field painted.
H. Elevator Sump Pit Grate: Aluminum frame and grate.
END OF SECTION
METAL FABRICATIONS
05 50 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 05 51 00 - METAL STAIRS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Stairs with concrete treads.
B. Structural steel stair framing and supports.
1.2 QUALITY ASSURANCE
A. Design Engineering: Registered engineer in the Commonwealth of Virginia.
1.3 PRODUCTS
A. Provide stairs of the design specified, complete with landing platforms, vertical and horizontal
supports, railings, and guards, fabricated accurately for anchorage to each other and to building
structure.
1.
Regulatory Requirements: Provide stairs and railings complying with the most stringent
requirements of local, state, and federal regulations; where requirements of the contract
documents exceed those of regulations, comply with the contract documents.
2.
Structural Design: Provide complete stair and railing assemblies complying with the
applicable local code.
B. Risers: Closed.
C. Treads: Metal pan with field-installed concrete fill.
1.
Concrete Depth: 1-1/2 inches, minimum; 3000 psi concrete.
2.
Tread Pan Material: Steel sheet; CS (commercial steel).
3.
Tread Pan Thickness: As required by design; 14 gage, 0.075 inch minimum.
4.
Concrete Reinforcement: None.
5.
Concrete Finish: For resilient floor covering.
1.4 Risers: Same material and thickness as tread pans.
A. Nosing Depth: Not more than 1-1/2 inch overhang.
B. Nosing Return: Flush with top of concrete fill, not more than 1/2 inch wide.
1.5 Stringers: Rolled steel channels.
A. Stringer Depth: As indicated on drawings.
B. End Closure: Sheet steel of same thickness as risers welded across ends.
1.6 Landings: Same construction as treads, supported and reinforced as required to achieve design load
capacity.
1.7 Finish: Shop- or factory-prime painted.
1.8 Under Side of Stair: Exposed to view, to be finished same as specified for other exposed to view
surfaces.
END OF SECTION
METAL STAIRS
05 51 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
METAL STAIRS
05 51 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 05 52 13 - PIPE AND TUBE RAILINGS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Pipe and tube handrails and railing systems.
1.2 QUALITY ASSURANCE
A. Design Engineering: Registered engineer in the Commonwealth of Virginia.
B.
Handrail and Railing Structural Performance: ASTM E 985.
1.3 PRODUCTS
A. Steel Pipe and Tube Railing Systems:
1.
Steel Pipe, Galvanized Finish: ASTM A 53.
2.
Steel Tubing: ASTM A 500 or A 501.
3.
Steel Plates, Shapes and Bars: ASTM A 36.
4.
Gray Iron Castings: ASTM A 48, Class 30.
5.
Malleable Iron Castings: ASTM A 47, Grade 32510.
6.
Finish: Primed (interior)
7.
Finish: Galvanized and shop primed (exterior).
B. Auxiliary Materials:
1.
Nonshrink Nonmetallic Grout: CE CRD-C621.
2.
Exterior/Interior Anchoring Cement: Erosion-resistant hydraulic expansion cement.
3.
Shop Primer: Alkyd primer, FS TT-P-645.
4.
Galvanizing Repair Paint: SSPC Paint 20.
5.
Bituminous Paint: Asphalt mastic, SSPC Paint 12.
C. Infill Panels: 1/2” x 1/2” square vertical pickets at 4” o.c. spacing between vertical pickets.
PIPE AND TUBE RAILINGS
05 52 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
PIPE AND TUBE RAILINGS
05 52 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 06 10 00 - ROUGH CARPENTRY
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Rough Carpentry:
1.
Framing with dimensional lumber
2.
Wood grounds, nailers, furring and blocking
1.2 QUALITY STANDARDS
A. Lumber Standards and Grade Stamps: PS 20, American Softwood Lumber Standard and
inspection agency grade stamps.
B.
Construction Panel Standards: PS 1, U.S. Product Standard for Construction and Industrial
Plywood; APA PRP-108.
C.
Preservative Treatment: AWPA C2 for lumber and AWPA C9 for plywood; waterborne
pressure treatment.
D. Fire-Retardant Treatment: AWPA C20 for lumber and AWPA C27 for plywood; non-corrosive
type.
1.3 PRODUCTS
A. Dimension Lumber:
1. For light non-load bearing framing (2 to 4 inches thick, 2 to 4 inches wide) Provide the
following grade and species.
a. No. 2 grade, or Stud grade.
b. Refer to structural drawings for additional info on grade and species.
c. Finger joint studs (option) at non-bearing partitions only.
2. All wood in contact with concrete and masonry to be preservative treated by pressure
process. This includes wood sills, floor plates, sleepers, blocking, furring, stripping and
similar concealed members and wood framing members less than 18 inches above grade.
B. Miscellaneous Lumber:
1.
Moisture Content: 19 percent
2.
Grade: Standard grade light framing.
END OF SECTION
ROUGH CARPENTRY
06 10 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ROUGH CARPENTRY
06 10 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 06 20 00 - FINISH CARPENTRY
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Finish carpentry items.
B.
Shop finishing of finish carpentry work.
1.2 MATERIAL
A. Wood fabricated from old growth timber is not permitted.
B.
Hardwood Lumber: Maple species, plain sawn, maximum moisture content of 6 percent, of
quality suitable for transparent finish.
C.
Hardwood Plywood: HPVA HP-1, Grade AA, Type II; Veneer core, type of glue
recommended for application; Maple face species, plain sliced.
1.3 WORKMANSHIP
A. Perform work in accordance with AWI Architectural Woodwork Quality Standards Illustrated,
Custom grade.
B.
Finish work in accordance with AWI Architectural Woodwork Quality Standards
Illustrated, Section 1500:
1.
Transparent: Conversion varnish (formerly TR-4).
2.
Opaque: Catalyzed polyurethane (formerly OP-6).
END OF SECTION
FINISH CARPENTRY
06 20 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
FINISH CARPENTRY
06 20 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 06 41 00 - ARCHITECTURAL WOOD CASEWORK
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Interior Architectural Woodwork:
1.
Interior standing and running trim.
2.
Wood cabinets.
3.
Countertops.
4.
Cubbies and storage cubicles.
5.
Library circulation desk.
6.
Wood shelving.
7.
Miscellaneous millwork items.
8.
Shop finishing of woodwork.
1.2 QUALITY ASSURANCE
A. Standards: Architectural Woodwork Institute (AWI) "Architectural Woodwork Quality
Standards."
1.3 PRODUCTS
A. Interior Standing and Running Trim:
1.
Species for Transparent Finish: Plain sawn clear maple.
2.
Species for Opaque Finish: Any closed-grain hardwood
3.
Grade: Premium.
B. Interior Wood Casework:
1.
Species for Transparent Finish: Plain sawn select white birch.
2.
Grade: Premium.
3.
Face Style: Flush overlay.
4.
Frame Fabrication: Frameless.
5.
Grain Matching: Vertical.
6.
Veneer Matching of Leaves: Book.
7.
Veneer Matching In Panel Face: Running.
C. Interior Laminate-Clad Casework:
1.
Laminate: High pressure decorative laminate, NEMA LD-3; Grade HGS.
2.
Grade: Premium.
3.
Face Style: Flush overlay.
4.
Frame Fabrications: Frameless.
D. Casework Hardware and Auxiliary Materials:
1.
Hardware Standard: ANSI/BHMA A156.9.
2.
Hardware Finish and Base Metal: Satin chromium plated steel.
E. Interior Laminate-Clad Countertops:
1.
Laminate: High pressure decorative laminate, NEMA LD-3; Grade HGS.
2.
Grade: Premium.
3.
Core: Plywood.
4.
Edge: Laminate or clear maple hardwood.
F. Auxiliary Materials:
1. Anchors: Type required for secure anchorage.
ARCHITECTURAL WOOD CASEWORK
06 41 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
G. Finishing:
1. Transparent Finish: Premium grade with or without stain with dull satin sheen; AWI
Finish System TR-6, catalyzed polyurethane.
END OF SECTION
ARCHITECTURAL WOOD CASEWORK
06 41 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 11 13 - BITUMINOUS DAMPPROOFING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Cold trowel-applied asphalt bituminous dampproofing.
1.2 PRODUCTS
A. Asphalt Primer: ASTM D41.
B.
Fibered Trowel Mastic: Solvent-based, ASTM D4586 Type 1 (Non-Asbestos), Perm Rating:
0.25 metric perms @ 40 mils dry film.
C.
Fibered Trowel-grade Emulsion Mastic: Water-based emulsion, ASTM D1227 Type II, Class
1, Perm Rating 0.5 mg/sq. cm.
1.3 MANUFACTURERS
A. Henry Company.
B.
Karnak Corp.
C.
W.R. Meadows.
END OF SECTION
BITUMINOUS DAMPPROOFING
07 11 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
BITUMINOUS DAMPPROOFING
07 11 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 13 00 - SELF-ADHERING SHEET WATERPROOFING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Sheet Membrane Waterproofing Systems:
1. Foundation walls and footings where floor elevation is below finished grade.
1.2 PRODUCTS
A. Rubberized Asphalt Sheet Waterproofing: Self-adhering rubberized asphalt and polyethylene
sheet membrane, 56 mils thick, tensile strength 250 psi.
B.
Molded-Sheet Drainage Panel: Prefabricated, composite drainage panels, manufactured with a
permeable geotextile facing laminated to a molded-plastic-sheet drainage core.
1. Compressive Strength: 10,000 psi, minimum; ASTM D 1621.
2. Flow Rate: 100 gpm per ft., minimum, at hydraulic gradient of 1.0 and compressive stress
of 25 psi; ASTM D 4716.
1.3 MANUFACTURERS
A. American Hydrotech, Inc.; VM 75.
B.
Carlisle Corporation, Carlisle Coatings & Waterproofing Div.; CCW 701.
C.
Cetco; Envirosheet.
D. W. R. Grace & Co.; Bituthene 3000.
E.
W. R. Meadows, Inc.; Mel-Rol.
F.
Monsey Bakor; Elasto-Seal 2000.
G. Pecora Corporation; Duramem 700-SM.
H. Polyguard Products, Inc.; Polyguard 650.
END OF SECTION
SELF-ADHERING SHEET WATERPROOFING
07 13 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SELF-ADHERING SHEET WATERPROOFING
07 13 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 16 16 - CRYSTALLINE WATERPROOFING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Crystalline Waterproofing: A prepackaged, proprietary blend of portland cement, specially
treated sand, and active chemicals that, when mixed with water and applied, penetrates by
capillary action into concrete and reacts chemically with free lime in the presence of water to
develop crystalline growth within concrete capillaries to produce an impervious, dense,
waterproof concrete.
B. Location: Interior surfaces of elevator pits.
1.2 PRODUCTS
A. Anti-Hydro International, Inc.; Hydro Cap.
B.
Tamms Industries, Inc.; Hey'Di K-11.
C.
Xypex Chemical Corporation; Xypex.
END OF SECTION
CRYSTALLINE WATERPROOFING
07 16 16 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
CRYSTALLINE WATERPROOFING
07 16 16 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 21 00 - THERMAL INSULATION
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Building Insulation and Vapor Retarders:
B.
Under slabs-on-grade, board type.
C.
Foundation walls, board type.
D. Thermal insulation, blanket/batt type.
1.2 PRODUCTS
A. Board Insulation: Extruded polystyrene, rigid, ASTM C 578.
B.
Blanket/Batt Insulation: Glass fiber or mineral slag fiber, ASTM C 665, Type I (blankets
without membrane facing), maximum flame-spread and smoke-developed indices of 25 and 50,
respectively.
1. Formaldehyde free.
C.
Faced Mineral-Fiber Blanket Insulation: Glass fiber or mineral slag fiber, ASTM C 665, Type
III, Class A (blankets with reflective vapor-retarder membrane facing and flame spread of 25 or
less); with foil-scrim-kraft, foil-scrim, or foil-scrim-polyethylene vapor-retarder membrane on
one face.
1.3 MANUFACTURERS
A. Extruded-Polystyrene Board Insulation:
1.
DiversiFoam Products.
2.
Dow Chemical Company.
3.
Owens Corning.
4.
Pactiv Building Products.
B. Glass-Fiber, Slag-Wool-Fiber and Rock-Wool-Fiber Insulation:
1.
CertainTeed Corporation.
2.
Johns Manville Corporation.
3.
Knauf Fiber Glass.
4.
Owens Corning.
5.
Fibrex Insulations Inc.
6.
Thermafiber.
END OF SECTION
THERMAL INSULATION
07 21 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
THERMAL INSULATION
07 21 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 21 27 - ENCLOSED CAVITY FOMAED INSULATION
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Foamed-in-place insulation in masonry cavity walls.
1.2 QUALITY ASSURANCE
A. Manufacturer Qualifications: Company specializing in manufacturing products of the type
specified in this section, with not less than five years of documented experience.
B.
Applicator Qualifications: Company specializing in performing work of the type specified,
with minimum three years of experience.
C.
