JONES-BLAIR
™
TYPE OF COATING
Product: Acrylithane® HS2/HS or HS4
Acrylic Urethane, Primers, Reducers
NOTE: (USE ACRYLITHANE HS4 PRODUCTS IN CALIFORNIA DUE TO DIFFERENT REGULATIONS)
SHELL RVIe (Evolution) PROGRAM PAINT
FIELD APPLICATION PAINT GUIDE & POWERWASHING SPECIFICATIONS
APPLYING PAINT PRODUCTS
ON SERVICE STATIONS (New or Repaint)
JONES-BLAIR COMPANY
2728 Empire Central
Dallas, Texas 75235
1 (800) 492-9400
Order Placement:
Elida Rodriguez – Customer Service
Email: sales@jones-blair.com Office: (214) 353-1604
Customer Service/Sales Fax Line: 1 (800) 325-6321
Technical Information:
Kristal Bluemer - National Sales Manager – Imaging
Email: kbluemer@jones-blair.com Cell: 214-676-8542
The information data and suggestions contained herein are believed to be reliable based upon our knowledge and experience, however, it is
expressly declared that Seller does not guarantee the result to be obtained in Buyers processes. SELLER HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY OTHER
WARRANTY EXPRESSED OR IMPLIED as to any and all products and or suggestions described herein whether such products are used
along or in combination with other materials. Buyer must make its own determination of the suitability of any product for its use and the
completeness of any information contained herein. Nothing contained herein shall be construed to constitute inducement or recommendation
to practice any invention covered by any patent without authority from the owner of the patent.
©Jones-Blair Company 2003
©2003 Jones-Blair Company
TECHNICAL INFORMATION
FOR
USING JONES-BLAIR™ ACRYLITHANE® HS2/HS or HS4 ON
SERVICE STATIONS
NEW OR REPAINTING USING JONES-BLAIR ACRYLITHANE™HS3, HS, HS4
& Associated Primers for SHELL RVIe (Evolution) PROGRAM
Notes: Acrylithane™ HS2 & HS Urethane topcoats & Ureprime™ HS2 primers meet all current
VOC requirements except CA. California requires lower VOC products except RVIe Silver.
Others require Acrylithane HS4 topcoats and Ureprime to meet the lower VOC requirements.
SPECIAL NOTES:
Gray primer or a previous coat of gray paint is required prior to application of the SHELL RVIe
SILVER. Apply two thin even coats of SHELL RVIe Silver using 1/4” nap on roller cover.
SPECIAL NOTE AS OF NOVEMBER 4, 2009: Shell will continue to allow black or bronze
anodized aluminum storefronts to remain at conversion sites. If mullions are painted other
colors than approved Shell RVI colors they must be repainted Shell Silver.
Two finish coats of the various colors are specified over the appropriate primer.
Primers are mandatory for this program.
Mixing, Thinning, and Application Technique
Jones-Blair Acrylithane HS2 or HS (high solids) is a two component system and must be mixed.
A 3:1 mixing ratio is required. Mix one 3/4 gallon of Acrylithane base material with one (1) quart
of #99951 Acrylithane Catalyst. Up to one (1) quart of #21092 thinner may be added per gallon
of mixed paint. Thinning is recommended for spray application. For brush and roller application,
thinning is not normally required. Apply Acrylithane only to thoroughly dry surfaces. When
applying at temperatures exceeding 85oF, addition of as much as three fluid ounces (about onefifth pint) of #21093 drying retardant per gallon of Acrylithane is recommended. Use of drying
retardant prevents dry spray and undesired fast drying on the surface being covered as well as
on brushes and rollers. For application in temperatures between 35-45oF, it is recommended
that ¼-1/2 ounce (2-3 capfuls) of #99011 Accelerator be added per catalyzed gallon of
Acrylithane HS2 or #33010 Ureprime Primer.
