295M AUTOMATIC FLUSHBOLT WITH FIRE BOLT
NOTES:
1. 295M CONSISTS OF ONE 292S AND ONE
AUXILLARY FIRE BOLT.
DRILL
2. 3 HR FIRE RATING FOR METAL DOORS UP
TO 4 FT. WIDE X 9 FT. TALL.
1"
25.3
4. DO NOT INSTALL THE ACTIVE DOOR
STRIKE IF GAP BETWEEN THE TWO
DOORS IS LESS THAN 3/16" [4.5].
3/8"
9.5
3/4"
18.8
BACKSET
1 11/16"
42.7
FRAME STOP
REVERSIBLE BOLT
HEAD GUIDE
#8 x 1" APS (2x)
1/2"
12.7
5/8"
16
1"
25.4
DOOR
CL
1/4"
ACTIVE DOOR 6.4
STRIKE
#8 x 1" APS (2x)
21/32"
16.8
SHIMS ARE
OPTIONAL
1/16"
1.5
SEE NOTE 4
1 5/8"
41.3
3/16"
4.8
1/16"
1.5
15/16"
23.8
1 1/4"
31.8
7/8"
22.2
ACTIVE
DOOR
2 9/32"
57.9
FRAME STRIKE
#8 x 1" APS (2x)
3. SEE PAGE 2 FOR DETAILS ON INSTALLING
FIRE BOLT.
INSTALL CURVED LIP ON
THE DOOR EDGE THAT
MAKES INITIAL CONTACT
WITH FLUSHBOLT ON
THE INACTIVE DOOR
METAL DOOR & FRAME PREP TEMPLATE
1-1/8" HOLE
2"
50.8
1/4"
6.5
3/4"
19.1
5/32"
3.9
REINFORCEMENT
NEEDED
CL
DOOR WITH RECESSED
TOP OR BOTTOM
12"
304.8
9/32"
6.7
14"
355.6
6 25/32"
172.2
6 1/4"
158.8
CL
3 13/32"
86.1
1/2"
12.7
1 1/32"
26.2
NOT TO SCALE
DIMENSIONS IN [ ] ARE IN MILLIMETERS
#8 x 1" APS (4x)
1/8"
3.2
2" MIN. CLEARANCE
50.8
NOTE: HAGER RESERVES THE RIGHT TO MAKE PART CHANGES AND IS NOT RESPONSIBLE FOR OBSOLETE DRAWING
ERRORS. TO ENSURE YOUR DRAWING IS CURRENT VISIT WWW.HAGERCO,COM.
TEMPLATE NO: T295M
DRAWING NO: T-TA00176
REV: 05
SHEET 1 OF 2
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
295M AUTOMATIC FLUSHBOLT WITH FIRE BOLT
METAL DOOR & FRAME PREP TEMPLATE
INACTIVE DOOR:
1.
MEASURE 4 - 6" FROM BOTTOM OF THE INACTIVE DOOR.
2.
DRILL A 9/16"[14.3] HOLE 1-5/8"[41.3] DEEP ON THE
CENTERLINE OF THE DOOR EDGE.
3.
INSERT FIRE BOLT AND STRIKE SQUARELY WITH A
HAMMER UNTIL IT SITS TIGHT AGAINST DOOR EDGE. (A
WOOD BLOCK MAY BE USED BETWEEN THE HAMMER AND
FIRE BOLT/PLUG TO PROTECT FINISH)
ACTIVE DOOR:
DRILL 1-1/8"[28.5] HOLE 7/8"[22.2] DEEP FOR THE PLUG
1.
(USE SAME HEIGHT DIMENSION AS USED IN THE FIRE BOLT
INSTALLATION)
2.
INSERT FIRE BOLT AND STRIKE SQUARELY WITH A
HAMMER UNTIL IT SITS TIGHT AGAINST DOOR EDGE. (A
WOOD BLOCK MAY BE USED BETWEEN THE HAMMER AND
FIRE BOLT/PLUG TO PROTECT FINISH)
3.
FOR ZERO CLEARANCE DOORS, COUNTERBORE 1-1/4"[31.7]
X 1/16"[1.6] DEEP FOR PLUG.
ACTIVE
DOOR
INACTIVE
DOOR
DRILL 9/16"[14.3] HOLE
1-5/8"[41.3] DEEP MIN.
CL
DRILL 1-1/8"[28.5] HOLE
7/8"[22.2] DEEP MIN.
CL
SPRING STEEL
LOCKING COLLAR
4 - 6"
4 - 6"
PLUG
FIRE BOLT
INACTIVE DOOR EDGE
ACTIVE DOOR EDGE
15/32"
11.7
13/32"
10.1
1 7/32"
31.3
25/32"
19.5
1 19/32"
40.5
1 9/16"
39.9
1/2"
12.3
1 3/32"
27.6
PLUG
FIRE BOLT
IMPORTANT: THE FIRE BOLT WILL PROJECT DURING A FIRE. DO NOT
COVER WITH ANY EDGE MOUNTED HARDWARE.
NOT TO SCALE
DIMENSIONS IN [ ] ARE IN MILLIMETERS
TEMPLATE NO:
DRAWING NO: T-TA00176
REV: 05
SHEET 2 OF 2
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149