Contractor shall be certified by ABAA for SPF air barrier systems. Contractor shall include
ABAA inspection and reports, submitted to Architect at each stage.
D. Contractor shall provide a written Safety Program, written Respirator Program and a written
Job Hazard Analysis.
1.3 MATERIALS
A. Insulation: Polyurethane type.
1.
Thermal Conductivity: When tested in accordance with ASTM C 518:
2.
Initial k value: 0.147.
3.
Water Vapor Transmission: 1.82 perms (1 inch SPF), measured in accordance with
ASTM E 96.
4.
Air Permeance: 0.000025 L/s/sq. m. at 75 Pa, when tested in accordance with ASTM E
2178.
5.
Compressive Strength: 22 psi, when tested in accordance with ASTM D 1621.
6.
Density: 2.0 lb/cu ft, when tested in accordance with ASTM D 1622.
7.
Surface Burning Characteristics: Flame spread/Smoke developed index of 25 / 350, when
tested in accordance with ASTM E 84 (4 inches SPF thickness).
8.
R-Value: Minimum of R-16.75.
9.
Thickness: 2 1/2 inches.
a. Variation from thickness will be no more than plus 1/2 inch and no less than minus
1/4 inch.
B. Adhesives, primers applied within the building waterproofing envelope: Comply
withlow-emitting requirements in Section 01 61 16.
C. Flexible Flashing - CMU Backup: For flashing not exposed to the exterior, use the following,
unless otherwise indicated:
1. Performance Requirements:
a. Tensile Strength (Membrane): ASTM D412 Die C; 800 psi.
b. Tensile Strength (Film): ASTM D412 Die C; 5,000 psi.
c. Elongation: ASTM D412 Die C; 200 percent miminum.
d. Puncture Resistance: ASTM E154; minimum 134 pound.
e. Tear Resistance-Initial: ASTM D1004; minimum 45 pound.
f. Tear Resistance-Propagation: ASTM D1938; minimum 5.0 lbf/in. width.
g. Permeance: ASTM E96-B; 0.03 perms maximum.
h. Water Absorption: ASTM D570; 0.1 percent maximum.
2. Product:
a. Basis-of-Design: Blueskin TWF, Manufactured by Henry.
ENCLOSED CAVITY FOMAED INSULATION
07 21 27 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
1.4 MANUFACTURERS
A. Basis-of-Design:
1. Permax 2.0 by Henry Company.
B.
The following manufacturer's will be considered as equal providing they meet performance
properties specified and current local code requirements:
1.
Ecobay CC by Bayer Materials Sciences.
2.
Permax 2.0 by Henry CompanyWalltite by BASF; www.basf-pfe.com.
3.
Corobond III by Johns Manville Company.
END OF SECTION
ENCLOSED CAVITY FOMAED INSULATION
07 21 27 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 41 13 - METAL ROOF PANELS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Metal Roof Panels:
1. Standing seam roof panels with standing mechanically locked seams.
B. Metal soffit panels.
1.2 QUALITY ASSURANCE
A. Wind Uplift: UL 580 for Class 90 wind uplift resistance.
1.3 WARRANTY
A. Finish Warranty: 20 years.
B.
Waterproof Warranty: 20 years.
1.4 PRODUCTS
A. Manufactured Roof Panels:
1.
Description: Formed with vertical ribs at panel edges and intermediate raised profile
between ribs; designed for sequential installation by mechanically attaching panels to
supports using concealed clips located under one side of panels and engaging
opposite edge of adjacent panels, and mechanically seaming panels together.
2.
Panel Materials: Aluminum-zinc alloy-coated steel sheet, 24 gage minimum thickness.
3.
Panel Width: Nominal 16 inches.
4.
Panel Profile: One raised section providing stiffening qualities.
5.
Seam Type: Standing “T” beam with cap cover seamed mechanically.
6.
Seam Height: Minimum 2-3/8 inches with additional metal in the joinery, or minimum 3
inches with two piece clip design.
7.
Self-Adhering, Polymer-Modified, Bituminous Sheet Underlayment: ASTM D 1970,
minimum of 40 mils thick.
8.
Finish: Smooth with fluoropolymer, Kynar 500 coating.
B. Insulation: Polyisocyanurate installed between Z-Purlins.
C. Snow Guard System:
1.
Basis-of-Design: Snobar by Action Manufacturing.
2.
Design: Shall be seam mounted, non-penetrating.
D. Pipe Seals for Round Penetrations:
1.
Premolded EPDM boot with collar.
2.
Similar to Dektite by Buildtex.
E. Soffit Panels:
1.
Profile: Box style panel with squared-off pan and closing strip.
a. Basis-of-Design: “Linear Ceiling System, Type LCB” by Atas International, Inc.
2.
Material: Aluminum sheet.
3.
Finish: Smooth with fluoropolymer, Kynar 500 coating.
1.5 MANUFACTURERS
A. Roof Panels:
1. Merchant & Evans, Inc.; Zip-Rib.
METAL ROOF PANELS
07 41 13 - 1
Grimm + Parker Architects Project No. 21145.00
2.
3.
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
Centria Roof Systems; SRS 3.
Imetco; Series 300.
END OF SECTION
METAL ROOF PANELS
07 41 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 42 13 - METAL WALL PANELS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Factory-formed and field-assembled, concealed-fastener, interlocking horizontal seam metal
wall panels.
1.2 WARRANTY
A. Finish Warranty: 20 years.
B.
Weathertightness: 5 years.
1.3 PRODUCTS
A. Architectural Wall Panels: Concealed fastener wall panels with offset double tongue and
groove joinery and an extended metal shelf allowing fasteners to penetrate both metal faces
with clips concealed in the side joint.
1.
Face Profile: Flat, smooth.
2.
Exterior Face: Minimum 22 gauge galvanized steel.
3.
Interior Face: Minimum 26 gauge galvanized steel.
4.
Foam Core: Non-CFC, Class I, polyurethane.
5.
Thickness: 2 inches.
B. Exterior Finish: 3-coat fluoropolymer.
1.4 MANUFACTURERS
A. Benchmark, A Metecno Group Company; Designwall 2000.
B. Centria; Formawall.
C. Metl-Span I, Ltd.; CF Architectural Wall Panel. END
OF SECTION
METAL WALL PANELS
07 42 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
METAL WALL PANELS
07 42 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 54 23 - THERMOPLASTIC POLYOLEFIN (TPO) ROOFING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Fully adhered TPO sheet roofing system.
1.2 QUALITY ASSURANCE
A. Roofing System Design: Uplift pressures calculated according to ASCE 7.
B.
Listing: UL Class A, ASTM E 108, ASTM E 119external fire exposure, and Class 90 wind
uplift.
C. ASTM D 751, ASTM D 1149, ASTM D 573, ASTM D 471, ASTM D 1204.
1.3 WARRANTY
A. Roofing Warranty: Manufacturer's 20-year non pro-rated warranty.
1.4 PRODUCTS
A. Membrane:
1.
Material: Fabric-reinforced Thermoplastic Polyolefin sheet: uniform, flexible sheet
formed from a thermoplastic polyolefin, internally fabric or scrim reinforced.
2.
Minimum Thickness: 75 mils nominal.
3.
Color: White, Energy Star Approved.
B. Related Materials: Products to be manufactured by or approved by the primary membrane
manufacturer for the specified warranted roofing system.
C. Walkway pads located as shown on drawings.
1.5 MANUFACTURERS
A. James Manville
B.
Carlisle SynTec
C.
Firestone
D. Approved equal
END OF SECTION
THERMOPLASTIC POLYOLEFIN (TPO) ROOFING
07 54 23 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
THERMOPLASTIC POLYOLEFIN (TPO) ROOFING
07 54 23 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 62 00 - SHEET METAL FLASHING AND TRIM
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Metal counterflashing.
B.
Metal drip over windows and doors.
C.
Exposed metal trim.
D. Sheet metal accessories.
E.
Equipment flashing.
1.2 PRODUCTS
A. Sheet Metal Flashing and Trim:
1.
Zinc-Coated Steel: ASTM A 526, G90 hot-dip galvanized, 20 gage.
2.
Stainless Steel: AISI Type 302/304, ASTM A 167, 2D annealed finish, 28 gage.
3.
Sheet Aluminum: ASTM B 209, alloy 3003, clear anodized, 20 gage.
4.
Extruded Aluminum: 6063-T52, clear anodized, 0.080 inches for primary legs of
extrusion.
B. Fabricated Units: Compliance with SMACNA Architectural Sheet Metal Manual.
C. Auxiliary Materials:
1.
Solder compatible with metal.
2.
Bituminous isolation coating.
3.
Mastic and elastomeric sealants.
4.
Reglets and metal accessories.
5.
Asphaltic roofing cement.
END OF SECTION
SHEET METAL FLASHING AND TRIM
07 62 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SHEET METAL FLASHING AND TRIM
07 62 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 71 00 - ROOF SPECIALTIES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Prefabricated Roof Specialties:
1. Fascia and gravel stop systems.
1.2 PRODUCTS
A. Fascia and Gravel Stops: Aluminum sheet, 0.050 inch thick interlocking with 26 gage formed
zinc-coated steel water dam/hold down clip, compression clamp, and compression pad.
B.
Aluminum Gutters and Downspouts: Formed-aluminum sheet, 0.050 inch thick.
C.
Finishes: Fluoropolymer, Kynar 500.
1.3 MANUFACTURERS
A. Architectural Products Co.
B.
W.P. Hickman Co.
C.
Metal-Era, Inc.
D. MM Systems Corp.
END OF SECTION
ROOF SPECIALTIES
07 71 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ROOF SPECIALTIES
07 71 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 72 00 - ROOF ACCESSORIES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Roof Specialties and Accessories:
1.
Roof hatches (scuttles).
2.
Prefabricated curb and equipment support units.
1.2 LEED GOALS AND REQUIREMENTS
A. Credit MR 4.1 and 4.2: Product Data and certification letter indicating percentages by weight
of post-consumer and pre-consumer recycled content for products having recycled content.
Include statement indicating costs for each product having recycled content.
1. Contributions to this Credit include recycled content of steel and aluminum.
B.
Coordinate with Construction Waste Management requirements.
1.3 PRODUCTS
A. Roof
1.
2.
3.
Hatches:
Lid: Insulated metal lid.
Framing: Zinc-coated steel.
Curb Type: Insulated double wall curb.
B. Prefabricated Curb and Equipment Support Units:
1.
Type: Designed for roof type and equipment.
2.
Materials: Steel, 14 gage, hot dip galvanized.
1.4 MANUFACTURERS
A. Roof
1.
2.
3.
Hatches:
Babcock-Davis Hatchways, Inc.
Bilco Co.
Milcor, Inc.
B. Prefabricated Curb and Equipment Support Units:
1.
Curbs, Inc.
2.
Custom Curb, Inc.
3.
The Pate Co.
4.
Roof Products and Systems Corp.
5.
ThyCurb Div./ThyBar Corp.
END OF SECTION
ROOF ACCESSORIES
07 72 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ROOF ACCESSORIES
07 72 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 84 13 - PENETRATION FIRESTOPPING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Firestopping for the following:
1.
Penetrations through fire-rated construction.
2.
Construction gaps occurring within fire-rated construction.
3.
Sealant joints in fire-rated construction.
1.2 PRODUCTS
A. Firestop Systems: Through-penetration systems or devices listed in the UL Fire Resistance
Directory, the Warnock Hersey Firestop Systems Directory, or another qualified testing
agency, that conform to the construction type, penetrant type, annular space requirements and
fire rating for each separate instance.
END OF SECTION
PENETRATION FIRESTOPPING
07 84 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
PENETRATION FIRESTOPPING
07 84 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 84 43 - FIRE RESISTIVE JOINT
SYSTEMS PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Fire-resistive joint systems for the following applications:
1.
Floor-to-wall joints.
2.
Head-of-wall joints.
3.
Wall-to-wall joints.
1.2 QUALITY ASSURANCE
A. Fire Performance: Assemblies with ratings equaling or exceeding the fire-resistance of
construction that they join as determined by UL 2079.
B.
Perimeter Fire-Resistive Joint Systems: NFPA 285 and UL 2079.
C.
Coordination: Coordinate construction of joints to ensure fire-resistive joint systems are
installed according to specified requirements.
1.3 PRODUCTS
A. Fire-resistive joint systems that is compatible with joint substrates, under conditions of service
and application.
B.
Accessories: Components of fire-resistive joint systems as approved by qualified testing and
inspecting agency.
END OF SECTION
FIRE RESISTIVE JOINT SYSTEMS
07 84 43 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
FIRE RESISTIVE JOINT SYSTEMS
07 84 43 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 07 92 00 - JOINT SEALANTS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Joint sealers at interior and exterior vertical and horizontal joints.
1.2 PRODUCTS
A. Urethane Elastomeric Joint Sealants:
1.
Type and Application: Multi-part non-sag urethane sealant, ASTM C 920, for vertical
and horizontal joints, exterior and interior use.
2.