Note: Acrylithane HS2 may be applied over any urethane of factory baked finishes, including
florapolymers, when dulled by sanding and priming with Ureprime® HS2 Epoxy Urethane Primer
#33010 White - Mix 3:1 ratio with 99951 catalyst same as Acrylithane HS2 topcoat.
Note: Apply two coats of recommended white primer over dark colors for good hide when
using yellow or red to topcoat. Two finish coats required.
New Metal Surfaces (Iron and Steel)
Surface must be clean and free from oil, grease, wax, and other foreign matter. Remove mill
scale and rust by sandblasting. If sandblasting is not practical, clean surfaces with power tools or
by hand scraping and wirebrushing. Prime with Jones-Blair #1500-077 White Multi Purpose HS
Primer or #1560-032 Gray. For maximum corrosion resistance in coastal areas, prime with
Jones-Blair #33010 White Ureprime Epoxy Urethane. One prime coat and two finish coats
required.
©2003 Jones-Blair Company
Previously Painted Metal Surfaces (Iron and Steel)
Surface must be clean and free from oil, grease, wax, and other foreign matter. Remove any rust
and loose paint by scraping and wire-brushing. Apply primer to any areas cleaned to bare metal
the same as described for new metal surfaces. Most aged alkyd and urethane enamels will
accept a new Acrylithane topcoat without lifting. To reduce the potential for lifting an existing
coating, a barrier coat of #1500-077 White Multi-Purpose HS Primer or #1560-032 Gray may be
applied before application of an Acrylithane finish coat. Apply two Acrylithane finish coats for
desired appearance.
Aluminum and Galvanized Surfaces such as Sign Cans, etc
Surface must be clean and free from oil, grease, wax and other foreign matter. Prime with JonesBlair #942 Mist Coat II® Zinc Chromate Primer for new sign cans or #3090 Multi Grip 2 Acrylic
White Metal Primer for other. Apply two Acrylithane finish coats for desired appearance.
New Masonry Surfaces (Block, Concrete, Rough-Textured Brick, Etc.
Surface must be clean and free from oil, grease, wax, and other foreign matter. Fill all porous
surfaces with Jones-Blair #3781 Latex Block Filler. Block filler is ready-mixed and may be
applied by brush, roller, or spray. For best results, spray and roller application should be followed
by brushing while the filler is still wet. Brushing will work the filler into pores and crevices to more
effectively prevent moisture penetration. A gallon of block filler will typically cover 50-150 square
feet depending on the surface. Use water for cleanup and thinning. For roller application, a 1/2
inch roller cover is recommended with block filler. Allow block filler to dry 24 to 48 hours before
applying finish coats.
Apply two coats of Acrylithane for desired appearance.
*NOTE: Acrylithane HS2 may be applied over any urethane coating when dulled by sanding and
priming with Ureprime #33010 two part primer.
Factory Applied Florapolymer Coatings
Acrylithane HS2 may be applied over any urethane or factory baked finishes including
florapolymer coatings when dulled by sanding and applying Ureprime HS2 Epoxy Urethane
Primer #33010 White. This is a two component product same as Acrylithane Topcoat.
Previously Painted Masonry Surfaces
Surface must be clean and free from oil, grease, wax and other foreign matter. Remove loose
and scaling paint by water blasting, scraping or wire-brushing. If fillers are removed by cleaning
the surface, fill again as required with Jones-Blair #3781 Latex Block Filler. Make any necessary
repairs with a concrete patching compound. Clean any chalky surfaces thoroughly with detergent
and water before application of topcoat. Let any wet surfaces dry thoroughly before applying
barrier or finish coats.
A barrier coat of Jones-Blair #1500-077 White Multi-Purpose HS Primer or #1560-032 Gray may
be applied over alkyd coatings to reduce potential for lifting by Acrylithane topcoat. Most aged
alkyd, latex and urethane enamels will accept a new Acrylithane topcoat without lifting.
Apply two coats of Acrylithane for desired appearance.
