Eagle Plan
Wear Surface Self-Leveling Topping Compound
Description
EAGLE PLAN is a fast-curing, polymer modified, cementitious self-leveling mortar that
allows smoothing and leveling of interior wood and concrete floors rapidly with less
work. This mortar can be used as a wear surface but also as an underlayment at
thickness varying from 2 mm to 25 mm (1/8” to 1”). This compound allows smooth
surfaces for installation of carpet, ceramic tiles, natural stone, hardwood, vinyl tiles and
resilient floor covering. This self-leveling product can also be used over a low
temperature radiant heating system installed on floors.
Surface Preparation
All surfaces to be covered shall be structurally sound, clean and free from traces of dust,
oil, grease, wax, paint, curing agent, coatings and loose particles. They must also be
exempt from any trace or presence of acids, concentrated alkalis, chemical cleaning
agent or any other material that can reduce adhesion. All concrete substrates shall be
completely cured and at least 28 days old. It must be roughened for more adhesion and
to remove completely all traces of paint, coating, loosely bonded toppings, loose
particles and construction debris. If concrete is too dry and porous, saturate concrete
surface with clean water within few hours before repairs leaving no excess water and
apply mortar when surface is dry again. Use of Eagle Prime Plus as primer is a good
alternative to concrete water saturation. Wood floors should be composed of new
exterior grade plywood, used only in interior dry floors. Plywood should be supported by
joists spaced every 40 cm (16”), the substrate consisting of two plywood sheets of
16mm (5/8”) thick each superposed cross-directionally, while allowing a minimum of 3
mm (1/8”) spacing between them and screwed at intervals of 15 cm (6”) around the
perimeter and 20 cm (8”) centrally. Maximum deflection should not exceed 1/360 of
span. When using a self-leveling product over a radiant heating system, it is necessary
to turn off 24 hours prior to installation and wait a week before turning it back on.
Ambient, surface and product temperature must be superior than 10ºC (50ºF) and lower
than 35ºC (95ºF) before the installation and for the first 24 hours.
Mixing
In a clean container, pour exactly 4.77 litres of fresh clean water and gradually add 22.7
kg of Eagle Plan powder while mixing with a low-speed drill and a mixer. Blend for 2 to 3
minutes scraping recipient walls and paddle to obtain a homogeneous malleable and
lump-free consistency is achieved. Slake for 5 minutes and mix again for 1 minute. Apply
immediately. Clean working tools and hands with water while product is still fresh.
Condor Chimiques Inc.
2645 B, Terra-Jet, St-Cyrille-de-Wendover, Québec, J1Z 1B3
www.condor.pro
info@condor.pro
Phone.: 819-474-6661
Fax.: 819-474-6681
Eagle Plan
Wear Surface Self-Leveling Topping Compound
Curing
Warning
Protect application from any direct ventilation or heat radiation sources, such as
direct sunlight during and after application for a minimum of 24 hours. These
conditions could cause micro-cracking. Eagle Plan takes 2 to 3 hours to set,
depending on consistency and ambient conditions. Curing time may vary according
to temperature and humidity level. Wait 24 hours before light traffic.
Package
This product is available in 22.7 kg bag.
Storage
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened
container.
Technical Data Table
CARACTERISTICS
CURE
CORROSIVE: This product contains a
cementitious blend and may cause
eyes, skin and respiratory system
irritation. When using this product:
Wear safety glasses, gloves and a
NIOSH approved anti-dust mask. Keep
out of reach of children.
FIRST AID TREATEMENT: Skin contact:
Wash with soap and water. Eye contact:
Flush eyes immediately and abundantly
with water for 15 minutes keeping
eyelids opened. Consult a physician
immediately. Ingestion: DO NOT
INDUCE VOMITING. Give water if
conscious. Keep victim warm and call
immediately a physician.
EAGLE PLAN (21% WATER)
Working time
30 minutes
Set time initial / final ASTM C-191
1 :00 hour / 2 :30 hours
Time allowed before installing floor
covering or coating
16 to 24 hours depending
on ºT and R.H.
Self-leveling capacity
20 minutes
Density ASTM C-185
2.02 kg/l
Compressive strength ASTM C-109
24 hours
7 days
28 days
21 MPa (3046 PSI)
28 MPa (4061 PSI)
38 MPa (5511 PSI)
Flexural strength ASTM C-348
24 hours
7 days
28 days
8.5 MPa (1233 PSI)
12.0 MPa (1740 PSI)
12.0 MPa (1740 PSI)
Pull-out strength on concrete CSA
A23.2-6B
7 days
28 days
2.42 MPa (351 PSI)
2.47 MPa (351 PSI)
Total linear shrinkage ASTM C-157 (dry
curing)
-0.07%
Coverage per bags of 22,7 kg of product
2.23 m² (24 ft²) for 6 mm
(1/4”) thickness
* Dry Time dependent of surface porosity and temperature.
Warranty
The customer shall verify of the suitability of this product for the intended purpose.
Applicator's skill, weather and surface conditions being beyond manufacturer's
control, we limit our liability to replacement of defective material only in sealed
container, within 1 year of proof of purchase. FOB plant.
Condor Chimiques Inc.
2645 B, Terra-Jet, St-Cyrille-de-Wendover, Québec, J1Z 1B3
www.condor.pro
info@condor.pro
Phone.: 819-474-6661
Fax.: 819-474-6681
Powered by TCPDF (www.tcpdf.org)