Type and Application: One-part pourable urethane sealant, ASTM C 920, for horizontal
joints, exterior use.
B. Silicone Elastomeric Joint Sealants:
1.
Type and Application: One-part nonacid-curing silicone sealant, ASTM C 920, for
vertical and horizontal joints, modulus as required for application, exterior and interior
use.
2.
Type and Application: One-part mildew-resistant silicone sealant, ASTM C 920, for
sanitary applications, interior use.
C. Latex Joint Sealants:
1.
Type: Acrylic-emulsion, ASTM C 834.
2.
Type: Silicone emulsion, ASTM C 834 and ASTM C 920.
3.
Application: Interior joints in vertical and overhead surfaces with limited movement.
D. Auxiliary Materials:
1.
Plastic foam joint fillers.
2.
Elastomeric tubing backer rods.
3.
Bond breaker tape.
END OF SECTION
JOINT SEALANTS
07 92 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
JOINT SEALANTS
07 92 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 11 10 - STEEL DOORS AND FRAMES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Steel
1.
2.
3.
Doors:
Interior steel doors and frames.
Exterior steel doors and frames.
Integral sidelights for doors and frames.
1.2 QUALITY ASSURANCE
A. Standards: ANSI/SDI-100, Recommended Specifications for Standard Steel Doors and
Frames.
B.
Performance Standards:
1.
Fire-Rated Assemblies: NFPA 80, and acceptable testing agency listing.
2.
Thermal-Rated Assemblies at Exterior: ASTM C 236 or ASTM C 976.
1.3 PRODUCTS
A. Steel
1.
2.
3.
4.
5.
Doors:
Door Type: Seamless steel doors with hollow or composite construction.
Interior Doors: ANSI 250.8, seamless, 20 gage.
Exterior Doors: ANSI A250.8, seamless, 18 gage, hot-dip galvannealed steel.
Accessories: Sightproof stationary louvers and glazing stops.
Finish: Factory primed and field painted.
B. Steel
1.
2.
3.
4.
Frames:
Interior Frames: Welded type; 18 gage for steel doors and wood doors.
Exterior Frames: Welded type; 16 gage hot-dip galvannealed steel for steel doors.
Accessories: Door silencers and plaster guards.
Finish: Factory primed and field painted.
1.4 MANUFACTURERS
A. Amweld Building Products, Inc.
B.
Ceco Door Products; a United Dominion Company.
C.
Curries Company.
D. Pioneer Industries Inc.
E.
Republic Builders Products.
F.
Steelcraft; a division of Ingersoll-Rand.
END OF SECTION
STEEL DOORS AND FRAMES
08 11 10 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
STEEL DOORS AND FRAMES
08 11 10 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 14 16 - FLUSH WOOD DOORS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Interior solid core flush doors.
1.2 QUALITY ASSURANCE
A. Quality Standards: AWI Architectural Quality Standards.
B.
Fire Rated Wood Doors: Complying with NFPA 252 requirements.
1.3 PRODUCTS
A. Interior Solid Core Doors:
1.
Grade: Custom, Grade A faces.
2.
Construction: 5-ply construction with [particleboard] [glued stave core or structural
composite lumber] core; stiles and rails bonded to core.
3.
Finish: Transparent finish on plain-sliced white maple faces.
B. Fitting and Finish:
1.
Fitting: Factory-prefit and premachine doors.
2.
Factory Finish: Transparent factory finish, AWI Finish System TR-6, catalyzed
polyurethane.
C. Auxiliary Materials:
1.
Metal louvers.
2.
Glazing frames.
a. Wood beads.
b. Wood-veneered beads for fire doors.
1.4 MANUFACTURERS
A. Algoma Hardwoods Inc.
B.
Eggers Industries; Architectural Door Division.
C.
Marshfield Door Systems, Inc.
D. Oshkosh Architectural Door Company.
E.
V-T Industries.
END OF SECTION
FLUSH WOOD DOORS
08 14 16 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
FLUSH WOOD DOORS
08 14 16 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 17 13 - INTEGRATED METAL DOOR OPENING
ASSEMBLIES PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Packaged cross corridor door pair assemblies and integrated door assemblies, including frames,
doors, operating hardware and installation accessories.
1.2 QUALITY ASSURANCE
A. Fire-rated door assemblies: Listed and labeled and complying with NFPA 80.
1.3 PRODUCTS
A. Frames: 16 gage; complying with SDI 100 and 111A; factory baked enamel finish.
B.
Doors: 1-3/4-inch thick; 20 gage bonderized steel sheets; solid polystyrene insulation bonded
to both door faces; [factory baked enamel] [wood veneer on metal] finish.
C.
Hardware:
1.
Lock Cylinders: Construction keyed with permanent cores and keys.
2.
Hinges: Semi-concealed continuous type; 14 gage electrogalvanized steel with 2-part
polyureathane finish.
3.
Hold-Opens: Electromagnetic.
4.
Closers: Parallel arm type.
5.
Kickplates: Stainless steel.
1.4 MANUFACTURERS
A. Total-Door Assembly; Openings, Inc.
B. INPACT Door System; Ingersoll-Rand Company.
END OF SECTION
INTEGRATED METAL DOOR OPENING ASSEMBLIES
08 17 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
INTEGRATED METAL DOOR OPENING ASSEMBLIES
08 17 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 31 00 - ACCESS DOORS AND FRAMES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Access panels for mechanical and plumbing access.
1.2 PRODUCTS
A. Access Doors - Mechanical and Plumbing Access:
1.
Frames: 16 gage sheet steel with flange suitable for adjacent material; 16 gage stainless
steel, AISI No. 4 satin finish with flange suitable for adjacent material in areas exposed to
moisture.
2.
Doors: 14 gage sheet steel; 14 gage stainless steel, AISI No. 4 satin finish in areas
exposed to moisture.
3.
Door Type: Flush panel.
4.
Locking Devices: Cylinder locks.
1.3 MANUFACTURERS
A. J. L. Industries, Inc.
B.
Karp Associates, Inc.
C.
Larsen's Manufacturing Company.
D. Milcor Limited Partnership.
END OF SECTION
ACCESS DOORS AND FRAMES
08 31 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ACCESS DOORS AND FRAMES
08 31 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 33 23 - OVERHEAD COILING DOORS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Overhead coiling doors, operating hardware, insulated exterior with electric operation.
1.2 PRODUCTS
A. Exterior Coiling Doors: Steel slat curtain.
1.
Capable of withstanding positive and negative wind loads of 20 psf, without
undue deflection or damage to components.
2.
Sandwich slat construction with insulated core of closed cell pressure foamed in
place urethane type insulation; R-value of 6.25 or better.
3.
Nominal Slat Size: 2 inches wide x required length.
4.
Finish: Primed steel with powder coated finish.
5.
Guides: Angles; galvanized steel.
6.
Hood Enclosure: Manufacturer's standard; primed steel with powder coated finish.
7.
Electric operation.
8.
Mounting: Surface mounted.
B. Non-Fire-Rated Interior Coiling Doors: Steel slat curtain.
1.3 MANUFACTURERS
A. Cornell Iron Works, Inc: www.cornelliron.com.
B.
The Cookson Company: www.cooksondoor.com.
C. McKeon Door Company: www.mckeondoor.com.
D. Overhead Door Corporation: www.overheaddoor.com.
END OF SECTION
OVERHEAD COILING DOORS
08 33 23 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
OVERHEAD COILING DOORS
08 33 23 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 33 26 - OVERHEAD COILING GRILLES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Interior Overhead Coiling Grilles.
1.2 PRODUCTS
A. Overhead Coiling Grilles:
1.
Grille Curtain and Finish: Aluminum, ASTM B 221; clear anodized finish.
2.
Operation: Electric grille operator.
B. Auxiliary Materials:
1.
Helical torsion spring counterbalance
2.
Hood for curtain and operating mechanism.
3.
Automatic reversing control for bottom bar for electric grille operator.
1.3 MANUFACTURERS
A. Atlas Door Corp.; Div. of Clopay Building Products Co.
B.
The Cookson Company.
C.
Cornell Iron Works, Inc.
D. Mahon Door Corp.
E.
McKeon Rolling Steel Door Company, Inc.
F.
Overhead Door Corporation.
G. Raynor Garage Doors.
H. Wayne-Dalton Corp.
I. Windsor Door; A United Dominion Company. END
OF SECTION
OVERHEAD COILING GRILLES
08 33 26 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
OVERHEAD COILING GRILLES
08 33 26 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 41 13 - ALUMINUM FRAMED ENTRANCES AND STOREFRONTS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Aluminum Entrances and Storefront:
1.
Exterior entrance doors.
2.
Storefront-type framing system.
1.2 PRODUCTS
A. Aluminum Entrances and Thermally-broken Storefront:
1.
Door Style: Wide stile and rail doors.
2.
Aluminum Members: ASTM B 221, B 209 and B 211.
3.
Steel Reinforcement: ASTM A 36, ASTM A 611, and ASTM A 570.
4.
Glass and Glazing: Insulating glass.
B. Aluminum Finish: Fluoropolymer 2-coat system; color as selected.
C. Auxiliary Materials:
1.
Push/pulls, door stops, overhead holders, and deadlocks.
2.
Weatherstripping and thresholds.
3.
Exit devices.
1.3 MANUFACTURERS
A. Vistawall Architectural Products.
B.
EFCO Corporation.
C.
Kawneer Company, Inc.
D. TRACO
E.
Tubelite Architectural Systems.
F.
YKK AP America Inc.
END OF SECTION
ALUMINUM FRAMED ENTRANCES AND STOREFRONTS
08 41 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ALUMINUM FRAMED ENTRANCES AND STOREFRONTS
08 41 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 44 13 - GLAZED ALUMINUM CURTAIN WALLS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Glazed aluminum curtain wall with interior and exterior exposed metal framing.
1.2 WARRANTY
A. Curtain Wall System Warranty: Manufacturer's 5 year warranty.
1.3 PRODUCTS
A. Glazed Aluminum Curtain Walls:
1.
Primary Components: Extruded aluminum framing, internal reinforcement, spandrel
panels, trim, and filler units, sealants, and gaskets.
2.
System: Shear block, reglazable from the exterior.
3.
Glazing: Insulating glass.
4.
Construction: Thermal-break type.
5.
Anchors, Clips, and Accessories: Aluminum, stainless steel, or galvanized steel.
6.
Aluminum Finish: Fluoropolymer 2-coat system; color as selected.
1.4 MANUFACTURERS
A. Vistawall Architectural Products.
B.
EFCO Corporation.
C.
Kawneer Company, Inc.
D. YKK AP America Inc.
END OF SECTION
GLAZED ALUMINUM CURTAIN WALLS
08 44 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
GLAZED ALUMINUM CURTAIN WALLS
08 44 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 51 13 - ALUMINUM WINDOWS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Aluminum single hung windows.
1.2 PRODUCTS
A. Aluminum Windows:
1.
Window Operation: Single-hung windows.
2.
Window Grade: AAMA Grade and Performance Class DH-HC50.
3.
Glazing: Insulating glass.
4.
Construction: Thermal-break type.
5.
Aluminum Window Members: Aluminum extrusions.
6.
Anchors, Clips, and Window Accessories: Aluminum, nonmagnetic stainless steel, or
galvanized steel.
7.
Aluminum Finish: Fluoropolymer 2-coat system; color as selected.
B. Hardware:
1.
Sash Lock: Cam-action sweep lock (2 per sash).
2.
Lift Handle: Applied sash lifts on bottom rail of lower sash (2 per sash).
1.3 MANUFACTURERS
A. TRACO
B.
EFCO Corporation.
C.
Peerless.
D. Thermal Windows, Inc.
END OF SECTION
ALUMINUM WINDOWS
08 51 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ALUMINUM WINDOWS
08 51 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 63 00 - METAL FRAMED SKYLIGHTS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Aluminum-framed skylights; field-installed pressure caps on four sides.
1.2 PRODUCTS
A. Insulating Glass: 1 inch total thickness sealed insulated units; outer pane of tinted heat
strengthened glass; inner pane of clear laminated glass, space of sealed air.
B. Fabricate aluminum components that, when assembled, have the following characteristics:
1.
Profiles that are sharp, straight, and free of defects or deformations.
2.
Accurately fitted joints with ends coped or mitered.
3.
Internal guttering systems or other means to drain water passing joints, condensation
occurring within framing members, and moisture migrating within skylight to exterior.
4.
Physical and thermal isolation of glazing from framing members.
5.
Accommodations for thermal and mechanical movements of glazing and framing
to maintain required glazing edge clearances.
C. Fabricate aluminum sill closures with weep holes and for installation as continuous
component.
D. Aluminum Finish: Fluoropolymer 2-coat system; color as selected.
1.3 MANUFACTURERS
A. Architectural Skylight Company, Inc.
B.
Fisher Skylights, Inc.
C.
LinEl Signature.
D. Naturalite Skylight Systems.
END OF SECTION
METAL FRAMED SKYLIGHTS
08 63 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
METAL FRAMED SKYLIGHTS
08 63 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 71 00 - DOOR HARDWARE
PROJECT INCLUDES
1.1 SECTION SUMMARY A.
Hardware for doors.