©2003 Jones-Blair Company
New Stucco Surfaces
Surface must be clean and free from oil, grease, wax, and other foreign matter including loose
stucco. New stucco should be allowed to cure 1-2 weeks in good drying condition before
applying prime coat. Prime with #3090 White or 3091 Gray Multi-Grip 2® Latex Primer and two
finish coats for desired appearance.
Previously Painted Stucco Surfaces
Surface must be clean and free from oil, grease, wax, and other foreign matter. Remove and
repair any loose or damaged stucco. Clean any chalky surfaces thoroughly with detergent and
water before application of topcoat. Let any wet surfaces dry thoroughly before applying barrier
or finish coats.
A barrier coat of Jones-Blair #1500-077 White Multi-Purpose Primer or #1560-032 Gray may be
applied over alkyd coating to reduce potential for lifting by Acrylithane topcoat. Most aged alkyd,
latex and urethane enamels will accept a new Acrylithane topcoat without lifting.
Apply two finish coats of Acrylithane HS2.
Unpainted Glazed Brick and Porcelain
Surface must be clean and free from oil, grease, wax, and other foreign matter. Apply prime coat
of Jones-Blair #33010 White Ureprime HS2 primer.
Apply two coats of Acrylithane for desired appearance.
* Previously Painted Glazed Brick and Porcelain
Surface must be clean and free from oil, grease, wax and other foreign matter. Remove loose
and scaling paint by water blasting, scraping, or wire-brushing. Apply prime coat of Jones-Blair
#33010 White Ureprime Primer to any areas where previous coatings are removed by cleaning
and surface preparation. Additionally, to reduce the potential for lifting an existing coating, a
barrier coat of the #1500-077 White Multi-Purpose HS Primer or #1560-032 Gray may be applied
before application of any Acrylithane finish coat. Most aged alkyd, latex and urethane enamels
will accept a new Acrylithane topcoat without lifting. Dull glossy surfaces by sanding. Apply one
prime coat and two finish coats for desired appearance.
Unpainted Common Brick, Stone-X and other Unpainted Cementous Surfaces
Surface must be clean and free from oil, grease, wax, and other foreign matter. Prime with
Jones-Blair #3090 White or 3091 Gray Multi-Grip 2 Latex where bridging of small cracks is
desired. Jones-Blair #3781 Acrylic Block Filler may also be used for this purpose when thinned
with water.
Apply two Acrylithane finish coats for desired appearance.
New Wood
Surface must be clean and free from oil, grease, wax, and other foreign matter. Fill cracks with
spackling paste. Ensure that surface is thoroughly dry before painting. No separate primer is
required. Acrylithane is self-priming.
Apply two coats of Acrylithane for desired appearance.
©2003 Jones-Blair Company
* Previously Painted Wood
Surface must be clean and free from oil, grease, wax and other foreign matter. Remove loose
and scaling paint by scraping or wire-brushing. Remove any mildew (wearing protective clothing,
gloves and safety goggles) by washing with a solution of household bleach, water and household
detergent (3 quarts water plus 1 quart bleach plus 1 cup detergent). Do not add ammonia to the
mixture. Rinse the washed surface thoroughly with clean water. Repair cracks with spackling
paste. Ensure that surface is thoroughly dry before painting. Most aged alkyd, latex and urethane
enamel will accept a new Acrylithane topcoat without lifting. To reduce the potential for lifting an
existing coating, a barrier coat of Jones-Blair #1500-077 Multi-Purpose HS Primer or #1560-032
Gray may be applied before application of an Acrylithane finish coat.
Apply two Acrylithane finish coats for desired appearance.
Recommended Application Equipment
Associated Tools for Proper Application:
NOTE: It is recommended to roller or brush apply the coatings due to potential of getting the
paint on vehicles or pedestrians when spray painting.
To help ensure ease of application and uniformity of finish, the following products are recommended.
No thinning normally required. When air or surface temperatures are above 80oF, up to six ounces of
JB #21093 Retarder may be used to slow drying. Clean tools with JB™ #21092 Reducer.