1.2 QUALITY ASSURANCE
A. Hardware for Fire-Rated Openings: NFPA 80, and local requirements.
B.
Handicapped Accessibility: ANSI A117.1, and local requirements.
C.
Materials and Application: ANSI A156 series standards.
1.3 PRODUCTS
A. Door
1.
2.
3.
4.
5.
6.
7.
8.
Hardware:
Quality Level: Heavy duty commercial type.
Locksets and Latchsets: Cylinder and mortise type.
Lock Cylinders: Interchangeable type.
Keying: Owner's requirements keying and key control system.
Hinges and Butts: Full-mortise type with nonremovable pins at exterior doors.
Closers, Door Control, and Exit Devices: Barrier-free type.
Pivots: Offset or center-hung type.
Push/Pull Units: Through-bolted type.
B. Hardware Finishes: Satin chrome and satin stainless finishes on exposed surfaces.
C. Auxiliary Materials:
1.
Door trim units.
2.
Kickplates.
3.
Stops and overhead door holders.
4.
Weatherstripping and thresholds.
5.
Hinges: Hager, McKinney, Stanley.
6.
Electromagnetic hold-open devices.
1.4 MANUFACTURERS
A. Hinges: Hager, McKinney, Stanley.
B. Locksets and Latchsets:
1.
Corbin Russwin - CL3400 - Newport
2.
Sargent 10-Line-LL
3.
Best 9-K Series - Trim 15L.
C. Closers: LCN, Sargent.
D. Panic Devices: Von Duprin 98-Series as listed in HW sets, Yale 7100 series, Corbin/Russwin
ED5000 series, or Sargent 80 series.
E. Protective Plates: Lindstrom, Rockwood, Ives.
F. Thresholds, Weatherstipping, and Gasketing: Zero, National Guard Products, Pemko.
1.5 Handicapped Swing Door Operator
A. Low Energy Power Operated Door operating equipment (Sr-Swing) shall be fabricated by
Dor-O-Matic, Chicago, IL 60656, Phone: 800/543-4635, Fax: 708-867-0310.
DOOR HARDWARE
08 71 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
B. System Operation:
1.
Handicap Mode: In the handicap mode, one of the push buttons on either side of the door
is actuated and the door opens slowly - to back check (80 degrees) in 3 to 6 seconds and
to the fully open position in 4 to 7 seconds. The door will then remain open for a period
of 5 to 30 seconds as determined by the setting the customer puts into the variable time
delay on the control box. After the time delay, the door closes by the spring in the door
operator from 90 degrees to 10 degrees in 3 to 6 seconds and from 10 degrees to fully
closed in 1-1/2 to 2 seconds.
2.
Push-N-Go Mode: In the Push-N-Go mode, pedestrian traffic walks up to the door and
begins to push or pull open the door. When the door is open approximately 5 degrees, the
control box takes over and continues to open the door - slowly and automatically to the
full open position. When the door is opened as a result of Push-N-Go the door will stay
fully open less than a second and then close - just like a manual door.
3.
Manual Mode: In the manual mode, the actuation switches and the Push-N-Go feature
will be deactivated and the operator shall function in the same manner as a common
manual closer.
END OF SECTION
DOOR HARDWARE
08 71 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 80 00 - GLAZING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Glass and Glazing:
1.
Exterior windows.
2.
Exterior entrances and storefront.
3.
Interior doors and glazed openings.
1.2 WARRANTY
A. Glass Warranties:
1. Insulating Glass: Manufacturers 10 year warranty.
1.3 PRODUCTS
A. Glass:
1.
Primary Glass Products: Clear float and wire glass, ASTM C 1036.
2.
Heat-Treated Glass Products: Heat-strengthened, tempered, coated, and spandrel glass,
ASTM C 1048.
3.
Laminated Glass Units: Polyvinyl butyral interlayer.
4.
Sealed Insulating Glass Units: Argon filled, ASTM E 774, Class A.
5.
High-Performance Coatings: Low e (low emissivity) type.
B. Glazing:
1.
Elastomeric glazing sealants.
2.
Preformed glazing tapes.
3.
Glazing gaskets.
4.
Setting blocks, spacers, and compressible filler rods.
1.4 SCHEDULE
A. Glazing Schedule:
1.
Exterior Glazed Openings: 1-inch thick, Hermetic Dry Air filled, Low-e insulating
unit, tinted glass.
2.
Interior Doors and Glazed Openings: 1/4-inch tempered.
1.5 MANUFACTURERS
A. Glass
1.
2.
3.
4.
5.
Products:
AFG Industries Inc.
Guardian Industries Corp.
Oldcastle Glass Group.
Pilkington Building Products of North America.
PPG Industries, Inc.
END OF SECTION
GLAZING
08 80 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
GLAZING
08 80 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 83 00 - MIRRORS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Film-backed silvered flat glass mirrors qualifying as safety glazing.
1.2 PRODUCTS
A. Clear Glass Mirrors: ASTM C 1503, Mirror Select Quality.
B.
Nominal Thickness: 6.0 mm.
C.
Edge Sealer: Coating compatible with glass coating and approved by mirror manufacturer for
use in protecting against silver deterioration at mirrored glass edges.
D. Mirror Mastic: An adhesive setting compound, produced specifically for setting mirrors and
certified by both mirror manufacturer and mastic manufacturer as compatible with glass
coating and substrates on which mirrors will be installed.
E.
Top and Bottom Aluminum J-Channels: Aluminum extrusions with a return deep enough to
produce a glazing channel to accommodate mirrors of thickness indicated and in lengths
required to cover bottom and top edges of each mirror in a single piece.
1.3 FABRICATION
A. Film-Backed Safety Mirrors: Apply film backing with pressure-sensitive adhesive coating over
mirror backing paint as recommended in writing by film-backing manufacturer to produce a
surface free of bubbles, blisters, and other imperfections. Use adhesives and film backing
compatible with mirror backing paint as certified by mirror manufacturer.
MIRRORS
08 83 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
MIRRORS
08 83 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 08 90 00 - LOUVERS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Fixed metal wall louvers.
1.2 PRODUCTS
A. Aluminum Louvers:
1.
Aluminum Extrusions: ASTM B 221, alloy 6063-T5 or T52.
2.
Blade Type: Storm resistant design of horizontal and vertical blades.
3.
Depth: 7 inches.
4.
Finish: Fluoropolymer, Kynar 500.
B. Louver Accessories:
1. Bird screens.
1.3 MANUFACTURES
A. Airline Products Co.
B.
Airolite Co.
C.
Construction Specialties, Inc.
D. Industrial Louvers, Inc.
E. Ruskin Manufacturing; Tomkins Industries, Inc.
END OF SECTION
LOUVERS
08 90 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
LOUVERS
08 90 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 21 16 - GYPSUM BOARD ASSEMBLIES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Gypsum Drywall Systems:
1. Interior walls, partitions, and ceilings for tape and joint compound finish.
2. Insulation and vapor barrier systems in gypsum drywall systems.
3. Shaftwall System.
4. Exterior Gypsum Sheathing.
5. Abuse-Resistant Interior Panels.
B. Gypsum Drywall Attachment:
1. Gypsum board screw-attached.
2. Joint treatment and accessories.
1.2 PRODUCTS
A. Gypsum Board:
1. Gypsum Wallboard: ASTM C 36, regular, foil-backed, and fire-rated types, 5/8-inch
typical thicknesses.
2. Sag-Resistant Gypsum Wallboard: ASTM C 1396, manufactured to have more sag
resistance than regular-type gypsum board.
a. Thickness: 5/8 inch.
b. Long Edges: Tapered.
c. Location: Ceiling surfaces.
3. Moisture and Mold Resistant Wallboard:
a. Location: High-humidity or wet locations, wallboard installed at building perimeter,
and any wallboard furred to concrete or masonry construction; walls or ceilings. 1)
High-humidity or wet locations include areas with showers, janitor basins, gang
toilets and mechanical spaces with steam, hot water or condensation generating
equipment.
b. Basis-of-Design: DensArmor by G-P Gypsum.
c. Characteristics:
1)
Coated inorganic glass mat-faced, water-resistant, treated core
gypsum wallboard.
2)
Physical properties conforming to the applicable sections of ASTM C 1177
and ASTM C 630.
3)
Resists the growth of mold when tested, as manufactured, according to
ASTM D 3273.
4)
Acceptable Products:
(a) SHEETROCK® Brand HUMITEK® Gypsum Panels by USG.
(b) Gold Bond® BRAND XP® Wallboard by National Gypsum.Mold
Defense Products by LaFarge.Provide Type X panels where required.
4. Joint Treatment: ASTM C 475 and ASTM C 840, 3-coat system.
5. Installation Standard: ASTM C 840.
B. Shaft Walls at HVAC Shafts: Provide completed assemblies with the following
characteristics:
1. Air Pressure Within Shaft: Sustained loads of 5 lbf/sq ft with maximum mid-span
deflection of L/240.
GYPSUM BOARD ASSEMBLIES
09 21 16 - 1
Grimm + Parker Architects Project No. 21145.00
2.
3.
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
Acoustic Attenuation: STC of 35-39 calculated in accordance with ASTM E 413, based
on tests conducted in accordance with ASTM E 90.
Basis-of-Design: Dens-Glass Ultra Shaft Guard by G-P Gypsum. a.
Contractor Option: The contractor may provide the following instead of
Basis-of-Design Product.
1) Fire-Shield Shaftliner XP panels by National Gypsum.
2) Sheetrock Brand Gypsum Liner Panels Mold Tough by USG.
C. Exterior Sheathing:
1.
Basis-of-Design: Dens-Glass Gold Exterior Guard by G-P Gypsum; Type X.
2.
Other Available Product: CertainTeed GlasRoc Brand Sheathing; Type X.
D. Abuse-Resistant Interior Panels: 48 inches AFF in all corridors and public spaces.
1. Basis-of-Design: Fiberock VHI Abuse-Resistant Interior Panels by USG, fire rated.
E. Trim Accessories:
1.
Corners: Preformed structural outside and inside corners comprised of tapered plastic
center membrane or metal, with prefinished paper surface and paper flap; provide
No-Coat Prefinished Corners manufactured by Grabber Construction Products, or
Sheetrock Paper Faced Metal Drywall Bead and Trim manufactured by United States
Gypsum Company.
2.
Expansion (Control) Joints: One-piece control joint formed with V-shaped slot.
F. Auxiliary Materials:
1.
Gypsum board screws, ASTM C 1002.
2.
Fastening adhesive.
3.
Concealed acoustical sealant.
4.
Mineral fiber sound attenuation blankets.
1.3 MANUFACTURERS
A. Gypsum Board and Related Products:
1.
Georgia-Pacific Corp.
2.
National Gypsum Co.; Gold Bond Building Products Division.
3.
United States Gypsum Co.
END OF SECTION
GYPSUM BOARD ASSEMBLIES
09 21 16 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 22 16 - NON LOAD-BEARING STEEL FRAMING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Non-load-bearing steel framing members for the following applications:
1. Interior framing systems (e.g. supports for partition walls, framed soffits, furring, etc.)
2. Interior suspension system (e.g. supports for ceiling, suspended soffits, etc).
1.2 QUALITY ASSURANCE
A. Fire-Test-Response Characteristics: For fire-resistance-rated assemblies that incorporate nonload bearing steel framing, provide materials and construction identical to those tested in
assembly indicated accordingly to ASTM E 119 by an independent testing agency.
B.
Framing Members, General: Comply with ASTM C 754 for conditions indicated.
1.3 PRODUCTS
A. Steel Sheet Components: Comply with ASTM C645 requirements for metal, unless
otherwise indicated.
B. Protective Coating: [ASTM A 641, Class 1 zinc coating, soft temper, 0.0625 inch diameter
wire, or double strand of 0.0475 inch diameter wire.
C. Suspension System Components:
1. Tie Wire: ASTM A641, Class 1 zinc coating, soft temper, 0.0625 inch diameter wire, or
double strand of 0.0475 inch diameter wire.
2. Wire Hangers: ASTM A641, Class 1 zinc coating, soft temper, 0.162-inch diameter.
3. Carrying Channels: Cold-rolled, commercial-steel sheet with a base metal thickness of
0.0538 inch and minimum V2 inch wide flanges.
D. Furring Channels (Furring Members)
1. Cold-Rolled Channels: 0.0538 inch bare-steel thickness, with minimum V2 inch
wide flanges, 3/4 inch deep.
2. Steel Studs: ASTM C645
3. Hat-Shaped, Rigid Furring Channels: ASTM C645, 7/8 inch deep; 0-.0179 inch.
4. Z-Shaped Furring: With slotted or non-slotted web, face flange of 1 1 1/4 inches, wall
attachment flange of 7/8 inch, minimum bare-metal thickness of 0.0179 inch, and
depth required to fit insulation thickness indicated.