Should spray painting be used, the following equipment is recommended:
Spray, Air Atomized
Model Gun
Spray, Air Atomized
Air Cap
Fluid Atomizing
Tip
Pressure
FX
66
25-60 PSI
25-60 PSI
DeVilbiss MBC 510
Binks #18
# 704
63PB
Reduction:
Up to 25% with JB #21092 Reducer to mixed gallon. Up to three
ounces of JB #21093 Retarder may be added to prevent fast dry or
cobb-webbing in temperatures above 85oF.
Clean-up:
Clean equipment IMMEDIATELY after using.
Reducer for cleaning.
Airless Spray:
Pump Ratio
Fluid Tip
Fluid Pressure
30:1 - 35:1
.011 - .013
1800-2600 PSI
Use JB #21092
Reduction and Clean-up:
Same as for Air Spray. Use the following for roller applications.
JB Item #
Description
Rollers/Covers! Handles for rough surfaces (brick, block, etc.):
1/2” Nap Roller Cover
3/4” Nap Roller Cover
For smooth surfaces:
86922-1/4” Candy stripe roller cover
86704 1 size Elastic Vinyl Car Cover for cars that can’t be moved during painting.
©2003 Jones-Blair Company
JONES-BLAIR™
Technical Data Sheet
MANUFACTURERS OF QUALITY PAINT SINCE 1928
Protective Coatings®
DEW POINT OF MOIST AIR
It is generally not recommended to apply Jones-Blair Acrylithane® HS2 Aliphatic Polyurethane
Enamel or any Polyurethane Enamel any time the substrate (surface) temperature is within 50F
of the dew point.
This chart illustrates how to calculate the dew point:
DEW POINT OF MOIST AIR
Ambient Air Temperature
200F
-70F
300F
-10C
400F
40C
500F
100C
600F
100C
700F
210C
800F
270C
900F
320C
1000F
380C
1100F
430C
1200F
400C
R
90
180F
-80C
280F
-20C
370F
30C
470F
80C
570F
140C
670F
190C
770F
250C
870F
310C
970F
360C
1070F
420C
1 170F
470C
E
85
0
17 F
-80C
260F
-3oC
360F
20C
450F
70C
550F
130C
650F
180C
750F
240C
840F
290C
950F
350C
1040F
400C
1130F
450C
0
L
80
16 F
-9 C
25 F
-4 C
34 F
1C
44 F
7C
54 F
12 C
63 F
17 C
73 F
23 C
82 F
28 C
93 F
34 C
102 F
39 C
110 F
430C
A
75
0
15 F
-90C
240F
-40C
330F
10C
420F
60C
520F
110C
620F
170C
710F
220C
800F
270C
910F
330C
1000F
380C
1060F
420C
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
70
13 F
-11 C
22 F
-8 C
31 F
-1 C
40 F
4C
50 F
10 C
60 F
16 C
68 F
20 C
78 F
26 C
88 F
31 C
96 F
36 C
105 F
410C
65
0
12 F
-110C
200F
-70C
290F
-20C
360F
30C
470F
80C
570F
140C
660F
190C
760F
240C
850F
290C
930F
340C
1030F
390C
E
60
110F
-120C
190F
-70C
270F
-30C
360F
20C
450F
70C
550F
130C
640F
180C
730F
230C
830F
260C
920F
330C
1010F
380C
H
55
90F
-130C
170F
-80C
250F
-40C
340F
10C
430F
60C
530F
120C
610F
160C
700F
210C
800F
270C
890F
320C
960F
370C
U
50
60F
-140C
150F
-90C
230F
-50C
310F
-10C
400F
40C
500F
100C
590F
150C
670F
190C
770F
250C
860F
300C
940F
340C
M
45
40F
-160C
130F
-110C
210F
-60C
290F
-20C
370F
30C
470F
80C
580F
130C
640F
180C
730F
230C
820F
280C
910F
330C
I
40
10F
-170C
110F
-120C
180F
-80C
260F
-30C
350F
20C
430F
60C
520F
110C
610F
160C
690F
210C
780F
280C
870F
310C
D
35
0
-2 F
0
0
0
0
0
0
0
0
0
0
0
0
0
0
I
30
-60F
0
0
0
T
0
0
0
V
0
0
0
0
-19 C
0
8F
0
0
-13 C
16 F
-9 C
23 F
-5 C
31 F
-1 C
40 F
4C
48 F
9C
57 F
14 C
65 F
18 C
74 F
23 C
83 F
280C
-200C
40F
-160C
130F
-110C
200F
-70C
280F
-20C
360F
20C
44’F
70C
520F
110C
610F
160C
690F
210C
770F
250C
Example: If air temperature is 700F and relative humidity is 650F, the dew point is 570F
The information data and suggestions contained herein are believed to be reliable based upon our
knowledge and experience, however, it is expressly declared that Seller does not guarantee the result
to be obtained in Buyer’s processes. SELLER HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY
OTHER WARRANTY EXPRESSED OR IMPLIED as to any and all products and/or suggestions