5. Resilient Furring Channels: V2 inch deep members designed to reduce sounds
transmission.
E. Grid Suspension System for Ceilings: ASTM C645, direct hung system composed of main
beams and cross-furring members that interlock.
1. Products: Subject to compliance with requirements, provide one of the following:
a. Armstrong World Industries Inc. Drywall Grid System
b. Chicago Metallic Corporation: Drywall Furring System
c. USG Corporation: Drywall Suspension System
F. Deflection Track: Steel sheet top runner manufactured to prevent cracking of finishes applied
to interior partition framing resulting from deflection of structure above; in thickness
not
less than indicated for studs and in width to accommodate depth of studs.
1. Products: Suject to compliance with requirements, provide one of the following: a.
Steel Network, Inc. (The): VeriTrack VTD Series
NON LOAD-BEARING STEEL FRAMING
09 22 16 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
b. Superior Metal Trim: Superior Flex Track System (SFT)
G. Firestop Tracks: Top runner manufactured to allow partition heads to expand and contract
with movement of the structure while maintaining continuity of fire-resistance-rated
assembly indicated; in thickness not less than indicated for studs and in width to
accommodate depth of studs.
1. Products: Subject to compliance with requirements, provide one of the following:
a. Fire Trak Corp; Fire Trak
b. Metal-Lite, Inc.; The System
END OF SECTION
NON LOAD-BEARING STEEL FRAMING
09 22 16 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 30 00 - TILING
PROJECT INCLUDES
1.1 SECTION SUMMARY:
A. Interior Tile:
1.
Unglazed porcelain floor and wall tile.
2.
Unglazed quarry tile.
3.
Stone thresholds installed as part of tile installations.
4.
Crack-suppression membrane for thin-set tile installations.
5.
Metal edge strips installed as part of tile installations.
1.2 QUALITY ASSURANCE
A. Tile Materials: ANSI 118 series standard specifications.
B.
Tile Installation: ANSI 108 series standard specifications and Tile Council of America,
Handbook for Ceramic Tile Installation.
1.3 PRODUCTS
A. Unglazed Porcelain Floor and Wall Tile:
1.
Type: Porcelain factory-mounted flat tile.
2.
Size: 12 by 24 inches.
3.
Thickness: 5/16 inch nominal.
4.
Face: Plain face with cushion edges.
B. Unglazed Quarry Tile:
1.
Type: Nonabrasive square-edged flat tile.
2.
Size: 8 by 8 inches.
3.
Thickness: 1/2 inch nominal.
4.
Face: Plain face.
C. Tile Accessories:
1.
Matching trim units.
2.
Marble thresholds.
D. Setting Materials:
1. Latex-Portland cement mortar, ANSI A118.4.
E. Grout:
1.
Latex-Portland cement grout, ANSI A118.6.
2.
Chemical-resistant epoxy grout, ANSI A118.3 (Quarry tile).
F. Setting Accessories:
1.
Membrane waterproofing under tile.
2.
Cementitious tile backer board.
G. Elastomeric Sealants:
1.
One-part mildew-resistant silicone sealant for non-traffic areas.
2.
Multi-part pourable urethane sealant for traffic areas.
H. Metal Edge Strips:
1. Open Edge of Tile with Adjacent Finish of Similar Height:
a. General: Angle or L-shape, height to match tile and setting-bed thickness, metallic or
combination of metal and PVC or neoprene base, designed specifically for
TILING
09 30 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
flooring applications, stainless steel; ASTM A 666, 300 Series exposed-edge
material.
b. Basis-of-Design: 1.1 Schluter-SCHIENE Edge-protecting Profile; stainless steel.
2. Open Edge of Tile with Adjacent Finish of Different Height:
a. General: ADA-compliant profile, height to match tile and setting-bed thickness,
metallic or combination of metal and PVC or neoprene base, designed specifically
for flooring applications, stainless steel; ASTM A 666, 300 Series exposed-edge
material.
b. Basis-of-Design:
1)
1.2 Schluter-RENO-U Reducer Profile, where tile surface is higher
than adjacent finish; stainless steel.
2)
1.5 Schluter-RENO-UK Sloped Transition Profile, where tile surface is
lower than adjacent finish; stainless steel.
1.4 SCHEDULE
A. As indicated on Finish Schedule for specific locations.
1.5 MANUFACTURERS
A. Tile Products:
1.
American Olean.
2.
Buchtal Corporation USA.
3.
Crossville Ceramics.
4.
Daltile Corp.
5.
Florida Tile Industries, Inc.
6.
Summitville Tiles, Inc.
B. Mortars and Grouts:
1.
Custom Building Products.
2.
Laticrete International, Inc.
3.
Mapei Corporation.
4.
Bonsal: W.R. Bonsal Company.
5.
Bostik.
6.
TEC Incorporated.
END OF SECTION
TILING
09 30 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 51 00 - ACOUSTICAL TILE CEILINGS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Interior Acoustical lay-in panel ceilings, trim, and exposed metal suspension system.
1.2 QUALITY ASSURANCE
A. Performance: Fire, structural, and performance meeting requirements of building code and
local authorities.
1.3 WARRANTY
A. Sag-Resistance Warranty: 10 year warranty against sag of ceiling panels and rusting of grid.
1.4 PRODUCTS
A. Interior Mineral Base Panels, Water Felted:
1.
Type, Form, and Finish: ASTM E1264, Type IV, Form 2 with painted finish.
2.
Thickness: 3/4 inch.
3.
Composition: Mineral.
4.
Light Reflectance: 0.90 or better; ASTM E1477.
5.
NRC Range: 0.70 or better; ASTM C423.
6.
Edge: Beveled regular.
7.
Surface Color: White.
8.
Surface Finish: Non-directional fine texture.
9.
Shall withstand combined effects of temperatures to 104 degrees F and relative
humidity to 90 percent without visible sag.
10. Ten-year warranty for sag resistance.
B. Direct-Hung Suspension Systems, Non-Fire-Resistance Rated:
1.
Type: Narrow-Face, Uncapped, Double-Web, Steel Suspension System: Main and cross
runners roll formed from cold-rolled steel sheet, prepainted, hot-dip galvanized, to
produce structural members with 9/16-inch- wide faces.
a. Face Design: With 1/8-inch- wide, slotted, box-shaped flange.
2.
Suspension System Accessories: Attachment devices and hangers.
C. Extruded Perimeter Trim:
1. Location:
a. Edge trim system for transitions between drywall and suspended ceilings.
b. Boundary trim system for isolated hung areas of suspended ceilings.
2. Components:
a. Extruded aluminum alloy 6063 trim channel.
b. Attachment to grid system is provided by tee-bar connection clips which lock
into bosses on the trim channel and are screw-attached to the web of the
intersecting suspension system members.
c. Sections of trim are joined together using the splice plate.
1.5 MANUFACTURERS
A. Mineral Base Panels, Water Felted:
B.
Armstrong World Industries, Inc., Ultima Beveled Tegular Item #1912, Fine Fissured,
No. 1729.
ACOUSTICAL TILE CEILINGS
09 51 00 - 1
Grimm + Parker Architects Project No. 21145.00
C.
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
USG Interiors, Inc., Mars ClimaPlus, Radar Clima Plus, No. 2410.
D. The Celotex Corporation, Vantage 10, No. VAN-197.
E.
Steel Suspension System: Wide-face, capped double web galvanized steel, intermediate duty
classification, hot dipped galvanized, ASTM C 635.
END OF SECTION
ACOUSTICAL TILE CEILINGS
09 51 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 52 50 - INTERACTIVE ACOUSTICAL PANEL SYSTEM
PROJECT INCLUDES
1.1 SECTION SUMMARY:
A. Interactive acoustical ceiling and wall panels.
1.2 PRODUCTS
A. Absorber Panels: 6 lb./cu. ft. fiberglass board with foil backing (no exposed fiberglass) , metal
edged frames, covered with Class A rated fabric according to ASTM E-84. Corner brackets are
integrated into the metal edged frame and receive mounting hardware.
B.
C.
Ceiling and Type I Wall Diffusers: Thermo-molded plastic, 0.125-inch material thickness.
Type II Wall Diffusers: Thermo-molded plastic, 0.125-inch material thickness, with glass fiber
board glued to concave rear surface of wall panels greater than or equal to 24 sq ft.
D. Mounting Hardware: Manufacturer's standard.
1.3 FINISHES
A. Wall-mounted Panels: Manufacturer's standard woven plain weave 100 percent polyester 2-ply
fabric wrapping entire core and frame and glued to back of frame; colors as selected from
manufacturer's standard range.
B.
Ceiling-mounted Panels: Manufacturer's standard white, "orange peel" texture.
C.
Ceiling-mounted Absorber Panels: Manufacturer's standard woven plain weave 100 percent
polyester 2-ply fabric wrapping entire core and frame and glued to back of frame; colors as
selected from manufacturer's standard range.
1.4 MANUFACTURERS
A. Interactive Acoustical Panel System; Wenger Corporation.
B. Customline Diffusers; Wall Technology, Inc.
C. Repond Wall and Ceiling Diffusers; Conwed. END
OF SECTION
INTERACTIVE ACOUSTICAL PANEL SYSTEM
09 52 50 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
INTERACTIVE ACOUSTICAL PANEL SYSTEM
09 52 50 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 54 50 - FRP CEILING SYSTEM
PROJECT INCLUDES
1.1 SECTION SUMMARY:
A. Fiberglass reinforced ceiling panels in fiberglass reinforce ceiling grid.
1.2 PRODUCTS
A. Fiberglass Reinforced Plastic Panels: USDA approved.
1.
Size: 24 x 48 inches.
2.
Nominal Thickness: 0.12 inches.
3.
Wide-Face Fiberglass Suspension System: Fiberglass reinforced plastic;
intermediate-duty classification:
4.
Face Design: Flush face.
5.
Manufacturer: Sanigrid; Kemlite Company.
1.3 MANUFACTURERS
A. Glasbord FXI with Surfseal; Kemlite Company.
B.
DynaGlass; Chicago Metallic.
END OF SECTION
FRP CEILING SYSTEM
09 54 50 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
FRP CEILING SYSTEM
09 54 50 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 64 66 - WOOD ATHLETIC FLOORING
PROJECT INCLUDES
1.1 SECTION SUMMARY:
A. Wood Athletic Flooring.
1.2 PRODUCTS
A. Wood Strip Flooring for Athletic Application:
1.
Type: Mixed-grain first grade, northern hard maple wood strip flooring, 25/32 inch thick,
2-1/4 inch face width.
2.
Installation System: [Floating, cushioned subflooring system.] [Resilient sleeper
subflooring system.]
3.
Finish: High-build gym floor finish and game markings.
B. Auxiliary Materials:
1.
Moisture Barrier: 6 mil polyethylene sheeting.
2.
Trim, moldings, and reducer strips.
3.
Underlayments, mounts, adhesives, mastics, and fasteners.
1.3 MANUFACTURERS
A. Connor Sports Flooring Corp.; DuraCushion III.
B.
Aacer Flooring, LLC; AacerCush I.
C. Action Floor Systems, LLC; ActionCush II
D. Horner Flooring Company; Thrust-A-Cushion Sleeper.
END OF SECTION
WOOD ATHLETIC FLOORING
09 64 66 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
WOOD ATHLETIC FLOORING
09 64 66 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 65 00 - RESILIENT FLOORING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Resilient flooring and floor preparation.
B.
Resilient wall base and accessories.
C.
Resilient stair accessories.
1.2 PRODUCTS
A. Tile Flooring:
1.
Vinyl Composition Tile: ASTM F 1066, Composition 1, nonasbestos formulated, Class
1 (solid color tile) and Class 2 (through pattern tile), 12 x 12 inches; 1/8 inch thick. a.
Colors and Patterns: As selected by Architect from manufacturer's full range. A
maximum of 12 colors will be selected; 75 percent standard colors and 25 percent
premium colors.
2.
Rubber Floor Tile (Stair Landings): ASTM F 1344.
3.
Resilient Terrazzo Tile:
a. Type: Polyester resin marble chip flooring.
b. Nominal Facial Dimensions: 11-31/32" x 11-31/32"Nominal Thickness: 1/8 inch.
c. Face: Plain square edged.
d. Basis-of-Design: "Fritztile Classic Series” manufactured by Fritztile, Div. of Fritz
Industries, Inc.
B. Sheet Linoleum: Homogeneous sheet linoleum, with color and pattern throughout entire sheet,
consisting of linseed oil, wood flour, and rosin binders, mixed and calendered onto natural jute
backing.
C. Rubber Wall Base: ASTM F 1861, TS (rubber, vulcanized thermoset), Group 1 (solid), 4-inch
height, 1/8 inch thick.
D. Stair Treads: Rubber; full width and depth of stair tread in one piece; tapered thickness;
nosing not less than 1-5/8 inch deep.
1.
Minimum Requirements: Comply with FS RR-T-650 requirements corresponding to
type specified.
2.
Critical Radiant Flux (CRF): Minimum 0.45 watt per square centimeter, when tested in
accordance with ASTM E 648 or NFPA 253.Nominal Thickness: 0.1875 inch.
3.
Nosing: Square.
4.
Style: Combined tread and riser; molded disc pattern tread with contrasting color
abrasive grit strips full width at nosing.
5.
Color: Solid.
E. Auxiliary Materials:
1. Edge strips and terminations.
1.3 MANUFACTURERS
A. Vinyl Composition Floor Tile:
1.
Armstrong World Industries, Inc.
2.
Azrock Industries, Inc.
3.
Congoleum Corporation.
4.
Mannington Mills, Inc.
RESILIENT FLOORING
09 65 00 - 1
Grimm + Parker Architects Project No. 21145.00
5.
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
Tarkett, Inc.
B. Rubber Floor Tile:
1. Basis-of-Design: Noraplan Environcare by Freudenberg Building Systems, Inc.
C. Linoleum:
1.
Forbo Industries.
2.
Azrock Commercial Flooring.
D. Resilient Base and Stair Accessories:
1.
Burke Mercer Flooring Products.
2.
Nora Rubber Flooring; Freudenberg Building Systems, Inc.
3.
Roppe Corporation.
END OF SECTION
RESILIENT FLOORING
09 65 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 68 00 - CARPETING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Carpet and floor preparation.
1.2 PRODUCTS
A. Carpet Material:
1.
Fiber Content: Type 6,6 nylon; yarn dyed.
2.
Face Construction: Tufted textured loop.
3.
Surface Pile Weight: [26 oz./sq. yd.]
4.
Minimum Density Factor: 6,455; weight density 164,424.
5.
Primary Backing: Woven polypropylene.
6.
Bonding Agent: Unibond by Lees Carpet or equal.
7.
Width: 12 feet
8.
Critical Radiant Flux Classification: Class I, not less than 0.45 W/sq. cm per ASTM E
648.
9.
Tuft Bind: Not less than 20 lbf per ASTM D 1335.
10. Static Resistance: Not less than 500,000 ohms, nor more than 20,000 megohms,
measured according to the test method for conductive flooring specified in Chapter 12
of NFPA 99.
11. Static Generation: Less than 1.8 kv at 20 percent relative humidity, per AATCC-134
using step and scuff tests with neolite and chrome-tanned leather soles.
12. Antimicrobial Activity: Not less than 2-mm halo of inhibition for gram-positive bacteria;
not less than 1-mm halo of inhibition for gram-negative bacteria; no fungal growth; per
AATCC-174.
B. Auxiliary Materials:
1.
Edge guards.
2.
Adhesives and cements.
C. Carpet Installation Method:
1.
Installation is directly glued down for corridors, public spaces and handicapped units.
2.
Installation is applied over padding.
1.3 MANUFACTURERS
A. Project Standard: [Faculty IV by Lees Commercial Carpets, a division of Burlington
Industries.] [Bigelow Commercial.] [Bentley Prince Street.] [Shaw Commercial.]
END OF SECTION
CARPETING
09 68 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
CARPETING
09 68 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 84 00 - ACOUSTICAL ROOM
COMPONENTS PROJECT INCLUDES
1.1 SECTION SUMMARY: A.
Acoustical wall panels.
1.2 PRODUCTS
A. Back-Mounted Edge-Reinforced Acoustical Wall Panels:
1.
Core: Standard face panels.
2.
Facing Material: Woven polyester or polyethylene.
3.
Panel Edge Detail: Beveled edge.
4.
Noise Reduction Coefficient: 0.80 NRC.
B. Wall Attached Cementitions Wood Fiberboard.
C. Auxiliary Materials:
1. Clips and hangers.
1.3 MANUFACTURERS
A. Back-Mounted Edge Reinforced Acoustical Wall Panels:
1.
Respond ACT; Conwed.
2.
Panel Type AP; Decoustics.
3.
Panel Type A100; Wall Technology, Inc.
B. Wood Fiberboard:
1. Tectum, Inc.
END OF SECTION
ACOUSTICAL ROOM COMPONENTS
09 84 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ACOUSTICAL ROOM COMPONENTS
09 84 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 91 13 - EXTERIOR PAINTING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Painting and surface preparation for exterior unfinished surfaces as scheduled.
1.2 QUALITY ASSURANCE
A. Regulations: Compliance with Low/No VOC and environmental regulations.
1.3 EXTERIOR PAINT SCHEDULE
A. Exterior Gypsum Board to Receive Flat Acylic Finish: 1coat alkyd or alkali-resistant primer, 2
coats flat exterior acrylic-emulsion paint.
B.
Zinc Coated Metal to Receive Silicone-Alkyd Enamel Finish: 1 coat galvanized metal primer,
2 coats silicone-alkyd enamel.
1.4 MANUFACTURERS
A. Duron Paints and Wallcoverings.
B.
ICI Paint Stores, Inc.
C.
McCormick Paints.
D. Benjamin Moore & Co.
E.
PPG Industries, Inc.
F.
Sherwin-Williams Co.
END OF SECTION
EXTERIOR PAINTING
09 91 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
EXTERIOR PAINTING
09 91 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 91 23 - INTERIOR PAINTING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Painting and surface preparation for interior unfinished surfaces as scheduled.
B.
Field-painting and surface preparation of exposed mechanical and electrical piping, conduit,
ductwork, and equipment.
1.2 QUALITY ASSURANCE
A. Regulations: Compliance with Low/No VOC and environmental regulations.
1.3 INTERIOR PAINT SCHEDULE
A. Concrete Masonry Units to Receive Low-Luster Acrylic-Enamel Finish: 2 coats
high-performance latex block filler, 2 coats low-luster (eggshell or satin) acrylic-latex interior
enamel.
B.
Gypsum Drywall to Receive Low-Luster Acrylic-Enamel Finish: 1 coat latex-based interior
primer, 2 coats low-luster (eggshell or satin) acrylic-latex interior enamel.
C.
Woodwork to Receive Semigloss Enamel Finish: 1 coat interior enamel undercoat, 2 coats
interior semigloss acrylic-latex enamel.
D. Stained Woodwork to Receive Stained Satin Varnish Finish: 1 paste-wood filler coat if
required, 1 coat clear sanding sealer, 1 coat waterborne interior wood stain, 2 coats waterborne
polyurethane.
E.
Natural Finish Woodwork to Receive Satin Varnish Finish: 1 paste-wood filler coat if
required, 1 coat clear sanding sealer, 2 coats waterborne polyurethane.
F.
Ferrous Metal to Receive Semigloss Enamel Finish: 1 coat rust-inhibiting primer, 1 coat
interior enamel undercoat, 1 coat interior semigloss acrylic-latex enamel.
G. Zinc Coated Metal to Receive Semigloss Finish: 1 coat galvanized metal primer, 1 coat
interior enamel undercoat, 1 coat interior semigloss acrylic-latex enamel.
1.4 MANUFACTURERS
A. Duron Paints and Wallcoverings.
B.
ICI Paint Stores, Inc.
C.
McCormick Paints.
D. Benjamin Moore & Co.
E.
PPG Industries, Inc.
F.
Sherwin-Williams Co.
END OF SECTION
INTERIOR PAINTING
09 91 23 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
INTERIOR PAINTING
09 91 23 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 93 00 - WOOD STAINS AND TRANSPARENT FINISHES
PROJECT INCLUDES
1.1 SECTION SUMMARY:
A. Transparent wood finishes.
1.2 FINISH SCHEDULE
A. Polyurethane varnish over stain system:
1.
Penetrating semi-transparent stain.
2.
Two finish coats of interior waterborne polyurethane; satin finish.
1.3 MANUFACTURERS
A. ICI Paints.
B.
International Protective Coatings.
C.
Benjamin Moore & Co.
D. Pittsburgh Paint.
E.
Sherwin Williams; Industrial and Marine Coatings.
F.
Duron Paint and Wallcoverings.
END OF SECTION
WOOD STAINS AND TRANSPARENT FINISHES
09 93 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
WOOD STAINS AND TRANSPARENT FINISHES
09 93 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 09 96 00 - HIGH-PERFORMANCE COATINGS
PROJECT INCLUDES
1.1 SECTION SUMMARY:
A. High-performance special coatings.
1.2 QUALITY ASSURANCE
A. Regulations: Compliance with VOC and environmental regulations.
1.3 INTERIOR HIGH-PERFORMANCE COATING SCHEDULE
A. Concrete Masonry Units: High-gloss acrylic epoxy enamel coating system, consisting of block
filler, intermediate coat and topcoat.
B.
Exposed Steel Structure: Polysiloxane finish over two coats of high solids epoxy primer.
C.
Gypsum Wallboard: High-gloss acrylic epoxy enamel coating system, consisting of acrylic or
alkyd primer, intermediate coat and topcoat.
1.4 MANUFACTURERS
A. ICI Paints.
B.
International Protective Coatings.
C.
Benjamin Moore & Co.
D. Pittsburgh Paint.
E.
Sherwin Williams; Industrial and Marine Coatings.
F.
Duron Paint and Wallcoverings
END OF SECTION
HIGH-PERFORMANCE COATINGS
09 96 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
HIGH-PERFORMANCE COATINGS
09 96 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 11 01 - VISUAL DISPLAY SURFACES
PROJECT INCLUDES
1.1 SECTION SUMMARY: A.
Visual display boards.
1.2 PRODUCTS
A. Markerboards:
1.
Materials: Porcelain enamel face for liquid-type markers, core material, and backing.
2.
Trim: Metal frame and tray, anodized finish.
B. Tackboards:
1.
Materials: [Vinyl-fabric-faced.] [Natural cork.]
2.
Trim: Metal frame and tray, anodized finish.
C. [Operable Units:] [Horizontal sliding.] [Vertical sliding.] [Hinged conference units.]
1.3 MANUFACTURERS:
A. Claridge Products and Equipment, Inc.
B.
Nelson Adams Company.
C.
Polyvision Corporation.
END OF SECTION
VISUAL DISPLAY SURFACES
10 11 01 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
VISUAL DISPLAY SURFACES
10 11 01 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 14 00 - SIGNAGE
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Room Signs
B.
Dimensional Letters and Numbers
C.
Cast Plaques
1.2 PRODUCTS
A. Room
1.
2.
3.
Signs:
Type: Unframed.
Material: Cast acrylic sheet.
Copy: Raised lettering.
B. Dimensional Letters and Numbers:
1.
Type: Cast.
2.
Material: Aluminum.
3.
Finish: Clear anodized or baked enamel.
C. Cast Plaques:
1. Material: Bronze castings.
1.3 MANUFACTURERS
A. Gemini Inc.
B.
Poblocki & Sons.
C.
Signs and Wonders, Inc.
D. The Supersine Company.
END OF SECTION
SIGNAGE
10 14 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SIGNAGE
10 14 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 21 13 - TOILET COMPARTMENTS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Toilet compartments and screens.
1.2 PRODUCTS
A. Type
1.
2.
3.
and Mounting:
Compartments: Floor-anchored, overhead braced.
Screens: Wall-anchored.
Style: Standard privacy style.
B. Toilet Compartment Materials:
1. [Solid Plastic, polymer resin.] [Stainless Steel: ASTM A 666, Type 304, with No. 4
polished finish.]
1.3 MANUFACTURERS:
A. Bradley.
B.
Ampco Products, Inc.
C.
General Partitions Mfg. Corp.
D. Global Steel Products Corp.
E.
Metpar Corp.
F.
Mills Partitions; Bradley Corporation.
G. Weis-Robart Partitions, Inc.
TOILET COMPARTMENTS
10 21 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
TOILET COMPARTMENTS
10 21 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 21 23 - CUBICLE CURTAINS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Health Room cubicle curtains.
1.2 PRODUCTS
A. Curtain Fabric: 100 percent trevira polyester yarn; flame-resistant.
B.
Track: Surface-mounted extruded anodized aluminum channel track.
C.
Carriers: Nickel plated brass axle with nylon wheels and nickel plated steel ball chain and
hook.
1.3 MANUFACTURERS
A. A.R. Nelson Co.
B.
General Cubicle Co., Inc.
C.
Imperial Fastener Company, Inc.
D. Kirsh, Cooper Industries, Inc.
E.
Salisbury Industries.
END OF SECTION
CUBICLE CURTAINS
10 21 23 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
CUBICLE CURTAINS
10 21 23 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 22 26 - OPERABLE PARTITIONS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Overhead track suspended operable panel partitions.
1.2 QUALITY ASSURANCE
A. System Performance:
1.
Sound Transmission Class: 50, ASTM E 413.
2.
Fire Rating: Not required.
1.3 PRODUCTS
A. Panel Types: [Paired panels, center stacked.] [Continuously hinged panels, center
stacked.]Operation: [Manual.] [Electrical operator.].
B.
Frame: Steel with steel face.
C.
Finish: [Non-woven needle-punched wall carpet.] [Vinyl-coated fabric wall covering.]
D. Accessories: [Porcelain steel markerboard and tackboard surfaces.] [Pass doors.] [Storage
pocket doors.]