described herein whether such products are used along or in combination with other materials. Buyer
must make its own determination of the suitability of any product for its use and the completeness of
any information contained herein. Nothing contained herein shall be construed to constitute
inducement or recommendation to practice any invention covered by any patent without authority from
the Owner of the patent.
Jones-Blair Company™ Dallas, TX 75235
©2003 Jones-Blair Company
Jones-Blair Company™ Power Washing Specifications
Power washing is required for all decks if repainting is required. Buildings and other structures should
also be power washed if they are to be painted.
Equipment
Power washing pumps should be capable of generating 3,000 to 4,000 psi and deliver 6-10 gpm of
wash/rinse water.
Fan type spray tips give varying spray angles. Fan tips are considered to be "scrapers" and/or "pushers".
The spray tips used should be selected for this program should be based on the area and surface to be
cleaned. Do not use a round tip or what is commonly referred to as a "shotgun", point tip or "0" tip.
Round tips used with high pressure may result in surface damage on wood, metal or masonry. This type
of spray tip is considered to be a "cutter".
High flow rate/low pressure machines will generally clean better than a low flow rate/high pressure
machine. Consult SSPC-SP12/NACE No. 5 "Surface Preparation and Cleaning of Steel and Other Hard
Materials by High and Ultrahigh Pressure Water Jetting Prior to Recoating" for additional information.
Cleaning Agents
There is a number of cleaning agents or detergents that can be used in conjunction with pressure
washers. Cleaning agents can dramatically improve cleaning efforts. Consult the manufacturer's
recommendations based on the type of surfaces to be cleaned. Also consider health, safety and
environmental issues when selecting the appropriate cleaner.
Do not use any solutions that are caustic soda (causes pitting of aluminum), chlorine (discolors all
metals), strong alkaline (will damage painted surfaces) or acid type cleaners that will deteriorate
galvanized metal or etch glass. The best cleaning agent for common soil types to remove grease, oil and
dirt is a medium duty alkaline (pH of 8 to 12) at about 3% concentration by volume for painted metal,
wood, and galvanized aluminum.
Regardless of the cleaning agents used, the surfaces cleaned must be thoroughly rinsed with clear water
to insure that the cleaning solution has been removed. Failure to thoroughly remove the cleaning agent
could result in poor paint adhesion when the surfaces are painted. All power washed surfaces must be
dry before painting.
Preparation and Power Washing
Cover all surfaces that might be damaged by power washing such as dispensers, automobiles, light
fixtures, cameras, foliage, etc. All surfaces should be scrubbed to remove contaminants. Heavily stained
areas may need pre-treatment. A minimum of two passes is required: one with cleaning solution and the
final rinse. All standing water should be removed from the site to ensure that there are no remaining
chemicals and to avoid spotting.
Reclamation
Contractor is expected to comply with all regulations regarding the disposal of wash and rinse water.
Local or state regulations may not permit these waters into the site storm drains, or, to be allowed to run
off site. For those areas that do have special reclamation requirements, contact the Project Manager.
©2003 Jones-Blair Company