1.4 MANUFACTURERS
A. Advanced Equipment.
B.
Modernfold, Inc.
C.
Panelfold, Inc.
D. Hufcor/Potomac, In
END OF SECTION
OPERABLE PARTITIONS
10 22 26 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
OPERABLE PARTITIONS
10 22 26 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 28 00 - TOILET ACCESSORIES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Toilet accessories and metal framed mirrors.
1.2 PRODUCTS
A. Toilet
1.
2.
3.
4.
5.
6.
7.
Accessories:
Paper towel dispensers.
Toilet tissue dispensers.
Waste receptacles.
Grab bars.
Sanitary napkin vendors.
Sanitary napkin disposal units.
Soap dispensers, wall mounted.
B. Mirrors and Frames:
1.
Glazing: Mirror glass, 1/4 inch thick, ASTM C 1036.
2.
Frames: Stainless steel.
C. Materials and Finishes:
1. Stainless Steel: ASTM A 666, Type 304, with No. 4 polished finish.
1.3 MANUFACTURERS
A. American Specialties, Inc.
B.
A & J Washroom Accessories, Inc.
C.
Bobrick Washroom Equipment, Inc.
D. Bradley Corporation.
END OF SECTION
TOILET ACCESSORIES
10 28 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
TOILET ACCESSORIES
10 28 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 44 00 - FIRE PROTECTION
SPECIALTIES PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Fire extinguisher mounting brackets.
B.
Fire extinguisher cabinets.
C.
Portable fire extinguishers.
1.2 QUALITY ASSURANCE
A. Standards: UL and FM listed products.
1.3 PRODUCTS
A. Cabinets:
1.
Mounting: Recessed.
2.
Trim: Exposed.
3.
Doors: Enameled steel, baked enamel finish.
4.
Door Style: Duo-panel.
B. Fire Extinguishers:
1.
Multipurpose Dry Chemical Type: UL-rated 4-A:60-B:C, 10 lb nominal capacity, in
enameled steel container.
2.
Public Area Mounting: Cabinet mounted.
3.
Service Area Mounting: Metal brackets.
1.4 MANUFACTURERS
A. J.L. Industries, Inc.
B.
Larsen's Manufacturing Company.
C. Potter-Roemer; Div. of Smith Industries, Inc.
D. Watrous; Div. of American Specialties, Inc. END OF
SECTION
FIRE PROTECTION SPECIALTIES
10 44 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
FIRE PROTECTION SPECIALTIES
10 44 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 50 00 - LOCKERS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Knock-down standard metal lockers.
1.2 PRODUCTS
A. Wardrobe Lockers:
1.
Type: Knock-down type, sheet steel, 20 gage top and bottom, 24 gage back and sides and
14 gage doors.
2.
Tier: Single-tier lockers.
3.
Face: Solid.
4.
Tops: Continuously sloped.
5.
Mounting for Student Lockers: Elevated base.
6.
Mounting for Maintenance/Kitchen Personnel: [Continuous ‘Z’ base.] [Elevated base.]
7.
Handle and Latch: [Recessed, single-point.] [Projecting,3-point.]
8.
Locking: [Built-in combination lock] [Padlock type.]
B. Athletic Lockers:
1.
Type: Knock-down type, sheet steel, 16 gage top and bottom, 18 gage back, and 14
gage doors.
2.
Tiers: [Single-tier lockers.] [Double-tier lockers.] [Multiple-tier lockers.]
3.
Face: [Solid with punched louvers.] [Perforated.]
4.
Tops: Continuously sloped.
5.
Mounting: Elevated base.
6.
Handle and Latch: [Recessed, single-point.] [Projecting,3-point.]
7.
Locking: [Built-in combination lock.] [Padlock type.]
C. Accessories:
1.
Number plates
2.
Base filler panels.
3.
Filler strips.
1.3 MANUFACTURERS
A. Republic Storage Systems Co., Inc.
B.
Art Metal Products; Div. of Fort Knox Storage Co.
C.
List Industries, Inc.
D. Lyon Metal Products, Inc.
E.
Penco Products, Inc.
END OF SECTION
LOCKERS
10 50 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
LOCKERS
10 50 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 56 13 - METAL STORAGE SHELVING
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Metal Storage Shelving.
1.2 PRODUCTS
A. Metal storage shelving system:
1.
Shelves: Rolled steel box form shelves; 20 gage.
2.
Posts: 14 gage steel angles.
3.
Rear and Side Bracing: 12 gage, X-type.
4.
Shelving Height: 87 inches.
1.3 MANUFACTURERS
A. Republic Storage Systems.
B.
Penco Products, Inc..
C.
Lyon Metal Products.
END OF SECTION
METAL STORAGE SHELVING
10 56 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
METAL STORAGE SHELVING
10 56 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 73 00 - PROTECTIVE COVERS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Extruded aluminum canopies.
1.2 PRODUCTS
A. Design, fabricate and installation of protective covers to withstand loads from gravity, wind,
snow drift and structural movement.
B.
Aluminum: 6063 alloy, heat treated to T-6 temper.
C.
Fasteners: 300 stainless steel.
D. Concealed Drainage system.
1.3 MANUFACTURERS
A. Mapes Industries, Inc, - Super Lumideck Hanger Rod Canopy.
B.
American Walkway Covers.
C.
Dittmer Architectural Aluminum.
END OF SECTION
PROTECTIVE COVERS
10 73 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
PROTECTIVE COVERS
10 73 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 10 75 00 - FLAGPOLES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Ground-set flagpole systems.
1.2 PRODUCTS
A. Aluminum flagpoles:
1.
Shape: Cone tapered.
2.
Height: [25 ft.] [35 ft.]
3.
Material: ASTM B 241, alloy 6063-T6, seamless tubing, minimum wall thickness 3/16
inch.
4.
Finish: Clear anodized.
5.
Fittings: [External] [Internal] halyard, finial ball, trucks and cleats.
6.
Finial: Ball.
7.
Flag Fasteners: Flag snaps with neoprene or vinyl covers.
1.3 MANUFACTURERS
A. American Flagpole; A Kearney-National Inc. Company.
B.
Baartol Co., Inc. (The)
C.
Concord Industries, Inc.
D. Eder Flag Manufacturing Company, Inc.
E.
Ewing International.
F.
Lingo, Inc.
G. Morgan-Francis Div.; Original Tractor Cab Co., Inc.
H. Pole-Tech Company Inc.
END OF SECTION
FLAGPOLES
10 75 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
FLAGPOLES
10 75 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 13 00 - LOADING DOCK EQUIPMENT
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Dock bumpers of reinforced rubber with attachment frame.
1.2 PRODUCTS
A. Bumpers: Fabric reinforced rubber pads, ozone resistant, laminated and compressed in
position with two galvanized steel rods with threaded ends, washers and nuts; between 3
2-1/2 x 1/4 inch galvanized steel angle end plates:
1.
Projection From Wall: 4-1/2 inches.
2.
Vertical Height: 10 inches.
3.
Length: 15 inches.
B. Attachment Hardware: 3/4 inch diameter galvanized bolts and expansion shields.
x
C. Touch-up Primer: Zinc rich type.
1.3 MANUFACTURERS
A. Dock
1.
2.
3.
4.
Bumpers:
Blue Giant Equipment Corporation: www.bluegiant.com.
Chalfant Sewing Fabricators, Inc.: www.chalfantusa.com.
Durable Corp: www.durablecorp.com.
Pawling Corp.: www.pawling.com.
END OF SECTION
LOADING DOCK EQUIPMENT
11 13 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
LOADING DOCK EQUIPMENT
11 13 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 31 00 - APPLIANCES
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Energy Star compliant appliances.
1.2 PRODUCTS
A. Appliances:
1.
Cooking equipment, including ranges and microwave ovens.
2.
Range hoods.
3.
Refrigerator/freezers.
1.3 MANUFACTURERS
A. Amana Refrigeration, Inc.
B.
Frigidaire Appliance Co.
C.
General Electric Company
D. Hotpoint.
E.
Whirlpool Corporation.
END OF SECTION
APPLIANCES
11 31 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
APPLIANCES
11 31 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 40 00 - FOOD SERVICE EQUIPMENT
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Commercial Food Service Equipment:
1.
Receiving and handling equipment.
2.
Food storage and refrigeration equipment.
3.
Food preparation equipment and exhaust hoods with integral fire suppression system.
4.
Food preparation line.
5.
Cafeteria line serving equipment.
6.
Pot washing and dishwashing equipment.
7.
Garbage collection and storage equipment.
1.2 QUALITY ASSURANCE
A. Codes and Standards:
1.
NSF Seal of Approval.
2.
Underwriters' Laboratories Label.
3.
NFPA 54, National Fuel Gas Code.
4.
NFPA 70, National Electrical Code.
5.
NFPA 96, Removal of Smoke and Grease-Laden Vapors from Commercial
Cooking Equipment.
6.
ASME Boiler Code.
1.3 PRODUCTS
A. Food Service Equipment Materials:
1.
Stainless Steel: AISI Type 304, No. 4 polished finish.
2.
Tops, Sinks, Dishtables, and Drainboards: 14 gage stainless steel.
3.
Cabinet Bodies and Doors: 20 gage stainless steel.
4.
Drawers: 18 gage stainless steel body with 16 gage stainless steel front.
5.
Shelves: 14 gage stainless steel.
6.
Cold Pans: 14 gage stainless steel..
B. Exhaust Hoods: NFPA 96, light fixtures, exhaust duct, grease removal.
C. Refrigeration Equipment: Compressors, condensers, piping, and storage areas, capacity as
required for projected quantities.
END OF SECTION
FOOD SERVICE EQUIPMENT
11 40 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
FOOD SERVICE EQUIPMENT
11 40 00 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 51 19 - BOOK THEFT PROTECTION EQUIPMENT
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Library book security system.
1.2 PRODUCTS
A. Detection System: Single-corridor system with audible and visible alarms; 43-inch-wide
aisles; mounted directly to floor, complete with all magnetic media; with 10-foot power cord
complying with the following requirements:
1.
Connecting cables buried in concrete floor.
2.
Remote digital electronics.
3.
Very low frequency system.
4.
Adjustable height detection zone.
5.
Keyed on/off switch.
6.
Provide a remote re-set switch at the circulation desk.
7.
Available Products: 3M Library Systems; Detection System Model 3501.
B. Accessories:
1 . D e s e n si t i ze r U n i t f o r P r i nt Ma t er i a l : D e s kt o p u n i t f o r
d e s e ns i t i zi n g s e cu r i t y s t r i p s o n n o n ma gn e t i c ma t e r i a l s . a .
A va i l a b l e P r od u ct : 3M L i br ar y S ys t e ms ; M o d el 9 3 0 .
2 . Book Check Unit: Desensitizes or resensitizes security strips on nonmagnetic materials.
a. Available Product: 3M Library Systems; Model 955.
3 . Desensitizer and Resensitizer Unit for Non-print Materials: Desensitizes and resensitizes
security strips on videocassettes, DVDs, and CDs without removing from cases. a.
Available Product: 3M Library Systems; Model 325.
4 . Provide the following security strips:
a. For Hardcover Books: 4 cases of 5,000 strips per case.
b. For Periodicals: 1 case of 5,000 strips.
c. For CDs, CD-ROMs, and Single-sided DVDs: 1 case of 1,000 strips.
d. For Videocassettes: 1 case of 1,000 strips.
END OF SECTION
BOOK THEFT PROTECTION EQUIPMENT
11 51 19 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
BOOK THEFT PROTECTION EQUIPMENT
11 51 19 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 51 23 - LIBRARY STACK SYSTEMS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Modular wood library shelving with [wood] [steel] shelves.
1.2 PRODUCTS
A. Steel Library Shelving Units:
1.
Construction: One-piece, welded-frame units.
2.
Shelving: Steel, adjustable.
3.
End Panels: 1-1/8-inch core with [birch] [oak] cherry] veneer faces and edges.
4.
Tops: Plastic laminate on 42-inch high units.
5.
Unit Heights: [42] [63] [78] inches.
6.
Shelf Depth: 12 inch shelf depth
B. Wood Library Shelving Units:
1.
Shelving Uprights: 1-inch core with wood veneer faces and edges.
2.
Shelving: 1-inch core with [wood,] [steel,] adjustable shelves.
3.
Wood Veneer: [Birch.] [Oak.] [Cherry.]
4.
Tops: Plastic laminate on 42-inch high units.
5.
Unit Heights: [42] [63] [82] inches.
6.
Shelf Depth: 12 inches.
C. Accessories:
1.
Dictionary stand.
2.
Atlas case.
3.
Magazine shelving.
1.3 MANUFACTURERS
A. Steel Library Shelving with Wood End Panels:
1.
Estey, Div of Tennsco Corp.
2.
M.J. Industries.
3.
Wilsonstak Library Shelving; Borroughs Corporation.
B. Wood Library Shelving:
1.
Brodart.
2.
The Worden Company.
3.
Library Bureau.
END OF SECTION
LIBRARY STACK SYSTEMS
11 51 23 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
LIBRARY STACK SYSTEMS
11 51 23 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 52 13 - PROJECTION SCREENS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Projection screens.
1.2 PRODUCTS
A. Front Projection Screens:
1. Operation:
a. Manual; [60 x 60] inches.
b. Electric; [108 x 144] [inches at Platform].
2. Mounting: [Wall-mounted.] [Surface mounting at ceiling.] [Recessed mounting at
ceiling.]
3. Viewing Surface: Matte white surface.
4. Edge Treatment: Black masking borders.
1.3 MANUFACTURERS
A. Bretford Manufacturing , Inc.
B.
Da-Lite Screen Co., Inc.
C.
Draper Shade & Screen co.
D. Stewart Filmscreen Corp.
END OF SECTION
PROJECTION SCREENS
11 52 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
PROJECTION SCREENS
11 52 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 61 42 - PLATFORM CURTAINS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Stage Curtains and Tracks:
1.
Front setting including valance, and front curtains.
2.
Cyclorama setting including borders.
1.2 QUALITY ASSURANCE
A. Fire Resistance Requirements: NFPA 701.
1.3 PRODUCTS
A. Main Act Curtain: Woven cotton velour with lining.
B.
Border and Cyclorama Curtains: Cotton Repp fabric.
C.
Tracks and Accessories:
1.
Front Curtains: Heavy-duty track system.
2.
Border and Cyclorama Curtains: Medium-duty track system.
3.
Track Channels: Galvanized steel
1.4 MANUFACTURERS
A. Front Setting Curtain:
1.
JB Martin Ltd.
2.
J.L. de Ball America, Inc.
3.
KM Fabrics, Inc.
B. Tracks:
1. Automatic Devices Company.
END OF SECTION
PLATFORM CURTAINS
11 61 42 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
PLATFORM CURTAINS
11 61 42 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 66 23 - GYMNASIUM EQUIPMENT
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Gymnasium equipment.
1.2 PRODUCTS
A. Main Court Basketball Backboards and Goals: Ceiling suspended, forward folding, [rear
braced] [front-braced] backstop with rectangular glass backboard, [adjustable for 8 to 10 ft in
height.]
B.
Side Courts [and Auxiliary Gymnasium] Basketball Backboard and Goals: Ceiling suspended,
forward folding, [rear-braced] [front-braced] backstop, with fan shaped molded fiberglass
backboard, [adjustable for 8 to 10 ft height.]
C.
Wall Padding: Panels 2'-0" wide x 5'-10" high, constructed of filler cemented to 3/8" backing
board and covered with flame retardant, vinyl-coated polyester material and flame barrier
interliner, mounted with Z-clips for panels without nailing margins.
D. Climbing Ropes: Dacron climbing ropes, with boot end, tambourine, rope hoist and safety
guards, including ceiling attachments, wall brackets, hardware and miscellaneous accessories.
E.
Wall-Mounted Chinning Bars: Fabricated with welded steel framework with no exposed
adjustment anchors and 6-inch incremental height adjustments.
F.
Volleyball Equipment: Indoor volleyball sets, consisting of recessed floor sleeves, 3-1/2-inch
diameter steel standards, and nylon mesh nets.
G. Badminton Equipment: Indoor badminton equipment, consisting of recess mounting flange,
2-3/4-inch diameter steel uprights, and netting with 3/4-inch openings.
H. Divider Curtain: Center-roll divider curtain; fabricated into one continuous section for the full
width of opening, with vinyl-coated polyester lower section and open polyester fabric upper
section, and operated electrically with key switch.
I.
Overhead Mat Mover: Hoist construction consisting of two independent, steel frame subassemblies with drive and lifting mechanisms enclosed, capable of lifting and supporting a
standard 45 by 45 ft wrestling mat weighing one lb/sq ft.
J.
Scoreboards and Shot Timers: For basketball-wrestling-volleyball; with all necessary cable
and connectors; controllers, and protective wire cages.
1.3 MANUFACTURERS
A. American Athletic, Inc.
B.
Jaypro Sports, Inc.
C.
Performance Sports Systems, Inc.
D. Porter Athletic Equipment Co.
END OF SECTION
GYMNASIUM EQUIPMENT
11 66 23 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
GYMNASIUM EQUIPMENT
11 66 23 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 11 66 53 - GYMNASIUM DIVIDERS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Roll-up gymnasium divider curtain.
1.2 PRODUCT
A. Basis-of-Design: Roll-Up Curtain similar to Porter Model No. 675.
B.
Construct solid lower 8 foot section of curtain minimum 18 ounce vinyl, polyester reinforced
fabric, containing anti-bacterial, fungi-resistant and flame retardant chemicals.
C.
Construct upper net section of open polyester type interlocking grid weave coated with
polyvinyl chloride with an approximate 80 to 85 percent open area and approximate eight of
7 ounces per square yard; flame resistant
1.3 MANUFACTURERS
A. American Athletic, Inc.
B.
Jaypro Sports, Inc.
C.
Performance Sports Systems, Inc.
D. Porter Athletic Equipment Co.
END OF SECTION
GYMNASIUM DIVIDERS
11 66 53 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
GYMNASIUM DIVIDERS
11 66 53 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 12 24 13 - WINDOW SHADE SYSTEMS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Roller shades and motorized shade operators.
1.2 PRODUCTS
A. Shade Band Material: PVC-coated fiberglass and polyester blends.
B.
Shade Operation: [Manual.] [Motorized operator.]
C.
Mounting: [Fascia with top/back cover.] [Recessed in ceiling pocket.]
D. [Audiovisual Light-Blocking Shades with side and perimeter seals.]
1.3 MANUFACTURERS
A. MechoShade Systems, Inc.
B.
Silientgliss USA, Inc.
C.
Solarfective/Accent Architectural.
END OF SECTION
WINDOW SHADE SYSTEMS
12 24 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
WINDOW SHADE SYSTEMS
12 24 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 12 35 50 - EDUCATIONAL CASEWORK
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Prefabricated modular educational casework.
1.2 PRODUCTS
A. Casework:
1. Materials:
a. Plastic laminate, NEMA LD3, VGS Grade.
b. Core - Doors: 45-lb density particleboard.
c. Core - Boxes: [45-lb density particleboard with exterior grade plywood ladder base.]
[Plywood].
2. Face Style: Flush overlay.
3. Frame Fabrication: Face frame.
4. Edging: Rigid PVC extrusion.
B. Counters:
1. Materials: Plastic laminate, NEMA LD3, HGS Grade, with 45-lb density particleboard
substrate.
1.3 MANUFACTURERS
A. Case Systems, Inc.
B.
LSI Corp. of America, Inc.
C.
Stevens Cabinet Company, Inc.
D. TMI Systems Design Corporation.
END OF SECTION
EDUCATIONAL CASEWORK
12 35 50 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
EDUCATIONAL CASEWORK
12 35 50 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 12 35 51 - MUSIC INSTRUMENT STORAGE
CABINETS PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Musical instrument and uniform cabinet system.
1.2 PRODUCTS
A. Cabinet Wall Panels: 3/4 inch thick industrial grade particleboard, minimum 48 pcf with
thermoset polyester laminate on both sides.
B.
Wood Doors: Same construction as cabinet wall panels.
C.
Finish: Maple (Timber Products Plank Maple Birch).
D. Hinges: 5-knuckle institutional type hinge, fastened to cabinet and door with through-bolt
construction.
E.
Grille Doors: Welded steel grille construction with powder coat finish.
F.
Locking slide-bolt designed for padlocks, with strike plate: 12 gage steel; with clear plastic
label holder for identification card insert.
G. Edging: Heat bonded 3mm beveled PVC edge-banding.
1.3 MANUFACTURERS
A. Wenger Corporation.
B.
Case Systems, Inc.
END OF SECTION
MUSIC INSTRUMENT STORAGE CABINETS
12 35 51 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
MUSIC INSTRUMENT STORAGE CABINETS
12 35 51 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 12 35 53 - LABORATORY CASEWORK
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Laboratory casework, countertops, sinks, and service fixtures.
1.2 PRODUCTS
A. Wood Casework:
1.
Materials: Solid wood and veneer plywood, premium grade birch or maple.
2.
Finish: Chemical-resistant finish.
B. Countertops:
1.
Material: Epoxy resin., plastic laminate, maple wood types.
2.
Chemical Resistance: Resistant to anticipated exposure.
C. Sinks, Cup Sinks, and Troughs: (No sinks at student stations)
1.
Material: Cast epoxy resin.
2.
Chemical Resistance: Resistant to anticipated exposure.
D. Service Fixtures: (Gas at teacher's station only)
1.
Piped Service: Air, gas, vacuum, steam, hot water, cold water, and distilled water.
2.
Power: Electrical service outlets.
1.3 MANUFACTURERS
A. Campbell-Rhea.
B.
Sheldon/Div. General Equipment Manufacturers.
C.
Kewaunee.
D. Leonard Peterson.
END OF SECTION
LABORATORY CASEWORK
12 35 53 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
LABORATORY CASEWORK
12 35 53 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 12 48 13 - ENTRANCE FLOOR MATS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Floor Mats and Frames.
1.2 PRODUCTS
A. Floor Mats:
1.
Type: Roll-up, aluminum link-type mats.
2.
Mounting: Recessed in metal frame.
B. Frame:
1.
Material: Extruded aluminum, ASTM B 221, alloy 6063-T5.
2.
Aluminum Finish: Clear anodized finish.
1.3 MANUFACTURERS
A. Arden Architectural Specialties, Inc.
B.
Construction Specialties, Inc.
C.
J.L. Industries.
D. Mats, Inc.
E.
Metalines, Div. of Balco, Inc.
F.
Pawling Corp.
G. Reese Enterprises, Inc.
END OF SECTION
ENTRANCE FLOOR MATS
12 48 13 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ENTRANCE FLOOR MATS
12 48 13 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 14 20 10 - ELEVATORS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Passenger hydraulic elevator.
1.2 QUALITY ASSURANCE
A. ICC/ANSI A117.1 Accessible and Usable Buildings and Facilities
B.
ADAAG – Accessibility Guidelines for Buildings and Facilities
C.
ANSI/NFPA 70, National Electrical Code
D. ANSI/NFPA 80, Standard for Fire Doors and Fire Windows
E.
ASME/ANSI A17.1, Safety Code for Elevators and Escalators.
1.3 PRODUCTS
A. Passenger Hydraulic Elevator Basis-of-Design: HydroFit Machine Room-Less, Hole-Less
Hydraulic Elevator by Otis Elevator Company.
1. Quantity of Elevators: 1
2. Number of Landings: 2
3. Number of Openings: 2
a. Front: 2
b. Rear: 0
4. Travel: 26'-6"
5. Rated Capacity/Speed: 3500 pounds, 125 fpm
6. Car Inside: 6’ 5-9/16”W x 5’ 5-9/16”D
7. Ceiling Type: Brushed Stainless Steel with 4 LED lights.
8. Cab Height: 8’ 9”'
9. The clear height under ceiling shall be 8’ 0” with 1-1/4” floor recess.
10. Entrance Width & Type: 3’ 6” x 7’ 0” Single-Slide, Brushed Stainless Steel.
11. Main Power Supply: 208 Volts, standby power operation.
12. Operation: Simplex
13. Machine Location: No machine-room required, Controller located inside hoistway.
14. Maintenance Service Period: 12 Months
1.4 MANUFACTURERS
A. Canton Elevator
B.
CEMCOLift, Inc.
C.
Elevator Equipment Co.
D. Minnesota Elevator Inc.
E.
Schindler Elevator Corp.
F.
Otis Elevator Co.
END OF SECTION
ELEVATORS
14 20 10 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
ELEVATORS
14 20 10 - 2
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
SECTION 14 42 00 - WHEELCHAIR LIFTS
PROJECT INCLUDES
1.1 SECTION SUMMARY
A. Vertical wheelchair lifts.
1.2 QUALITY ASSURANCE
A. Safety Code: ASME/ANSI A17.1 and local regulations.
1.3 PRODUCTS
A. Features and Components:
1.
Type: Pre-engineered lift systems.
2.
Finishes: Enameled steel.
3.
Controls: Solid state controls, key-operated.
4.
Structure: Self-supporting.
1.4 SCHEDULE
A. Wheelchair Lift Schedule:
1.
Capacity: 750 pounds.
2.
Rated Speed: 9 feet per minute.
3.
Power Supply: 110 volt, 1 phase, 60 Hz.
4.
Platform: 12 sq ft with 42-inch sides.
1.5 MANUFACTURERS
A. Concord Elevator Inc.
B.
Inclinator Company of America.
C.
National Wheel-O-Vator Co. Inc.
D. Garaventa.
END OF SECTION
WHEELCHAIR LIFTS
14 42 00 - 1
Grimm + Parker Architects Project No. 21145.00
NEW JKES AND FDES EXPANSION
WINCHESTER PUBLIC SCHOOLS
WHEELCHAIR LIFTS
14 42 00 - 2